石墨烯/十二烷基硫酸钠复合物修饰碳糊电极测定氯霉素

以液体石蜡和硅油为混合粘合剂,与石墨粉混合制备了碳糊电极基底电极,将石墨烯/十二烷基硫酸钠复合物修饰在基底碳糊电极上,得到了基于石墨烯复合物的新型修饰碳糊电极。应用扫描电镜和循环伏安法分别研究了该电极的表面特性和电化学性质,结果表明,石墨烯和十二烷基硫酸钠修饰的碳糊电极增大了比表面积,有利于电子传递。在pH 3.0的HAc-NaAc缓冲溶液中,该修饰碳糊电极对氯霉素具有良好的电化学响应,氧化峰电位为0.194 V,氧化峰电流是基底碳糊电极的10倍。在最优实验条件下,该氧化峰电流与氯霉素的浓度在1.0×10~(-8)~5.0×10~(-4)mol/L范围内呈良好的线性关系,检出限为5.0×10~(-9)mol/L。该方法简便,重现性及选择性好,用于测定氯霉素滴眼液和虾中氯霉素残留,结果满意。     

Voltammetric determination of sinomenine in biological fluid using a glassy carbon electrode modified by a composite film of polycysteic acid and carbon nanotubes

Polycysteic acid based electrochemical oxidation of L-cysteine (CySH) and carbon nanotubes (CNTs) formed a composite thin film material at a glassy carbon electrode (GCE) that was used a novel modifier for electroanalytical determination of sinomenine which is used for rheumatoid arthritis treatment. The determination of sinomenine at the composite modified electrode was studied by differential pulse voltammetry (DPV). The peak current obtained at + 0.632 V (vs SCE) from DPV was linearly dependent on the sinomenine concentration in the range of 1.0 x 10(-7) to 6.0 x 10(-5) M in a B-R buffer solution (0.04 M, pH 1.81) with a correlation coefficient of 0.998. The detection limit (S/N = 3) was 5.0 x 10(-8) M. The electrochemical reaction mechanism of sinomenine was also discussed. This new method was then applied to the high-throughput determination of sinomenine in human serum samples with satisfactory results. This polycysteic acid/CNTs composite film may be considered to be a promising, low-cost, durable, and biocompatible material for the modification of sensors in applications to pharmaceutical and biomedical analysis.     

离子液体BMIMPF6修饰碳糊电极电化学测定维生素E

用疏水性离子液体1-丁基-3-甲基咪唑六氟磷酸([BMIM]PF6)作粘合剂制备了离子液体修饰碳糊电极(IL/CPE)。采用循环伏安法(CV)研究了维生素E(vitamin E,VE)的氧化产物生育酚红在IL/CPE和未修饰碳糊电极(CPE)上的电化学行为,结果表明生育酚红在IL/CPE上氧化过程更易于进行,峰电流响应ip也明显增加,表明IL/CPE对生育酚红的氧化还原反应具有良好的电催化作用。同时测定了电极过程的动力学参数:电荷转移系数α=0.8746,扩散系数D=1.65×10-3cm2/s,电极反应速率常数kf=6.64×10-2cm/s。采用方波伏安法(SWV)发现生育酚红氧化峰电流与其浓度在1.53×10-4mol/L～8.39×10-7mol/L范围内呈线性关系,检出限为1.58×10-8mol/L。该法可用于VE实际样品的分析测定。     

尿酸和叶酸存在下改性碳纳米管糊电极上多巴胺电催化氧化MohammadMazloum-Ardakani,MahboobeAbolhasani,Bibi-FatemehMirjalili,MohammadAliSheikh-Mohseni,AfsanehDehghani-Firouzabadi,AlirezaKhoshroo简

