The effect of surface wettability on induction and growth of neurites from the PC-12 cell on a polymer surface

Surface properties of polymeric devices that are used to regenerate nervous damage are a point to be considered for axon regeneration in nerve system. In our previous studies, we prepared a wettability gradient on polyethylene (PE) surfaces using a corona discharge treatment from a knife-type electrode whose power increases gradually along the sample length. The PE surfaces were oxidized gradually with increasing power. The effect of surface wettability on the different types of cells has an important role for cell adhesion and proliferation. The purpose of this study is to investigate neurite formation on polymer surfaces with different wettability. Induction and growth of neurites from the rat pheochromocytoma (PC-12) cells attached on the polymer surfaces with different hydrophilicity were investigated using the wettability gradient PE surfaces prepared by a corona discharge treatment. Neurites were investigated for number and length of neurites in terms of surface wettability. It was observed that neurite formation of PC-12 cells was increased more onto the positions with moderate hydrophilicity of the wettability gradient surface than onto the more hydrophobic or hydrophilic positions. From those results, it could be assumed that initial adhesion of PC-12 cells was caused by more calf serum (CS) protein than nerve growth factor (NGF), whereas the neurite formation of PC-12 cells was caused by more NGF than CS protein. It follows from what has been said thus far that PC-12 cells are a differentiated neuronal phenotype with a long neurite at around the position 2.5 cm (water contact angle of about 55 deg). In conclusion, surface wettability plays an important role for neurite formation on the polymer surfaces for axon regeneration.     

A facile method for preparing sticky, hydrophobic polymer surfaces

Textured surfaces consisting of nanometer- to micrometer-sized lightly sulfonated polystyrene ionomer (SPS) particles were prepared by rapid evaporation of the solvent from a dilute polymer solution-cast onto silica. The particle textured ionomer surfaces were prepared by either spin-coating or solution-casting ionomer solutions at controlled evaporation rates. The effects of the solvent used to spin-coat the film, the molecular weight of the ionomer, and the rate of solvent evaporation on the surface morphology of cast films were investigated. The surface morphologies were consistent with a spinodal decomposition mechanism, where the surface first existed as a percolated-like structure and then ripened into droplets if molecular mobility was retained for sufficient time. The SPS particles or particle aggregates were robust and resisted separation from the surface even after annealing at 120 °C for 1 week. The water contact angles on as-prepared surfaces were relatively low, ～90°, due to the polar groups in the ionomer, but when the surface was modified by chemical vapor deposition of 1H,1H,2H,2H-perfluorooctyltrichlorosilane, the surface contact angles increased to ～109° on smooth surfaces and up to ～140° on the textured surfaces. Although the surfaces were hydrophobic, the contact angle hysteresis was relatively high and water droplets stuck to these surfaces even when the surface was turned upside down.     

Emulsions stabilised by food colloid particles: role of particle adsorption and wettability at the liquid interface

We study the effect of the particle wettability on the preferred type of emulsion stabilised solely by food colloid particles. We present results obtained with the recently developed gel trapping technique (GTT) for characterisation of wettability and surface structuring of individual food colloid particles adsorbed at air-water and oil-water interfaces. This method allows us to replicate a particle monolayer onto the surface of polydimethylsiloxane (PDMS) without altering the position of the particles. By observing the polymer surface with scanning electron microscopy (SEM), we are able to determine the contact angle of the individual particles at the initial liquid interface. We demonstrate that the GTT can be applied to fat crystal particles, calcium carbonate particles coated with stearic acid and spray-dried soy protein/calcium phosphate particles at air-water and oil-water interfaces. Subsequently, we prepare emulsions of decane and water stabilised by the same food colloid particles and correlate the wettability data obtained for these particles to the preferred type of emulsions they stabilise.     

Self-organization of polymer particles on hydrophobic solid substrates in aqueous media. II. Self-organization of cationic polymer particles on polymer films and wettability control with particle monolayers

Self-organization of cationic polymer particles through hydrophobic interaction on polymer films in aqueous system and characteristic properties of the resulting particle monolayers were investigated. Cationic polymer particles bearing quaternary ammonium groups on their surfaces effectively self-organized on polymer films. With an increase of the particle surface charge density, the surface coverage and average aggregate size (N _a) decreased. The surface coverage control was accomplished by tuning the ionic strength of the media. The wettability of polymer films for water was imparted by the formation of particle monolayers on them. Annealing of the particle monolayers resulted in the increase of the adhesive strength, while the wettability for water was lost. Further improvements of both wettability and adhesive strength of particle monolayers were achieved by the immobilization of silica colloids on the particle monolayers. This method would be effective for the hydrophilization of polymer films.     

