Flame Atomic Absorption Spectrometric Determination of Gold and Palladium Using Microcolumn On-line Preconcentration and Separation

A microcolumn on-line preconcentration and separation system was developed for the flame atomic absorption spectrometric (FAAS) determination of trace levels of gold and palladium. The analytes were selectively adsorbed onto the microcolumn packed with 2-mercaptothiazole immobilized silica gel (MBTSG) in an acidity range of 0.1 to 6.0M HCl at a sampling flow rate of 4.0mLmin^–1. The analytes adsorbed could be desorbed by a thiourea solution with a flow rate of 2.0mLmin^–1. Most of the common coexisting metal ions at a concentration of 25.0mgmL^–1 and anions at a concentration of 50.0mgmL^–1 did not interfere with the preconcentration and determination of Au and Pd. The limits of detection (LOD), defined as three times the standard deviation of the blank (3), of Au and Pd are 10ngmL^–1 and 26ngmL^–1, respectively, with a preconcentration time of 60s. The relative standard deviation (RSD) is about 2.0% for 0.20µgmL^–1 Au and 0.30µgmL^–1 Pd. With a sample loading time of 30min, 6.7ngmL^–1 Au and 10ngmL^–1 Pd can be preconcentrated quantitatively. A geological sample, an anode slime and a secondary nickel alloy were successfully determined with the proposed method, and the results obtained showed good agreement with the certified values.Received December 23, 2002; accepted May 14, 2003 Published online August 8, 2003     

Determination of Iron in Tap and Waste Water Using Liquid–Liquid Extraction in a Flow-Injection System

A flow-injection procedure for the determination of iron(III) in water is described. The procedure is based on the formation of an ion pair between the tetraphenylarsonium (Ph₄As⁺) (TPA) or tetrabutylammonium (But₄N⁺) (TBA) cations and the tetrathiocyanatoferrate(III) complex (TTF). This ion pair is extracted with chloroform, and the absorbance of the organic phase is measured at 503nm (for Ph₄As⁺) or 475nm (for But₄N⁺). Iron concentrations higher than 0.9×10^–6molL^–1 (50µgL^–1) can be detected in the first case, with a relative standard deviation of 1.9% (n=12), a linear application rangeof between 1.34 and 54.0×10^–6molL^–1 (75–3015µgL^–1), and a sampling frequency of 30h^–1. For the ion pair with But₄N⁺, the detection limit is 0.52×10^–6molL^–1 (29µgL^–1), with a relative standard deviation of 1.6% and a linear application range between 0.73 and 54.0×10^–6molL^–1. Under the proposed working conditions, only Pd(IV), Cu(II) and Bi(III) interfere. With the application of the merging zones technique, considerable amounts of organic reagent can be saved. The TBA method was applied to the analysis of iron(III) in tap and industrial waste waters.     

Determination of Arsenic in Food Samples by Hydride Generation – Atomic Absorption Spectrometry

A method for the determination of trace amounts of arsenic in food samples using flow injection analysis and atomic absorption spectrometry with hydride generation (FI-HG AAS) was developed. The parameters of the flow injection system and the hydride generation were optimized with respect to reagent concentrations, atomization temperature, injection volume, reaction coil length and carrier flow rate. The limits of detection and quantification were 0.34µgL^–1 and 1.2µgL^–:1, respectively, and the analytical curve is linear up to 30.0µgL^–1 arsenic. The relative standard deviation for 12 replicates varies between 5% for 4.0µgL^–1 As and 1.8% for 30.0µgL^–1 As, with an injection frequency of up to 135h^–1. Interferences from Ni(II), Cu(II), Fe(III), Cr(III), Mo(II), Bi(III), Se(IV), Se(VI), Sb(III) and Sb(V) could be masked with a mixture of ascorbic acid-KI in a 5.0molL^–1 HCl solution. The accuracy of the proposed method was evaluated by using certified reference materials of biological samples, and the method was used to determine the content of arsenic in fish and coffee beans.     

