混合基质水处理膜:材料、制备与性能

以反渗透、纳滤为代表的膜技术已广泛应用于海水和苦咸水脱盐等水处理过程。通过将纳米颗粒添加到传统复合膜基质中,可以制备具有高分离性能和耐污染性的新型膜材料。混合基质膜结合了无机材料及有机聚合物各自的优点,是新型水处理膜材料的发展方向。本文综述了添加无机纳米颗粒的混合基质反渗透、纳滤及正渗透膜的研究进展,详细讨论了不同类型纳米材料的性质和功能,分析了表面有机改性对改善纳米材料分散性以及与聚合物基质相容性的作用,探讨了纳米材料添加方式和膜制备方法对膜结构和性能的影响。在此基础上,进一步探究了混合基质膜的成膜及分离机理,归纳了目前研究中存在的主要问题,并对未来水处理膜材料的研发方向提出了建议。     

ZnO、CuO和NiO纳米颗粒在基质辅助激光解吸电离-飞行时间质谱分析小分子化合物中的应用

考察了过渡金属氧化物ZnO纳米颗粒直接作为无机基质,应用于基质辅助激光解吸电离飞行时间质谱( MALDI-TOF-MS)法分析糖类、硬脂酸小分子物质的效果;同时以L-精氨酸为目标分析物,初步探讨了CuO和NiO两种纳米颗粒直接作为无机基质,对L-精氨酸选择性离子化的可行性。实验中,将待分析物与纳米颗粒悬浮液直接混合于样品板上,自然蒸干溶剂形成结晶状,采用337 nm波长的紫外激光辐照激发,在反射模式的TOF-MS条件下检测分析。结果表明, ZnO纳米颗粒作为一种半导体材料,具有较强的紫外吸收,可直接作为无机基质,能够避免使用传统基质带来的干扰,简化质谱图,尤其在负离子模式下能够提高硬脂酸离子化的峰强度。此外,通过比较CuO和NiO纳米颗粒对于L-精氨酸分析检测结果的差异性,初步实现了Cu+对L-精氨酸的选择性检出。     

四种无机纳米颗粒对塑料抗紫外性能的研究进展

无机纳米颗粒在塑料抗紫外的研究中一直备受关注,主要介绍了四种(TiO₂、ZnO、SiO₂、CeO₂)典型的无机纳米颗粒在该领域的应用。首先归纳了其既能吸收又能反射或散射紫外线的抗紫外机理;其次,分别论述了不同无机纳米颗粒适用的紫外光波长范围,以在塑料中的添加方法和应用特点为主线,重点介绍了国内外四种无机纳米颗粒在塑料抗紫外性能中的研究现状和进展;最后,将四种无机纳米颗粒在塑料抗紫外性能中的应用特点进行了对比,提出了应用过程中存在的分散和相容性差等问题,以期为无机纳米颗粒的深入应用和发展提供一定的参考。     

液态有机-无机纳米颗粒离子化材料合成及结构研究进展

有机-无机纳米颗粒离子化材料（NIMs）是由无机纳米颗粒核和与其以共价键相连的离子化有机齐聚物或低聚物的冠状层组成的有机-无机杂化材料。根据核和冠状层的几何和化学性质，如纳米核的尺寸、形状及含量，有机层的分子量及接枝度的不同，NIMs可以是从玻璃态固体到自由流动的流体，即纳米颗粒离子化流体（Nms）。液态有机-无机纳米...     

原位沉析法制备有序排列四氧化三铁/壳聚糖纳米复合材料的研究

生物矿物由于具有完美结构及独特的生物活性,使其成为制备新型有彬无机杂化纳米复合材料的思想来源,在目前制备的有机／无机纳米复合材料中,纳米粒子在聚合物基质中大部分是无规分散的,但无机纳米颗粒在有机物中的有序排列是生命体中的一种根本体现,有序排列会使材料的性能更加优异。人骨的主要成分是纳米羟基磷灰石晶体和胶原,羟基磷灰石晶体是沿着胶原纤维的长轴方向有序排列的,这使得人骨不仅具有生物活性,而且具有非常好的力学性能。     

