On-line monitoring of cyanide concentration via a gas membrane system in extractive metallurgical processes

The principle of molecular diffusion of gaseous HCN across a tubular microporous hydrophobic PTFE membrane directly immersed in an alkaline solution or in an aqueous mineral suspension has been applied to the design of an on-line sensing system for cyanide. It offers an efficient detection of “available” cyanide and does not require acidification and solution sampling in the reactor. Gaseous HCN diffused through the membrane is dissolved by a sodium hydroxide carder solution which is then submitted to a spectrophotometric analysis by the pyridine-barbituric acid method. The problems related to filtering of sludges are therefore overcome, and many chemical interferences can be eliminated. Complexation reactions of cyanide by metallic cations and the cyanide-consuming properties of sulphide minerals and ores were studied. This method allows the determination of concentrations down to ca. 6 × 10^?7 mol l^?1 HCN + CN^? in the reactor at Ph 10 with a 120-cm membrane tube and a carrier solution flow-rate of 8 cm³ min^?1.     

A novel spectrophotometric method for determination of cyanide using cobalt (II) phthalocyanine tetracarboxylate as a chromogen

Cobalt (II) phthalocyanine tetracarboxylate [Co (II)Pc-COOH] has been prepared and used in aqueous solutions as a novel chromogenic reagent for the spectrophotometric determination of cyanide ion. The method is based on measuring the increase in the intensity of the monomer peak in the reagent absorbance at 682 nm due to the formation of a 1 : 2 [Co (II)Pc-COOH] : [CN] complex. The complex exhibits a molar absorptivity (ε) of 7.7 × 10⁴ L mol^?1 cm^?1 and a formation constant (K_f ) of 5.4 ± 0.01 × 10⁶ at 25 ± 0.1°C. Beer's law is obeyed over the concentration range 0.15–15 µg mL^?1 (5.8 × 10^?6–5.8 × 10^?4 M) of cyanide ion, the detection limit is 20 ng mL^?1 (7.7 × 10^?7 M) the relative standard deviation is ±0.7% (n = 6) and the method accuracy is 98.6 ± 0.9%. Interference by most common ions is negligible, except that by sulphite. The proposed method is used for determining cyanide concentration in gold, silver and chromium electroplating wastewater bath solutions after a prior distillation with 1 : 1 H₂SO₄ and collection of the volatile cyanide in 1 M NaOH solution containing lead carbonate as recommended by ASTM, USEPA, ISO and APAHE separation procedures. The results agree fairly well with potentiometric data obtained using the solid state cyanide ion selective electrode.     

Salts of HCN‐Cyanide Aggregates: [CN(HCN)2]− and [CN(HCN)3]−

Although pure hydrogen cyanide can spontaneously polymerize or even explode, when initiated by small amounts of bases (e.g. CN^?), the reaction of liquid HCN with [WCC]CN (WCC=weakly coordinating cation=Ph₄P, Ph₃PNPPh₃=PNP) was investigated. Depending on the cation, it was possible to extract salts containing the formal dihydrogen tricyanide [CN(HCN)₂]^? and trihydrogen tetracyanide ions [CN(HCN)₃]^? from liquid HCN when a fast crystallization was carried out at low temperatures. X‐ray structure elucidation revealed hydrogen‐bridged linear [CN(HCN)₂]^? and Y‐shaped [CN(HCN)₃]^? molecular ions in the crystal. Both anions can be considered members of highly labile cyanide‐HCN solvates of the type [CN(HCN)_n]^? (n=1, 2, 3 …) as well as formal polypseudohalide ions.     

The relaxation of HCN(011) by V-T,R and V-V energy transfer

Tuned output from an optical parametric oscillator has been used to excite HCN directly to its (011) level. By careful use of a “cold-gas filter”, it has proved possible to distinguish between the time-resolved fluorescence from HCN(011) and that from HCN(001) formed during collisional relaxation. Rate constants for relaxation from both levels have been obtained for the partners: (i) He, Ne, Ar and Kr, and (ii) HCN, CO₂, N₂O, OCS, CS₂, C₂H₂ and C₂D₂. With the rare gases, HCN(011) is relaxed to (001) by V-T,R energy transfer, with rate constants (cm³ molecule^?1 s^?1) at 298 ± 4 K of: k_He⁰¹¹ = (7.9 ± 1.05) × 10^?13; k_Ne⁰¹¹ = (1.56 ± 0.12) × 10^?13; k_Ar⁰¹¹ = (1.20 ± 0.17) × 10^?13; k_Kr⁰¹¹ = (6.7 ± 0.65) × 10^?14. The molecular collision partners also transfer HCN(011) to (001). The rates are much greater and clearly near-resonant V-V energy exchange is important. The results are compared to first-order Sharma-Brau theory, with fair agreement where near-resonant channels exist.     