Determination of Na,K, Rb and Cs Distribution in Human Brain Using Neutron Activation Analysis

This study aims to investigate the distribution of Na, K, Rb and Cs in human brains (5 individuals, 12 brain parts, mean age: 75 years). Distribution of the trace metals between lipid fraction and brain tissue was investigated in solvent extraction experiments. Determinations were carried out by instrumental neutron activation analysis. The present results show a rather non-homogeneous distribution for Na and a relatively uniform distribution for K, Rb and Cs. The mean concentrations found are 7440µgNag^–1 dry weight, 12800µgKg^–1, 14µgRbg^–1 and 50ngCsg^–1. A highly significant positive correlation was found between Rb and Cs. Solvent extraction experiments showed that 19% of Rb and 26% of Cs of the total content is located in lipid fraction.     

Determination of Total Selenium Content in Cereals and Bakery Products by Flow Injection Hydride Generation Graphite Furnace Atomic Absorption Spectrometry Applying in-situ Trapping on Iridium-Treated Graphite Platforms

A flow injection hydride generation graphite furnace atomic absorption spectrometric (FI-HG-GFAAS) method was applied to the determination of Se in Se-doped and undoped cereals and bakery products. For the purpose of doping, the soils used for the cultivation of the cereals were dosed with Se-doped foliar fertilizers. The samples were dissolved in a mixture of HNO₃ and H₂O₂ solutions using microwave-assisted digestion. The decomposition of H₂Se generated from the sample solutions and the trapping of elemental Se were performed at a temperature of 300°C on an Ir-pretreated integrated graphite platform of a transversally heated graphite atomizer (THGA). For release of the trapped Se within a fairly short atomization time (5s), an atomization temperature of 2200°C was observed to be optimal. The overall efficiency of hydride generation, transport and trapping was 86%.The upper limit of the linear dynamic range of calibration was 10µgL^–1, which corresponds to 0.5µgg^–1 for solid samples. Recovery of the samples spiked with Se^VI solutions was found to be 93±6% on average. The relative standard deviation of the determinations was less than 8%. The limit of detection was found to be 0.06µgL^–1, corresponding to 3ngg^–1 for solid samples. The accuracy of the method was verified with the use of IAEA-155 (whey powder) certified reference material. End-capped THGA tubes resulted in an extension of the linear calibration range compared to that of standard THGAs.The Se content in bakery products made of undoped cereals ranged from 7.7 to 68ngg^–1 (wet weight) in 18 samples, whereas the Se content of the corresponding cereals was found to be below 100ngg^–1 (wet weight). The Se level of cereals grown on soils treated with Se-doped fertilizers ranged from 128 to 1046ngg^–1 (wet weight), and it depended linearly on the Se concentration of the corresponding foliar fertilizer.     

Determination of Trace Proteins by Rayleigh Light Scattering Technique with Indophenol Blue

The interaction of indophenol blue (IPB) with proteins in aqueous solution has been studied by optical absorption and Rayleigh light scattering (RLS) spectroscopy. At pH 3.8, the weak RLS of IPB is enhanced by proteins. Based on this phenomenon, a novel method for the determination of proteins at nanogram levels using the RLS technique is developed. The method is simple, practical and sensitive. The linear range is 0.25–20.9µgmL^–1 for BSA, and 0.25–17.6µgmL^–1 for HSA. The detection limits (S/N=3) are 23ngmL^–1 for BSA and 22ngmL^–1 for HAS. The results for the determination of proteins in human serum samples are very close to those obtained by an established clinical method. There is very little interference from amino acids, metal ions or other coexisting compounds.     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Determination of Lead Using a New Chromogenic Reagent 2-(2-Sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic Acid

A novel chromogenic reagent, 2-(2-sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid 1, was prepared by diazo coupling of 4-acetylaniline-2-sulfonic acid and 2,4,6-trichloroaniline to chromotropic acid through –N=N– groups. Based on this reagent, a simple, sensitive and selective spectrophotometric method was developed for the determination of lead. In 0.20M phosphoric acid medium, lead reacts with 1 to form a 1:2 blue complex with an absorption maximum of 654nm. Beers law is obeyed in the range of 0–0.6mgL^–1 of lead. The apparent molar absorptivity is 1.25×10⁵Lmol^–1cm^–1. The detection limit and quantification limit were found to be 0.63µgL^–1 and 2.1µgL^–1, respectively. The relative standard deviation for eleven replicate measurements was of 2.6%. The interference of foreign ions was also investigated. All the other foreign ions studied did not interfere with lead determination except for Ca(II) and Ba(II). The interference caused by Ca(II) and Ba(II) can be eliminated by prior extraction of lead with potassium iodide-methylisobutylketone (KI-MIBK). The proposed method was applied to the determination of lead in certified samples with satisfactory results.     

