Coaxial laser cladding on an inclined substrate

This paper describes an experimental and theoretical study of the cladding mode of coaxial laser cladding on an inclined substrate. Based on the image analysis of the powder stream and clad profile measurements in coaxial laser cladding, it was found that irregular clad profiles always formed on an inclined surface and the location of the peak profile shifted away from the clad center. This phenomenon is caused by uneven distributions of powder concentration and laser beam intensity. A modified Gaussian mode for powder stream and laser beam was proposed to estimate the clad profiles on an inclined plane under laser beam irradiation. The effects of the inclined steel substrate on the CO₂ laser beam absorption and stainless-steel powder catchment were examined experimentally. The results show that both the laser absorption and the powder catchment on the mild steel decrease with increasing the cladding angle. From the analysis of laser beam mode, the clad width is equivalent to the beam spot size on the inclined substrate. However, the clad height correlates well with the distribution of the powder concentration. The results show that the Gaussian cladding mode could be adopted in various laser cladding applications such as rapid prototyping and butt welding to predict the clad profiles precisely.     

送粉角度对激光熔覆铁基复合涂层形状特征的影响

通过分析激光熔覆过程中光束、粉末和熔池间的作用机理,建立了送粉式激光熔覆材料有效利用率的数学模型,在此基础上推导了送粉角度与工艺参数之间的定量关系式,并计算了不同送粉角度下的熔覆材料有效利用率、熔高和横截面积。结果表明,在熔覆工艺参数不变的条件下,理论计算的熔覆材料有效利用率、熔覆层高度和横截面积均随送粉角度的增加而增大,且均高于实验检测值。激光熔覆过程中,由于粉末烧损和机械损失,使熔覆材料有效利用率、熔高和横截面积随送粉角度变化出现最大值,理想送粉角度为60。     

Effects of process variables on laser direct formation of thin wall

In this paper, effects of process variables on wall thickness, powder primary efficiency and speed of forming a thin metallic wall in single-pass coaxial laser cladding are investigated, and some resolution models are established and testified experimentally. With some assumptions, each of wall thickness, powder primary efficiency and formation speed can be defined as a function of the process variables. Wall thickness is equal to width of the molten pool created in single-pass laser cladding and determined by laser absorptivity, laser power, initial temperature, scanning speed and thermo-physical properties of clad material. Powder primary efficiency and formation speed are both dependent on an exponential function involving the ratio of melt pool width, which is decided by the process variables, to powder flow diameter. In addition, formation speed is influenced by powder feed rate. In present experiment, a 500 W continual-wave (CW) CO₂ laser is used to produce thin-wall samples by single-pass coaxial laser cladding. The experimental results agree well with the calculation values despite some errors.     

Analysis and prediction of single laser tracks geometrical characteristics in coaxial laser cladding process

Direct Laser Fabrication is a promising new manufacturing technology coming from laser cladding process. From a coaxial nozzle, powder is fed through a laser beam on a substrate. The powder melting and solidification processes lead to the fabrication of a part layer by layer. In this work 316L stainless steel powder is used to form laser tracks on a low carbon steel substrate. The layer geometry is an important process characteristic to control the final part of fabrication. This paper presents analytical relationships between the laser tracks geometrical characteristics (width, height, area, penetration depth) and the processing parameters (laser power P, scanning speed V and powder mass flow Q_m). Three values of each processing parameters are fixed and so 27 different experiments have been made and analyzed. The validity of these results is discussed studying the correlation coefficient R, the graphical analysis of the residuals and the uncertainty evaluations. Two kinds of models are studied to predict the form and the geometrical characteristics of the single laser tracks cross sections. The first one is an analytical model in which the distribution of the powder in the feed jet is supposed to govern the laser clad geometry. Three distributions are proposed: Gaussian, uniform and polynomial. In the second model the general form of the clad cross section is supposed to be a disk due to the surface tension forces. Analytical relationships are established between the radius and the center of the disk in one hand and the process parameters in the other hand. This way we show that we can reproduce the laser track geometry in all the area experimentally explored.     

