Reticular Sn nanoparticle-dispersed PAN-based carbon nanofibers for anode material in rechargeable lithium-ion batteries

Reticular tin nanoparticle-dispersed carbon (Sn/C) nanofibers were fabricated by stabilization of electrospun SnCl₄/PAN composite fibers and subsequent carbonization at different temperatures. These Sn/C composite nanofibers used as anode materials for rechargeable lithium-ion batteries (LIBs) show that the Sn/C nanofibers at 700 and 850 °C present much higher charge (785.8 and 811 mA h g^?1) and discharge (1211.7 and 993 mA h g^?1) capacities than those at 550 and 1000 °C and the as-received CNFs at 850 °C, corresponding to coulombic efficiencies of 64.9% and 81.7%, respectively. The superior electrochemical properties of the intriguing Sn/C nanofibers indicate a promising application in high performance Li-ion batteries.     

Cloud point extraction for determination of cadmium in soft drinks by thermospray flame furnace atomic absorption spectrometry

Cloud point extraction (CPE) is proposed as a preconcentration procedure for the determination of Cd in soft drinks by thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS). The cadmium reacted with pyridyl-azo-naphthol (PAN) to form hydrophobic chelates, which were extracted into the micelles of Triton X-114 in a solution buffered at pH 9. NaCl was used for the phase separation. The variables which affect the preconcentration were optimized using a 2³ factorial design and central composite design (CCD). A response surface maximum point was obtained, and the critical values were a concentration of 0.13 mmol L^? 1 PAN, 0.03% m/v Triton X-114 and 2.3% m/v NaCl. Under the optimized conditions, after the extraction and preconcentration steps, a sample volume of 100 μL was introduced into the hot Ni tube using water as the carrier at a flow rate of 0.4 mL min^? 1. The values obtained for the detection limit, relative standard deviation and preconcentration factor were 0.0178 μg L^? 1, 4.1% (n = 8) and 55.5, respectively. The accuracy of the proposed method was demonstrated by performing addition-recovery experiments. Recoveries varied from 88 to 104%.     

Fabrication of porous carbon/Si composite nanofibers as high-capacity battery electrodes

Carbon/Si composite nanofibers with porous structures are prepared by electrospinning and subsequent carbonization processes. It is found that these porous composite nanofibers can be used as anode materials for rechargeable lithium-ion batteries (LIBs) without adding any binding or conducting additive. The resultant anodes exhibit good electrochemical performance; for example, a large discharge capacity of 1100 mAh g^?1 at a high current density of 200 mA g^?1.     

Carbon-coated manganese dioxide nanoparticles and their enhanced electrochemical properties for zinc-ion battery applications

In this study, we report the cost-effective and simple synthesis of carbon-coated α-MnO_2nanoparticles(α-MnO_2@C) for use as cathodes of aqueous zinc-ion batteries(ZIBs) for the first time. α-MnO_2@C was prepared via a gel formation, using maleic acid(C_4H_4O_4) as the carbon source, followed by annealing at low temperature of 270 °C. A uniform carbon network among the α-MnO_2 nanoparticles was observed by transmission electron microscopy. When tested in a zinc cell, the α-MnO_2@C exhibited a high initial discharge capacity of 272 m Ah/g under 66 m A/g current density compared to 213 m Ah/g, at the same current density, displayed by the pristine sample. Further, α-MnO_2@C demonstrated superior cycleability compared to the pristine samples. This study may pave the way for the utilizing carbon-coated MnO_2 electrodes for aqueous ZIB applications and thereby contribute to realizing high performance eco-friendly batteries.     

Morphology and properties of hollow-fiber membrane made by PAN mixing with small amount of PVDF

In this paper, the morphological structure and properties such as, miscibility, tensile strength, flux and retention ratio of hollow-fiber membranes manufactured by PAN mixing with small amounts of PVDF have been studied. The hollow fiber was made from a spinning solution composed of polymer (PAN : PVDF=10 : 0, 9 : 1, 7 : 3), additive (PVP, PEG-600) and solvent (DMAC) when immersed in water. The spinnability of blend polymer and the influences of blending on spinning technology have been observed; the morphology of membranes were examined by SEM. The blend membranes possess much higher flux than PAN membrane and fairly good retention ratio especially for the membrane made by PAN : PVDF=9 : 1.     

