SAXS investigation on the influence of oil dilution on morphological changes in a SBS block copolymer during the first draw cycle

Spin-cast films of one pure SBS and two oil-extended SBS samples were observed during first cycle drawing in the synchrotron radiation beam at Hasylab. For evaluation, from a two-dimensional Vidicon scattering picture the scattering curve was extracted by intersecting perpendicular to the observed layer lines. Using a method described in a preceding paper [1], the scattering curve is analyzed by fitting to one-dimensional two-phase models. Essential for a fit with parameters of physical sense is the assumption of at least two components. One of these two main components is identified with fibrils containing PS cylinders, the axes of which are orientated parallel; the other is identified with fibrils containing cylinders transverse to the drawing direction.For the mechanical properties of the thermoplastic rubber this splitting of cylinder orientation in the drawn state seems to be of some importance. Only the cylinders of the longitudinal component turn out to be rigid, while the cylinders of the transversal component appear to yield and even break.The amount of cylinders allotted to each of the two components in the drawn state varies as a function of the diluent. An extrapolation of topological parameters back to the undrawn state indicates a possible reason, a fair variation of the cylindrical particle dimensions within a lattice cell of only slighly varying dimensions. While paraffinic mineral oil dilution causes the cylinders lengths to decrease, thus improving cylinder orientability within the pseudo lattice cell, aromatic oil dilution increases the particles diameters.A remaining faint contribution to the scattering pattern that produces the layer lines is suggested not to be caused by a periodic structure, but by a single and precisely defined polybutadiene matrix length (string) between two PS cylinders with a considerable height variance.     

Gas permeability of block copolymers of styrene and butadiene

The permeability of styrene-butadiene block copolymer foils with different composition prepared by casting and pressing has been investigated for the gases Ar, CO₂, and CH₄ at pressure difference of 400 mbar and at the temperature range 298 T [K] 333.The permeation process can be described by the solution diffusion mechanism. The diffusion coefficients decrease in the sequence of the gases Ar, CO₂, and CH₄ and the solubility coefficients increase in the sequence Ar, CH₄, CO₂.The dependence of the permeability on the composition of the block copolymer can be interpreted by the help of percolation theory and the effective medium theory. It follows the critical volume fraction of the percolation of the transport phase _PB ^c (= 0,23) and the coordination numberz (= 4) giving an information concerning the multiphase structure of the block copolymer.Presented in part at the 33^rd Annual Meeting of the Colloid-Gesellschaft, Graz, Austria, September 14–16, 1987.     

Craze fibril extension ratio measurements in glassy block copolymers

The extension ratios of crazes in triblock copolymer films of poly(2-vinylpyridine)-polystyrene-poly(2-vinylpyridine) [PVP-PS-PVP] which had lamellar microphase domain structure were measured by transmission electron microscopy. The extension ratio when the lamellae were oriented parallel to the craze fibril direction was always greater than that when the lamellae were oriented perpendicular to this direction, reflecting the stretching of the chains of the block copolymer in a direction normal to the interfaces of the lamellar domains.     

Geometrical constraints on microstructural development in block copolymer ultrathin films

The fact that microstructures form in microphase-separated block copolymers, endowing the materials with unique thermo-mechanical properties, is well-established. However, no thermodynamic theories directly address the problem of microstructural development in ultrathin films, which might be useful as adhesives or resists. To predict the microstructural dimensions in such films, a model based on unit-cell geometries and material/volume balances is developed. Predictions of the ratio of the characteristic length of the domain core to domain repeat distance are obtained for poly (styrene-butadiene) diblock (SB) copolymers at 298 K. The finite interphase region is included in the volume balances with the parameterf, the volume fraction of interphase material, obtained from a modified version of the Leary-Henderson-Williams thermodynamic theory and shown here not to be a strong function of composition. An approach, implementingf, for accurately estimating the critical molecular weight of microphase separation in the strong-segregation limit (M _c ), as a function of bulk composition for monodisperse SB copolymers at 298 K, is also presented.     

Interface stabilization and micelle formation in blends with a block copolymer

The phase separation behavior of ternary blends of two homopolymers, PMMA and PS, and a block copolymer of styrene and methylmethacrylate, P(S-b-MMA), was studied. The homopolymers were of equal chain length and were kept at equal amounts. Two copolymers were used with blocks of equal length, which exceeded or equaled that of the homopolymer chains. Varied was the copolymer contentf. Films were cast from toluene, which is a nonselective solvent. The morphologies of the cast films were compared with the structure of the critical fluctuations in solution, which were calculated in mean field approximation. The axis of blend compositionsf can be divided into parts of dominating macrophase and microphase separation. Above a transition concentrationf _o, all copolymer chains are found in phase interfaces. Belowf _o, part of them form micelles within the homopolymer phases.     