Numerical simulation of powder transport behavior in laser cladding with coaxial powder feeding

Laser cladding with coaxial powder feeding is one of the new processes applied to produce well bonding coating on the component to improve performance of its surface. In the process, the clad material is transported by the carrying gas through the coaxial nozzle, generating gas-powder flow. The powder feeding process in the coaxial laser cladding has important influence on the clad qualities. A 3D numerical model was developed to study the powder stream structure of a coaxial feeding nozzle. The predicted powder stream structure was well agreed with the experimental one. The validated model was used to explore the collision behavior of particles in the coaxial nozzle, as well as powder concentration distribution. It was found that the particle diameter and restitution coefficient greatly affect the velocity vector at outlet of nozzle due to the collisions, as well as the powder stream convergence characteristics below the nozzle. The results indicated a practical approach to optimize the powder stream for the coaxial laser cladding.     

Study on cross-section clad profile in coaxial single-pass cladding with a low-power laser

In this paper, a model of cross-section clad profile on the substrate in coaxial single-pass cladding with a low-power laser was studied. The static model of powder mass concentration distribution at cold-stream conditions was defined as a Gaussian function. In coaxial single-pass cladding with a low-power laser, since the influence of surface tension, gravity and gas flow on the clad bead could be neglected, the cross-section profile of the clad bead deposited by a low-power laser on the substrate was dominated by the powder concentration at each point on the pool and the time when the material was liquid at this point. The height of each point on the cross-section clad profile was defined as a definite integration of a Gaussian function from the moment at which the melt pool was just arriving at the point to the moment at which the point left the melt pool. In the presented experiment, powder of Steel 63 (at 0.63 wt% C) was deposited on a substrate of Steel 20 (at 0.20 wt% C) at the laser power of 135 W. The experimental results testified the model.     

3-D finite element modeling of laser cladding by powder injection: effects of laser pulse shaping on the process

This paper introduces a 3-D transient finite element model of laser cladding by powder injection to investigate the effects of laser pulse shaping on the process. The proposed model can predict the clad geometry as a function of time and process parameters including laser pulse shaping, travel velocity, laser pulse energy, powder jet geometry, and material properties. In the proposed strategy, the interaction between powder and melt pool is assumed to be decoupled and as a result, the melt pool boundary is first obtained in the absence of powder spray. Once the melt pool boundary is obtained, it is assumed that a layer of coating material is deposited on the intersection of the melt pool and powder stream in the absence of the laser beam in which its thickness is calculated based on the powder feedrate and elapsed time. The new melt pool boundary is then calculated by thermal analysis of the deposited powder layer, substrate and laser heat flux. The process is simulated for different laser pulse frequencies and energies. The results are presented and compared with experimental data. The quality of clad bead for different parameter sets is experimentally evaluated and shown as a function of effective powder deposition density and effective energy density. The comparisons show excellent agreement between the modeling and experimental results for cases in which a high quality clad bead is expected.     

Effects of processing parameters on structure of Ni-based WC composite coatings during laser induction hybrid rapid cladding

The relationships between the processing parameters (i.e. laser specific energy, powder density, preheated temperature of substrate and types of substrate) and the structure characteristics of Ni-based WC composite coatings during laser induction hybrid rapid cladding (LIHRC) were investigated systematically. The results show that laser specific energy, cladding height and contact angle have a linear relation with powder density, as can provide the predictions of laser processing parameters according to the geometrical characteristics of a single laser track (i.e. cladding height, cladding width). Moreover, dilution of composite coating increases with the increasing of laser specific energy and the preheated temperature of substrate, while reduces with the increasing of powder density. The types of substrate also have an important effect on dilution of composite coating, as has a strong dependence on the thermophysical properties of substrate (i.e. melting point, resistivity and permeability).     

激光熔覆中金属粉末粒子与激光相互作用模型

为了对同轴激光熔覆过程中运动的金属粉末粒子的速度和温度进行理论分析,并研究各工艺参量的影响,建立了运动中金属粉末粒子的运动模型和热模型.模拟结果表明,粉嘴几何尺寸、粒子直径以及气/粉两相流初始速度是影响粒子运动行为的重要因素;粉嘴几何尺寸、激光焦点位置、激光发散角、激光功率、粒子直径以及气/粉两相流初始速度是影响粒子热行为的重要因素.在相同的工艺参量下(粉嘴出口内径r=2 mm,粉嘴倾角α=60°,初始气流速度v0=0.8 m/s),基于数字粒子图像测速(DPIV)技术,对316L不锈钢粉末粒子运动模型进行了实验验证.结果表明,运动理论模型是可靠的.该模型是掌握同轴激光熔覆过程中金属粉末粒子运动行为的有效工具;同时,热模型也是分析粉末粒子温度随不同参量变化的重要工具.     

