水中流光放电流光丝的再发光和暂停行为

水中流光放电是研究水中放电基本物理、化学过程的主要研究对象.本文利用四分幅超高速相机、采用针-板电极结构、在20—800μS/cm水电导率范围内研究了水中微秒脉冲流光放电流光丝的再发光和暂停行为,探讨了高水电导率下观测不到流光丝的再发光的原因.结果发现:再发光在不同的流光丝之间交替发生并存在两种模式:一种为整根丝熄灭后再发光;一种为只有先端部分发光熄灭随后恢复发光.随着水电导率的增大,观测到流光丝的再发光现象的频度急剧减小, 540μS/cm水电导率时降到零;在20—800μS/cm水电导率条件下都可观测到流光丝伴生冲击波串分段现象,冲击波串分段现象的出现频度在65%以上,表明在20—800μS/cm水电导率条件下流光丝的暂停是一种普遍行为.通过测量两段冲击波的半径差得到流光的暂停时间平均为157 ns,几乎不受水电导率的影响;随着水电导率的增大,流光丝的发光强度显著增大,水电导率大于350μS/cm时,流光丝暂停期间内流光丝的光强度无法衰减到相机分辨水平以下,在相机获得的发光图像上看上去是持续发光的,难以分辨出流光丝熄灭-再发光过程.     

Scanning tunneling optical spectroscopy in mercury cadmium telluride and related compounds

We consider II–VI narrow gap semiconducting alloys: mercury cadmium telluride, Hg_(1−x)Cd_(x)Te (MCT), mercury zinc telluride, Hg_(1−x)Zn_(x)Te (MZT), and mercury zinc selenide, Hg_(1−x)Zn_(x)Se (MZS). MCT is emphasized for actual calculations, but a table of values needed in all calculations is presented. These materials are of interest because of their application to infrared detectors and related devices, and because they are candidates for low gravity crystal growth to improve uniformity. We present new calculations of the scanning tunneling optical spectroscopy (STOS) current from which the local energy gap, a function of x, and hence the stoichiometry (x) can be determined as a function of position with presumably high spatial resolution. The low temperature tunneling current (vs. photon frequency) has a sharper onset at the band gap than the low temperature optical absorption. This sharp onset originates from the rapid increase in the integrated transmission probabilities and is greatly enhanced by large diffusion lengths. Thus, STOS should be a competitive technique, compared to optical absorption, for determining the local stoichiometry, a property that is important for characterizing crystals.     

Electron beam evaporation deposition of cadmium sulphide and cadmium telluride thin films: Solar cell applications

Cadmium sulphide (CdS) and cadmium telluride (CdTe) thin films are deposited by electron beam evaporation. Atomic force microscopy (AFM) reveals that the root mean square (RMS) roughness values of the CdS films increase as substrate temperature increases. The optical band gap values of CdS films increase slightly with the increase in the substrate temperature, in a range of 2.42-2.48 eV. The result of Hall effect measurement suggests that the carrier concentration decreases as the substrate temperature increases, making the resistivity of the CdS films increase. CdTe films annealed at 300℃ show that their lowest transmittances are due to their largest packing densities. The electrical characteristics of CdS/CdTe thin film solar cells are investigated in dark conditions and under illumination. Typical rectifying and photovoltaic properties are obtained.     

针-板DBD微流注与微辉光交替生成的机理研究

在介质阻挡放电体系中产生辉光放电可以有效的提高放电体系产生高能电子的性能, 为等离子体化学反应提供更加丰富的活性粒子.本文对针-板介质阻挡放电体系下的放电模式进行了研究,实验发现放电正负半周期表现出不同的放电模式, 激励电压为3 kV时放电正负半周期分别为微流注放电和电晕放电(或者Trichel脉冲放电),激励电压为6 kV时放电正负半周期分别为微流注放电和微辉光放电.微辉光放电形貌具有与典型辉光放电相同的分层次放电结构, 分析了激励电压6 kV时的放电过程,认为足够强的阴极电场强度和裸露针状电极形成的有效的二次电子发射过程是形成微辉光放电的主要因素,绝缘介质层的存在避免了微辉光放电向弧光放电过渡.     

