Flow-injection spectrophotometric determination of methyldopa in pharmaceutical formulations

A flow-injection spectrophotometric procedure is proposed for methyldopa determination in pharmaceutical preparations. The determination is based on formation of a yellow product (measured at 410 nm) after complexation of methyldopa with molybdate. Under optimal conditions, Beer's law is obeyed in a concentration range of 50-200 mg l⁻¹ methyldopa. Typical correlation between absorbance and analyte concentration was 0.9999. Usual excipients used as additives in pharmaceuticals do not interfere with the proposed method. The analytical frequency was 210 h⁻¹ and the relative standard deviation (R.S.D.) was ≤2% for sample solution containing 150 mg l⁻¹ methyldopa (n = 11). The analytical results obtained in commercial formulations by applying the proposed FIA method were in good agreement with labeled values and those obtained by the Brazilian Pharmacopoeia procedure at 95% confidence level.     

Selective spectrophotometric determination of phenolic β-lactam antibiotics in pure forms and in their pharmaceutical formulations

Four simple and selective spectrophotometric methods were developed for the quantitative determination of some phenolic β-lactam antibiotics (amoxicillin trihydrate, cefoperazone sodium, cefadroxil monohydrate, and cefprozil anhydrous) in pure forms as well as in their pharmaceutical formulations through their nitration and subsequent complexation with an nucleophilic reagent (method I), nitrosation and subsequent metal chelation (method II), coupling with diazo reagent (method III), and reaction with copper and extraction of the resulting chelate into chloroform (method IV). The reaction conditions were studied and optimized. Beer’s plots were obeyed in a general concentration range of 5-30 ug ml⁻¹ with correlation coefficients not less than 0.9997 for the four drugs. The methods are successfully applied to the analysis of pharmaceutical formulations containing amoxicillin, either alone or in combination with potassium clavulanate. They were also applied to the analysis of the other three studied drugs in vials, capsules, tablets, and suspensions with good recovery; percentage ranged from 99.0 (±1.42) to 100.2 (±1.25) in method I, 99.0 (±0.82) to 100.5 (±0.92) in method II, 99.5 (±0.09) to 100.8 (±0.98) in method III, and 99.3 (±0.01) to 100.2 (±0.05) in method IV. Interferences from other antibiotics and additives were investigated.     

Four spectrophotometric methods for determination of nitrofurazone in pharmaceutical formulations

Four simple and sensitive visible spectrophotometric methods (A-D) for the determination of nitrofurazone in bulk samples and pharmaceutical formulations are described. They are based on the formation of colored species by treating either its reduction product with 3-methylbenzothiazolin-2-one hydrazone in the presence of ferric chloride (method A: _max 600 nm) or its hydrolysis product with thiobarbituric acid (method B: _max 520 nm, 440 nm) or barbituric acid (method C: _max 400 nm) or by oxidizing it with excess N-bromosuccinimide and determining the consumed NBS using metol-isonicotinic acid hydrazide (method D: _max 620 nm).     

Enzymatic determination of vitamin A in pharmaceutical formulations with spectrophotometric detection

An enzymatic method for the determination vitamin A (retinol) is reported using soluble and immobilized alcohol dehydrogenase, isolated from rabbit liver. The reaction is based on the oxidation of retinol and simultaneous reduction of NAD⁺ to NADH followed by spectrophotometric detection at 340 nm. The calibration graph was linear over the range of 2.0–10 μM with correlation coefficients of 0.9967 and 0.9992 (n = 5) for soluble and immobilized alcohol dehydrogenase respectively, with relative standard deviations (n = 3) in the range of 0.5–1.2%. The limit of detection was lower than 1.0 μM. The proposed method was applied to determine vitamin A in pharmaceuticals, and the results obtained were in reasonable agreement with the amount labeled. The results were compared using spectrophotometric reference method, and no significant difference was found between the results of the both methods.     