Determination of the structure factor for concentrated silica dispersions using small angle x-ray scattering I. Simulation

The structure factor of a concentrated colloidal suspension is an important means in the characterization of the interaction forces between the colloidal particles. It can, in principle, be determined with small angle x-ray scattering. To avoid unacceptably long measuring times, one has to use a high power x-ray source or a slit collimation camera. The first is not readily accessible because of the very high costs. The latter is available in many laboratories, but here the fundamental information is contained in the data in a complicated way. A so-called desmearing operation is needed to reveal this information. Because of the different experimental errors and their sensitivity to the desmearing, the accuracy of the structure factor will be rather limited. In this paper we simulate the experimental errors separately to check their influence in combination with the desmearing.Although the overall accuracy is limited some important features can be determined. The value atK=0 and thus the osmotic compressibility can be calculated, and the position and the height of the first maximum in the structure factor are quite reliable too. This gives some insight in the type of interaction and the influence of polydispersity.Special attention should be given to the determination of the form factor by using extra long measuring times for the very diluted sample, this will improve the overall accurary.     

Enthalpy relaxations in polymer blends and block copolymers: Influence of domain size

It is now well known that enthalpy relaxation measurements can be used to establish polymer-polymer blend phase behavior when the glass transition temperatures of the two polymers are virtually coincident. In the most simple cases, the aging kinetics of an immiscible blend will be representative of the pure polymers superimposed upon each other. However, in many cases the situation is more complicated because of the presence of interface material. In this paper the relation between enthalpy recovery peak separation, domain size and interface thickness is considered. The discussion is based on relaxation experiments involving di-block copolymers of styrene and 2-vinyl pyridine, blends of polystyrene and poly(2-vinyl pyridine) and blends of poly(vinyl chloride) and poly(isopropyl methacrylate). If the amount of material in the interface is too large due to either a small average domain size or a thick interface no peak separation will occur. The first situation is found for the microphase separated block copolymer system whereas the second possibility occurs for blends of polymers which are on the verge of miscibility like poly(vinyl chloride) and poly(isopropyl methacrylate).Presented in part at the Sixth International Seminar on Polymer Physics Relaxation in Polymers, Gomadingen, October 3–8, 1988, F.R.G.     

Small angle X-ray scattering study of an extremely elongated micelle system of CTAB-p-toluidine solution

Whenp-toluidine is added to an aqueous solution of CTAB, a remarkable increase of viscosity is accompanied by a spectacular elasticity. We detected the existence of extremely elongated rod-like micelles in electron micrographs. SAXS measurements indicate a closely packed array of cylindrical rod-like micelles, brought about when solutions flow through a thin capillary. A scattering maximum ofd=160 Å almost corresponds to the distance between the nearest neighbours of the cylindrical rod-like micelles. This value agrees with the diameter measured on electron micrographs. The second broad peak (d=75 Å) is assigned to a subsidiary maximum of the shape function of the cylinder with infinite length.     

Crystallization of microphase-separated block copolymers with two crystallizing blocks

Statistical poly block copolymers of polyamide with polyethyleneoxide are investigated. The regularities governing the formation of their phase structure depending on the composition, temperature, and prehistory of the system are established. The character of crystallization of both blocks is shown to be due to their mutual solubility in the melt. Some peculiarities of microphase crystallization in PA/PEO block copolymers are revealed. It is found that, depending on the character of phase separation in the system, a PEO block may be crystallized either unimodally or in two well-separated temperature ranges.Dedicated to Prof. W. Pechhold on the occasion of his 60th birthday.     

Characteristic changes of pH during the alkalization of latex dispersions of the ethyl acrylate — methacrylic acid copolymers

The titration curves of latex dispersions of ethyl acrylate — methacrylic acid copolymers have a rather complex shape which indicates a strong dependence of the apparent dissociation constant of carboxylic groups on the degree of neutralization and copolymer composition. These dependences seem to be related to changes in the macroscopic structure (swelling and disintegration) of dispersion particles during alkalization.     