Determination of Chlorine Dioxide Using Capillary On-Line Concentration Coupled with Flow Injection Analysis

A new method for the determination of chlorine dioxide (ClO₂) using capillary (Teflon filter tube) on-line concentration coupled with a flow injection system is proposed. The method is based on the color reaction of 4-aminoantipyrine (4-AAP) with phenol in the presence of ClO₂. The colored product is proportional to the concentration of ClO₂ and can be efficiently concentrated in the Teflon filter tube, following elution and spectrophotometric detection in a flow-through cell. The sensitivity of the method increases about 100 times after concentration. As a result, one of the most sensitive methods of determining ClO₂ (ppb) is obtained. The linear range after concentration is 5–250µg·L^–1 ClO₂. The detection limit is 0.5µg·L^–1. The interferences from other chlorinated compounds and metal ions were eliminated by utilizing gas-phase separation via porous polytetrafluoroethylene (PTFE) membrane for pretreatment.     

In-Situ Separation and Determination of Palladium from Platinum Based on Different Vaporization Temperatures by Electrothermal Vaporization Inductively Coupled Plasma Optical Emission Spectrometry with YPA4 Resin Acting Both as Adsorption Material and Chemical Modifier

A new method has been developed for in-situ separation of Pd from a Pt matrix and determination of trace Pd based on different vaporization temperatures by electrothermal vaporization (ETV) inductively coupled plasma optical emission spectrometry (ICP-OES) with the use of polythioether backbone modified with a diaminoisopropylmercaptane chelating group (YPA₄), both as solid phase extractant and chemical modifier. In 0.5M HNO₃, Pd and Pt can be adsorbed by YPA₄. The resin loaded with Pd and Pt was then prepared to form a slurry that can be directly introduced into the graphite furnace without any pretreatment. The factors affecting in-situ separation of Pd from the Pt matrix were investigated in detail. It was found that, in the presence of YPA₄, Pd could be quantitatively vaporized at lower vaporization temperatures (1800°C–1900°C), while Pt could not be vaporized from the graphite furnace at the same temperature, its quantitative vaporization temperature being 2600°C. Based on the different vaporization temperatures, in-situ separation of Pd from the Pt matrix and determination of trace Pd by ETV-ICP-OES was achieved in the temperature range of 1800°C–1900°C. Under the optimized conditions, the detection limit (3) of Pd is 60pg, and the relative standard deviation (RSD) is 5.6% (n=9, C=0.2µgmL^–1). The method has been applied to the determination of trace Pd in anode slime and Auto Catalyst NIST SRM 2557 reference material, and the determined values coincide with the certified values.     

Magnetic Separation Immunoassay for Digoxin in Plasma with Flow Injection Fluorescence Detection

Immunoassay (IA) is a sensitive and selective approach for low level quantitation of drugs. Magnetic separation immunoassays use magnetic beads to facilitate the separation of bound labeled antigens from free antigens in solution. Digoxin was chosen for this study because low level analysis (ngmL^–1) in biological samples isrequired, antibodies to digoxin were commercially available and derivatization procedures for fluorescence labeling were well established. A competitive immunoassay format was used in this study. Streptavidin coated magnetic beads were attached to biotinylated anti-digoxin antibodies for the separation. The inhibition curve for off-line magnetic separation immunoassay of digoxin in spiked plasma was characterized and the dynamic range of the curve was 0.25–2.5ngmL^–1. A power fit weighted by the inverse of concentration was found to provide the best fit to the data (r=0.9934). The percent RSDs for the two controls, 0.8 and 2.2ngmL^–1, were 9.95% and 20.62% (n=6) and the percent errors were 11.75% and 22.63% (n=6), respectively. The limit of detection (LOD) in plasma is 0.14ngmL^–1. The dynamic range of the inhibition curve for on-line magnetic separation immunoassay of digoxin was 0.5–15ngmL^–1 of digoxin. A quadratic fit was found to provide the best fit to the data (r=0.9937). The percent RSDs for the two controls, 4.0 and 12ngmL^–1, were 14.1% and 10.7% (n=6) and the percent errors were 5.8% and 3.3% (n=6) from the spiked value, respectively. The LOD was estimated to be 0.44ngmL^–1 (determined as two times the standard deviation of the blank, n=6). The on-line method has the advantages of being relatively easy to automate in the continuous flow mode and is adaptable for use in conjunction with HPLC separations.     