Indirect spectrophotometric determination of diltiazem hydrochloride in pure form and pharmaceutical formulations

Three simple, accurate, and sensitive spectrophotometric methods (A, B and C) have been described for the indirect assay of diltiazem hydrochloride (DIL.HCl), either in pure form or in pharmaceutical formulations. The first method (A) is based on the oxidation of DIL.HCl by N-bromosuccinimide (NBS) and determination of unconsumed NBS by measuring the decrease in absorbance of amaranth dye (AM) at a suitable λ _max =521 nm. Other methods (B) and (C) involve the addition of excess cerric ammonium sulfate (CAS) and subsequent determination of the unconsumed oxidant by a decrease in the red color of chromotrope 2R (C2R) at a suitable λ _max =528 nm or a decrease in the orange-pink color of rhodamine 6G (Rh6G) at λ _max =525 nm, respectively. Regression analysis of Beer-Lambert plots showed good correlation in the concentration ranges 3.0–9.0, 3.5–7.0 and 3.5–6.3 μg ml⁻¹ for methods A, B and C, respectively. The apparent molar absorptivity, Sandell's sensitivity, detection and quantification limits were calculated. The proposed methods have been applied successfully for the analysis of the drug in its pure form and its dosage form. No interference was observed from a common pharmaceutical adjuvant. Statistical comparison of the results with the reference method shows excellent agreement and indicates no significant difference in accuracy and precision.     

Kinetic spectrophotometric determination of hyoscine butylbromide in pure form and in pharmaceutical formulations

A simple and sensitive kinetic method was described for the determination of hyoscine butylbromide in pharmaceutical preparations. The method is based upon a kinetic investigation of the oxidation reaction of the drug with alkaline potassium permanganate at room temperature for a fixed time of 15 min. The absorbance of the colored manganate ion was measured at 610 nm. The absorbance–concentration plot was rectilinear over the range of 1.0–10 μg mL^?1 (r = 0.9999) and detection limit of 0.092 μg mL^?1. The concentration of hyoscine butylbromide was calculated using the corresponding calibration equation for the fixed-time method. The determination of hyoscine butylbromide by the fixed-concentration and rate constant methods is also feasible with the calibration equations obtained but the fixed-time method has been found to be more applicable. The different experimental parameters affecting the development and stability of the colors were carefully studied and optimized. The proposed method was applied to the determination of hyoscine butylbromide in pharmaceutical formulations. The results obtained were in good agreement with those obtained using the official British Pharmacopeial method (2004).     

Extractive spectrophotometric determination of fluoroquinolones and antiallergic drugs in pure and pharmaceutical formulations.

A simple, rapid and sensitive spectrophotometric procedure has been proposed for the assay of fluoroquinolones viz., ciprofloxacin (CPF) and norfloxacin (NRF), and antiallergic drugs viz., methdilazine hydrochloride (MDH) and isothipendyl hydrochloride (IPH) in bulk and pharmaceutical formulations. The method is based on the reaction of selected drugs with Brilliant Blue G (BBG) in NaOAc-AcOH buffer of pH 4.0 for CPF and NRF or in neutral medium for MDH and IPH to give chloroform soluble ion-association complexes. The effects of various parameters have been studied. The ion-association complexes exhibited absorption maxima at 610 nm for CPF, at 614 nm for NRF and MDH, and at 612 nm for IPH. Beer's law plots were obeyed in the concentration ranges of 0.5-6.0, 0.4-8.0, 0.1-6.0 and 0.2-6.1 (mg ml(-1) for CPF, NRF, MDH and IPH, respectively, with correlation coefficients not less than 0.9969. Molar absorptivity values as calculated from the Beer's law data were found to be 2.86 x 10(4), 2.64 x 10(4), 3.13 x 10(4) and 5.51 x 10(4) mol(-1) cm(-1) for CPF, NRF, MDH and IPH, respectively. The influence of commonly employed excipients in the determination of the studied drugs has been studied. The results obtained by the proposed method were statistically validated.     

Indirect spectrophotometric determination of propranolol hydrochloride and piroxicam in pure and pharmaceutical formulations.

Two simple and sensitive indirect spectrophotometric methods for the assay of propranolol hydrochloride (PPH) and piroxicam (PX) in pure and pharmaceutical formulations have been proposed. The methods are based on the oxidation of PPH by a known excess of standard N-bromosuccinimide (NBS) and PX by ceric ammonium sulfate (CAS) in an acidic medium followed by the reaction of excess oxidant with promethazine hydrochloride (PMH) and methdilazine hydrochloride (MDH) to yield red-colored products. The absorbance values decreased linearly with increasing concentration of the drugs. The systems obeyed Beer's law over the concentration ranges of 0.5 - 12.5 and 0.3 - 16.0 microg/ml for PPH, and 0.4 - 7.5 and 0.2 - 10 microg/ml for PX with PMH and MDH, respectively. Molar absorptivity values, as calculated from Beer's law data, were found to be 1.36 x 10(4) and 2.55 x 10(4) l mol(-1) cm(-1) for PPH, and 2.08 x 10(4) and 2.05 x 10(4) l mol(-1) cm(-1) for PX with PMH and MDH, respectively. The common excipients and additives did not interfere with their determinations. The proposed methods have been successfully applied to the determinations of PPH and PX in various dosage forms. The results obtained by the proposed methods compare favorably with those of official methods.     