重复频率脉冲流注放电演变现象与机制研究进展

重复频率脉冲流注放电是低温等离子体前沿应用的关键使能因子,然而,高重复频率脉冲作用下流注放电呈现复杂的不稳定和记忆效应现象,放电基础演变机理和调控方法尚不完善,极大影响应用的安全性和放电特性调控的有效性。综述了重复频率脉冲流注放电演变现象与机制的研究进展。首先归纳了重复频率脉冲流注放电的强非线性和渐进式演变特征,然后分析不同类型放电记忆效应因子对后续流注起始和传播的作用机制,最后总结了脉冲波形参数对重复频率脉冲流注放电的影响规律。凝练了重复频率脉冲流注放电演变机制研究的若干挑战,对脉冲放电等离子体机理研究具有一定的借鉴作用。     

正极性纳秒脉冲电压下变压器油中流注放电仿真研究

建立了二维轴对称流体模型, 仿真研究了正极性纳秒脉冲电压下变压器油中针-板电极流注放电的起始与发展过程, 得到了不同的外施电压幅值、脉冲上升沿时间与电极间隙距离下油中流注放电的形貌、 电场强度与空间电荷密度分布等. 仿真结果表明: 空间电荷加强了流注头部前方电场, 使流注通道更易于向前推进, 形成"电离波"; 随着外施电压幅值升高, 流注发展的平均速度显著变大; 较陡的脉冲上升沿形成的放电半径较大, 对应的最大电场强度值变小; 随着电极间隙距离的增加, 流注发展平均速度变快. 仿真显示纳秒脉冲下放电中油温无明显升高, 表明此类放电过程没有明显的油气化现象. 我们认为, 场致电离是油中带电粒子产生的主导机制; 空间电荷效应增强流注前方电场使得电离进一步发展, 最终导致击穿. 本研究有助于加深对变压器油中放电起始、发展直至击穿过程的认识以及对液体电介质中电离机制的理解. 关键词： 变压器油 流体模型 流注放电 空间电荷效应     

Local electron mean energy profile of positive primary streamer discharge with pin-plate electrodes in oxygen nitrogen mixtures

Local electron mean energy (LEME) has a direct effect on the rates of collisional ionization of molecules and atoms by electrons. Electron-impact ionization plays an important role and is the main process for the production of charged particles in a primary streamer discharge. Detailed research on the LEME profile in a primary streamer discharge is extremely important for a comprehensive understanding of the local physical mechanism of a streamer. In this study, the LEME profile of the primary streamer discharge in oxygen-nitrogen mixtures with a pin-plate gap of 0.5 cm under an impulse voltage is investigated using a fluid model. The fluid model includes the electron mean energy density equation, as well as continuity equations for electrons and ions and Poisson’s electric field equation. The study finds that, except in the initial stage of the primary streamer, the LEME in the primary streamer tip tends to increase as the oxygen-nitrogen mole ratio increases and the pressure decreases. When the primary streamer bridges the gap, the LEME in the primary streamer channel is smaller than the first ionization energies of oxygen and nitrogen. The LEME in the primary streamer channel then decreases as the oxygen-nitrogen mole ratio increases and the pressure increases. The LEME in the primary streamer tip is primarily dependent on the reduced electric field with mole ratios of oxygen-nitrogen given in the oxygen-nitrogen mixtures.     

针-板空气间隙流注放电起始过程的三维PIC/MCC仿真研究

流注放电作为自然界中闪电传播的预电离机制、高压输变线路间长空间间隙放电的重要初始阶段,在工业领域存在诸多潜在应用,近年来引起人们越来越多的关注.流注放电具有典型的多尺度、非线性的放电特征,实验观测中多呈现出分叉等不规则结构.为了研究其微观结构特性和行为特征,本文采用三维粒子仿真模型(PIC/MCC),着重研究了流注从针型正电极的起始和发展过程.模型采用了可变自适应网格、可变粒子权重以及并行计算等技术,有效地降低了三维粒子仿真的计算时间.通过调节针型电极上的施加电压幅值、改变气体组分及调整电极形状尺寸等,研究了放电参数变化对流注放电的分叉结构、半径等行为的影响.模拟结果表明:随着电压的升高,流注的半径及分叉数目增加;对比不同气体组分(纯氧以及不同比例氮氧混合气体),发现其对流注的分叉数目影响较为显著;针型电极结构直接影响了流注的起始时间和形貌.     

