Thermally tunable narrow-bandpass filter based on a linearly chirped fiber Bragg grating

We propose a new method for the development of a tunable optical bandpass filter (TOBF) based on a linearly chirped fiber Bragg grating (LCFBG). A NiCr wire heater is used to heat the LCFBG at a small point to introduce a narrow passband within the stop band of the LCFBG. The central wavelength of the passband is tuned by scanning the wire heater along the LCFBG. As an example demonstrating the effectiveness of the proposed method, we demonstrate a TOBF with a very small 3-dB bandwidth of approximately 7 pm, a tuning range of 16.4 nm, and a rejection ratio of more than 25 dB. Compared with previously reported tunable-fiber-based bandpass filters, this method provides the advantages of a large tuning range, continuous tunability, a switchable passband, a simple tuning mechanism, low cost, and narrow bandwidth.     

All-optical microwave bandpass filter and phase shifter using a broadband optical source and an optical phase modulator

We propose a system that can perform microwave bandpass filtering and phase shifting simultaneously without redundant optical-electrical and electrical-optical conversions. The principle is based on polarization-dependant phase modulation of a broadband optical source and the variable optical carrier time shift method. A single-bandpass microwave photonic filter with a central frequency of 10.8 GHz, a 3-dB bandwidth of 670 MHz, and a 360° phase tuning range is experimentally demonstrated. The capability of our configuration to implement wideband phase shifters is also verified.     

Tunable optical filter using second-order micro-ring resonator

In this paper, we design and fabricate a silicon integrated optical filter consisting of two cascaded micro-ring resonators and two straight waveguides. Two micro-heaters are fabricated on the top of two micro-rings respectively, which are employed to modulate the micro-rings to perform the function of a tunable optical filter by the thermo–optic effect. The static response test indicates that the extinction ratio and 3-d B bandwidth are 29.01 d B and 0.21 nm respectively, the dynamic response test indicates that the 10%–90% rise and 90%–10% fall time of the filter are 16 μs and 12 μs, respectively,which can meet the requirements of optical communication and information processing. Finally, the power consumption of the device is also characterized, and the total power consumption is about 9.43 m W/nm, which has been improved efficiently.     

Photonic microwave bandpass filter with improved dynamic range

A technique to improve the dynamic range of a photonic microwave bandpass filter is proposed and experimentally demonstrated. The filter is implemented based on phase modulation to intensity modulation conversion using fiber Bragg gratings (FBGs) serving as frequency discriminators, with the optical carriers located at the left or right slopes of the FBGs, to generate positive or negative tap coefficients. The dynamic range of the photonic microwave bandpass filter is increased by reducing the optical-carrier-induced shot noise and relative intensity noise at the photodetector, which is realized by placing the optical carriers at the lower slopes of the FBG reflection spectra. A photonic microwave bandpass filter with an improvement in dynamic range of about 10 dB is demonstrated.     

Narrowband optical filter, with a variable transmission spectrum, using stimulated Brillouin scattering in optical fiber

A novel shape-adjustable narrowband optical filter utilizing stimulated Brillouin scattering in an optical fiber is proposed and demonstrated. In this scheme, binary-phase-shift-keying modulation is applied to the pump wave to broaden and shape the Brillouin gain spectrum. By choosing an appropriate modulation data pattern, we realized a flat-top steep-cutoff optical bandpass filter with a 3-dB bandwidth of 1.5 GHz and a 10-dB bandwidth of 2 GHz is realized. In addition, a tunable optical notch filter is also realized by deamplification of the anti-Stokes wave.     

