Determination of lead in fine particulates by slurry sampling electrothermal atomic absorption spectrometry

A simple method for determining lead in fine particulates (PM_2.5) by using electrothermal atomic absorption spectrometry (ETAAS) has been developed. Particulates collected on Nuclepore filter by using a dichotomous sampler were suspended in diluted nitric acid after ultrasonic agitation. The dislodging efficiency is nearly 100% after agitation for 5 min. In order to study the suspension behavior of PM_2.5 in solvents, a Brookhaven ZetaPlus Particle Size Analyzer was used to determine the particle size distribution and suspension behavior of air particulates in the solvent. The pre-digestion and modification effect of nitric acid would be discussed. Palladium was added as a chemical modifier and the temperature program of ETAAS was changed in order to improve the recovery. The slurry was introduced directly into a graphite tube for atomization. The metal content in the sample was determined by the standard addition method. In addition, a conventional acid digestion procedure was applied to verify the efficiency of the slurry sampling method. It offers a quick and efficient alternative method for heavy metal characterization in fine particulates. Received: 2 August 2000 / Revised: 25 October 2000 / Accepted: 28 October 2000     

Determination of lead in fish samples by slurry sampling electrothermal atomic absorption spectrometry

Ultrasonic slurry sampling electrothermal atomic absorption spectrometry (USS-ETAAS) was been applied to the determination of lead in several fish samples. The influences of instrument operating conditions and slurry preparation on the signal were examined. Palladium and ammonium nitrate were used as the modifier to improve the signal. Since the sensitivity to lead in various fish slurries and aqueous solutions was different, the standard additions method was used for the determination of lead in these fish samples. The method was applied to the determination of lead in dogfish muscle reference material (DORM-2) and a swordfish muscle sample purchased from the local market. The analysis results agreed with the reference value. The accuracy was better than 6%. The precision between sample replicates was better than 16% with the USS-ETAAS method. The detection limit of lead estimated from standard additions curve was about 0.053-0.058 microgram g-1 in different samples.     

Determination of lead in biological samples by use of slurry sampling electrothermal atomic absorption spectrometry

Slurry-sampling electrothermal atomic absorption spectrometry has been applied to the determination of lead in several biological samples (fish and marine algae). The slurries were prepared both by magnetic shaking and microwave-heating and the effect of instrument operating conditions and slurry preparation conditions on the signal were examined. In addition, results from slurry sampling were compared with those obtained by microwave-assisted acid digestion of the same samples and no significant differences were found between them when the analysis of variance (ANOVA) was applied. The between-batch precision of the slurry techniques employed was similar to that for the microwave-assisted digestion procedure; values were always below 6.7%, except for the Dicentrarchus labrax sample for which the value obtained was 9.5% when using slurry magnetic shaking and 7.6% when using the slurry microwave heating. The accuracy of the slurry methodology employed was also evaluated by analysis of two biological reference materials (NIST-1577b and IAEA-V10); percentage recoveries obtained were between 95.6 and 98.5% of the values certified for lead.     

Determination of mercury in sewage sludges by slurry sampling electrothermal atomic absorption spectrometry

An electrothermal atomic absorption spectrometric procedure was developed for the determination of mercury in sewage sludge, in which the samples were suspended in a solution containing hydrofluoric and nitric acids. Silver nitrate (4%, m/v) and potassium permanganate (3%, m/v) were incorporated as matrix modifiers, and aliquots were directly introduced into the graphite furnace. A fast-heating program with no conventional pyrolysis step was used. The detection limit for mercury in a 50 mg/mL suspension was 0.1 microg/g. Calibration was performed by using aqueous standards. An analysis of certified reference materials confirmed the reliability of the procedure.     

Determination of aluminium and manganese in human scalp hair by electrothermal atomic absorption spectrometry using slurry sampling

Methods for the determination of aluminium and manganese in human scalp hair samples by electrothermal atomic absorption spectrometry using the slurry sampling technique were developed. Palladium and magnesium nitrate were used as chemical modifiers. Hair samples were pulverized using a zirconia vibrational mill ball, and were prepared as aqueous slurries. Determinations can be performed in the linear ranges of 1.9–150 μg l⁻¹ Al³⁺ and 0.03–10.0 μg l⁻¹ Mn²⁺. Limits of detection of 0.9 mg kg⁻¹ and 27.6 μg kg⁻¹ were obtained for aluminium and manganese, respectively. The analytical recoveries were between 99.6 and 101.8% for aluminium and in the 98.3–101.3% range for manganese. The repeatability of the methods (n=11), slurry preparation procedure and ETAAS measurement, was 16.0 and 7.9% for aluminium and manganese, respectively. The methods were finally applied to the aluminium and manganese determination in 25 scalp hair samples from healthy adults. The levels for aluminium were between 8.21 and 74.08 mg kg⁻¹, while concentrations between 0.03 and 1.20 mg kg⁻¹ were found for manganese.     