The localised modes due to P defects in cadmium telluride

Dutt and Spitzer experimentally observed the localised vibrational modes related to the phosphorus defects in CdTe andr eported that P would go either to substitutional or interstitial site. In this paper we have theoretically investigated the P defect behaviour in CdTe for those two possible sites by Green’s function technique and we believe from our calculations that P goes interstitially rather than substitutionally.     

空气中大气压下均匀辉光放电的可能性

利用介质阻挡电极结构,对101325×105Pa气压下空气间隙中的放电进行了实验研究,数值模拟计算了实验条件下电子雪崩的发展过程.结果表明:对于长度不大于2mm的空气间隙,可能实现辉光放电.对于长度不小于5mm的空气间隙,如果不能设法降低放电场强,放电必然是流注形式,不可能实现辉光放电.另外,实验结果未能验证“离子捕获”机理降低放电场强而实现辉光放电的正确性 关键词： 大气压辉光放电 电子雪崩 流注     

光电离速率影响大气压空气正流注分支的机理研究

大气压空气中的流注放电有广泛的理论和应用研究价值,包括雷电机理、输变电系统空气绝缘理论以及材料表面改性等.流注是一个快速发展的强电离区域,在传播过程中存在着一种重要的特点—分支现象.光电离为正流注发展提供必要的自由电子,且实验结果表明分支特征与流注头部的光电离速率密切相关.本文基于新的流注分支判据,采用了粒子网格单元与蒙特卡罗碰撞相结合(PIC-MCC)的三维放电模型(Pamdi3D)进行数值仿真验证.为了研究光电离速率对正流注分支的影响,仿真了毫米尺度间隙针-板电极正流注发展,系统研究了不同光电离参数的影响.当减小氮气-氧气比例、光子吸收截面或光电离效率系数后,流注均更早地出现分支现象.这些计算结果表明大气压空气中流注头部光电离速率的降低将导致其发生分支的概率更高.     

流注放电低温等离子体中电子输运系数计算的蒙特卡罗模型

流体或者粒子-流体混合数值仿真是研究流注放电基本物理机制的常用手段,而精确的电子输运系数是保证其仿真正确性的必要前提.鉴于现有电子输运系数求解工具存在一定缺陷,本文开发了采用蒙特卡罗方法求解低温等离子体中电子输运系数的仿真工具,测试表明其准确性和精确度均较高.研究了氮氧气体混合比及大气压下三体碰撞吸附对电子输运系数的影响.氮气中流注放电仿真表明,流体仿真中采用本模型改进后的电子输运系数可显著改善流注通道内部的等离子体参数分布.     

平台式和斜坡式表面放电辐射源放电特性的比较

介绍了平台式和斜坡式两种结构的表面放电辐射源,研究了在1.0 μF和1.5 μF储能电容、15~30 kV充电电压等实验条件下两种辐射源的放电特性,并对实验结果进行了比较分析。得到如下结论：对于斜坡式辐射源,增加电极间距可导致放电回路面积增大,因此等效电阻和等效电感也将增加;在相同电压及电容值条件下,斜坡式辐射源的放电电流、平均沉积功率均小于平台式辐射源的相应值,但放电沉积效率略大;电压升高使放电周期、电流达到峰值时间及放电沉积效率呈减小趋势,对于同一种辐射源,使用1.5 μF电容时放电回路参数更加匹配,放电沉积效率得到提高。     

Estimating the parameters of traps in quartz by the variable energy of stimulation optically stimulated luminescence (VES-OSL) method

Optical-cross section that is a trap parameter estimated from the measurements of optically stimulated luminescence (OSL) is not a uniquely determined physical quantity. It depends not only on temperature and the energy of stimulation light but also, in the simplest case, on the optical depth of trap, the frequency of vibration mode and on the Huang-Rhys factor, i.e. the average number of phonons involved in the process of optical excitation of electrons from trap to conduction band. Conventional OSL measurement techniques do not enable to determine directly these parameters but they could be estimated by applying the variable energy of stimulation optically stimulated luminescence (VES-OSL) method. Recently it was put in to practice and the first VES-OSL curves were presented. In this study the outcomes of VES-OSL experiments are presented together with the first attempt of direct estimating the optical depth of traps active in OSL process in quartz.     