谐振腔侧边1×5介质柱调谐光子晶体滤波器

在正方格二维光子晶体结构中设计了基于可调谐谐振腔的带通滤波器,通过改变1×5谐振腔侧边调谐介质柱位置调节谐振腔与波导系统工作时传输的波段,用CMT理论分析了输入端耦合衰减率及输入端失谐因子对滤波器的影响。借助FDTD方法得到了滤波器波长传输谱,结果表明:当滤波器结构工作于1320~1810 nm波长段时,输出端38个通帯的-3 dB带宽Δλ范围为4.18~11.15 nm,通带峰值波长可调宽度为186.56 nm。该微型滤波器适于光电通信粗波分解复用WDDM系统设计和光集成设计等方面。     

Tunable Optical Add/Drop Multiplexers Using Cascaded Mach Zehnder Coupler

A tunable add/drop filter based on Cascaded Mach Zehnder (CMZ) coupler using SiO₂/silicon oxinitride (SiON) is presented with its mathematical model. The increase of filtered width (i.e., free spectral response) and lowering of crosstalk for this filter are optimized using its mathematical model with truncated binomial coupler distribution. The number of wavelength channels with 100 GHz (0.8 nm) channel spacing for 5-stage (M = 9, r = 2) truncated binomial CMZ filter with index contrast ∼5% at -20 dB crosstalk and the bending loss of 0.1 dB per MZ section are obtained as ∼37 (free spectral range of 31 nm). It is seen that if during the fabrication process, waveguide core width w is increased or decreased by 0.1 μm (in percentage terms ∼±6.6%), the crosstalk is slightly increased by ∼7%. Thermal tuning for wavelength channels is achieved by thin film heater with low power thermooptic delay line structure which reduces the heating power by ∼1.58 times in comparison to the conventional structure.     

Tunable single-longitudinal-mode Ytterbium all fiber laser with saturable-absorber-based auto-tracking filter

A broadband tunable, single-longitudinal-mode (SLM) Ytterbium fiber laser with unpumped Ytterbium-doped Sagnac loop is proposed and demonstrated experimentally. The unpumped Ytterbium-doped Sagnac loop is employed as a saturable absorber based auto-tracking filter to ensure single-longitudinal-mode oscillation. And a tunable band pass optical filter with large tuning range is applied to achieve broadband tuning ability. With 1-m Ytterbium-doped fiber as the gain medium, the SLM operation is achieved with over 60-nm wavelength tuning range at 160-mW pump power. The laser is very stable with output power of about 3 dBm and optical signal to noise ratio of higher than 50 dB in all the 60-nm tuning range.     

C-band three-port tunable band-pass thin film optical filter with low polarization-sensitivity

According to the oblique incidence characteristics of thin film narrowband filter, the stack of 100 GHz DWDM four cavities angle-tuned thin film filter has been designed and optimized. The two polarization modes’ central wavelengths of the thin film filter can be centered at the same one in oblique incidence, and it has a stable tuning range of 20 nm without the phenomenon of polarization central wavelength separation. Using this kind of angle-tuned thin film filter and the polarization beam-splitters, the tuning range of the angle-tuned thin film filter can be further expanded due to the reason that it can transmit only the s-polarization light. In this paper we also developed a three-port bandpass tunable filter device with new structure, which tuning range can cover the whole C-band and its adjacent channel isolation degree is high. The experiments show that the three-port tunable filter has an effective tuning range of 33 nm, and its adjacent channel isolation degree is more than 35 dB. It has a bright application opportunity for its flexibility and effective performance.     

Thermally switchable and discretely tunable comb filter with a linearly chirped fiber Bragg grating

We propose and experimentally demonstrate a novel switchable and discretely tunable comb filter based on a thermally induced linearly chirped fiber Bragg grating. Experimentally we achieved a thermally induced optical bandpass filter that has eight switchable passband peaks with peak separations of 1.6 and 3.2 nm, a very narrow bandwidth (as small as 10 pm) of each peak, a tunable range of 16.5 nm, and a greater than 25 dB rejection ratio. Two spectral peaks separated by only 0.8 nm were also obtained with this comb filter. This filter provides the unique advantages of an all-fiber structure, switchable spectral peaks, independent tuning of the center wavelength and wavelength spacing of the spectral peaks, low polarization sensitivity, simple structure, ease of fabrication, and low cost.     