A chemically modified carbon paste electrode (CPE), consisting of 2,2''-[(1E)-(1,2-phenylenebis(azanylylidene)] bis(methanylylidene)]bis(benzene-1,4-diol) (PBD) and multiwalled carbon nanotubes (CNTs), was used to study the electrocatalytic oxidation of dopamine using cyclic voltammetry, chronoamperometry, and differential pulse voltammetry (DPV). First, the electrochemical behavior of the modified electrode was investigated in buffer solution. Then the diffusion coefficient, electrocatalytic rate constant, and electron-transfer coefficient for dopamine oxidation at the surface of the PBD-modified CNT paste electrode were determined using electrochemical approaches. It was found that under optimum conditions (pH = 7.0), the oxidation of dopamine at the surface of such an electrode occurred at about 200 mV, lower than that of an unmodified CPE. DPV of dopamine at the modified electrode exhibited two linear dynamic ranges, with a detection limit of 1.0 μmol/L. Finally, DPV was used successfully for the simultaneous determination of dopamine, uric acid, and folic acid at the modified electrode, and detection limits of 1.0, 1.2, and 2.7 μmol/L were obtained for dopamine, uric acid, and folic acid, respectively. This method was also used for the determination of dopamine in a pharmaceutical preparation using the standard addition method.     

Electropolymerisation of L-arginine at carbon paste electrode and its application to the detection of dopamine, ascorbic and uric acid

L-arginine was electropolymerised on a carbon paste electrode (CPE) to form the biopolymer by free radical formation in the electro oxidation process of the amino and carboxylic group containing compound by cyclic voltammetric technique. The modified electrode shows an excellent electrocatalytic activity towards the oxidation of both dopamine (DA) and ascorbic acid (AA). It was demonstrated that the deposited biopolymer has positive charges over the bare carbon electrode surface, which leads to the formation of electrical double layer made the fast electron transfer process could leads to the diffusion of dopamine, ascorbic acid and uric acid on their charge gradient by cyclic voltammetric technique. The response of the sensor was tested towards the different dopamine concentration. The catalytic peak current obtained was linearly related to DA concentrations in the ranges of 5×10(-5) to 1×10(-4)M L(-1) with correlation co-efficient of 0.9924 which reveals the adsorption controlled process. The detection limit for dopamine was 5×10(-7)M L(-1). The interference studies showed that the modified electrode exhibits excellent selectivity in the presence of large excess of ascorbic acid (AA) and response is fast stable, reliable, resistant to biofouling and can be applied for the real sample analysis in medical, pharmaceutical and biotechnological sectors. The adsorption-controlled process and kinetic parameters of the poly(L-arginine) were determined using electrochemical approaches.     

多巴胺在聚钙羧酸膜修饰碳糊电极上的电催化及与尿酸的同时测定

采用循环伏安法(CV)制备了聚钙羧酸(PCCA)膜修饰的碳糊电极(CPE)。考察了电极对多巴胺(DA)、尿酸(UA)的电氧化催化性能。结果显示,聚钙羧酸膜修饰碳糊电极(PCCA/CPE)对DA有良好的电催化效果,DA呈现出一对准可逆的氧化还原峰,氧化峰电流与DA浓度在3.0×10-7～1.0×10-4mol/L范围内呈线性关系,检出限为1×10-7mol/L(S/N=3)。使用微分脉冲伏安法(DPV),DA和UA在PCCA/CPE上的氧化峰能完全分离(ΔEp=192 mV),且峰电流与浓度均呈现良好的线性关系,可实现对DA和UA的同时测定。实验还进行了实际样品测定。     

Preparation of tetraheptylammonium iodide-iodine graphite-multiwall carbon nanotube paste electrode: electrocatalytic determination of ascorbic acid in pharmaceuticals and foods

The present work describes the construction of a new modified graphite-multiwall carbon nanotube paste electrode by casting the appropriate mixture of tetraheptylammonium iodide-iodine as a new modifier. The modified paste electrode was used for the determination of ascorbic acid (AA) in a phosphate buffer solution (pH 2.0). When compared to activated carbon, a graphite and multiwall carbon nanotube paste electrode containing a new modifier, the proposed modified paste electrode not only shifted the oxidation potential of AA towards a less-positive potential but also enhanced its oxidation peak current. Further, the oxidation of AA was highly stable at the modified paste electrode. The optimum analytical conditions were sought. The current response of AA increases linearly while increasing its concentration from 5.6 × 10(-5) to 1.2 × 10(-2) M with a correlation coefficient of 0.9991; the detection limit (3σ) was found to be of 3.6 × 10(-5) M. The present modified paste electrode was also successfully used for the determination of AA in the presence of common interference compounds. The present modified electrode was successfully demonstrated towards the determination of AA in pharmaceutical and food samples.     