Small-angle neutron scattering on shear-induced micellar structures

Small-angle neutron scattering (SANS) experiments on sheared aqueous surfactant solutions of tetradecyltrimethylammoniumsalicylate (TTMA-Sal) are reported. A5-mM-solution without shear shows a weak correlation peak at a momentum transfer of 0.09 nm^–1 which has its origin in the micellar interaction. For shear rates above a threshold value of =40 s^–1 the scattering pattern shows an irregular increase in anisotropy. The analysis of the anisotropic pattern reveals the existence of two types of micelles: Small rodlike micelles which are weakly aligned and very large rodlike aggregates which are strongly aligned and which are present above the threshold value of. The two micelles are in equilibrium with each other and the equilibrium shifts with increasing shear rate to the side of the large oriented micelles.     

An evaluation method for SAXS-patterns of fibrillar two-phase systems containing oriented particles of moderate anisotropy and short range correlation

Starting from the theoretical background of Rulands interface distributions, an evaluation method for small angle x-ray patterns arising from oriented fibrillar two-phase structures is proposed. If the fibril contains highly oriented particles with only moderate anisotropy and if the correlations between those particles within the fibril are of short range only, every axial section of the scattering pattern shows a one dimensional Porod law. A procedure of successive model confinement using the well known tools of nonlinear regression analysis is described. The result of such an analysis for the scattering pattern of an oil diluted SBS block copolymer recorded with synchrotron radiation under first-cycle stretching is reported. At=4 nm four contributions to the scattering pattern could be identified: a) fibrils containing well-defined cylinders standing upright; b) fibrils containing lying cylinders under destruction; c) stretched-out polybutadiene chains, connecting two polystyrene cylinders and causing the observable layer line pattern; and d) stretched-out polybutadiene chains looping through the neighboring PS domain and returning to their starting domain. In addition, a simple method for determining the height-to-diameter ratio of cylinders from the form factor envelope is proposed.     

Spherical shape instability induced changes in the structure of microemulsions

The dispersed phase of a microemulsion in equilibrium with the excess dispersed phase is in the form of spherical globules. A change in the structure of the microemulsion near the transition from two to three phases is predicted on the basis of thermodynamic considerations. This change occurs because the spherical interface of the globules becomes unstable to perturbations. Because this instability is a result of the condition of equilibrium itself, there is a similarity (but not identity) to the behavior near a critical point. The spherical interface can also become unstable to perturbations in some single-phase microemulsions, although it is stable in microemulsions that coexist with the excess dispersed phase. Thermodynamic considerations also indicate that at the transition from two to three phases, the curvature of the spherical globules must be zero. This result is extended to the entire middle-phase microemulsion as the condition of zero mean-time or space-average curvature. Such a condition can be satisfied in the neighborhood of the transition points from two to three phases and again from three to two phases via the oscillations of the globular interface; in the central region of the middle phase, where the volume fraction of oil0.5, this condition is likely to be satisfied via the oscillations of the interface of a bicontinuous sponge.     

Spinodal decomposition of the polymer blend deutereous polystyrene (d-PS) and polyvinylmethylether (PVME) studied with high resolution neutron small angle scattering

Decomposition of a polymer blend in the miscibility gap has been studied by small angle scattering of neutrons, using a double crystal diffractometer. It covers a range of 10^–5 to 10^–3 Å^–1, which connects the region of elastic light scattering and, at the upper end, the region of conventional neutron small angle scattering instruments. The decomposed structure in the miscibility gap can be described by a characteristic lengthR which increases with time,t ^1/3 between 7 and 25 min. At longer times, the growth follows a more linear power law. This behaviour is consistent with predictions of the domain growth for liquid mixtures and is estimated by using the self diffusion constant, viscosity, and the surface energy of the polymer.on leave ESFM-IPN Mexico     

Poly(styrene-b-2-vinylpyridine-1-oxide) and poly(dimethyl-siloxane-b-2-vinylpyridine-1-oxide) diblock copolymers 2. Micellar solutions in water/propan-2-ol mixtures

Dynamic light scattering and viscometry measurements have been carried out on three AB diblock copolymers in water/propan-2-ol mixtures. The A moieties in each case were poly(2-vinylpyridine-1-oxide) for which both water and propan-2-ol are good solvents. The B Moieties were either polystyrene or polydimethylsiloxane, for which both water and propan-2-ol are poor solvents, but water is the worse solvent. In all cases, the hydrodynamic size of the micelles (assumed spherical) was found to increase with increasing water content in the solvent mixture; the aggregation number was also found to increase. The former finding is in agreement with the theoretical predictions of Munch and Gast, but not the latter.     

