Evaluation of radioactivity induced in the accelerator building and its application to decontamination work

For decommissioning of the cyclotron and electron synchrotron facilities, the residual radioactivity in surface and core samples of concrete, collected from various parts of buildings, was determined by gamma-ray spectrometry. It was found that the concrete samples were activated mainly by neutrons and that the major radioisotopes were ¹⁵²Eu, ⁶⁰Co, ¹³⁴Cs, ²²Na and ⁵⁴Mn. The maximum activity induced by thermal neutron capture was observed at the depth of 10 cm in the concrete wall near the deflector of the cyclotron. Tritium was also produced by the neutron reaction, because its concentration was proportional to the activities of ¹⁵²Eu and ⁶⁰Co. The surface dose rates inside the accelerator room were also monitored to define the decontamination area. The surface dose rate was proportional to the residual radioactivity, such as ⁶⁰Co. A careful evaluation was very useful in order to minimize the radioactive waste during decontamination.     

Uranium and Plutonium Extraction by N,N-dialkylamides Using Multistage Mixer-settler Extractors

N,N-Dialkylamides (monoamides) are known as extractants for U and Pu, and many studies have been carried out mainly by single-stage batch method. We have focused on two monoamides: N,N-di(2-ethylhexyl)-2,2-dimethylpropanamide (DEHDMPA) and N,N-di(2-ethylhexyl)butanamide (DEHBA), and proposed a multistage extraction process for recovering U and Pu by these monoamides. A continuous counter-current experiment was carried out to demonstrate the validity of this process. This process consisted of two cycles, and the 1st cycle and the 2nd cycle employed DEHDMPA and DEHBA as extractants, respectively. The feed solution for the 1st cycle was 5.1 mol/dm³ (M) nitric acid containing 0.92 M U, 1.6 mM Pu, and 0.6 mM Np. The raffinate collected in the 1st cycle was used as the feed for the 2nd cycle. The ratios of U recovered in the U fraction and U-Pu fraction were 99.1% and 0.8%, respectively, and the ratios of U in the used solvents were <0.04%. The ratio of Pu recovered in the U-Pu fraction was 99.7%, and the ratio of Pu in the used solvents was in the order of 10^–3–10^–4%. The concentration ratio of U with respect to Pu in the U-Pu fraction was 9, and this indicated that Pu was not isolated. The decontamination factor of U with respect to Pu in the U fraction was obtained as 4.5×10⁵. These results supported the validity of the proposed process.     

Accidental and retrospective dosimetry using TL method

Retrospective dosimetry is one of the most important tools of accidental dosimetry for dose estimation when dose measurement was not planned. In the affected area many objects can be applied as natural dosimeters. The paper discusses our recent investigations on various electronic components and common salt (NaCl) having useful thermoluminescence (TL) properties. Among materials investigated the electronic components of cell phones seem promising for retrospective dosimetry purposes, having high TL responses, proper glow curve peaks and the intensity of TL peaks vs. gamma dose received provided nearly linear response in the dose range of 10 mGy–1.5 Gy.     

Selective Pressurized Liquid Extraction of PCB’s from Food and Feed Samples: Effects of High Lipid Amounts and Lipid Type on Fat Retention

Fat free extraction of polychlorinated biphenyls (PCBs) from fat containing food and feed matrices was achieved by selective pressurized liquid extraction using sulphuric acid impregnated silica inside 100 mL extraction cells on a Dionex ASE300. Data were compared to previous publications where extractions had been performed on a Dionex ASE200, with 33 mL cells and a Dionex ASE300, with 34 mL. In all extractions a high lipid amount of 1,500–3,000 mg was used in the extractions. Seven different fat/fat retainer ratios (FFRs) were tested (0.200, 0.150, 0.100, 0.075, 0.050, 0.040 and 0.025) at 100 and 150 °C using n-heptane as extraction solvent. The FFR ratio differed between triglycerides and fish oil in that fat free extracts were obtained at FFR of 0.050 for fish oil at 150 °C but 0.040 for fish triglycerides. When the extraction temperature was lowered to 100 °C a FFR ratio of 0.050 resulted in fat free extracts for both matrices. These data differ from previous studies, on ASE200 33 mL cells and ASE300 34 mL cells, were both matrices required a FFR of 0.025. The influence on the PCB recovery of these higher amounts of lipids in the extraction cells was tested by spiking triglycerides and fish oil with PCBs and extracting them with FFR-values of 0.025, 0.040 and 0.050. This showed that there was no difference in the PCB recovery and thus allowing a higher amount of lipids in each extraction cell when a FFR ratio of 0.050 could be used. The method was also tested on naturally contaminated cod liver homogenate, naturally contaminated cod liver oil spiked to feed for poultry, as well as certified reference materials (Cod liver oil BCR 349 and Spiked pork fat IRMM 445).     