Novel microwell-based spectrophotometric assay for determination of atorvastatin calcium in its pharmaceutical formulations

The formation of a colored charge-transfer (CT) complex between atorvastatin calcium (ATR-Ca) as a n-electron donor and 2, 3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ) as a π-electron acceptor was investigated, for the first time. The spectral characteristics of the CT complex have been described, and the reaction mechanism has been proved by computational molecular modeling. The reaction was employed in the development of a novel microwell-based spectrophotometric assay for determination of ATR-Ca in its pharmaceutical formulations. The proposed assay was carried out in 96-microwell plates. The absorbance of the colored-CT complex was measured at 460 nm by microwell-plate absorbance reader. The optimum conditions of the reaction and the analytical procedures of the assay were established. Under the optimum conditions, linear relationship with good correlation coefficient (0.9995) was found between the absorbance and the concentration of ATR-Ca in the range of 10-150 μg/well. The limits of detection and quantitation were 5.3 and 15.8 μg/well, respectively. No interference was observed from the additives that are present in the pharmaceutical formulation or from the drugs that are co-formulated with ATR-Ca in its combined formulations. The assay was successfully applied to the analysis of ATR-Ca in its pharmaceutical dosage forms with good accuracy and precision. The assay described herein has great practical value in the routine analysis of ATR-Ca in quality control laboratories, as it has high throughput property, consumes minimum volume of organic solvent thus it offers the reduction in the exposures of the analysts to the toxic effects of organic solvents, and reduction in the analysis cost by 50-fold. Although the proposed assay was validated for ATR-Ca, however, the same methodology could be used for any electron-donating analyte for which a CT reaction can be performed.     

Sensitive extractive spectrophotometric methods for the determination of nortriptyline hydrochloride in pharmaceutical formulations

Two simple, sensitive and rapid extractive spectrophotometric methods have been developed for the assay of the antidepressant drug nortriptyline (NOR) hydrochloride in pure form and in different dosage forms. The methods involve the formation of colored ion-pairs between the drug and the complex of niobium(V)-thiocyanate (Nb-SCN) or iron(III)-thiocyanate (Fe-SCN) followed by their extraction with butanol or a mixture of butanol and chloroform and quantitative determination at 360 nm and 490 nm, using Nb-SCN and Fe-SCN, respectively. The experimental conditions were optimized to obtain the maximum colour intensity. The methods permit the determination of nortriptyline over a concentration range of 15-100 microg/ml and 5-24 microg/ml with the detection limit of 0.84 microg/ml and 0.32 microg/ml, using Nb-SCN and Fe-SCN, respectively. The proposed methods are applicable for the assay of the investigated drug in different dosage forms and the results are in good agreement with those obtained by the official and HPLC methods. No interference was observed from common excipients present in pharmaceutical formulations. The proposed procedures were applied to determine the amount of nortriptyline hydrochloride as active ingredient in the presence of its degradation product, dibenzosuberone. The extractive spectrophotometric methods can also be used to determine the amount of nortriptyline hydrochloride in tablets after its solid phase extraction (SPE).     

Indirect flow-injection spectrophotometric determination of meloxicam, tenoxicam and piroxicam in pharmaceutical formulations.

A simple and sensitive indirect spectrophotometric method for the assay of meloxicam (MX), tenoxicam (TX) and piroxicam (PX) in pure and in pharmaceutical formulations by flow injection analysis (FIA) has been proposed. The method is based on the oxidation of these drugs by a known excess of N-bromosuccinimide (NBS) in an acidic medium, followed by a reaction of excess oxidant with chloranilic acid (CAA) to bleach its purple color. The absorbance values increased linearly with increasing concentrations of the drugs. Variables, such as the acidity, reagent concentrations, flow rate of reagents and other FI parameters were optimized to produce the most sensitive and reproducible results. The system obeyed Beer's low over concentration ranges of 10 - 160, 20 - 200 and 10 - 160 microg/ml for MX, TX and PX, respectively. The common excipients and additives did not interfere with their determinations. The method was successfully applied to the determinations of MX, TX and PX in various pharmaceutical preparations. The results obtained by the proposed method were found to be in good agreement with those found by the official HPLC methods.     