Sliding droplets on superomniphobic zinc oxide nanostructures

This study reports on liquid-repellency of zinc oxide nanostructures (ZnO NS). The ZnO NS are synthesized by an easy and fast chemical bath deposition technique. Three different nanostructured surfaces consisting of nanorods, flowers, and particles are prepared, depending on the deposition time and the presence of ethanolamine in the reaction mixture. Chemical functionalization of the ZnO NS with 1H,1H,2H,2H-perfluorodecyltrichlorosilane (PFTS) in liquid (PFTS L) and vapor phase (PFTS V) or through octafluorobutane (C(4)F(8)) plasma deposition led to the formation of superomniphobic surfaces. A comprehensive characterization of the wetting properties (static contact angle and contact angle hysteresis) has been performed using liquids composed of deionized water and various concentrations of ethanol (surface tension between 35 and 72.6 mN/m). Depending on the nanostructures morphology, coating nature and liquid employed, high static apparent contact angles θ ≈ 150-160°, and low contact angle hysteresis Δθ ≈ 0° are obtained. The different ZnO NS are characterized using scanning electron microscopy (SEM) and contact angle measurements. The results reported in this work permit preparation of sliding omniphobic surfaces using a simple and low cost technique.     

Impact of lipopolysaccharide coating on clay particle wettability

Impact of lipopolysaccharide coating on kaolinite and Na-montmorillonite wettability was investigated. Kaolinite had greater diiodomethane contact angles, smaller water and formamide contact angles than Na-montmorillonite. After lipopolysaccharide coating, diiodomethane and formamide contact angles decreased, while water contact angles increased for both kaolinite and Na-montmorillonite. The decrease and increase in liquid contact angles after lipopolysaccharide coating were most pronounced for lipopolysaccharide extracted from Pseudomonas aeruginosa, followed by Pseudomonas fluorescens and Echerichia coli. Clay particle wettability was determined by particle surface thermodynamic properties. Both kaolinite and Na-montmorillonite exhibited a monopolar surface and the monopolarity decreased after lipopolysaccharide coating, indicating an increase in hydration or surface wetness. The origins of interactions of clay particles with water molecules were discussed and related to clay particle water wettability.     

Robust hydrophobic surfaces displaying different surface roughness scales while maintaining the same wettability

A range of surfaces coated with spherical silica particles, covering the size range from nanometer to micrometer, have been produced using Langmuir-Blodgett (LB) deposition. The particles were characterized both in suspension and in the Langmuir trough to optimize the surface preparation procedure. By limiting the particle aggregation and surface layer failures during the preparation steps, well-defined monolayers with a close-packed structure have been obtained for all particle sizes. Thus, this procedure led to structured surfaces with a characteristic variation in the amplitude and spatial roughness parameters. In order to obtain robust surfaces, a sintering protocol and an AFM-based wear test to determine the stability of the deposited surface layer were employed. Hydrophobization of the LB films followed by water contact angle measurements showed, for all tested particle sizes, the same increase in contact angle compared to the contact angle of a flat hydrophobic surface. This indicates nearly hexagonal packing and gives evidence for nearly complete surface wetting of the surface features.     

Inversion of silica-stabilized emulsions induced by particle concentration

Emulsions of equal volumes of a cyclic silicone oil and water stabilized by fumed silica nanoparticles alone can be inverted from oil-in-water (o/w) to water-in-oil (w/o) by simply increasing the concentration of particles. The phenomenon is found to be crucially dependent both on the inherent hydrophobicity of the particles and on their initial location. Inversion only occurs in systems with particles of intermediate hydrophobicity when dispersed in oil; emulsions prepared from the same particles but initially dispersed in water remain o/w at all particle concentrations. The stability and drop size distributions in the different emulsions are compared. Various hypotheses are put forward and argued to explain this novel inversion route including adsorption of oil onto particle surfaces, hysteresis of contact angle affecting particle wettability in situ, and the structure of particle dispersions in oil or water prior to emulsification inferred from rheology and light scattering measurements. We propose that the tendency for particles to behave more hydrophobically at higher concentrations in oil is due to the reduction in the effective silanol content at their surfaces as a result of gel formation via silanol-silanol hydrogen bonds. In water, solvation of particle surfaces prevents this from occurring and particles behave as hydrophilic ones at all concentrations. A concentration-induced change in particle wettability is thus advanced.     