Nitrogen and phosphorus co-doped carbocatalyst for efficient organic pollutant removal through persulfate-based advanced oxidation processes

Carbocatalysts doped with heteroatoms such as nitrogen or sulphur have been reported to be useful in persulfate-based advanced oxidation processes for organic pollutant removal. However, there is limited research on the effect of doping with phosphorus atoms on degradation performance. In this work, a new nitrogen and phosphorus-doped carbocatalyst (N, P-HC) was designed using hydrothermal carbonization followed by pyrolysis at 700 °C, with olive pomace as a carbon source, to degrade organic pollutants in the presence of peroxydisulfate (PDS). Experimental results showed that N, P-HC, with its large specific surface area (871.73 m².g⁻¹), high content of N-pyridinic and N-pyrrolic groups, and the presence of P-O-C and O-P-C bonds, exhibited high degradation performance (98% degradation of Rhodamine B (RhB) in 40 min, with an apparent rate constant (k_app) of 0.055 min⁻¹ and an excellent turnover frequency (TOF) of 0.275 min⁻¹). Quenching study and EPR analysis revealed that singlet oxygen generation (¹O₂) and direct electron transfer were the main reaction pathways for the non-radical pathway in the degradation of RhB. The improved catalytic efficiency in the N, P-HC/PDS/RhB system can be attributed to the synergistic effect between N and P atoms in the graphitic structure of the carbocatalyst, its high surface area, and the presence of oxygenated functional groups on the surface of the N, P-HC. The used N, P-HC carbocatalyst can also be efficiently recovered by heat treatment at 500 °C. Overall, this study presents a simple and environmentally friendly method for synthesizing a high-performance N, P co-doped olive pomace-based carbocatalyst for water decontamination through PS-AOPs processes.     

Use of isooctyl thioglycolate for the separation of tin and antimony

The extraction characteristics of isooctyl thioglycolate (IOTG), a chelating agent, in various diluents has been studied with respect to the metal ions, tin(IV) and antimony(III), in hydrochloric acid medium. It is concluded that antimony(III) can be separated from tin(IV) with 85% yield and with a decontamination factor of at least 1·10⁵ using IOTG diluted with petroleum ether and 3M HCl medium. Tin(IV) can be separated conveniently from antimony(III) in 2M HCl with 95% yield and with a decontamination factor greater than 7·10⁵ using IOTG diluted with carbon tetrachloride.     

Assessment of radon concentration and external gamma radiation level in the environs of Narwapahar uranium mine,India and its radiological significance

In the environs of uranium mining, milling and processing facilities and in the uranium mineralized terrain, a little higher ambient radon concentration and gamma radiation level may be expected in comparison with natural background. The present study gives a brief account of atmospheric radon concentration, gamma absorbed dose rate and radiation dose received by the members of public in the vicinity of Narwapahar uranium mine. The ambient radon concentration in the air in the study area was found to vary from 5 to 107 Bq m⁻³ with geometric mean of 24 Bq m⁻³ and geometric standard deviation of 1.74 Bq m⁻³. The measured gamma absorbed dose rate in air at 1 m above the ground ranged from 87 to 220 nGy h⁻¹ with an overall arithmetic mean of 128 ± 18.5 nGy h⁻¹. The mean annual effective dose received by the members of public from inhalation of radon and its progeny and external gamma exposure was estimated to be 0.32 mSv year⁻¹, which is comparable to other reported values elsewhere.     