Synthesis and properties of polyfluorene copolymers bearing thiophene and porphyrin

To search for more wider absorption and higher charge carriers mobilities materials of polymer solar cell, a series of soluble alternating polyfluorene copolymers were synthesized by palladium-catalyzed Suzuki coupling reaction. Their structures were determined by 1H NMR, IR and UV-vis. And their UV-vis absorption spectra indicated that they had strong absorption over 600 nm spectral range and nearly cover 400-700 nm visible region. The band gaps of copolymers calculated according to cyclic voltammetry （CV） were between 1.96 and 2.03 eV. Polymer：TiO2 bulk-heterojunction films were made from mixtures of polymer and titanium isopropoxide, a precursor for TiO2, via hydrolysis in air overnight. The photoluminescence at 380-800 nm of the blend film of PT-TPP20 （5 mg/mL）：Ti（OC3H7）4 （80 μL/mL） （20% volume fraction） was significantly quenched in the 50% Ti（OC3H7）4 blend film, indicating that rapid and efficient separation of photoinduced electron-hole pairs.     

Fabrication and magnetic properties of electrospun copper ferrite (CuFe2O4) nanofibers

Tetragonal copper ferrite (CuFe₂O₄) nanofibers were fabricated by electrospinning method using a solution that contained poly(vinyl pyrrolidone) (PVP) and Cu and Fe nitrates as alternative metal sources. The as-spun and calcined CuFe₂O₄/PVP composite samples were characterized by TG-DTA, X-ray diffraction, FT-IR, and SEM, respectively. After calcination of the as-spun CuFe₂O₄/PVP composite nanofibers (fiber size of 89 ± 12 nm in diameter) at 500 °C in air for 2 h, CuFe₂O₄ nanofibers of 66 ± 13 nm in diameter having well-developed tetragonal structure were successfully obtained. The crystal structure and morphology of the nanofibers were influenced by the calcination temperature. After calcination at 600 and 700 °C, the nature of nanofibers changed which was possibly due to the reorganization of the CuFe₂O₄ structure at high temperature, and a fiber structure of packed particles or crystallites was prominent. Crystallite size of the nanoparticles contained in nanofibers increases from 7.9 to 23.98 nm with increasing calcination temperature between 500 and 700 °C. Room temperature magnetization results showed a ferromagnetic behavior of the calcined CuFe₂O₄ samples, having their specific saturation magnetization (M_s) values of 17.73, 20.52, and 23.98 emu/g for the samples calcined at 500, 600, and 700 °C, respectively.     

Microstructure,magnetic properties and exchange–coupling interactions for one-dimensional hard/soft ferrite nanofibers

SrFe₁₂O₁₉ (SFO)/Ni_0.5Zn_0.5Fe₂O₄ (NZFO) composite ferrite nanofibers with diameters about 120 nm have been prepared by the electrospinning and calcination process. The SFO/NZFO composite ferrites are formed after calcined at 700 °C for 2 h and the composite nanofibers with various mass ratios obtained at 900 °C are fabricated from NZFO grains about 16–40 nm and SFO grains of 19–45 nm with a uniform phase distribution. With the SFO ferrite content increasing, the coercivity (H_c) and remanence (M_r) for the composite ferrite nanofibers initially increase, reaching maximum values of 379.8 kA/m (297 K) and 242.2 kA/m (77 K), 39.1 Am²/kg (297 K) and 53.5 Am²/kg (77 K), respectively, at a mass ratio (SFO:NZFO) of 4, and then show a reduction tendency with a further increase of the mass ratio. This enhancement in magnetic properties is attributed to the competition of the exchange–coupling interaction and the dipolar interaction in the composite nanofibers.     

A new triterpenoid saponin from the roots of Platycodon grandiflorum

A new triterpenoid saponin, 3-O-β-D-glucopyranosyl 16-oxo-platycodigenin 28-O-β-D-apiofuranosyl-(1→3)-β-D-xylopyranosyl-(1→4)-α-L-rhamnopyranosyl-(1→2)-α-L-arabinopyra-nosyl ester, was isolated from the roots of Platycodon grandiflorum, together with three known saponins, including platycodin D, deapio platycoside E and platycoside E. The structure of the new compound, named 16-oxo-platycodin D, was elucidated on the basis of spectroscopic data.     

Optical birefringence and molecular orientation of electrospun polycaprolactone fibers by polarizing-interference microscopy

The potential of polarizing-interference Pluta microscope for determination of optical birefringence of individual nanofibers formed by electrospinning was shown. This technique can be applied for measurements of fiber birefringence, practically at diameter above 300 nm. The molecular orientation of individual polycaprolactone (PCL) nanofibers was determined from birefringence assuming the same orientation of both phases, crystal and amorphous. The molecular orientation was determined using DSC crystallinity, crystal intrinsic birefringence calculated for the first time for PCL from bond polarizabilities as well as estimated value of amorphous intrinsic birefringence. Our results indicate that the birefringence and thus molecular orientation are strongly inhomogeneous along the nanofibers, reflecting a complex nature of forces acting during electrospinning process. The average molecular orientation is weak if any, being dependent together with fiber thickness and crystallinity on electrospinning parameters, like applied voltage, concentration and type of solvent. The obtained results indicate that the average molecular orientation displays similar dependence on applied voltage as fiber diameter. Relatively low melting temperature of electrospun nanofibers suggests low crystal size and/or high concentration of defects in crystals. This observation corresponds with low crystallinity and molecular orientation, indicating together relatively low degree of crystal ordering due to high rate of cooling and solvent evaporation during electrospinning, limiting thus crystallization process.     