Small-angle x-ray scattering by crystalline polymer fibers 2. Investigation of the linear paracrystalline model using various materials

The linear position-sensitive detector is well-suited to measure quantitatively the distribution parallel to the fibre axis of the intensity of small-angle x-ray scattering (SAXS) by polymer fibres, except that in the case of four-point patterns their width is greater than that of the detector window. A method is described which overcomes this problem, and which has high angular resolution. Using this method, the variation of scattered intensity with angles from 0.3° to 2.5° has been measured for fibres of poly(ethylene terephthalate), nylon, and low density poly(ethylene) (LDPE), and compared with that predicted by the linear paracrystalline model. In all cases except LDPE, when the distribution of phase lengths was given by the Reinhold function, there was no significant disagreement between the measured and predicted scattering except for a very small range of angles on the low angle side of the peak intensity. With LDPE small but significant discrepancies were found at other angles as well, and these were worse if the symmetrical Gaussian distribution function was used. The method enabled quantitative parameters describing the morphology to be obtained. It is concluded that the morphology of the linear paracrystalline stack is consistent with the SAXS intensity distribution, and that the Reinhold function is a reasonable approximation to the distribution of phase lengths. A small modification so that this decays more rapidly at long lengths might be necessary to explain the scattering for all materials over the entire angular range and other small changes might be needed with LDPE, although the asymmetrical nature of the distribution must be retained.On leave from Department of Physics, University of Technology Malaysia, 81300 Sekudai, Malaysia.     

Viscoelastic properties of polyacrylonitrile particles stabilised by a poly-2-vinylpyridine/polytert butylstyrene block copolymer

The viscoelastic properties of a dispersion of polyacrylonitrile particles stabilised by a block copolymer poly-2-vinylpyridine/polytert butylstyrene dispersed in solvesso have been measured as a function of particle concentration and frequency at ambient temperatures. At low volume fraction of particles it was found that the loss modulus of the dispersions was larger than the storage modulus, whilst at volume fractions > 0.40 the storage modulus dominates the rheology. This is attributable to there being a steric repulsion between the particles as a result of an increasing concentration of particles and the resultant reduction in interparticle separation in the dispersion. In addition the observed exponential increase of the storage modulus with increasing particle volume fraction mirrors the exponential increase in force with decreasing surface separation of the same type of polymers adsorbed to mica.     

Thermo-optical analysis as a complementary method in the study of phase transitions of thermotropic liquid crystalline polymer and its blends with polycarbonate

Differential scanning calorimetry (DSC) and thermo-optical analysis (TOA) were applied to study the phase transitions phenomena of thermotropic liquid crystalline polymer and its blends with polycarbonate. It was found that both methods are complementary. Glass transition temperatures of the blends of polycarbonate with liquid crystalline polymer were measured and discussed.     

Structural changes in solvent-induced crystallization of quenched isotactic polypropylene

Solvent-induced crystallization of quenched isotactic polypropylene (iPP) films in dichloromethane, cyclohexane, carbon tetrachloride, and chloroform has been investigated.WAXD, density, and DSC measurements indicate that smectic iPP films undergo a complex rearrangement of the structure in these liquids, leading to a process of crystallization.Transport properties of the dried samples, after the solvent treatment, show that the first stage of crystallization involves, in addition to the smectic phase, a fraction of amorphous phase, while further crystallization regards only the smectic phase.The morphology of the crystallized samples has been investigated by transmission electron microscopy following permanganic etching. No change in the basic morphology is found, although local organization showing splaying and branching appears clearer in the solvent crystallized samples than in the starting smectic sample.     

Shear-induced deformation of polystyrene coils in dilute solution from small angle neutron scattering 2. Variation of shear gradient,molecular mass and solvent viscosity

The technique of small angle neutron scattering (SANS) has been used to study the conformation of polystyrene chains in dilute solution under a constant shear gradient. The experiments reveal a distinct anisotropy of the molecular dimensions with regard to the directions parallel and perpendicular to the flow direction on the 2D-multidetector. The deformation ratio of the single polymer chain (R ²/R _iso ² )–1 as a function of the reduced shear gradient=([] · · M _w G)/RT shows a transition from the ideal ²-behaviour for dynamic infinitely flexible coils found at small gradients, to a behaviour with smaller increase at larger. These results are qualitatively consistent with the theory of Cerf for a polymer with finite internal viscosity in a shear gradient. At low(<1), a better agreement with the model of a free-draining coil (Rouse behaviour) than with the Zimm model is observed.