An in-process method for the inverse estimation of the powder catchment efficiency during laser cladding

An estimation of the heat loss by conduction can be obtained from measurements of the surface temperature and an overall heat balance at the clad laser interaction zone. Through an inverse calculation of the boundary temperature from observed surface temperatures the powder catchment efficiency can be estimated along with the variation in the clad height expected during laser cladding. This method shows a possible way to monitor and control the clad height and profile as required by near net shape manufacturing methods based on laser cladding.     

激光感应复合熔覆的稀释率分析模型及实验研究

在分析计算感应加热温度模型和激光感应复合熔覆能量作用的基础上,推导出了激光感应复合熔覆稀释率的表达式,定量反映了稀释率与激光、感应能量、材料特性和工艺参数之间的关系,并且通过实验进行了验证。研究结果表明：复合熔覆的稀释率随激光功率的增加而增大,随送粉率的增加而减小,随扫描速度的增大而减小;在其他参数恒定,感应能量增加时,稀释率显著增大。该稀释率分析模型有助于复合熔覆加工中稀释率的控制,为复合熔覆工艺参数的优化设计和熔覆层的质量控制提供了理论基础。     

Numerical simulation of temperature distribution and TiC growth kinetics for high power laser clad TiC/NiCrBSiC composite coatings

A three dimensional model was proposed to simulate high power laser clad TiC/NiCrBSiC composite coatings on Ti6Al4V alloys. The temperature distribution, temperature curves on different nodes, three dimensional shape and size of TiC melting region, molten pool and heat affected zone (HAZ) of the substrate were obtained. To have a clear physical insight into the phase transformation and microstructure evolution in the coatings during laser cladding process, a theoretical kinetic analysis was performed to elucidate the nucleation, growth velocity, and size of TiC particles on the basis of simulated temperature curves of the molten pool. A good quality TiC/NiCrBSiC composite coating with low dilution rate and excellent metallurgical bond was fabricated under optimal processing parameters using powder mixture of TiC and NiCrBSiC as clad material and cuboid of Ti6Al4V alloys as substrate. To validate the reliability of the proposed model, the theoretical results were compared with the microstructure of the coatings. It shows that these theoretical results are in excellent agreement with the experiment cases.     

Microstructure of Bonding Zones in Laser Clad TiC-reinforced Coating

１ＩｎｔｒｏｄｕｃｔｉｏｎＬａｓｅｒｃｌａｄｄｉｎｇｏｆｃａｒｂｉｄｅｍｅｔａｌｃｏｍｐｏｓｉｔｅｃｏａｔｉｎｇｓｉｓａｐｒｏｍｉｓｉｎｇｔｅｃｈｎｏｌｏｇｙｆｏｒｍａｎｕｆａｃｔｕｒｉｎｇｗｅａｒｒｅｓｉｓｔａｎｔｓｕｒｆａｃｅｌａｙｅｒｓｆｏｒ...     

Clad profiles in edge welding using a coaxial powder filler nozzle

The powder catchment and clad profile of the edge welding were investigated by experimental and numerical approaches in this study. The clad profile on the edges joined by a coaxial powder filler nozzle with a CO₂ laser was measured and compared with the powder concentration mode, which was confirmed by powder flow visualization and numerical computations.In the numerical simulation of an impinging jet of gas-powder flow on an edge joint, the powder concentration distributed on a V groove joined by two plates was solved by FLUENT software. Based on the Gaussian mode of the powder distribution in the jet flow, a simplified mode function was proposed to estimate the clad profiles in the edge joint.Cladding experiments were performed for mild steel substrates with thicknesses of 2 and 6 mm under 1 kWCO₂ laser irradiation for 304L stainless steel powder. The results show that the concave clad profiles were generated at large incline angles and the powder catchment efficiency might increase with the joint angle and substrate thickness.Based on the analytical results of the cold powder streams impinging on the edge joint, the similarity between the clad profile and the powder concentration in the edge joint is retained only at small incline angles for thin substrates. Due to the heating effects of laser beam spot and the powder re-distribution inside the edge joint, the deviation of the clad profile between the computation and experiment is increased with the incline angle and substrate thickness.     

