射频离子源离子束成分光谱测量

为HL-2A装置中性束注入器研制了引出束功率为1MW的射频离子源。在测试平台上,实验离子源已经成功引出了束能量和束电流分别为35ke V和12.4A、束质子比为79%、脉宽为100ms的氢离子束,达到了设计束功率要求的44%。在射频离子源实验平台上,利用多普勒频移光谱方法测量了离子源引出束流成分比例,对比了束流成分和射频离子源引出束流之间的关系。实验数据分析表明,在10A引出束流的情况下,离子流成分H+1、H+2和H+3分别为75%、18%和7%。并且当引出束流从3.3A升至10.4A时,H+1从37%升至78%,而H+3则从19%降至9%。     

H+5团簇离子及其中性团簇产物H3和H4

报道了H⁺₅的实验结果.分析讨论了H⁺₅的 形成和分解途径.根据理论分析，以稳定的H⁺₃为核心与一个或多个氢分子结合可能形成稳定的H^{+_n氢团簇离子.另一方面，在高频离子源中, 有发生H+₃与H₂反应的条件.实 验中，从高频离子源引出的离子束被静电加速器加速，然后用9 关键词： +}₅团簇离子')" href="#">H⁺₅团簇离子 3中性团簇')" href="#">H₃中性团簇 4中性团簇')" href="#">H_{4中性团簇}     

射频离子源束流特性分析

介绍了为HL-2A 装置设计的引出束功率为1MW 的射频离子源研制情况。目前,在测试平台上,该离子源已经成功引出了束能量和束电流分别为35keV 和12.4A、束质子比为79%、脉宽为100ms 的氢离子束,达到了其设计束功率的44%。用红外热成像的方法测量了离子束能量密度分布。结果表明,在距离引出系统地电极 1.3m 处,束密度分布遵循高斯分布。引出束的最佳导流系数为1.689×10^–6A•V^-3/2 左右,随射频功率改变有较小的变化。根据这些实验结果,采取了相关改进措施来改善离子源的引出束性能。     

射频离子源束流特性分析

介绍了为HL-2A装置设计的引出束功率为1MW的射频离子源研制情况。目前,在测试平台上,该离子源已经成功引出了束能量和束电流分别为35ke V和12.4A、束质子比为79%、脉宽为100ms的氢离子束,达到了其设计束功率的44%。用红外热成像的方法测量了离子束能量密度分布。结果表明,在距离引出系统地电极1.3m处,束密度分布遵循高斯分布。引出束的最佳导流系数为1.689×10–6A?V-3/2左右,随射频功率改变有较小的变化。根据这些实验结果,采取了相关改进措施来改善离子源的引出束性能。     

4HeH+核间距的实验测定

用MeV量级⁴HeH⁺在超薄无衬碳膜中的库仑爆炸,获得高频离子源产生⁴HeH⁺核间距的实测值为0.094±0.003nm.发现⁴HeH⁺与H⁺₂,H⁺₃不一样,其核间距大小和离子源种类及离子源参数有密切关系,并从⁴HeH⁺的形成机理与形成条件,解 关键词：     

HD+2，H+3和D+3与固体相互作用和三体尾流效应

从分子离子H⁺₃及其氘化同位素分子离子D⁺₃和HD⁺₂与超薄固体膜相互作用发生库仑爆炸为基础,分析讨论了H⁺₃,D⁺₃和HD⁺₂三种分子离子的形成机理,根据产物能谱分布,利用库仑爆炸技术确定了同位素分子离子HD⁺₂的结构形式,给出具体核间距数值.并确定在实验中不存在线状结构的HD⁺₂.提出一种三原子分子离子和固体相互作用中尾流效应的处理方式,通过和实验结果做比较发现这是一种非常理想的处理三体尾流效应的模式,并用之进一步确认了HD⁺₂的结构形状.文章对H⁺₃,D⁺₃和HD⁺₂三种分子离子的实验结果做了对比和讨论. 关键词： +₂')" href="#">微团簇HD⁺₂ +₃和D⁺₃')" href="#">H⁺₃和D⁺₃ 库仑爆炸 三体尾流势 团簇结构     

H+2，H+3团簇离子在沟道条件下的背散射 质子产额测量

采用卢瑟福背散射方法，测得了每质子能量为650 keV的H⁺₂，H+₃团簇离子在Si晶体<100>和<110>沟道条件下的质子背散射能谱.结果发现，由于H⁺₂，H⁺₃团簇在晶体中的库仑爆炸和团簇效应，H⁺₂的背散射质子产额大于H ⁺的背散射产额，而H^{+< 关键词： 团簇 沟道效应 库仑爆炸 背散射}     