Demonstration of a bandwidth-tunable optical passband filter with tunable attenuation

A bandwidth-tunable optical passband filter with tunable attenuation is proposed. The filter, composed of a transmission liquid crystal array and high-resolution diffraction grating, was successfully demonstrated based on the compact spatial light design. Experimental results showed that the bandwidth, wavelength, and attenuation could be tuned by controlling the voltage applied on the liquid crystal array. The insertion loss was less than 3 dB;the attenuation tuning range was from 0 to 15 dB. The bandwidth tuning range was from 50 to 5000 GHz, which covered the full C band. The filter can meet the technical requirements of colorless-directionless-contentionlessflexible reconfigurable optical add/drop multiplexer.     

Superconducting tunable filter with constant bandwidth using coplanar waveguide resonators

In this paper we propose a two-pole varactor-tuned superconducting filter using coplanar waveguide(CPW) spiralin-spiral-out(SISO) resonators. Novel internal and external coupling structures are introduced to meet the requirements for a tunable filter with a constant absolute bandwidth. The fabricated device has a frequency tuning range of 14.4%at frequencies ranging from 274.1 MHz to 317.7 MHz, a 3-d B bandwidth of 5.14 ± 0.06 MHz, and an insertion loss of0.08 d B–0.70 d B. The simulated and measured results are in excellent agreement with each other.     

一种高选择性可调带通与带阻可切换滤波器

设计了一种高选择性可调带通与带阻可切换微带滤波器。在微带谐振器及枝节末端加载变容二极管实现中心频率的可调;在输入与输出端口馈线之间,利用PIN二极管实现滤波器阻带和通带特性的切换。采用奇偶模的方法对滤波器结构进行分析,通过对奇偶模频率的调节实现了频率调节过程中的恒定绝对带宽。同时,在输入与输出馈线间引入源与负载耦合,使得频带两侧各有一个传输零点,且传输零点在整个频率调谐范围内相对位置几乎不变。因此,在整个频率调节范围内,滤波器实现了高选择性及良好的带外抑制能力。最终设计出的可调带阻滤波器的频率调谐范围为5.58～5.89 GHz,绝对带宽80 MHz±5 MHz,阻带衰减优于14 dB;可调带通滤波器的频率调谐范围为5.42～5.79 GHz,绝对带宽120 MHz±5 MHz,插入损耗1.69～2.25 dB,回波损耗优于13 dB。同时,该滤波器具有0.28λ_g×0.62λ_g（λ_g是可调频率范围中心频率的波长）的紧凑结构尺寸。实验和仿真结果一致性较好。     

Tunable Optical Add/Drop Multiplexers Using Cascaded Mach Zehnder Coupler

Abstract

A tunable add/drop filter based on Cascaded Mach Zehnder (CMZ) coupler using SiO₂/silicon oxinitride (SiON) is presented with its mathematical model. The increase of filtered width (i.e., free spectral response) and lowering of crosstalk for this filter are optimized using its mathematical model with truncated binomial coupler distribution. The number of wavelength channels with 100 GHz (0.8 nm) channel spacing for 5-stage (M = 9, r = 2) truncated binomial CMZ filter with index contrast ～5% at ?20 dB crosstalk and the bending loss of 0.1 dB per MZ section are obtained as ～37 (free spectral range of 31 nm). It is seen that if during the fabrication process, waveguide core width w is increased or decreased by 0.1 μm (in percentage terms ～±6.6%), the crosstalk is slightly increased by ～7%. Thermal tuning for wavelength channels is achieved by thin film heater with low power thermooptic delay line structure which reduces the heating power by ～1.58 times in comparison to the conventional structure.     