Combined microwave-assisted isolation and solid-phase purification procedures prior to the chromatographic determination of phenolic compounds in plant materials

A fast, sensitive and selective procedure employing a combination of microwave-assisted extraction (MAE) and solid phase extraction (SPE) was applied prior to liquid chromatographic identification and quantification of phenolic compounds in plant materials. MAE has been tested and optimized for the isolation of phenolic acids (gallic, protocatechuic, p-hydroxybenzoic, chlorogenic, vanilic, caffeic, syringic, p-coumaric, ferulic, sinapic, benzoic, m-coumaric, o-coumaric, rosmarinic, cinnamic acids) and 3,4-dihydroxybenzaldehyde, syringaldehyde, p-hydroxybenzaldehyde, and vanillin in various plants. The effects of experimental conditions on MAE efficiency, such as solvent composition, temperature, extraction time, have been studied. The extraction efficiencies were compared with those obtained by computer-controlled, two-step Soxhlet-like extractions. Plant extracts were purified and phenolic compounds were pre-concentrated using SPE on polymeric RP-105 SPE sorbent prior to HPLC analysis. Chromatographic separation was carried out on a Hypersil BDS C₁₈ column using a mobile phase consisted of 0.3% (v/v) acetic acid in water (solvent A) and methanol (solvent B) at flow rate 0.6 ml min⁻¹ and column temperature 30 °C with gradient elution.     

Validated spectrophotometric method for quantitative determination of simvastatin in pharmaceutical formulations and human serum

A simple ultraviolet spectrophotometric method for the determination of simvastatin in methanol has been devised and compared with the existing pharmacopoeial RP-HPLC method for the estimation of the drug. Analytical parameters such as stability, selectivity, accuracy, and precision have been established for the method, using SIMS® tablets and human serum samples, and evaluated statistically to assess the application of the method. The method was validated under ICH and USP guidelines and was found to comprise the advantages for simplicity, stability, sensitivity, reproducibility, and accuracy for use as an alternative to existing nonspectrophotometric methods for the routine determination of the drug in pharmaceutical formulations and for pharmaceutical investigations involving simvastatin.     

Sensitive extractive spectrophotometric methods for the determination of trazodone hydrochloride in pharmaceutical formulations

Two simple, rapid and sensitive extractive spectrophotometric methods have been developed for the assay of trazodone hydrochloride (TRH) in pure and pharmaceutical formulations. These methods are based on the formation of chloroform soluble ion-association complexes of TRH with bromothymol blue (BTB) and with bromocresol purple (BCP) in KCl-HCl buffer of pH 2.0 (for BTB) and in NaOAc-AcOH buffer of pH of 3.6 (for BCP) with absorption maximum at 423 nm and at 408 nm for BTB and BCP, respectively. Reaction conditions were optimized to obtain the maximum color intensity. The absorbance was found to increase linearly with increase in concentration of TRH, which was corroborated by the calculated correlation coefficient values (0.9996, 0.9945). The systems obeyed Beer's law in the range of 0.2-14.5 and 0.2-14.1 microg/ml for BTB and BCP, respectively. Various analytical parameters have been evaluated and the results have been validated by statistical data. No interference was observed from common excipients present in pharmaceutical formulations. The proposed methods are simple, accurate and suitable for quality control applications.     

Two charge-transfer complex spectrophotometric methods for the determination of sulpiride in pharmaceutical formulations

Two simple, rapid, accurate and sensitive spectrophotometric methods are described for the determination of sulpiride. They are based on charge transfer complexation between the drug as n-electron donor and p-chloranilic acid as π acceptor or iodine as σ-acceptor. These give highly coloured complexes with absorption maxima at 518 and 363, 294 nm, respectively. Beer’s law linear ranges were 13.7–341.4 and 1.7–20.5 µg mL^?1 for the p-chloranilic acid and iodine methods. The methods were successfully applied to the determination of the drug in Dogmatil® Fort tablets and the results compared with the official method. The complex association constants and standard free energy changes were calculated using Benesi-Hildebrand plots.      