Furostanol saponins with inhibitory action against COX-2 production from Tupistra chinensis rhizomes

Two furostanol saponins were obtained from the n-butanol fraction of methanol extract from Tupistra chinensis rhizomes,a folk medicine of Shennongjia Forest District of Hubei Province.Their structures were determined as (25S)-26-O-(β-D-glucopyranosyl)- furost-1β,3β,22α,26-tetrol-3-O-β-D-glucopyranosyl-(1→4)-β-D-glucopyranosyl-(1→2)-β-D-glucopyranoside (1) and (25R)- 26-O-(β-D-glucopyranosyl)-furost-1β,3β22α,26-tetrol 3-O-β-D-glucopyranosyl-(1→4)-β-D-glucopyranosyl-(1→2)-β-D-glu- copyranoside (2),on basis of chemical and spectroscopic evidences.1 and 2 displayed marked inhibitory action towards COX-2 production in macrophages of the rat abdomen induced by LPS at 20μg/mL.     

浸润性可调的导电聚苯胺/聚丙烯腈同轴纳米纤维

聚苯胺(PANI)因其具有可调的导电性、优异的化学稳定性、简单的制备方法等特点, 在化学电源、抗静电涂层、电磁屏蔽材料、抗腐蚀、传感器等领域具有广泛的应用前景[^1~4]. 由于聚苯胺的刚性分子链使得聚苯胺几乎不溶不熔, 难以加工应用, 因此, 将导电聚合物直接制成纳米纤维一直是合成纤维界所希望的目标之一. 此外, 由于材料尺度的减小, 使纳米材料的表面与界面性质,尤其是表面浸润性变得更为突出.浸润性是固体表面的重要特征之一, 它主要由表面的化学组成和微观结构共同决定^[5,6]. 可调的浸润性在超疏水材料、药物传输、仿生材料和微流体等领域具有重要的应用价值^[7~10] , 引起人们广泛关注.     

Partially reduced SnO2 nanoparticles anchored on carbon nanofibers for high performance sodium-ion batteries

One-dimensional (1-D) carbon nanofibers anchored with partially reduced SnO₂ nanoparticles (SnO₂/Sn@C) were successfully synthesized through a simple electrospinning method followed by carbon coating and thermal reduction processes. The partially reduced Sn frameworks, combined with the carbon fibers, provide a more favorable mechanism for sodiation/desodiation than SnO₂. As a result, SnO₂/Sn@C exhibits a high reversible capacity (536 mAh g^− 1 after 50 cycles) and an excellent rate capability (396 mAh g^− 1 even at 2 C rate) when evaluated as an anode material for sodium-ion batteries (SIBs).     

Synthesis of an antimetastatic tetrasaccharide β-D-Gal-(1→4)-β-d-GlcpNAc-(1→6)-α-D-Manp-(1→6)-β-D-Manp-OMe

An antimetastatic tetrasaccharide T₁,β-D-Gal-（1→4）-β-D-GlcpNAc-（1→6）-α-D-Manp-（1→6）-β-D-Manp-OMe,was synthesized with two approaches.The first approach was a conventional method employing thioglycoside and Koenigs-Knorr glycosylation reaction in 24%overall yield.The second one was a novel route through the azidoiodo-glycosylation strategy by using 2-iodo-2-deoxylactosyl azide as the donor in 36%overall yield.     

Hybrid magnetic amphiphilic composites based on carbon nanotube/nanofibers and layered silicates fragments as efficient adsorbent for ethynilestradiol

In this work, hybrid magnetic amphiphilic composites were prepared by the catalytic growth of carbon nanotubes (CNTs) and nanofibers CNF on layered silicates fragments. SEM, TEM, Raman, XRD, Mössbauer, TG/DTA showed that CVD with CH₄ at 800 °C produced CNF and magnetic Fe cores fixed on the surface of microfragments of silicates layers. Due to the amphiphilic character, the composites can be easily dispersed in water and efficiently adsorb hydrophobic contaminant molecules. For example, the composites showed remarkable adsorption capacities for the hormone ethinylestradiol, e.g. 2–4 mg m^?2, compared to ca. 0.1 mg m^?2 obtained for high surface area activated carbon and multiwall CNT. These results are discussed in terms of a high hydrophobic exposed surface area of the CNT and CNF fixed on the layered silicates fragments surface. Moreover, the composites can be easily removed from water by a simple magnetic separation process.     