Fe-Ni/C复合纳米纤维的原位制备与微波吸收性能

采用静电纺丝技术结合稳定化和碳化处理原位制备了Fe-Ni/C复合纳米纤维, 其平均直径约为215 nm, 所生成的Fe-Ni合金纳米颗粒较均匀地分布在碳基纳米纤维的内部和表面, 且被石墨化碳层所包覆. 以Fe-Ni/C复合纳米纤维为吸收剂、 硅橡胶为基质制备成吸波涂层, 研究了碳化温度对电磁特性和微波吸收性能的影响. 结果表明, 涂层厚度为1.2~2.0 mm、 Fe-Ni/C复合纳米纤维质量分数为5%的吸波涂层表现出优良的微波吸收性能, 在7.4~18 GHz频率范围内的反射损耗均低于-20 dB; 随着复合纳米纤维的碳化温度由800 ℃升高到1200 ℃, 由于阻抗匹配特性的改善, 吸波涂层的微波吸收能力逐步加强, 其最小反射损耗由-22.6 dB降低到-63.0 dB.     

基于树枝状聚合物的无机纳米颗粒的制备及应用

树枝状聚合物具有一些独特性质,包括规整且高度支化的三维结构、完美单分散尺寸、内部空腔以及表面大量的官能团等,因而其在催化、检测、生物医用领域具有潜在应用。这些应用的改进或者实现,往往需要在树枝状聚合物中引入无机纳米颗粒,从而制备得到基于树枝状聚合物的无机纳米颗粒。另一方面,树枝状聚合物的存在能够提升无机纳米颗粒在溶液中的稳定性、抑制团聚,从而长时间保留纳米颗粒的优异性能。在过去几十年,因为其优异的性质和潜在的应用,基于树枝状聚合物的无机纳米颗粒吸引了众多科研人员的关注。依据其结构特点,可以将基于树枝状聚合物的无机纳米颗粒大致分为以下三类:(1)树枝状聚合物包裹的无机纳米颗粒;(2)树枝状聚合物稳定的无机纳米颗粒;(3)树枝化基元稳定的无机纳米颗粒。本文侧重归纳并总结近五年基于树枝状聚合物的无机纳米颗粒的制备方法,以及其在催化、生物医用、检测领域的研究进展,并对其制备方法和应用发展进行了展望。     

壳聚糖静电纺纳米纤维的制备和特点

对纯壳聚糖、壳聚糖和聚合物的混合物、壳聚糖和蛋白质的混合物、壳聚糖衍生物、壳聚糖和无机纳米颗粒的混合物等静电纺纳米纤维的制备和特点进行了综述,对部分壳聚糖纳米纤维的应用进行了简述。     

电纺含银纳米粒子复合纤维的制备及应用

银纳米粒子由于其特殊的物理化学性质而被广泛应用,但其易团聚,影响实际使用效果。银纳米粒子可被负载到稳定载体上,获得具有优异性能的纳米复合材料,克服了团聚等缺限,大大改善应用效果和效率。采用静电纺丝技术制备银修饰纳米复合纤维材料是其中一种有效的方法,近年来在复合材料制备领域受到了广泛关注。本文综述了最近几年关于静电纺丝制备负载银纳米颗粒纤维复合材料及其应用的研究进展,重点介绍了静电纺丝制备负载银纳米纤维过程中纳米银的生成和负载方法,总结了有机主体和无机主体两种纺丝纤维的制备研究进展,详细介绍了负载银纺丝纤维在几个重要领域的应用及研究方向。     

Ag/ZnO纳米纤维的制备及光催化性能

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维, 然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面. 利用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 能量色散X射线光谱(EDX)、 扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征. SEM结果表明, 直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构. 以常见的有机污染物甲基橙、 亚甲基蓝和罗丹明B等为降解底物, 对Ag/ZnO纳米纤维的光催化性能进行了表征. 结果表明, 负载银纳米颗粒后, 复合催化剂的光催化性能明显提高.     

Cellulose-based fibers from liquid–crystalline solutions. II. Processing and morphology of acetate/butyrate esters

Fibers were spun from isotropic and anisotropic dimethylacetamide solutions of cellulose esters. Take-up speeds of the dry jet/wet spinning process varied. Water served as the coagulant. The mechanical properties of the fibers increased as spinning progressed from the isotropic to the anisotropic state of the solution. A trade-off in solubility and fiber properties was noted as the butyryl acetyl ratio decreased. Whereas high butyryl content enhances both overall solubility and the formation of liquid–crystalline solutions at lower concentration, it results in lower fiber modulus and strength. Morphology of the fibers depended on the coagulation rate which was influenced by the concentration of the sppinning solution. The level of orientation and crystallinity of the fibers increased somewhat when they were spun from liquid-crystalline solutions. © 1993 John Wiley & Sons, Inc.     