Shock tube pyrolysis of pyrrole and kinetic modeling

The kinetics of pyrolysis of pyrrole dilute in argon have been studied in a single pulse shock tube, using capillary column GC, together with GC/MS and FTIR for product identification, over the temperature range 1200–1700 K, total pressures of 7.5–13.5 atm and nominal mixture compositions of pyrrole of 5000 and 700 ppm (nominal concentrations of 5 × 10^?7 and 7 × 10^?8 mol cm^?3). Time-resolved measurements of the rate of disappearance of pyrrole behind reflected shock waves have been made by absorption spectroscopy at 230 nm, corresponding to the lowest ¹π* ← ¹π transition of pyrrole at pressures of 20 atm and mixture compositions between 1000–2000 ppm pyrrole (1.7–3.0 × 10^?7 mol cm^?3) over the temperature range of 1300 to 1700 K. At the lower end of the studied temperature range, the isomers of pyrrole, allyl cyanide and cis- and trans-crotononitrile, were the principal products, together with hydrogen cyanide and propyne/allene. At elevated temperatures, acetylene, acetonitrile, cyanoacetylene, and hydrogen became important products. The rate of overall disappearance of pyrrole, as measured by absorption spectrometry, was found to be first order in pyrrole concentration, with a rate constant k_dis(pyrrole) = 10^14.1±0.7 exp(?74.1 ± 3.0 kcal mol^?1/RT) s^?1 between 1350–1600 K and at a pressure of 20 atm. First order dependence of pyrrole decomposition and major product formation was also observed in the single pulse experiments over the range of mixture compositions studied. A 75-step reaction model is presented and shown to substantially fit the observed temperature profiles of the major product species and the reactant profile. In the model the initiation reaction is postulated to be the reversible formation of pyrrolenine, (2H-pyrrole). Pyrrolenine can undergo ring scission at the C2? N bond forming a biradical which can rearrange to form allyl cyanide and crotononitrile or undergo decomposition to form HCN and C₃H₄ or acetylene and a precursor of acetonitrile. The model predicts an overall rate of disappearance of pyrrole in agreement with the experimental measurements.     

Investigations on Bioanalytical Chemistry Part I. On Differential Pulse Voltammetry of Bilirubin

Abstract

The electrochemical behaviour of the bilirubin in many kinds of supporting electrolytes on a glassy carbon electrode (GCE) and a hanging mercury drop electrode (HMDE) was investigated by means of anodic or cathodic differential pulse voltammetry. The influences of different methods of pre-treatment of the glassy carbon electrode was also discussed. In Na₂B₄.O₇-KH₂PO₄ buffer solution, the linear range was 2×10^?9-1×10^?9 mol/l and the detection limit was 3.3×10^?9 mol/l by anodic differential pulse voltammetry at GCE. A linear relationship holds between the peak current and the concentration of bilirubin in a concentration range of 1×10^?9-4×10^?7 mol/l with good precision and accuracy, and the limit of detection was 2×10^?10 mol/l, when cathodic differential pulse adsorption voltammetry at HMDE was used.     

Conductivity of crosslinked poly(N-vinylpyrrolidone) gel film containing surfactant as electrolyte salt

New polymeric solid electrolyte films, consisting of crosslinked poly(N-vinylpyrrolidone) (PVPD) as matrix, and surfactant, sodium deoxycholate (NaDC), lithium deoxycholate (LiDC), sodium laulylsulfate (R₁₂OSO₃Na), or sodium palmitate (R₁₅COONa) as electrolyte salt, are prepared; their basic structure and conductivity dependence on temperature are reported. The structure of the electrolytes is amorphous. Their conductivity is 3.1 × 10^?5 S cm^?1 (containing NaDC), 8.42 × 10^?6 S cm^?1 (LiDC), 2.18 × 10^?4 S cm^?1 (R₁₂OSO₃Na), and 7.27 × 10^?5 S cm^?1 (R₁₅COONa) at 20°C. Their temperature dependence of the conductivity is similar to that of liquid electrolyte rather than that of usual polymeric solid electrolyte, i.e., the WLF-type dependence. The values of activation energy of conductivity (E_a) were PVPD, 25.5 kJ mol^?1; PVPD/NaDC, 21.4 kJ mol^?1; PVPD/LiDC, 25.3 kJ mol^?1; PVPD/R₁₂OSO₃Na, 17.2 kJ mol^?1; PVPD/R₁₅COONa, 18.7 kJ mol^?1. © 1993 John Wiley & Sons, Inc.     