Effect of gamma irradiation on microbial decontamination,and chemical and sensory characteristic of lycium fruit

Lycium fruit, popular traditional Chinese medicine and food supplement generally is ingested uncooked, was exposed to several doses of gamma irradiation (0–14 kGy) to evaluate decontamination efficiency, changes in chemical composition, and changes in sensory characteristic. In this study, lycium fruit specimens contained microbial counts of 3.1×10³–1.7×10⁵ CFU/g and 14 kGy was sufficient for microbial decontamination. Before irradiation, the main microbe isolated from lycium fruit was identified as a strain of yeast, Cryptococcus laurentii. After 10 kGy of irradiation, a Gram-positive spore-forming bacterium, Bacillus cereus, was the only survivor. The first 90% reduction (LD₉₀) of C. laurentii and B. cereus was approximately 0.6 and 6.5 kGy, respectively, the D₁₀ doses of C. laurentii and B. cereus was approximately 0.6 and 1.7 kGy, respectively. After 14 kGy irradiation, except the vitamin C content, other chemical composition (e.g., crude protein, β-carotene, riboflavin, fructose, etc.) and the sensory characteristic of lycium fruit specimens did not have significant changes. In conclusion, 14 kGy is the optimal decontamination dose for lycium fruit for retention of its sensory quality and extension of shelf life.     

Microbial quality evaluation and effective decontamination of nutraceutically valued lotus seeds by electron beams and gamma irradiation

Lotus seeds are nutraceutically valued natural plant produce, which succumbs to microbial contamination, predominantly to toxigenic moulds. Results of the present study revealed seed coat portion to harbor higher proportion of microbial load, particularly fungi than cotyledon portion. Among the mycotoxins analyzed, aflatoxins (B₁, B₂, G₁ and G₂) were below detectable limits, while the seeds were devoid of Ochratoxin-A (OTA). Application of different doses of electron beam and gamma irradiation (0, 2.5, 5, 7.5, 10, 15 and 30 kGy) for decontamination purpose revealed significant dose-dependent decrease in the fungal contaminants (P<0.05). However, the contaminant yeasts could survive up to 10 kGy dose, which could be completely eliminated at 15 kGy. From the results obtained, a dose range between 10 and 15 kGy is recommended for complete decontamination, as these doses have also been shown earlier to have minimal effects on nutritional and functional properties of lotus seeds.     

Selective pressurized liquid extraction of polychlorinated biphenyls from fat-containing food and feed samples influence of cell dimensions, solvent type, temperature and flush volume

Sulphuric acid impregnated silica was used for the lipid free extraction of polychlorinated biphenyls from fat containing food and feed matrices using pressurized liquid extraction on a Dionex ASE300, with 34 mL cells. Data were compared to a previous publication where extractions had been performed on a Dionex ASE200, with 33 mL cells. Four different fat/fat retainer ratios (FFRs) were tested (0.100, 0.075, 0.050 and 0.025) at 50 and 100 degrees C using n-pentane, n-hexane or n-heptane as extraction solvent. The best results were obtained with a FFR of 0.025 when applying a temperature of 100 degrees C. Both n-pentane and n-heptane were capable of replacing n-hexane as extraction solvent. A flush volume of 60% was sufficient as suggested in US Environmental Protection Agency Method 3545. The applicability of the method was demonstrated for naturally contaminated fish meal as well as various spiked and certified materials.     

A suite of sensitive chemical methods to determine the δ15N of ammonium, nitrate and total dissolved N in soil extracts

Natural ¹⁵N abundances (δ¹⁵N values) of different soil nitrogen pools deliver crucial information on the soil N cycle for the analysis of biogeochemical processes. Here we report on a complete suite of methods for sensitive δ¹⁵N analysis in soil extracts. A combined chemical reaction of vanadium(III) chloride (VCl₃) and sodium azide under acidic conditions is used to convert nitrate into N₂O, which is subsequently analyzed by purge‐and‐trap isotope ratio mass spectrometry (PTIRMS) with a cryo‐focusing unit. Coupled with preparation steps (microdiffusion for collection of ammonium, alkaline persulfate oxidation to convert total dissolved N (TDN) or ammonium into nitrate) this allows the determination of the δ¹⁵N values of nitrate, ammonium and total dissolved N (dissolved organic N, microbial biomass N) in soil extracts with the same basic protocol. The limits of quantification for δ¹⁵N analysis with a precision of 0.5‰ were 12.4 µM for ammonium, 23.7 µM for TDN, 16.5 µM for nitrate and 22.7 µM for nitrite. Copyright © 2010 John Wiley & Sons, Ltd.     

Phosphathiahelicenes: Synthesis and Uses in Enantioselective Gold Catalysis

Enantiomerically pure thiahelicenes displaying a terminal phosphole unit and a stereogenic phosphorus center have been prepared by oxidative photocyclization of a diaryl‐olefin precursor. Starting from one of these phosphathiahelicene oxides, the corresponding trivalent phosphine–Au^I complex is obtained with complete diastereoselectivity. It affords a new, excellent precatalyst for the enantioselective cycloisomerization of N‐tethered enynes (up to 96 % ee).     