Numerical investigation of the microstructure of a clad layer produced via laser cladding with coaxial metal powder injection

The microstructure of a clad layer produced via selective laser cladding with coaxial metal powder injection is studied numerically. The Johnson–Mehl–Avrami–Kolmogorov equation for condensed systems with inhomogeneous rates of nucleation is used to model the phase change kinetics. The impact of the substrate boundary along with interconnected heat transfer and phase change processes on the final microstructure of a built-up layer is demonstrated. The qualitative difference between the behavior of the temperature on the built-up layer’s surface and at the depth of the substrate is established, revealing the inhomogeneous microstructure of the final layer.     

Nd : YAG laser cladding of marine propeller with hastelloy C-22

Nd:YAG laser cladding with automatic wire feeding (Hastelloy C-22) has been done to increase the lifetime of marine propellers made of HBsC1. The effects of processing parameters on the quality of clad layer have been investigated and clad layers have analyzed by optical microscopy and Vickers hardness tester. The method to overcome the drop transfer problem during the wire feeding has been introduced. A cladding speed that is too fast or too slow influenced the shape of clad. The good clad layer without cracks and with low dilution has been obtained with the optimum processing parameters . PACS 81.20.Vj; 42.62.Cf; 81.20.Wk     

Wear resistance of laser cladding and plasma spray welding layer on stainless steel surface

The effect of coatings, which are formed with laser cladding and plasma spray welding on 1Cr18Ni9Ti base metal, on wear resistance is studied, A 5-kW transverse flowing CO2 laser is used for cladding Co base alloy powder pre-placed on the substrate. Comparing with the plasma spray coatings, the spoiled rate of products with laser clad layers was lower and the rate of finished products was higher. Their microstructure is extremely fine. They have close texture and small size grain. Their dilution resulting from the compositions of the base metal and thermal effect on base metal are less. The hardness, toughness,and strength of the laser cladding layers are higher. Wear tests show that the laser layers have higher properties of anti-friction, anti-scour and high-temperature sliding strike. The wear resistance of laser clad layers are about one time higher than that of plasma spray welding layer.     

In-time motion adjustment in laser cladding manufacturing process for improving dimensional accuracy and surface finish of the formed part

This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish.     

Plunging method for Nd : YAG laser cladding with wire feeding

The effects of wire feeding direction and position, cladding time, and cladding speed on the quality of cladding layer for laser cladding with wire feeding are studied. Experiment results indicate that the wire feeding direction and position are important for wire laser cladding. By adopting the correct wire feeding direction and position, the wire can be plunged into the melt pool and can be melted by the heat of the molten metal. With the increase of cladding speed, the dilution of clad layer can be reduced and the growth of the grain size of heat-affected zone of the base metal can be limited. If proper cladding parameters are used, the clad layers will have a good surface shape, sound metallurgical bonding with base metal, low dilution, and the effect of heating on heat-affected zone metal can be limited. The hardness of the clad layer and heat-affected zone are checked. It indicates that with the increase of cladding speed, the hardness of the clad layer and heat-affected zone increases.     

Characterization of dilution action in laser-induction hybrid cladding

Based on an experimental study of laser-induction hybrid cladding by powder feeding, the dilution action and elemental composition distribution were investigated in detail. The results indicate that, compared with individual laser cladding, by using laser-induction hybrid cladding it is easier to form a metallurgical bonding coating and the change range of dilution is much larger. Moreover, at the bottom of molten region, the morphology exhibits nearly a straight line. The processing parameters have great influence on dilution in hybrid cladding. With the increase of scanning speed, the tendency of dilution presents a U-shaped profile, i.e., the middle dilution is much less than those of two ends. The dilution increases with the induction energy. Furthermore, the bigger the dilution, the more uniform is the elemental composition throughout coating. In laser-induction hybrid cladding, the microstructure of low dilution coating is relatively fine due to the low hybrid cladding energy. By adjusting the laser energy and induction energy appropriately, i.e., high induction energy—low laser energy, the low dilution coating with fine microstructure and good mechanical properties can be achieved.