双酚A在SDS现场自组装膜与[bupy]PF6复合修饰碳糊电极上的电催化氧化及电分析方法

研究了双酚A(BPA)在十二烷基硫酸钠(SDS)现场自组装膜与离子液体N-丁基吡啶夫氟磷酸盐([ bupy]PF6)复合修饰碳糊电极(SDS-[ bupy]PF6/CPE)上的电催化氧化行为和电化学动力学性质.实验结果表明,在SDS-[ bupy]PF6/CPE上BPA发生了一受扩散控制的不可逆电化学氧化过程,用循环伏安(CV)法和计时电流(CA)法测得BPA在SDS-[bupy]PF6/CPE上的电极反应过程动力学参数.用方波伏安(SWV)法测得BPA氧化峰电流(Ipa)与其浓度在1.0×10-5～ 1.0×10-3 mol/L范围内呈良好的线性关系,线性方程为Ipa(μA) =2.635 +51.30c( 10-3 mol/L),r =0.998 1,检测限(S/N=3)为3.01×10-7 mol/L,同时运用SWV法对湖水样品中双酚A的含量进行了电化学定量测定.     

Poly(amidosulfonic acid) modified glassy carbon electrode for determination of isoniazid in pharmaceuticals

Amidosulfonic acid was electropolymerized by cyclic voltammetry onto the surface of glassy carbon electrode (GCE) to fabricate the chemically modified electrode, which showed high stability, good selectivity and reproducibility for determination of isoniazid. The modified electrode showed an excellent electrocatalytical effect on the oxidation of isoniazid. Under the optimum conditions, there was a good linear relationship between anodic peak current and isoniazid concentration in the range of 5.0 x 10(-8)- 1.0 x 10(-5) M, and a detection limit of 1.0 x 10(-8) M (S/N = 3) was obtained after 120 s at the accumulation potential of - 0.2 V (vs. SCE). This developed method had been applied to the direct determination of isoniazid in injection and tablet samples with satisfactory results.     

Electro-oxidation and determination of antihistamine drug, cetirizine dihydrochloride at glassy carbon electrode modified with multi-walled carbon nanotubes

A multi-walled carbon nanotube (MWCNT) film-modified glassy carbon electrode (GCE) was constructed for the determination of an antihistamine drug, cetirizine dihydrochloride (CTZH) using cyclic voltammetry (CV). Owing to the unique structure and extraordinary properties of MWCNT, the MWCNT film has shown an obvious electrocatalytic activity towards oxidation of CTZH, since it facilitates the electron transfer and significantly enhances the oxidation peak current of CTZH. All experimental parameters have been optimized. Under the optimum conditions, the oxidation peak current was linearly proportional to the concentration of CTZH in the range from 5.0×10(-7) to 1.0×10(-5)M. The detection limit was 7.07×10(-8)M with 180s accumulation. Finally, the proposed sensitive and simple electrochemical method was successfully applied to CTZH determination in pharmaceutical and urine samples.     

硫化物在乙酰二茂铁修饰碳糊电极上的电化学行为及电分析

研究了S2-在乙酰二茂铁(AFc)修饰碳糊电极(AFc/CPE)上的电催化氧化行为及其电化学分析方法。实验结果表明,AFc/CPE对S2-的电化学氧化具有良好的催化作用。用计时电流法(CA)测定了S2-在AFc/CPE上的电催化氧化反应速率常数k为(2.60±0.05)×105 L.mol-1.s-1。用方波伏安法(SWV)测得催化氧化峰电流与S2-的浓度在5.0×10-5～1.0×10-3 mol.L-1范围内呈良好线性关系,检出限(S/N=3)为1.3×10-7 mol.L-1,同时运用SWV法对造纸废水水样中S2-的含量进行了电化学定量测定。     

美索巴莫在［BnMIM］PF6修饰碳糊电极上的电催化氧化及电分析方法

研究了美索巴莫（MET）在离子液体1-苄基-3-甲基咪唑六氟磷酸盐［BnMIM］PF6修饰碳糊电极（［BnMIM］PF6/CPE）上的电催化氧化行为和电化学动力学性质,并用循环伏安法（CV）、计时电流法（CA）测得MET在［BnMIM］PF6/CPE上的电极反应过程动力学参数。实验结果表明,MET在［BnMIM］PF6/CPE上发生了受扩散控制的不可逆电化学氧化过程。用方波伏安法（SWV）测得MET氧化峰电流（Ipa）与其浓度在3.0×10-5~1.0×10-2 mol?L-1范围内呈良好线性关系,检出限（S/N=3）为3.3×10-6 mol?L-1。同时运用SWV法对市售美索巴莫片进行电化学定量测定,RSD为1.5%~2.5%,加标回收率为98%~99%。     