Paradigms and paradoxes: the conformation of the fundamental unit of hyaluronic acid

The geometries of the basic dimers of hyaluronan and chondroitin were compared by quantum chemical calculations. As is known the two systems differ in the relative orientation of one hydroxyl group. The basic unit of hyaluronan in its lowest-energy structure is some 20 kJ mol⁻¹ lower in energy than the lowest-energy chondroitin unit. However, the interconversion between the two systems is prevented by a very high energy barrier. The introduction of aqueous medium somewhat changes the relative stabilities of various structures within the hyaluronan sets and chondroitin sets, respectively, but does not change the energy preference of hyaluronan over chondroitin though somewhat diminishes it.     

Develop dissipative particle dynamics method to study the fluid flow and heat transfer of Ar and O2 flows in the micro- and nanochannels with precise atomic arrangement versus molecular dynamics approach

Fluid atomic behavior is an important factor for industrial applications. Computer simulations based on simple models predict Poiseuille flow for these atomic structures with the presence of external force. In this work, we describe the dynamical properties of Ar and O₂ flows with precise atomic arrangement via dissipative particle dynamics (DPD) and molecular dynamics (MD) simulation approaches. In these methods, each model is represented by using Large-scale Atomic/Molecular Massively Parallel Simulator package. Simulation results show that maximum rate for velocity of Ar flow in platinum and copper microchannels is 0.100 (unit less)/0.091 Å ps^?1 and 0.121 (unit less)/0.105 Å ps^?1 by using DPD/MD approach. This atomic parameter changes to 0.111 (unit less)/0.102 Å ps^?1 and 0.125 (unit less)/0.108 Å ps^?1 for O₂ fluid with mentioned approaches. By decreasing the microchannel size, the maximum rate of velocity reaches to 0.101 (unit less)/0.099 Å ps^?1 and maximum temperature rate decreases to 485 (unit less)/440 K with DPD/MD approaches. These calculated parameters can be used in industrial application designing for some processes such as heat transfer in structures. It was seen that the developed DPD approach was able to simulate the fluid flow and heat transfer of various types of fluids at micro- and nanoscales with suitable accuracy versus MD.

     

Quantification of radiation dose from short-lived positron emitters formed in human tissue under proton therapy conditions

The dose distribution in proton therapy is mainly due to primary particles and secondary electrons. The contribution of short-lived β⁺ emitters formed in the interactions of protons with the light mass elements C, N and O has hitherto not been considered. We estimated the formation of ¹¹C, ¹³N and ¹⁵O in irradiation of tissue with 200 MeV protons. The integral yields at 150 MeV were compared with a literature phantom measurement. The results for ¹¹C and ¹⁵O agreed very well; for ¹³N, however, appreciable deviation was observed. The activities were also calculated in the region around the Bragg peak as well as over the path length after entrance of the beam. Dose calculations were then done using the medical internal radiation dose (MIRD) formalism. Furthermore, a dose calculation was simulated for a 150 MeV proton beam (2 nA, 2 min) in a brain tumour. The dose deposited by the positron emitters in the Bragg peak region was found to be about 1.5 mGy, i.e. less than 1% of the dose estimated from the electronic interactions of protons. The absorbed dose in the whole brain amounted to 5.5 mGy.     

Reversed phase chromatographic separation of zirconium,niobium and hafnium tracers with HDEHP

Effective separation of the congeneric pair of elements, zirconium and hafnium and also niobium which was in admixtures with zirconium as daughter in its isotopic form were achieved through reversed phase column and paper extraction chromatographic procedures using di-(2-ethylhexyl)phosphoric acid (HDEHP) as the liquid exchanger. In reversed phase column chromatographic separation, the tracers,⁹⁵Zr,⁹⁵Nb and^175,181Hf, were extracted by HDEHP impregnated on kieselguhr and were sequentially eluted with 6N H₂SO₄+xN oxalic acid+H₂O₂(where x=0.1, 0.5 and 2). Similarly, in reversed phase paper chromatographic study in which a coating of HDEHP on Whatman No. 1 chromatographic paper was used as stationary phase, the mobile phase, 18N H₂SO₄+0.1N oxalic acid + H₂O₂, helped in separating the elements with favorable separation factors. Under the optimal conditions, the separation and decontamination of the elements in both methods were found to be quantitative, as verified by -spectrometric studies.     