Ionic conductivity of Li2MgSn3O8 ramsdellite

The ionic conductivity of polycrystalline pellets of Li₂MgSn₃O₈ with ramsdellite-type structure was measured by complex impedance technique. The conductivity is 1.2 × 10^?8 (Ω cm)^?1 at 300°C and 2.3 × 10^?4 (Ω cm)^?1 at 450°C. The results are discussed in relation to structural properties.     

Ionic conductivity of Li7BiO6

The ionic conductivity of polycrystalline Li₇BiO₆ pellets has been measured by complex impedence method. The conductivity is 5.7 × 10^?3 (Ω cm)^?1 and 300°C and 3.8 × 10^?6 (Ω cm)^?1 at 100°C. Li₇BiO₆ is the best lithium conductor among the structurally related Li_nMO₆ compounds.     

Indirect Atomic Absorption Spectrometric Determination of Ammonia,Thiosulfate and Cyanide in an Unsegmented Flow System

Abstract

A flow injection analysis method (FIA), has been developed for the determination of cyanide, thiosulfate and ammonia by atomic absorption spectrometry (AAS). Aqueous solution of the analyte was injected into an on-line column containing glass beads and packed with silver chloride and deionized water was used as the carrier. The analyte dissolves the silver chloride and the dissolved silver complex is introduced to the nebulizer of the AAS. This method has proved to be sensitive, simple and precise. Detection limits of 1.0 × 10^?7 M, 5.0×10^?7 M and 5.0x10^?6M were obtained for thiosulfate, cyanide and ammonia, respectively. The precision of the technique was 2.0%, 2.4% and 1.4% in case of thiosulfate, cyanide and ammonia, respectively. The effects of flow rate and sample volume on the FIA/AAS signals are presented.     

Polyethyleneoxide (PEO)-based, anion conducting solid polymer electrolyte for PEC solar cells

Solid polymer electrolyte membranes were prepared by complexing tetrapropylammoniumiodide (Pr₄N⁺I^?) salt with polyethylene oxide (PEO) plasticized with ethylene carbonate (EC), and these were used in photoelectrochemical (PEC) solar cells fabricated with the configuration glass/FTO/TiO₂/dye/electrolyte/Pt/FTO/glass. The PEO/Pr₄N⁺I^?+I₂?=?9:1 ratio gave the best room temperature conductivity for the electrolyte. For this composition, the plasticizer EC was added to increase the conductivity, and a further conductivity enhancement of four orders of magnitude was observed. An abrupt increase in conductivity occurs around 60–70 wt% EC; the room temperature conductivity was 5.4?×?10^?7 S cm^?1 for 60 wt% EC and 4.9?×?10^?5 S cm^?1 for the 70 wt% EC. For solar cells with electrolytes containing PEO/Pr₄N⁺I^?+I₂?=?9:1 and EC, IV curves and photocurrent action spectra were obtained. The photocurrent also increased with increasing amounts of EC, up to three orders of magnitude. However, the energy conversion efficiency of this cell was rather low.     

Oxygen-ionic conductors based on substituted bismuth molybdates with column-type structural fragments

The possibility of synthesizing oxygen-ionic conductors from substituted bismuth molybdates containing [Bi₁₂O₁₄] _n ⁸ⁿ⁺ columns, MoO₄ tetrahedra, and isolated Bi ions in their structure was studied. The specifics of their structure and electric conductivity were investigated. The general formula of the solid solutions can be recorded as Bi₁₃Mo_{5 ? x} Me _x O_{34 ? δ}, where Me is the fouror five-valent d metal (Ti, Zr, V, Nb). The electric conductivity of doped bismuth molybdates considerably increased compared with that of the matrix compound. The electric conductivity reached 5.5 × 10^?3 S cm^?1 at 700°C and 1.8 × 10^?4 S cm^?1 at 350°C for the zirconium-doped compound with x = 0.4. The porosity of the ceramics was less than 5%; the thermal expansion coefficient was of the order of 14 × 10^?6 K^?1. Based on the set of their characteristics, these compounds are recommended as materials for membranes of electrochemical devices.     