Sodium dodecyl sulfate-modified carbon paste electrodes for selective determination of dopamine in the presence of ascorbic acid

A carbon paste electrode (CPE) modified by a monolayer film of sodium dodecyl sulfate (SDS) was used for detection of dopamine (DA). Cyclic voltammetry demonstrated improved response of the DA sensor. This suggests the effectivity of surface modification of CPE by SDS. Impedance spectroscopy was used for the characterization of CPE surface properties. The effect of SDS concentration on the electrode quality also reveals that SDS formed a monolayer on CPE surface with a high density of negative-charged end directed outside the electrode. As a result, the carbon paste electrode modified with SDS (SDS/CPE) exerted discrimination against ascorbic acid in physiological circumstance. Thus, it can selectively determine dopamine even in the presence of 220-fold AA combined with differential pulse stripping voltammetry. In pH 7.40 phosphate buffer solution, the oxidation peak current on differential pulse voltammograms increases linearly with the concentration of DA in the range of 5.0 x 10(-7) to 8.0 x 10(-4) mol . L(-1) with a detection limit of 5.0 x 10(-8) mol . L(-1). Satisfying results are achieved when detecting the DA in injection and simulated biology sample.     

沙丁胺醇在SDBS现场自组装膜与［BnMIM］PF6复合修饰碳糊电极上的电催化氧化及电分析方法

研究了沙丁胺醇(SAL)在表面活性剂十二烷基苯磺酸钠(SDBS)现场自组装膜与离子液体1-苄基-3-甲基咪唑六氟磷酸盐([BnMIM]PF6)复合修饰碳糊电极(SDBS-[BnMIM]PF6/CPE)上的电催化氧化行为和电化学动力学性质。实验结果表明,SDBS-[BnMIM]PF6/CPE对SAL的电化学氧化具有良好的催化作用。用循环伏安法(CV)和计时电流法(CA)测得SAL在SDBS-[BnMIM]PF6/CPE上的电极反应过程动力学参数。用方波伏安法(SWV)测得SAL氧化峰电流(Ipa)与其浓度在9.0×10-5～1.0×10-3mol.L-1范围内呈良好的线性关系,检出限(S/N=3)为1.08×10-6mol.L-1。运用该方法对市售吸入用沙丁胺醇溶液中SAL的含量进行了测定,结果满意。     

Voltammetric determination of terbinafine in biological fluid at glassy carbon electrode modified by cysteic acid/carbon nanotubes composite film

The electrochemical oxidation of L-cysteine (CySH) in presence of carbon nanotubes (CNTs) formed a composite film at a glassy carbon electrode (GCE) as a novel modifier for directly electroanalytical determination of terbinafine without sample pretreatment in biological fluid. The determination of terbinafine at the modified electrode with strongly accumulation was studied by differential pulse voltammetry (DPV). The peak current obtained at +1.156 V (vs. SCE) from DPV was linearly dependent on the terbinafine concentration in the range of 8.0 x 10(-8)-5.0 x 10(-5 )M in a B-R buffer solution (0.04 M, pH 1.81) with a correlation coefficient of 0.998. The detection limit (S/N=3) was 2.5 x 10(-8 )M. The low-cost modified electrode showed good sensitivity, selectivity, and stability. This developed method had been applied to the direct determination of terbinafine in human serum samples with satisfactory results. It is hopeful that the modified electrode will be applied for the medically clinical test and the pharmacokinetics in future.     