Radiochemical neutron activation analysis of traces of vanadium in biological samples: A comparison of prior dry ashing with post-irradiation wet ashing

Summary A radiochemical neutron activation technique for nanogram and subnanogram levels of vanadium in biological samples was developed, based on dry ashing of the sample prior to irradiation, but without any chemical treatment. It was compared to and validated by parallel analyses of low-level reference materials and human blood using a previously developed totally post-irradiation technique based on rapid wet ashing of the irradiated sample. The irradiated ash was also wet ashed after neutron bombardment to ensure complete dissolution, equilibration with carrier and removal of ³⁸Cl. Results for reference materials, including Versieck's Second Generation Human Serum Reference Material and IAEA Animal Blood, were in excellent agreement by the two techniques, and with reference to literature values. Both methods give exceptionally good radiochemical decontamination of ⁵²V from other nuclides and have nearly quantitative yields. The dry ash mode is slightly quicker and easier to manipulate.     

Radiation grafting of N,N′-dimethylacrylamide and 2-hydroxyethylmethacrylate onto polypropylene films by one step method

The work presented herein reports on polypropylene films grafted with N,N′-dimethylacrylamide and 2-hydroxyethylmethacrylate. The grafted films were obtained by an oxidative pre-irradiation method in one step using a gamma source of ⁶⁰Co. The optimal conditions such as reaction time, monomer concentrations and radiation doses were investigated. Characterization of the grafted polymers was carried out through FTIR-ATR, TGA, DSC, and swelling. Grafts onto polymeric films between 10 and 850% were obtained at doses from 20 to 150 kGy and a dose rate of 8.3 kGy/h.     

Radiation induced degradation of pharmaceutical residues in water: Chloramphenicol

The γ-radiolytic degradation of chloramphenicol (CPL) was investigated in 0.1–1 mmol dm^?3 aqueous solutions at various radiation conditions. The destruction of CPL was monitored by UV–vis spectrophotometric method through the decrease in the intensity of the absorbance band at 276 nm. LC-MS/MS was used to identify the degradation products. Results indicate that ^?OH can add onto the CPL aromatic ring or can abstract H-atom from the side chain. The reductive dechlorination of CPL was also studied based on the reaction of e_aq^? with CPL. In 0.1 mmol dm^?3 solution above 2.5 kGy dose complete CPL degradation was achieved. In the presence of dissolved oxygen at relatively low dose, various oxidation products were observed. In the presence of tertiary butanol radical scavenger tertiary butanol group containing products were also detected. The toxicity increased as a function of dose to 1.0 kGy. At doses higher than 1.0 kGy the toxicity decreased continuously due to further degradation. It was also demonstrated that the O₂^??/HO₂^? pair has low reactivity in CPL solution.     

Effects of acidic peptide size and sequence on trivalent praseodymium adduction and electron transfer dissociation mass spectrometry

Using the lanthanide ion praseodymium, Pr(III), metallated ion formation and electron transfer dissociation (ETD) were studied for 25 biological and model acidic peptides. For chain lengths of seven or more residues, even highly acidic peptides that can be difficult to protonate by electrospray ionization will metallate and undergo abundant ETD fragmentation. Peptides composed of predominantly acidic residues form only the deprotonated ion, [M + Pr ‐ H]²⁺; this ion yields near complete ETD sequence coverage for larger peptides. Peptides with a mixture of acidic and neutral residues generate [M + Pr]³⁺, which cleaves between every residue for many peptides. Acidic peptides that contain at least one residue with a basic side chain also produce the protonated ion, [M + Pr + H]⁴⁺; this ion undergoes the most extensive sequence coverage by ETD. Primarily metallated and non‐metallated c‐ and z‐ions form for all peptides investigated. Metal adducted product ions are only present when at least half of the peptide sequence can be incorporated into the ion; this suggests that the metal ion simultaneously attaches to more than one acidic site. The only site consistently lacking dissociation is at the N‐terminal side of a proline residue. Increasing peptide chain length generates more backbone cleavage for metal‐peptide complexes with the same charge state. For acidic peptides with the same length, increasing the precursor ion charge state from 2+ to 3+ also leads to more cleavage. The results of this study indicate that highly acidic peptides can be sequenced by ETD of complexes formed with Pr(III). Copyright © 2017 John Wiley & Sons, Ltd.