Investigations on Adsorption Potentiometry Part V Derivative Adsorption Chronopotentiometry of Beryllium(II)-4-[(4-diethylamino-2-hydroxypheanyl)-azo]-5-hydroxy-naphthalene-2,7-disurphonic Acid System

Abstract

An electroanalytical methood, based on derivative chronopotentiometry of the complex of beryllium(II) with 4-[(4-diethylamino-2-hydroxy-phenyl)-azo]-5-hydroxy-naphthalene-2,7-disurphonic acid (Beryllon II) accumulated adsorptively on the surface of a hanging mercury drop electrode, has been developed for determining trace beryllium in food. The dependences of the peak height on the dt/dE vs. E curve on the pre-concentration time, preconcentration potential and the constant reducing current are discussed. In 0.15 mol/1 NH_s+0.05 mol/1 NH₄Cl, 4×10^?7 mol/l Beryllon II, and at a preconcentration potential of -0.30 V (ve. SCE), the limit of detection and linear range are 1 × l0^?10 mol/l and 3 × 10^?10 -2 × l0^?7 mol/l, Iwpectively. The relative standard error of the method is 2.3% for 6 × 10^?8 mol/l Be(II). The method WBB applied to samples of food. The electrode procees hae been diecueeed.     

A Novel Optical Sensor for Determination of Thiocyanate

Abstract

A novel optical sensor (optode) is described for the determination of thiocyanate using methyltrioctylammonium chloride immobilized on triacetylcellulose membrane. The response to thiocyanate is the result of adsorption of [Co(SCN)₄]^2? on sensing membrane, which caused the colorless membrane to change to blue. This optode can readily be regenerated by using 0.02 mol/l sodium oxalate solution. The linear range of the method was 3.44×10^?5 to 8.61×10^?4 mol/l of thiocyanate with a limit of detection 1.51×10^?5 mol/l. The relative standard deviation for eight replicate measurements of 8.61×10^?5 and 4.30×10^?4 mol/l of thiocyanate was 3.45 and 1.23%, respectively. The sensor was successfully applied for the determination of thiocyanate in saliva of smokers, nonsmokers and various water samples.     

Spectrophotometer Determination of Nitrite Using Salbutamol sulphate as a Reagent

Abstract

A simple spectrophotometric method for the trace determination of nitrite (NO^? ₂) is described. Nitrite is reacted with Salbutamal sulphate in acidic medium which gives a yellow colour in alkaline medium (?pH 7) and can be determined in the presence of several cations and anions. Beer's law is obeyed in the range of 1.8 to 27.6 ppm of nitrite with the molar absorptivity 1.8 × 10³ 1 × mole^?1 × cm^?1 at 4l0 nm. The proposed method can also be utilized for the determination of nitrate (NO^? ₃) after its reduction to nitrite. The method has been applied for the determination of various samples containing traces of nitrite.     

Gas phase thermal diffusivities by a thermal lens technique

A simplified design of thermal lens apparatus is presented in which a chopped cw argon laser beam produces a transient thermal lens in a cylindrical gas cell. The axial intensity variation of a cw helium-neon laser probing this lens is analysed to yield the thermal diffusivities and thus the thermal conductivity coefficients of Kr, CO₂, CH₄, C₂H₆, C₃H₈, C₃H₆ and C₄H₁₀ as 9.4 × 10^?3 ± 4%, 1.6 × 10^?2 ± 3%, 2.98 × 10^?2 ± 4%, 2.03 × 10^?2 ± 4%, 2.05 × 10^?2 ± 7%, 1.6 × 10^?2 ± 8% and 1.9 × 10^?2 ± 8% respectively in W m^?1 K^?1 at 300 K. The method is rapid, requiring only that the sample be transparent at both laser frequencies used. A simplified mathematical analysis is shown to be adequate for this system. For the conditions specified, self-lensing of the argon laser beam is shown to be compensated by using an effective laser beam diameter.     