Electrochemical sensor for neurotransmitters at physiological pH using a heterocyclic conducting polymer modified electrode

We report the simultaneous determination of two neurotransmitters, norepinephrine (NEP) and serotonin (5-HT), at physiological pH using the electropolymerized film of 3-amino-5-mercapto-1,2,4-triazole modified glassy carbon (p-AMTa) electrode. A bare glassy carbon (GC) electrode fails to resolve the voltammetric signals of NEP and 5-HT due to the surface fouling caused by the oxidized products of them. However, the p-AMTa electrode not only separates the voltammetric signals of NEP and 5-HT with a potential difference of 150 mV between NEP and 5-HT but also shows higher oxidation currents for them. The simultaneous determination of NEP and 5-HT was successfully achieved at p-AMTa electrode using differential pulse voltammetry method. The amperometric current response increased linearly with increasing NEP and 5-HT concentration in the range of 1.0 × 10(-8) to 1.0 × 10(-4) M and 1.0 × 10(-8) to 5.0 × 10(-5) M, respectively, and the detection limit was found to be 1.65 × 10(-11) for NEP and 1.32 × 10(-11) M for 5-HT (S/N = 3). The p-AMTa electrode shows better recovery results for spiked NEP and 5-HT in human blood plasma samples.     

The electrochemical oxidation of pentachlorophenol and its sensitive determination at chitosan modified carbon paste electrode

We report on a novel electrochemical method to detect trace pentachlorophenol (PCP) by using a chitosan (CS) modified carbon paste electrode (CS/CPE). Compared with that at a bare carbon paste electrode (CPE), the current response was greatly improved at the CS/CPE due to the enhancement effect of CS. Under optimal working conditions, the oxidation peak current of PCP was proportional to its concentration in the range of 1.0 × 10^?7 to 5.0 × 10^?6 and 5.0 × 10^?6 to 1.0 × 10^?4 mol/L, with an extremely low detection limit of 4.0 × 10^?8 mol/L. Our method was successfully used to detect the PCP concentration in vegetable samples.     

基于表面活性剂增敏有序介孔SiO2修饰碳糊电极测定L-色氨酸

利用水热法合成得到有序介孔二氧化硅( OMS),采用X射线衍射、N2吸附-脱附、透射电镜等技术对其进行了表征。制备OMS修饰碳糊电极( OMS/CPE),采用循环伏安和交流阻抗技术考察了修饰电极的电化学性能,发现与裸碳糊电极(CPE)相比,OMS/CPE具有更大的电活性面积和更快的电子传导速率。研究了L-色氨酸(L-Trp)在表面活性剂十二烷基磺酸钠(SDS)存在下,在OMS/CPE上的电化学行为和动力学性质,结果表明,OMS和SDS具有良好的协同作用,能明显增加L-Trp的响应信号; SDS存在下,L-Trp在修饰电极上的电化学氧化是2电子和2质子参加的不可逆过程,电极过程受吸附控制。优化了表面活性剂浓度、富集时间、富集电位、介质 pH 值等测定参数,在最优条件下, L-Trp 氧化峰电流与其浓度在8.0×10-8~4.0×10-6 mol/L范围内呈良好线性关系,检出限为7.0×10-8 mol/L(S/N=3)。本方法用于氨基酸口服液样品的加标回收检测,回收率为99.6％~102.6％。     

多壁纳米管修饰电极电催化3,4-二羟基苯甲酸研究

应用循环伏安(CV)和方波伏安(SWV)法研究3,4-二羟基苯甲酸(DHBA)在多壁碳纳米管修饰的玻碳电极上的电化学行为.实验表明:该修饰电极对DHBA有较强的电催化作用.由方波伏安法测定的氧化峰电流在DHBA浓度为4.0×10-6~1.0×10-4mol/L和2.0×10-4~8.0×10-4mol/L范围内分段呈线性变化关系;相关系数各为0.9995和0.9992,检测限1.0×10-6mol/L.     

基于表面活性剂单分子层修饰碳糊电极的一氧化氮电化学传感器及其应用

报道了一种表面活性剂单分子层修饰碳糊电极,并用于NO的高灵敏电化学检测。研究表明,表面活性剂通过烷基链在电极表面形成的疏水性单分子层微环境对NO的电化学响应具有较好的促进作用。其中,阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)对NO的电化学氧化表现出最强的催化活性和增敏作用。在Nafion膜覆盖的CTAB修饰碳糊电极上,NO的安培响应与其浓度在3.6×10-8～1.8×10-5mol/L范围内呈良好的线性关系,检出限为1.8×10-8mol/L。该电极作为低成本、高灵敏的NO电化学传感器,被成功应用于大鼠肺组织细胞中NO释放的实时监测。