MeV氢微团簇离子与固体介质的电荷交换

利用静电加速器提供的0.6—1.8MeV的H⁺，H⁺₂，H⁺₃离子，轰击不同厚度的碳膜，分别测量这些离子通过碳膜后各种产物的产额. 得到了不同能量的H⁺通过碳膜后中性原子H和负离子H^-的产额随入射质子速度的变化关系；分别得到能量为1.2MeV,1.8MeV的H⁺₂，H⁺₃团簇离子通过不同厚度碳膜的透射产额及其与团簇离子在碳膜中驻留时间的关系；对结果进行了理论分析与讨论. 关键词： 团簇离子 电荷交换     

HL-2A装置中性束离子源引出系统束流分析

在中性束离子源引出过程中,详细分析了引出束流的产生,这有利于得到更准确的引出功率和引出电极表面的热功率沉积情况。根据HL-2A装置中性束离子源引出电极的电连接方式和束流引出的物理过程,对离子源束流引出过程进行了分析,给出抑制极电流产生的主要来源。通过分析放电气压扫描实验中的结果发现:随着放电气压的增加,不同弧放电电流情况下抑制极电流均逐渐增加,且抑制极电流与引出电流的比值近似线性增加。针对引出离子束流经过引出电极的过程建立了物理模型。计算了抑制极电流与引出电流的比值与放电气压的依赖关系,计算结果与实验结果一致,验证了引出束流分析结果的合理性。     

指数变分方法应用于电荷交换反应

本文考虑如下的电荷交换反应:H⁺+H(1s)→H(1s)+H⁺。用指数变分方法得到类H⁺₂的波函数,并将这样的波函数用于上述的电荷交换反应。对入射H⁺的能量为60和125keV的两种情况,计算了电荷交换反应的角分布。结果表明,指数变分波函数带来明显的改进,理论结果与实验数据符合得比较好。 关键词：     

研究堆慢正电子源构建中的关键机理问题

研究堆慢正电子源是获得高强度慢正电子束流的有效方式,国际上己建成多座装置并获得广泛应用.与常规同位素慢正电子源相比,研究堆慢正电子源的物理过程复杂,影响末端束流强度的因素众多,对其进行深入研究与合理建模是未来在中国绵阳研究堆(CMRR)上构建慢正电子源的基础.本文厘清了研究堆慢正电子产生的关键过程与物理机理,建立了预测末端正电子束流强度的理论模型,找到了影响其末端强度的主要物理量:快正电子体产生率、慢化体有效表面积、慢化体扩散距离、慢正电子从表面被提取到靶环末端的效率、及束流系统提取效率.用多种实验结果对模型进行校验,包括多个同位素慢正电子源的效率测量值,以及PULSTAR研究堆慢正电子源测量结果,充分验证了模型正确性.根据模型对各物理量的影响因素进行了分析,找到了需着重关注的影响因素,对未来源/靶结构的设计给出建议.     

用于中性束注入的大功率射频离子源激励器研制

建立了一个等离子体射频激励器,工作气体为氢气,工作气压为0.3Pa,激励器陶瓷桶直径300mm,工作频率1MHz。实现了RF等离子体激发放电,在输入射频功率16kW条件下,采用朗缪尔探针测得的等离子体密度>10¹⁸m^-3,初步建立了一个RF等离子体源实验平台。     

VUV photochemistry of oriented molecules: methylchloride on highly oriented pyrolytic graphite

The photoionization of CH₃Cl adsorbed on highly oriented pyrolytic graphite has been investigated as a function of the photon energy in the range 13–35 eV. Two ions were detected — CH⁺₃ and H⁺ — which show differences in their coverage and energy dependences. At very low coverages only H⁺ ions are produced, while at higher coverages (still in the monolayer regime) CH⁺₃ ions are also observed, reflecting a change in the orientation of the molecule on the surface as a function of coverage. The cross-section curves as a function of the photon energy for both ions show a maximum at 22 eV, while the onsets are at 16 eV for CH⁺₃ and 19 eV for H⁺.     

Surface enhancement of molecular ion H_2~+ yield in a 2.45-GHz electron–cyclotron resonance ion source

High current hydrogen molecular ion beam is obtained with a specially designed stainless steel liner permanent magnet2.45-GHz electron–cyclotron resonance(ECR) ion source(PMECR II) at Peking University(PKU). To further understand the physics of the hydrogen generation process inside a plasma chamber, theoretical and experimental investigations on the liner material of the plasma chamber in different running conditions are carried out. Several kinds of materials, stainless steel(SS), tantalum(Ta), quartz, and aluminum(Al) are selected in our study. Experimental results show that stainless steel and tantalum are much better than others in H~+_2 generation. During the experiment, an increasing trend in H~+_2 fraction is observed with stainless steel liner after O_2 discharge inside the ion source. Surface analyses show that the roughness change on the surface after O_2 discharge may be responsible for this phenomenon. After these studies, the pure current of H~+_2 ions can reach 42.3 mA with a fraction of 52.9%. More details are presented in this paper.     