Centrifugally spun poly(ethylene oxide) fibers rival the properties of electrospun fibers

Centrifugal force spinning (CFS), also known as centrifugal spinning, forcespinning, or rotary jet spinning, provides considerably higher production rates than electrospinning (ES), but the more widespread use of CFS as an alternative depends on the ability to produce fibers with robust thermal and mechanical properties. Here, we report the CFS of poly(ethylene oxide) (PEO) fibers made using a spinning dope formulated with acetonitrile (AcN) as the volatile solvent, and we describe the thermal and mechanical properties of the centrifugally-spun fibers. Even though the formation, diameter, and morphology of electrospun and centrifugally-spun PEO fibers are relatively well-studied, the article presents three crucial contributions: the pioneering use of PEO solutions in AcN as spinning dope, characterization of crystallinity and mechanical properties of the centrifugally-spun PEO fibers, and a comparison with the corresponding properties of electrospun fibers. We find that fiber formation occurrs for the chosen CFS conditions if polymer concentration exceeds the entanglement concentration, determined from the measured specific viscosity. Most significantly, the centrifugally spun PEO fibers display crystallinity, modulus, elongation-at-break, and fiber diameter that rival the properties of electrospun PEO fibers reported in the literature.     

分子量分布对等规聚丙烯卷绕丝织构形成的影响

本文研究了分子量分布对聚丙烯卷绕丝结构和性能的影响。结果表明,聚丙烯树脂中的高分子量尾端对卷绕丝的结构有明显影响。在通常的纺丝条件下,用控制降解的聚丙烯树脂纺得的卷绕丝具有低取向的次晶结构;而在相同的粘均分子量和纺丝条件下,高分子量尾端的存在使聚丙烯易于在纺丝线上生成结晶性较高的α-晶型,卷绕丝的取向也随高分子量尾端而显著增大。高分子量尾端对卷绕丝结构的影响,导致卷绕丝牵伸性能和成品纤维力学性能变差。     

Analysis of regenerated cellulose fibers with ionic liquids as a solvent as spinning speed is increased

In order to improve the spinning efficiency, the spinning experiments with cellulose/1-butyl-3-methylimidazolium chloride solution were done whilst increasing spinning speed. It was found that the tenacity and initial modulus of regenerated cellulose fibers increased but the elongation at break decreased slightly with increasing spinning speed at constant draw ratio. Further, the synchrotron wide-angle X-ray diffraction and small-angle X-ray scattering were carried out to illustrate the relationship between the structure and the mechanical properties. It was shown that the crystal orientation, crystallinity, amorphous orientation factor as well as orientation of the microvoids along the fiber increased with the spinning speed as the diameter of the microvoids in the fiber decreased. From the analysis of the spinline stress, it is clear that the spinline stress increased when both extruding and draw speed increased at constant draw ratio. This resulted in the improvement of supramolecular structure and mechanical properties of the regenerated cellulose fibers.     

碳纳米管改性聚苯硫醚熔纺纤维的结构与性能研究

将多壁碳纳米管(MWCNTs)和聚苯硫醚(PPS)经过熔融挤出后制备成复合材料切片,并采用熔融纺丝法制得碳纳米管改性聚苯硫醚复合纤维.采用扫描电镜(SEM)、拉曼光谱、示差扫描量热分析(DSC)、动态机械分析(DMA)以及力学性能测试等表征手段研究了复合纤维中碳管的分散状态,与基体的界面作用,复合纤维的结晶性能以及力学性能,从而探讨了聚苯硫醚/碳纳米管复合纤维体系的微观结构与宏观性能之间的关系.研究表明,聚苯硫醚分子结构与碳纳米管之间具有的π-π共轭作用使碳管较为均匀的分散在基体中,界面结合较为紧密.同时熔融纺丝过程中的拉伸作用使碳管进一步解缠并使碳管沿纤维拉伸方向取向.另一方面,拉曼光谱显示拉伸作用有效地增强了界面作用,有利于外界应力的传递.碳管的良好分散以及强的界面作用使复合纤维力学性能得到大幅度的提高,当碳管含量达到5 wt%时,复合纤维的模量有了明显的提高,拉伸强度较纯PPS纤维提高了近220%.     