Determination of lead in hair and its segmental analysis by solid sampling electrothermal atomic absorption spectrometry

A rapid and practical solid sampling electrothermal atomic absorption spectrometric method was described for the determination of lead in scalp hair. Hair samples were washed once with acetone; thrice with distilled-deionized water and again once with acetone and dried at 75 °C. Typically 0.05 to 1.0 mg of dried samples were inserted on the platforms of solid sampling autosampler. The effects of pyrolysis temperature, atomization temperature, the amount of sample as well as addition of a modifier (Pd/Mg) and/or auxiliary digesting agents (hydrogen peroxide and nitric acid) and/or a surfactant (Triton X-100) on the recovery of lead were investigated. Hair samples were washed once with acetone; thrice with distilled-deionized water and again once with acetone and dried at 75 °C. Typically 0.05 to 1.0 mg of dried samples were inserted on the platforms of solid sampling autosampler. The limit of detection for lead (3σ, N = 10) was 0.3 ng/g The addition of modifier, acids, oxidant and surfactant hardly improved the results. Due to the risk of contamination and relatively high blank values, the lead in hair were determined directly without adding any reagent(s). Finally, the method was applied for the segmental determination of lead concentrations in hair of different persons which is important to know when and how much a person was exposed to the analyte. For this purpose, 0.5 cm of pieces were cut along the one or a few close strands and analyzed by solid sampling.     

Determination of lead and atmospheric particulates by flameless atomic absorption spectrometry

Flameless atomic absorption techniques were used to determine the lead and other atmospheric particulate in the city of Tehran. 640 samples were collected in 20 different stations around the city during four seasons in 1992. The radioactivity of the air samples was also measured by -ray spectrometry using high purity Ge/Li detectors, and a multichannel analyzer. The results were compared with previous measurements in the city of Tehran.     

Use of aqueous slurry sampling for the determination of lead in human hair samples by electrothermal atomic absorption spectrometry

A method for the determination of lead in human hair slurries by electrothermal atomic absorption spectrometry was optimized. Particle size reduction was achieved with a vibrational mill ball equipped with zirconia cups, 20 min being sufficient grinding time to achieve an adequate particle diameter (<1 mum). The use of different thickening agents, namely glycerol, Triton X-100 and Viscalex HV30, was studied and glycerol was found to be the best. The use of Pd and Mg(NO(3))(2) at optimum concentrations of 20 and 25 mg l(-1) respectively was found to be satisfactory for stabilizing lead at 1100 degrees C. A limit of detection of 0.21 mg kg(-1) was obtained. The limit of detection can be reduced to 0.05 mg kg(-1) without loss of analytical performance by increasing four-fold the amount of hair sample. Accuracy was studied by analysis of a CRM 397 human hair reference material with a certified lead content of 33.0 +/- 1.2 mg Pb kg(-1). The standard addition method was used for the determination of lead in hair samples from healthy people, the levels being between 2.3 and 35.5 mg kg(-1).     

Determination of lead in biological materials by constant-temperature electrothermal atomic absorption spectrometry

A comparison is made between a platform-equipped Perkin-Elmer HGA-500 and a recently designed two-step constant-temperature graphite furnace with respect to susceptibility to interference effects as well as attainable detection limits. It is shown that larger quantities of biological samples can be used with the constant-temperature furnace without suppressing the analyte signal, resulting in lower detection limits. Materials studied include NBS Olyster Tissue and Bovine Liver, and human lung tissue and human blood.     

电沉积-钨丝电热原子吸收光谱法测定水样中的铅

研制了一种便携式钨丝电热原子吸收光谱分析装置,其主要包括:钨丝电热原子化器、多道微型CCD光谱仪、仪器电源系统以及控制系统。并将电沉积分离富集技术与该钨丝电热原子吸收光谱分析仪器结合,完成环境水样中铅的现场分析。并对铅的电沉积条件作了研究,最佳电沉积电位为负650 mV(vs.SCE),方法检出限:0.20μg/L,线性范围:1~15μg/L,对4μg/L Pb标准溶液10次重复测试,RSD为4.4%。     

Determination of lead in waters by atomic absorption spectrometry with electrothermal atomization

Summary The electrothermal atomization of lead has been investigated for accurate determination of lead in water samples. Thiourea served to lower the atomization temperature of lead and to eliminate the interferences from chloride matrix. The addition of thiourea also allowed the accurate determination of lead irrespective of its chemical form. The absolute sensitivity (1% absorption) was 1.1 × 10^–12g of lead. The method permits the direct rapid determination of lead in water samples including sea water.