On the Applicability of Duolite GT-73 to Column Preconcentration of Gold and Palladium Prior to Determination by Inductively Coupled Plasma Atomic Emission Spectrometry

The preconcentration of Au and Pd on Duolite GT-73 chelating resin with the thiol functional group was investigated prior to determination of these noble metals by means of inductively coupled plasma atomic emission spectrometry. It was found that Au^III and Pd^II were retained on the resin along with other concomitant metals (Al, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb and Zn) from different HCl-containing media. A two-step elution procedure was developed for the release of the noble metals. First 4.0molL^–1 HNO₃ solution was used to elute the base metals. The recovery of Au and Pd was performed afterwards using 0.50molL^–1 solution of (NH₂)₂CS. Retrieval of Au and Pd retained on Duolite GT-73 was also carried out by decomposition of the resin in the open vessel system using H₂SO₄ with H₂O₂. The detection limits of Au and Pd evaluated for the devised protocol, with a preconcentration factor of 50, were 0.085µgL^–1 and 0.28µgL^–1, respectively. The proposed method was applied to the determination of Au and Pd in spiked electrolytic bath samples.     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

A Simple Sensitive Spectrophotometric Method for the Determination of Ce4+ Using Variamine Blue as a Chromogenic Reagent

A rapid and sensitive spectrophotometric method is described for the determination of trace amounts of cerium using Variamine Blue (VB) as a chromogenic reagent. The proposed method is based on the reaction of cerium with potassium iodide in acidic medium to liberate iodine, which oxidizes Variamine Blue to give a violet colored species with an absorption maximum at 560nm. Beers law was obeyed in the range 2–10µg mL^–1 of cerium. The molar absorptivity and Sandells sensitivity are found to be 1.65×10⁴L mol^–1cm^–1 and 8.48×10^–3µgcm^–2, respectively. The proposed method has been successfully applied to the determination of cerium in alloy and synthetic mixtures.     

Solid-Phase Extraction with Slurry Injection of the Resin Into ETAAS for Trace Determination of Thallium in Natural Water

Thallium in natural water samples was determined by electrothermal atomic absorption spectrometry after 1000-fold enrichment by mini solid-phase extraction from a 100-mL sample solution. A Tl-pyrrolidine-1-carbodithioate complex formed in a sample solution of pH 1.6 was extracted on fine particles of a cellulose nitrate resin dispersed in the sample solution. The cellulose nitrate resin was then collected on a membrane filter (25mm^ø) by filtration under suction using a glass funnel with an effective filtration area of 0.64cm². As a result, a circular thin layer of the resin phase with a diameter of 9mm was obtained. Then the resin phase was carved out by an acrylate resin puncher with a 10-mm^ø hole to put it into a sample cup containing 100µL of 10mM HNO₃ containing 0.5mM NaCl. The resin phase was suspended in the solution by ultrasonication. 1000-fold enrichment was thus attained within 15min, and the suspension was delivered to electrothermal atomic absorption spectrometry. The linear calibration graph was obtained in the range of 0–4ng of Tl in 100mL of a sample solution. The detection limit obtained by 3 method was 0.19ng. The proposed method was applied to the determination of Tl in natural water samples. The results showed the concentration of Tl in seawater was 12.1±1.8pgmL^–1 for the calibration graph method and 12.6±1.4pgmL^–1 for the standard addition method. A snowmelt sample contained 20.7±1.0pgmL^–1 of Tl.     

Simultaneous determination of aluminium and iron in glasses,phosphate rocks and cement using first- and second-derivative spectrophotometry

First- and second-derivative spectrophoto-metric methods for the simultaneous determination of aluminium and iron in their mixtures are described. The methods are based on the colored complexes formed by aluminium and iron with hematoxylin in the presence of cetyltrimethylammonium bromide as a surfactant. The zero-crossing method has been utilized to measure the first- and second-derivative value of the derivative spectrum. Aluminium (0.05–1 gml^-1) could be determined in the presence of iron (0.09–1.6 gml^-1) and vice versa. The detection limits of aluminium and iron are 0.01 and 0.09 gml^-1, respectively in the first-derivative mode and 0.014 and 0.1 gml^-1 in the second-derivative mode. The proposed method has been applied to the simultaneous determination of aluminium and iron in glasses, phosphate rocks, cement and magnesite alloy.     

Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Fluorimetric Flow-Through Sensing of Quinine and Quinidine

We describe a single continuous-flow method for the determination of Quinine (QN) and Quinidine (QD) based on the enhancement of their native fluorescence by on-line transitory retention on a solid support placed in a flow cell. KCl solution was used as carrier/self-eluting solution. The active solid surface is regenerated by the carrier itself which also acts as eluting solution, thus making the microsensing zone reusable for subsequent measurements.In the range of 40 to 1260µL, the response of the sensor (_exc/_em=250/450nm) was directly proportional to the sample volume injected. The sensor was calibrated for three injection volumes: 40, 600 and 1000µL, responding linearly in the range of 40–800, 2–40 and 0.4–20µgL^–1 of QN and 20–600, 5–40 and 0.9–20µgL^–1 of QD with detection limits of 2.2, 0.2 and 0.1µgL^–1 (QN) and 3.9, 0.4 and 0.2µgL^–1 (QD), respectively. The relative standard deviation for ten independent determinations is 1.0% (QN) and 3.9% (QD). The sampling frequency ranges between 40 and 22h^–1 depending on the sample volume injected. This sensor was satisfactorily applied to the determination of QN in soft drink samples and a shampoo, and to the determination of QD in pharmaceutical preparations with equally satisfactory results.     

Application of Lanthanide-Sensitised Chemiluminescence to the Determination of Levofloxacin, Moxifloxacin and Trovafloxacin in Tablets

A flow injection method including chemiluminescence detection has been developed and applied to the determination of fluoroquinolones levofloxacin, moxifloxacin and trovafloxacin in tablets. The proposed method is based on the luminescent properties of the system Ce(IV)–sulphite–fluoroquinolone and the addition of a trivalent lanthanide ion as emission-sensitizer. The optimum conditions for chemiluminescence emission were investigated for each fluoroquinolone. The best results were achieved when employing Eu(III) as lanthanide cation for levofloxacin and moxifloxacin, and Tb(III) for trovafloxacin. These fluoroquinolones were determined over the concentration range of 0.5–3.5µgmL^–1, 0.2–3.0µgmL^–1 and 0.008–0.400µgmL^–1, with detection limits of 0.100, 0.035 and 0.008µgmL^–1, respectively. The relative standard deviations were in the range of 1.0–2.5% for all three cases. The method was applied to the determination of three fluoroquinolones in their respective pharmaceutical preparations and compared with an independent UV-spectrophotometric method. The results were satisfactory.     

Antioxidative and antitumour properties of metal(II) solid complexes with 8-acetyl-4-methyl umbelliferone

Six transition metal(II) complexes with 8-acetyl-4-methyl umbelliferone (AMUH), ML2 (L=AMU^–; M=Mn, Co, Ni, Cu, Zn and Cd), have been synthesized and characterized by elemental analysis, electrical conductance, i.r., 1H-n.m.r. and u.v. spectroscopic techniques. The e.s.r. spectra show that CuL2 is anisotropic, with g2.05 and g2.26. The MnL2 species is characterized by a very broad g2 centered resonance without manganese hyperfine structure. The antioxidative and other biological activities of selected complexes were also investigated, indicating that both the ligand and complexes exhibit a scavenging effect on the superoxide radical (O₂ ^–·) and a suppressing effect on the hydroxyl radical (·OH). The suppressing effect on ·OH is greater than the scavenging effect on O₂ ^–·. The Cu and Mn complexes exhibit very significant suppression ratios for both radicals. However, the inhibitory effect on lipid peroxides results show that, in the initial stage, the Cu and Mn complexes exhibit obvious inhibitory effects on lipid peroxides, but after one hour, they begin to accelerate the lipid peroxides. Lower catalytic activity and instability when the complexes react with active oxygen may be responsible for this dual nature. The ligand and four transition metal(II) complexes selectively, obviously, inhibit the growth of HCT-8 and HL-60 tumour cell lines. They also exhibit a minor influence on the proliferation of B cells in higher concentration (10^–5m), but only a weak effect on the proliferation of T cells of the BALB/C (nude rate) spleen cells.