A novel method for Co(Ⅱ) and Cu(Ⅱ) analysis by capillary electrophoresis with chemiluminescence detection

Based on the fact that some metal ions can catalyze the chemiluminescence(CL)reaction of luminol with K_3Fe(CN)_6,a novel capillary electrophoresis CL method was developed for the determination of Co(Ⅱ)and Cu(Ⅱ).The separation was carried out with a 10 mmol/L sodium acetate solution containing 0.8 mmol/L luminol and 2.0 mmol/Lα-HIBA(adjusted to pH 4.8 by HAc solution).The post-capillary reagent was 2.0 mmol/L K_3Fe(CN)_6 which was adjusted to pH 13.0 by NaOH solution.Under the optimum conditions,the detection limits(S/N=3)for Co(Ⅱ)and Cu(Ⅱ)were 7.5×10~(-11)mol/L and 7.5×10~(-9)mol/L,with the linear range of 7.5×10~(-9)mol/L to 1.0×10~(-6)mol/L and 7.5×10~(-8)mol/L to 5.0×10~(-5)mol/L, respectively.     

Two new flavonoid diglycosides from Cephalotaxus sinensis

Two new acetylated flavonoid diglycosides, scutellarein-5-O-[a-L-rhamnopyranosyl-(1→ 4)-b-D-6-O-acetylglucopyranoside] (1), apigenin-5-O-[a-L-rhamnopyranosyl-(1→2)-b-D-3,6-di-O-acetylglucopyranoside] (2), were isolated from the leaves of Cephalotaxus sinensis. Their structures were determined by chemical and spectroscopic methods including HR-FAB-MS, 1H–1H COSY, HSQC and HMBC experiments.     

The adsorption and activation of formic acid on different anatase TiO_2 surfaces

Formic acid photodegradation is one of the most important reactions in organic pollution control, and helps to improve the hydrogen generation efficiency in titanium dioxide catalyzed water photodecomposition. Based on density functional theory and Reax FF molecular dynamics, the adsorption, diffusion and activation of formic acid on the different anatase TiO_2(101),(001),(010) surfaces are investigated.The result shows that the adsorption of COOH on anatase TiO_2 surface shrinks the energy gap between the dehydrogenation intermediate COOH and HCOO. On the anatase TiO_2(101) surface, the formic acid breaks the O–H bond at the first step with activation energy 0.24 eV, and the consequent break of α-H become much easier with activation energy 0.77 eV. The dissociation of α-H is the determination step of the HCOOH decomposition.     

Simultaneous determination of seven prohibited substances in cosmetic products by liquid chromatography-tandem mass spectrometry

In this paper,we developed and validated a simple,sensitive,and selective high-performance liquid chromatography-tandem mass spectrometry(HPLC-MS/MS) method to identify and measure the following prohibited substances that may be found in cosmetic products:minoxidil,hydrocortisone, spironolactone,estrone,canrenone,triamcinolone acetonide and progesterone.Chromatographic separation was performed on a Waters Symmetry C18(100 mm×2.1 mm,3.5μm particle size) with a gradient elution system composed of 0.2%(v/v) formic acid aqueous solution and methanol containing 0.2%(v/v) formic acid at a flow rate of 0.3 mL/min.The substances were detected using a triple quadrupole mass spectrometer in the multiple reaction monitoring mode with an electrospray ionization source.All of the calibration curves showed good linearity(r > 0.999) within the tested concentration ranges.The limit of detection was <25 pg.The relative standard deviations for intraday precision for each of the prohibited substances were <3.5%at two concentration levels(2μg/g,10μg/g). The relative recovery rate for each of the prohibited substances ranged from 91.8%to 111%at three concentration levels(0.1μg/g,2μg/g,10μg/g),including the limit of quantification.In conclusion,we have developed and validated a method that can identify seven prohibited substances in cosmetic products.     

Two new C-glycosylflavones from Mimosa pudica

Two new C-glycosylflavones were isolated from the whole plant of Mimosa pudica,and their structures were determined as 6,7,3′,4′-tetrahydroxyl-8-C-[α-L-rhamnopyranosyl-(1→2)]-β-D-glucopyranosyl flavone(1),5,7,3′,4′-tetrahydroxy-8-C[β-D- apiose-(1→4)]-β-D-glycopyranosyl flavone (2).Their structures elucidated by chemical and spectroscopic analysis including IR,MS,1D and 2D NMR spectra.