Kinetic spectrophotometric methods for the determination of alfuzosin hydrochloride in bulk and pharmaceutical formulations

Simple and sensitive kinetic spectrophotometric methods were established for the determination of alfuzosin hydrochloride in bulk and in its pharmaceutical preparations using alkaline potassium permanganate as an oxidizing agent. The methods involve determination of alfuzosin HCl by kinetic studies of its oxidation at room temperature for a fixed time of 15 min. The absorbance of the colored manganate ions was measured at 610 nm. Alternatively, the decrease in the absorbance of permanganate upon addition of the studied drug was also measured at 525 nm. The absorbance-concentration plots in both procedures were rectilinear over the range of 2.0–30.0 μg/mL. The different experimental parameters affecting the development were carefully studied and optimized. The determination of alfuzosin HCl by the fixed concentration and initial rate methods is also feasible with the calibration equations obtained but the fixed time method has been found to be more applicable. Both procedures were applied to the determination of alfuzosin HCl in formulations. The results obtained were in good agreement with those obtained using reference methods.     

Validated kinetic spectrophotometric method for the determination of metoprolol tartrate in pharmaceutical formulations

A kinetic spectrophotometric method has been described for the determination of metoprolol tartrate in pharmaceutical formulations. The method is based on reaction of the drug with alkaline potassium permanganate at 25+/-1 degrees C. The reaction is followed spectrophotometrically by measuring the change in absorbance at 610 nm as a function of time. The initial rate and fixed time (at 15.0 min) methods are utilized for constructing the calibration graphs to determine the concentration of the drug. Both the calibration graphs are linear in the concentration range of 1.46 x 10(-6)-8.76 x 10(-6) M (10.0-60.0 microg per 10 ml). The calibration data resulted in the linear regression equations of log (rate)=3.634+0.999 log C and A=6.300 x 10(-4)+6.491 x 10(-2) C for initial-rate and fixed time methods, respectively. The limits of quantitation for initial rate and fixed time methods are 0.04 and 0.10 microg ml(-1), respectively. The activation parameters such as E(a), DeltaH(double dagger), DeltaS(double dagger) and DeltaG(double dagger) are also evaluated for the reaction and found to be 90.73 kJ mol(-1), 88.20 kJ mol(-1), 84.54 J K(-1) mol(-1) and 63.01 kJ mol(-1), respectively. The results are validated statistically and through recovery studies. The method has been successfully applied to the determination of metoprolol tartrate in pharmaceutical formulations. Statistical comparison of the results with the reference method shows excellent agreement and indicates no significant difference in accuracy and precision.     

Normal and differential demasking flow-injection manifold for the direct spectrophotometric determination of zinc(II) in biological materials and pharmaceutical formulations

A normal and a differential demasking flow-injection (FI) manifold were developed and optimized for the spectrophotometric determination of microamounts of Zn(II) in biological materials and pharmaceutical formulations. The reported method is very sensitive, rapid, simple and it is based upon the reaction of Zn(II) with 2,2'-dipyridyl-2-pyridylhydrazone (DPPH) in a strongly basic medium to form a yellow-coloured complex (lambda max = 448 nm). By using the differential demasking manifold, the tolerance of the method to many cations was enhanced by a mean factor of 25. The obtained calibration graphs were linear in the range of 0-10 mg l-1 Zn(II), at a sampling rate of 120 injections h-1 in both cases. The precisions of both manifolds were very good (RSD = 0.6 and 0.8%, respectively) and the 3 sigma detection limits were quite satisfactory (cL = 4 and 6 ng ml-1 respectively). The method has been successfully applied to the determination of Zn(II) in serum, human hair and pharmaceutical formulations with recoveries ranging between 98.0 and 101.6%. The obtained results were also in excellent agreement with flame atomic absorption spectrometry (FAAS), since the mean relative error was er = 0.9%.     

Validation of UV spectrophotometric and nonaqueous titration methods for the determination of carvedilol in pharmaceutical formulations

Ultraviolet (UV) spectrophotometric and nonaqueous volumetric methods are described for the determination of carvedilol in pharmaceutical formulations. Linearity, precision, and accuracy were evaluated according to the validation guidelines of the International Conference on Harmonization and the United States Pharmacopeia for both methods. The UV spectrophotometric procedure was performed in ethanol at 244 nm. Good linearity was obtained between 2 and 7 microg/mL with a correlation coefficient of 0.9999. The intra- and interday precision values were <2% for all samples analyzed. The accuracy, determined from recovery studies, was between 97.5 and 102.2%. The other procedure was based on the volumetric quantitation of carvedilol in a nonaqueous medium with 0.01 M perchloric acid and 1% violet crystal as the indicator. The validation of the volumetric method yielded good results that included linearity (r of > 0.999), precision (relative standard deviations of <2% for intra- and interday precision), and accuracy (96.4-102.4%). The methods were applied to tablets and compounded capsules. Statistical analysis by analysis of variance showed no significant difference between the results obtained by the proposed methods.