---

Bestimmung von Blei in Wässern durch Atomabsorptions-Spektrometrie mit elektrothermischer Atomisierung

Zusammenfassung Zur Verringerung der Atomisie-rungstemperatur und zur Beseitigung von Störungen durch die Chloridmatrix wird ein Zusatz von Thioharnstoff empfohlen. Dieser Zusatz gestattet außerdem eine genaue Bestimmung unabhängig von der chemischen Form, in der das Blei vorliegt. Die absolute Empfindlichkeit (1% Absorption) beträgt 1,1 · 10^–12 g Pb. Das Verfahren wurde zur direkten Bleibestimmung in Wässern, einschl. Meereswasser, angewendet.

     

Determination of nickel, chromium and cobalt in wheat flour using slurry sampling electrothermal atomic absorption spectrometry

The slurry technique was applied to the determination of Ni, Cr and Co in wheat flour by electrothermal atomic absorption spectrometry (ETAAS). The influence of the graphite furnace temperature programme was optimized. Optimum sensitivity was obtained by using a mixture of 15% HNO₃–10% H₂O₂ as suspended medium for a 3% w/v slurry in the determination of Ni; lower concentrations of HNO₃ were necessary for the determination of Co and Cr (viz. 5 and 10%). The precision of direct analyses of the slurries was improved by using mechanical agitation between measurements; thus, the RSD of the measurements was ca. 5% for repeatability. The direct slurry sampling (SS) technique is suitable for the determination of Ni and Cr in wheat flour samples at levels of 150–450 and 30–72 ng g⁻¹, respectively, as it provides results similar to those obtained by ashing the sample. However, the typically low level of Co in these samples precluded its determination by the proposed method (the study was made in an SRM spiked wholemeal flour), at least in those samples that were contaminated with elevated concentrations of the metal (viz. more than 90 ng of Co per g of flour). The method provides a relative standard deviation of 6, 8, and 4% for Ni, Cr, and Co, respectively.     

Slurry sampling for determination of lead in marine plankton by electrothermal atomic absorption spectrometry

A slurry sampling method has been developed for the determination of Pb in marine plankton by ETAAS using a freshwater plankton certified reference material (CRM 414). Slurries were prepared in 1–3% m/v range with 1% v/v HNO₃ by ultrasonic agitation for 5 min. The effects of several chemical modifiers, including Ir(NO₃)₂, Mg(NO₃)₂, Pd(NO₃)₂, Pd(NO₃)₂ + Mg(NO₃)₂, and Mg(NO₃)₂ + NH₄H₂PO₄, were investigated for the stabilization of Pb during thermal pretreatment. Lead in slurries was effectively stabilized up to 1000 °C with Ir, Pd and Pd + Mg modifiers among which Pd + Mg provided the best results with complete atomization at 1850 °C. Firings in the presence of Ir were, problematic due to ash formation inside the atomizer. Water, dilute HNO₃ and HF were examined as suspension medium. Dilute HNO₃ (1–2% v/v) proved to be advantageous over water as it afforded extraction of Pb from plankton almost quantitatively in 5 min agitation. Hydrofluoric acid was the least suitable medium. Increasing HF concentration up to 5% v/v resulted in inaccuracy and substantial background absorption. Fast-heating furnace method provided comparable accuracy and precision to that of conventional-heating in slurries of CRM 414. Detection limits and characteristic masses were, respectively, 0.49 μg L^− 1 and 32 pg for the conventional method and 0.62 μg L^− 1 and 37 pg for the fast-heating method. However, fast-heating approach suffered from distorted peaks at high temperatures and incomplete pyrolysis of matrix at lower temperatures. Analysis of marine plankton samples for Pb was performed by using the conventional furnace program. The results showed a high correlation with those obtained by solution ICP-MS. Differences were statistically insignificant within 95% confidence interval.     

Determination of tin in marine sediments by slurry sampling atomic absorption spectrometry with electrothermal atomization using a permanent modifier

A molecularly imprinted polymer (MIP) was synthesized by the precipitation polymerization method using triazophos (TAP) as the template. The MIP can selectively absorb TAP from sample solutions. The absorbed TAP strongly enhances the chemiluminescence (CL) of luminol-H₂O₂. This was applied to design a method for the on-line enrichment and detection of TAP. The change in CL intensity is linearly proportional to the concentration of TAP in the range from 1.0 μM to ~4.0 nM, and the detection limit is 2.5 nM (at an S/N of 3σ). This is about one order of magnitude lower than that of the conventional CL assay. The method was successfully applied to the determination of TAP in vegetable samples.     