New solid polymer electrolytes based on polyester diacrylate for lithium power sources

New solid polymer electrolytes are developed for a lithium power source used at the temperatures up to 100°C. Polyester diacrylate (PEDA) based on oligohydroxyethylacrylate and its block copolymers with polyethylene glycol were offered for polymer matrix formation. The salt used was LiClO₄. The ionic conductivity of electrolytes was measured in the range of 20 to 100°C using the electrochemical impedance method. It is shown that the maximum conductivity in the whole temperature range is characteristic of the electrolyte based on the PEDA copolymer and polyethylene glycol condensation product (2.8 × 10^?6 S cm^?1 at 20°C, 1.8 × 10^?4 S cm^?1 at 95°C).     

Electrical Properties of Sm‐doped Ceria (SDC) and SDC Carbonate Composite

This study prepared a dense Sm‐doped ceria (SDC) and an SDC carbonate composite (abbreviated as SDC‐C). The latter was prepared by immersing porous SDC with a formula of (Ce_0.8Sm_0.2)O_1.9 and a relative density of approximately 65‐70% into a molten mixture of carbonates containing 1:1 molar ratio of Li₂CO₃ and Na₂CO₃ at 500 °C. The relative density of the SDC‐C was close to 100%. In addition, SDC oxide without carbonates, which also has a relative density of close to 100%, was heat treated at 1600 °C. At 500 °C, the electrical conductivity and ionic transference number (t_i) of the SDC oxide were 1.79(5) × 10^?3 S·cm^?1 and 0.99(2), respectively, such that electronic conduction could be disregarded. Increasing the temperature caused a gradual decrease in the t_i of SDC. Following the addition of carbonates to SDC, the electrical conductivity reached 1.23(9) × 10^?1 S·cm^?1 at 500 °C. After 14 days (340 h), the electrical conductivity of the SDC‐C at 490 °C, leveled off at about 6 × 10^?2 S·cm^?1. SDC‐C could be used as a potential electrolyte in solid oxide fuel cells (SOFCs) at temperatures below 500 °C.     

Carbon monoxide :acceptor oxidoreductase from Pseudomonas thermocarboxydovorans strain C2 and its use in a carbon monoxide sensor

The carbon monoxide:acceptor oxidoreductase from autotrophically-grown Pseudomonas thermocarboxydovorans strain C2 was purified to 95% homogeneity and found to contain fiavin, iron, acid-labile sulphide and possibly molybdenum; its molecular weight was 2.7 × 10⁵. The enzyme catalyzed the oxidation of CO to CO₂ with various electron acceptors including phenazine ethosulphate, methylene blue, hexacyanoferrate(III) and ferrocene derivatives (ferrocene monocarboxylic acid, 1,1′dimethylferrocene and horse heart cytochrome C) but not viologen dyes, NAD(P) and oxygen. The optimum pH and temperature for enzyme activity in the in vitro assay were 7.5 and 80°C, respectively. Carbon monoxide is the only known electron donor (apparent K_m 5 × 10^?7 M) and acetylene, cyanide, 8-quinolinol and sulphydryl reagents inhibited the enzyme. Second-order homogeneous rate constants for the reaction between the reduced enzyme and either cytochrome C (3.0 × 10⁴ l mol^?1 s^?1) or the ferricinium ion of ferrocene monocarboxylic acid (4.0 × 10⁵ l mol^?1 s^?1) were calculated by using cyclic voltammetry. The latter reaction was exploited by incorporating 1,1′-dimethylferrocene in a carbon electrode and retaining carbon monoxide oxidoreductase behind a membrane at the surface. The probe gave a linear current response to aqueous concentrations of carbon monoxide up to 65 μM and achieved a steady current in < 15 s. A similar configuration was used to detect gaseous carbon monoxide. With a fuel cell mode, 20 nmol could be detected.     

An Atomic Absorption Analysis Method for Cyanide

Abstract

An atomic absorption analysis procedure for cyanide has been developed. The procedure is based upon the solubilization of copper(II) from a basic copper carbonate in an alkaline medium. The amount of copper complexed by the cyanide ion is determined by atomic absorption and a calibration curve is constructed concurrently. The stoichiometry of the cyanide-copper complex is 3:1, implying formation of the complex ion Cu(CN)^? ₃, with no formation of CuCN observed at the low concentration of cyanide used. The method is used primarily for analyzing low levels of cyanide; the sensitivity of the method extending down to 2.0 × 10^?5 M CN^?. The most likely interference, iron, is considered. Finally, recovery of cyanide from spiked samples is demonstrated.