Dual-band optical filter based on a single microdisk resonator

We propose and experimentally demonstrate a dual-band optical filter based on a single microdisk resonator. An analytical model is built based on the transfer matrix method and is applied to simulate the properties of such a device. Competition and interference of the dual modes in the resonator lead to dual-band filtering with high isolation. As the finite-difference time-domain simulation illustrates, two low-order resonant modes can be effectively triggered by optimizing the waveguide width and spacing gap between the compact resonator and waveguides. In experiment, a double side-coupled microdisk resonator was fabricated on a nanophotonic silicon-on-insulator platform, and dual-band bandpass filtering is realized with an optical isolation higher than 20 dB and an insertion loss lower than 2 dB. The experimental results agree well with our modeling results.     

Double Stage Flat Passband Acousto-Optic Wavelength Filter

We developed a flat passband acoustooptic filter. For the passband flattening, cascaded bandpass and notch filters with different mode converter lengths and conversion strengths were used. We attained a flat passband with flatness of less than 1 dB in the 2 nm range using the device with a second- to first-stage mode converter length ratio of 1.2.     

微机械FP腔可调谐滤波器在WDM系统中的串扰分析

介绍了一种以FP谐振腔为基础,用于波分复用系统的MOEMS器件-电控可调谐FP光滤波器.器件采用微电子机械加工技术研制.研究了FP型解复用器在密集波分复用系统中引入的信道间串扰对系统的影响,并分别讨论了激光器线宽、滤波器带宽、信道间距对串扰的影响.在信道间隔为100GHz,激光器线宽为5GHz,串扰可达到-21dB左右.     

Lumped-equivalent circuit model for multi-stage cascaded magnetoelectric dual-tunable bandpass filter

A lumped-equivalent circuit model of a novel magnetoelectric tunable bandpass filter, which is realized in the form of multi-stage cascading between a plurality of magnetoelectric laminates, is established in this paper for convenient analysis.The multi-stage cascaded filter is degraded to the coupling microstrip filter with only one magnetoelectric laminate and then compared with the existing experiment results. The comparison reveals that the insertion loss curves predicted by the degraded circuit model are in good agreement with the experiment results and the predicted results of the electromagnetic field simulation, thus the validity of the model is verified. The model is then degraded to the two-stage cascaded magnetoelectric filter with two magnetoelectric laminates. It is revealed that if the applied external bias magnetic or electric fields on the two magnetoelectric laminates are identical, then the passband of the filter will drift under the changed external field; that is to say, the filter has the characteristics of external magnetic field tunability and electric field tunability. If the applied external bias magnetic or electric fields on two magnetoelectric laminates are different, then the passband will disappear so that the switching characteristic is achieved. When the same magnetic fields are applied to the laminates, the passband bandwidth of the two-stage cascaded magnetoelectric filter with two magnetoelectric laminates becomes nearly doubled in comparison with the passband filter which contains only one magnetoelectric laminate. The bandpass effect is also improved obviously. This research will provide a theoretical basis for the design, preparation, and application of a new high performance magnetoelectric tunable microwave device.     

Tunable and reconfigurable photonic microwave filter based on stimulated Brillouin scattering

A high Q-factor photonic microwave filter showing tuning and reshaping capabilities and based on stimulated Brillouin scattering is demonstrated. The filter bandpass can be continuously tuned, changing the microwave oscillator used to generate the pump power, and the filter shape can be modified by modulating the microwave tone. A single bandpass over the microwave spectrum can be obtained by using single-sideband suppressed carrier modulation. Experimental results demonstrate the wide tuning range of the filter, its reshaping capability, and Q factor of 670.     

Integrated optical filter arrays fabricated by using the combinatorial etching technique

A combinatorial etching technique is developed to fabricate integrated narrow bandpass filters on a single substrate. It is highly efficient for fabrication of integrated filter arrays in optical regions. A monolithic filter array has been fabricated by using the technique with a two-step deposition process. The filter contains 32 elements in the near-infrared region. The relative full width at half-maximum (FWHM) sigmalambda/lambda of the filter elements is less than 0.2%. Such a narrow bandpass filter array can be utilized in many optical applications.