Determination of cadmium in biological and environmental samples by slurry electrothermal atomic absorption spectrometry

The retention of cadmium by the bacteria Escherichia coli and Pseudomonas putida was optimized in order to develop a rapid and selective preconcentration method for cadmium from biological and environmental samples prior to determination by electrothermal atomic absorption spectrometry. Living and lyophilized cells for both bacteria were used, but the method using dead cells shows better analytical capabilities. Cadmium from aqueous solutions is easily retained on the outer membrane of both bacteria in the pH range 4-10, although the selected working pHs for E. coli and P. putida were 5 and 9, respectively. Cadmium retained by the bacteria was dispersed in 3.5 M nitric acid and the slurry was introduced directly into the graphite tube. The best sensitivity and detection limit were obtained for E. coli (0.03 ng ml(-1) and 0.04 ng ml(-1) respectively, in the absence of any chemical modifier). A strong spectral interference from nickel chloride was found and methods to overcome it were developed. The proposed extraction procedure was tested by the determination of cadmium in different standard biological and environmental samples.     

Determination of lead and cadmium in urine by electrothermal atomization atomic absorption spectrometry

The applicability of a DETATA sorbent to the preconcentration of lead and cadmium followed by the determination of these elements in urine using atomic absorption spectrometry with electrothermal atomization was demonstrated. After preconcentration by a factor of 10, the limits of detection were 0.01 and 0.2 μg/L for cadmium and lead, respectively. The accuracy of the results was supported by the analysis of Seronorm Trace Elements Urine (Batch no. 101021).     

Determination of cadmium and lead in mussels by tungsten coil electrothermal atomic absorption spectrometry

In this work it was evaluated the determination of Cd and Pb in mussels by tungsten coil electrothermal atomic absorption spectrometry (TCA-AAS). A critical and comprehensive study of the effects caused by Pd, Mg, ascorbic acid, and binary mixtures of these compounds on the atomization of Cd and Pb in acid digested solutions of mussels was performed. Palladium and mixtures containing it were useful to increase sensitivity and thermal stability of Cd and Pb. Additionally, the coil lifetime was increased and the background signals were decreased in these modifiers. All these favorable effects were analytically exploited to determine Cd and Pb in samples of mussels. The proposed methodology was validated using two certified reference materials (oyster tissue and mussel). No statistical difference was observed between determined and certified values at a 95% confidence level. Cadmium and Pb in Chilean bivalve mussels were determined by TCA and by graphite furnace-AAS. Again, the results showed statistical agreement.     

Determination of cadmium, chromium and lead in marine sediment slurry samples by electrothermal atomic absorption spectrometry using permanent modifiers

A procedure for the determination of cadmium, chromium, and lead in marine sediment slurries by electrothermal atomic absorption spectrometry is proposed. Slurry was prepared by mixing 10 mg of ground sample with particle size smaller than 50 μm completed to the weight of 1.0 g with a 3% nitric acid and 10% hydrogen peroxide solution. The slurry was maintained homogeneous with an aquarium air pump. For cadmium, the best results were obtained using iridium permanent with optimum pyrolysis and atomization temperatures of 400 and 1300 °C, respectively, a characteristic mass, m_o (1% absorption), of 2.3 pg (recommended 1 pg). Without modifier use, zirconium, ruthenium, and rhodium m_o were 3.4, 4.1, 4.6, and 4.8 pg, respectively. For chromium, the most sensitive condition was obtained with zirconium permanent with optimum pyrolysis and atomization temperatures of 1500 and 2500 °C, m_o of 6.6 pg (recommended 5.5 pg); and without modifier use, rhodium, iridium, and ruthenium m_o were 5.3, 8.8, 8.8, and 8.9 pg, respectively. For lead, the best modifier was also zirconium, m_o of 8.3 pg for the optimum pyrolysis and atomization temperatures of 600 and 1400 °C, respectively, (recommended m_o of 9.0 pg). For iridium, ruthenium, without modifier, and rhodium, m_o were 14.7, 15.5, 16.5, and 16.5 pg, respectively. For all the modifiers selected in each case, the peaks were symmetrical with r² higher than 0.99. Being analyzed (n = 10), two marine sediment reference materials (PACS-2 and MESS-2 from NRCC), the determined values, μg l⁻¹, and certified values in brackets, were 2.17 ± 0.05 (2.11 ± 0.15) and 0.25 ± 0.03 (0.24 ± 0.01) for cadmium in PACS-2 and MESS-2, respectively. For chromium in PACS-2 and MESS-2 the values were 94.7 ± 5.6 (90.7 ± 4.6) and 102.3 ± 10.7 (106 ± 8), respectively. Finally, for lead in PACS-2 and MESS-2, the results obtained were 184 ± 7 (183 ± 8) and of 25.2 ± 0.40 (21.9 ± 1.2), respectively. For cadmium and lead in both samples and chromium in PACS-2, calibration was accomplished with aqueous calibration curves. For chromium in MESS-2, only with the standard addition technique results were in agreement with the certified ones. The limits of detection (k = 3, n = 10) obtained with the diluents were 0.1, 3.4, and 3.6 μg l⁻¹ for cadmium, chromium, and lead, respectively.