Effect of corona discharge on cadmium sulphide and lead sulphide films

This paper describes the effect of corona discharge on cadmium sulphide (CdS) and lead sulphide (PbS) films prepared using the chemical route. The property of films before and after exposure to corona has been described in detail. The electronic properties of the CdS and PbS films have been studied by current-voltage (I-V), capacitance-voltage (C-V) measurements. The structural properties and surface morphology were studied by using X-ray diffraction and scanning electron microscopy before and after exposing to Corona discharge. The films displayed the change in surface morphology after exposure to the corona discharge. It has been found that the films showed an increase in resistivity after exposure. This change in property has been attributed to modification in surface states. Time-dependent recovery indicated that room temperature annealing is sufficient to regain the normal resistivity of the films. The experiment was carried with the aim of studying the effect of the interaction of corona discharge on the semiconductor films and its subsequent effects.     

平台式和斜坡式表面放电辐射源放电特性的比较

 介绍了平台式和斜坡式两种结构的表面放电辐射源,研究了在1.0 μF和1.5 μF储能电容、15~30 kV充电电压等实验条件下两种辐射源的放电特性,并对实验结果进行了比较分析。得到如下结论：对于斜坡式辐射源,增加电极间距可导致放电回路面积增大,因此等效电阻和等效电感也将增加;在相同电压及电容值条件下,斜坡式辐射源的放电电流、平均沉积功率均小于平台式辐射源的相应值,但放电沉积效率略大;电压升高使放电周期、电流达到峰值时间及放电沉积效率呈减小趋势,对于同一种辐射源,使用1.5 μF电容时放电回路参数更加匹配,放电沉积效率得到提高。     

介质阻挡放电斑图中放电通道的相互作用研究

在近大气压介质阻挡放电中，研究了六边形斑图的空间波长随放电参数的变化，仔细观察了稳定的六边形中放电通道的产生及运动行为.结果表明空间波长随电压增加而减小，变化曲线与放电间隙和气压有关.电压升高，边界处生成新的放电丝，位于六边形最外层顶点处新生成的放电丝沿径向运动，而位于六边形边长上新生成的放电丝的运动方向平行于距其最近的C₂轴(过六边形顶点). 继续升高电压，放电丝变为条状进而形成螺旋波或靶波.在观察实验结果和分析放电丝受力的基础上，认为放电区域可能存在一种类似二维库仑晶体中存在的约束势. 关键词： 介质阻挡放电 斑图 放电通道 约束势     

氦,氢,氮空心阴极放电的真空紫外辐射特性

介绍了一种水冷、陶瓷封接结构的空心阴极放电装置.研究了He、H_2、N_2在120nm～20Onm范围内该装置的真空紫外辐射特性,获得了100～600mA电流范围内的辐射强度与放电电流的关系,以及充气气压变化对它的影响.实验表明:在实验条件下,主要发射谱线为氮的原子线和氦的离子线;辐射谱线强度在0.03～0.72mW·cm~(-2);气压改变时,N_2、H_2辐射强度有一极大值,而He的离子线辐射强度则出现二个极大;在He/H_2混合气体放电时,随着He的加入,氢分子带光谱有明显下降.     

标准有限元方法模拟大气压流注等离子体中数值振荡与伪扩散问题研究与改进

基于商用软件的等离子体数值模拟方案大多是基于标准Galerkin格式的有限元方法,在计算大气压流注放电时,存在数值振荡和伪扩散的问题,计算结果可靠性不高.针对针-板体流注放电结构,构建了修正的COMSOL Multiphysics等离子体模型.修正模型与COMSOL Multiphysics内置等离子体模块的区别主要在于增加了基于弱形式的人工稳定项.利用修正模型复现了经典的雪崩-流注转捩算例,并与经典纳秒秒冲过电压针板放电实验结果进行了对比验证.结果表明,引入修正后的商用软件模型能够克服数值振荡和伪扩散缺陷,确保等离子体数值计算的准确性和可复现性.