Pulse intense metal-ion diode with a vacuum arc plasma anode

An intense pulsed ion beam of metal was extracted from a magnetically insulated ion diode operated in a mode of plasma prefill generated from a vacuum arc discharge, anode plasma source. With this ion diode, an intense metal-ion beam of a high melting-point metal (Ta) was obtained. A variety of operational modes appeared, depending on the amount of plasma in the diode gap at the initiation of the high-voltage pulse. The energy, current, and duration time of the ion beam were 20~100 keV, ~1 kA, and 1 μs, respectively. Measurements of ions were performed with an ion energy analyzer or a biased ion collector located at the end of a long drift tube and a Thomson parabola ion spectrometer. The Ta ions in the first to fifth states of ionization were detected accompanied by C⁺, O⁺, F⁺, and H⁺ . A Ta ion beam current of about half the total ion flux was obtained in this experiment     

New progress on beam availability and reliability of PKU high intensity CW proton ECR ion source

The stability and reliability of an ion source and its beam availability are extremely significant for any accelerator,especially for those high current long term CW operation ones like ADS. Although the first high quality 306-hours continuous wave(CW) operating curve at 50 m A@35 ke V has been successfully obtained with a standard compact 2.45 GHz ECR ion source at Peking University(PKU), but the uncertainties that caused beam trips before are unacceptable during an accelerator real operation and should be eliminated. Meanwhile, no permission will be given when the beam power is upgraded from 50 m A@35 ke V to 50 m A@50 ke V. To improve the PKU CW proton source quality, several upgrades were done recently. After those improvements, a new long term CW proton beam experiment at 50 m A@50 ke V was carried out in June 2016. The total running time is 300.5 hours, including near 6 hours ion source preparation and 294 hours non-disturb continuous operation. Within the continuous 13 days operation, no beam-off happened, no spark was observed,no beam drop appeared, no interrupting action was needed, and only a few beam fluctuations caused by the air conditional failure occurred. Beam availability and reliability within the 294 hours is 100%. The root-mean-square(RMS) emittance of this 50 m A@50 ke V CW proton beam is about 0.186 π.mm.mrad. A careful inspection of the ion source was done after this long term operation and no obvious damage was found. The restart experimental results obtained after the ion source inspection prove the high repeatability of PKU PMECRIS. In addition, a 130-m A H+beam was obtained at 50 k V with duty factor of 10%(100 Hz/1 ms) with this source. Details will be presented in this paper.     

Magnetic susceptibility of (IPA)2FeCl4, (IBuA)2FeCl4 and (IPA)2CuCi4 (IPA = isopropylammonium ion and IBuA = isobutylammonium ion)

The magnetic susceptibility of (IPA)₂FeCl₄, (IBuA)₂FeCl₄ and (IPA)₂CuCl₄, where IPA = (CH₃)₂CHNH⁺₃ and IBuA = (CH₃)₂CHCH₂NH⁺₃, were measured in the temperature range form 80 K up to a temperature near the melting points of the samples. The results obtained were interpreted in termw of a canted two-dimensional antiferromagnet. The variation of the magnetic susceptibility with the change in the composition was also discussed.     

Acoustic double layers in multispecies plasma

Particle simulation in a one-dimensional bounded system is used to examine the formation of acoustic double layers in the presence of two ion species. Double-layer formation depends critically on the details of the distribution functions of the supporting ion populations, and their relative drifts with respect to the electrons. The effect of having two ion components, an H⁺ and an O⁺ beam, on double-layer evolution from ion acoustic turbulence driven by an electron drift relative to the H⁺ beam of ≈0.5u _e, where uu_e is the electron thermal speed, is examined. The ratio of ion drifts is taken to be consistent with acceleration by a quasi-static auroral potential drop (i.e. V _H/V_O=√M_O/ M_H=4.0). Acoustic double layers form in either ion species on the time scale τ≈100ω_ps^-1, where ω_ps is the ion plasma frequency for species `s' and s=H or O, and for drifts relative to the electrons lower than that required for double layer formation in simulations of single ion component plasma     

微型电子回旋共振离子推力器离子源结构优化实验研究

微型电子回旋共振(ECR)离子推力器可满足微小航天器空间探测的推进需求. 为此, 本文开展直径20 mm的微型ECR离子源结构优化实验研究. 根据放电室内静磁场和ECR谐振区的分布特点, 研究不同微波耦合输入位置对离子源性能的影响, 结果表明环形天线处在高于ECR谐振强度的强磁场区域时, 微波与等离子体实现无损耦合, 电子共振加热效果显著, 引出离子束流较大. 根据放电室电磁截止特性, 结合微波电场计算, 研究放电容积对离子源性能的影响, 实验表明过长或过短的腔体长度会导致引出离子束流下降甚至等离子体熄灭. 经优化后离子源性能测试表明, 在入射微波功率2.1 W、氩气流量14.9 μg/s下, 可引出离子束流5.4 mA, 气体放电损耗和利用率分别为389 W/A和15%.