Effect of processing consitions on the development of morphology in clay nanoparticle filled nylon 6 fibers

The effect of melt temperature on the phase behavior and preferential orientation development in Nylon 6/montmorillonite nanocomposites were investigated at melt spinning temperatures ranging from 230° to 250°C. The fibers were found to exhibit mostly γ crystalline form that is typical of Nylon 6 filled with montmorillonite nanoparticles. At higher take-up speeds α-crystals begin to appear in the crystalline phase. The presence of nanoparticles was found to impart substantial chain orientation levels even at low to moderate take up speeds reaching a plateau at moderate take up speeds. This was attributed to the increased spin line stress in the presence of nanoparticles that increase the overall viscosity due to their large contact areas with the polymer chains. This increased spinline tension was found to cause fiber breakup at moderate speeds. Increasing melt temperature from 230° to 250°C alleviated this problem.     

Mechanical properties of rigid polyurethane composites reinforced with surface treated ultrahigh molecular weight polyethylene fibers

The mechanical properties of ultrahigh molecular weight polyethylene (UHMWPE) fibers reinforced rigid polyurethane (PU) composites were studied, and the effects of the fiber surface treatment and the mass fraction were discussed. Chromic acid was used to treat the UHMWPE fibers, and polyurethane composites were prepared with 0.1 to 0.6 wt% as‐received and treated UHMWPE fibers. Attenuated total reflection Fourier transform infrared demonstrated that oxygen‐containing functional groups were efficiently grafted to the fiber surface. The mechanical performance tests of the UHMWPE fibers/PU composites were conducted, and the results revealed that the treated UHMWPE fibers/PU composites had better tensile, compression, and bending properties than as‐received UHMWPE fibers/PU composites. Thermal gravimetric analyzer showed that the thermal stability of the treated fiber composites were improved. The interface bonding of PU composites were investigated by scanning electron microscopy and dynamic mechanical analysis, and the results indicated that the surface modification of UHMWPE fiber could improve the interaction between fiber and PU, which played a positive role in mechanical properties of composites.     

Alignment effect of attapulgite on the mechanical properties of poly(vinyl alcohol)/attapulgite nanocomposite fibers

Poly(vinyl alcohol) (PVA)/attapulgite (AT) nanocomposite fibers have been prepared by wet spinning. The morphology and mechanical properties of the modified PVA fibers have been characterized with transmission electron microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), birefringence measurements, and mechanical testing. The PVA/AT nanocomposite fibers show much higher tensile strength, initial modulus, and work to break than pure PVA fibers with the same draw ratio. SEM observations demonstrate that the AT nanorods can align orderly along the fiber axis by stretching and have good adhesion to the fiber matrix. The results of birefringence measurements prove that the modified fibers have higher orientation than pure PVA fibers after stretching. The results of DSC analysis indicate that the crystallinity of the PVA fibers can be increased by the addition of AT. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1995–2000, 2006     

含磷聚酰亚胺纤维的制备与性能

合成了一种含磷二胺单体, 二(4-胺基苯氧基)苯基膦氧(DAPOPO). 该单体与4,4'-二胺基二苯醚(ODA)、 均苯四酸二酐(PMDA)和3,3',4,4'-联苯四酸二酐(BPDA)共聚得到聚酰胺酸溶液, 通过干喷湿纺法纺丝得到聚酰胺酸纤维, 聚酰胺酸纤维经过热亚胺化和热牵伸得到含磷的聚酰亚胺纤维. 利用纤维强度仪、 扫描电子显微镜、 热失重分析仪和氧指数测定仪等研究了含磷聚酰亚胺纤维的力学性能、 形貌、 热稳定性能和阻燃性能. 结果表明, 随着含磷量的增加, 纤维的热稳定性明显提高, 而极限氧指数从35上升到了45, 说明纤维的阻燃性能得到很大提高.     

A biodegradable material for ACL reconstruction

Biodegradable polyurethane urea fibers for ACL reconstruction have been produced by wet spinning. By using a short-chain polyester diol as the soft segment in the polyurethane urea the elongation-to-break of the fibers have been reduced to be below 100% instead of 400–800% for spandex fibers, the modulus is increased from 5 MPa to 1 GPa and the tensile strength is increased from 0.1 N/tex to 0.4 N/tex. The composition of the polyester determines at which rate the fiber degrade. Different polyesters have been investigated to find the most suitable degradation rate for ACL application.