Molecular dynamics simulations of water droplets on polymer surfaces

Molecular dynamics simulations were used to study the wetting of polymer surfaces with water. Contact angles of water droplets on crystalline and two amorphous polyethylene (PE) and poly(vinyl chloride) (PVC) surfaces were extracted from atomistic simulations. Crystalline surfaces were produced by duplicating the unit cell of an experimental crystal structure, and amorphous surfaces by pressing the bulk polymer step by step at elevated temperature between two repulsive grid surfaces to a target density. Different-sized water droplets on the crystalline PE surface revealed a slightly positive line tension on the order of 10(-12)-10(-11) N, whereas droplets on crystalline PVC did not yield a definite line tension. Microscopic contact angles produced by the simple point charge (SPC) water model were mostly a few degrees smaller than those produced by the extended SPC model, which, as the model with lowest bulk energy, presents an upper boundary for contact angles. The macroscopic contact angle for the SPC model was 94 degrees on crystalline PVC and 113 degrees on crystalline PE. Amorphicity of the surface increased the water contact angle on PE but decreased it on PVC, for both water models. If the simulated contact angles on crystalline and amorphous surfaces are combined in proportion to the crystallinity of the polymer in question, simulated values in relatively good agreement with measured values are obtained.     

Enhanced hydrophobicity of rough polymer surfaces

Molecular dynamics simulations were used to study the effect of periodic roughness of PE and PVC polymer surfaces on the hydrophobicity. Pillars of different lateral dimensions and heights were derived from flat crystalline surfaces, and the results of nanoscale simulations on the structured surfaces were compared with theoretical predictions of the Wenzel and Cassie equations. Hydrophobicity increased on all rough surfaces, but the increase was greater on the structured PE surfaces because of the larger water contact angle on the flat PE surface than the corresponding PVC surface. Equally sized pillar structures on the two polymers resulted in different equilibrium wetting geometries. Composite contacts were observed on rough PE surfaces, and the contact angle increased with decreasing contact area between the solid and the liquid. Opposite results were obtained for rough PVC surfaces; the contact angle increased with the solid-liquid contact area, in agreement with Wenzel's equation. However, the composite contact was observed if the energies of the wetted and composite contacts were almost equal. Good agreement was obtained between the simulated contact angles and equilibrium droplet shapes and the theories but there were also some limitations of the nanoscale simulations.     

Effect of deposition parameters on the wettability and microstructure of superhydrophobic films with hierarchical micro-nano structures

Superhydrophobic films with hierarchical micro-nano structures were deposited on glass substrates by solution immersion method from a solution containing cobalt chloride, urea and cetyl trimethyl ammonium bromide (CTAB). Subsequently the films were hydrophobized with a low surface energy material like octadecanoic acid under ambient conditions resulting in superhydrophobic surfaces with water contact angle (WCA) of about 168° and contact angle hysteresis of 1°. The effect of deposition parameters such as solution composition, temperature, deposition time and alkanoic acid treatment on surface morphology and wettability of the films was studied. Mechanism of formation of cobalt chloride carbonate hydroxide film is discussed. Addition of CTAB to the solution resulted in a change in the surface morphology of the deposited films with flower-like structures. The wettability of films obtained under different process conditions was correlated to surface roughness using Wenzel and Cassie models.     

Amphiphilic copolymer grafted "smart surface" enhanced by surface roughness

Polystyrene-poly(acrylic acid) (PS-PAA) block copolymers polymerized by atom transfer radical polymerization were covalently grafted to both smooth and microtextured surfaces. These amphiphilic copolymers were utilized to create smart surfaces, which can be responsive to external stimuli, e.g., pH values or organic solvent. Atom force microscopy, field emission scanning electron microscopy, and contact angle measurements were employed to investigate the physiochemical features of the copolymer brushes. It was found that the wettability of surfaces depended on both the PS/PAA molar ratio and external solvent properties. Hydrophilic surfaces were obtained after treatment with basic solution, as well as a polar solvent, such as ethanol. With treatment with acidic solution or toluene, the surface could be reversibly turned relatively hydrophobic, probably due to the rearrangement or reorganization of polymer chains. Moreover, rougher surfaces, which were microtextured by ZnO nanorods, were incorporated into this adaptive system to enhance the tunable range of wettability.     

Particle zips: vertical emulsion films with particle monolayers at their surfaces

Vertical emulsion films with particle monolayers at their surfaces have been studied by direct microscope observations. The effects of particle wettability and surface coverage on the structure and stability of water films in octane and octane films in water have been investigated. Monodisperse silica particles (3 microm in diameter) hydrophobized to different extents have been used. It is found that the structure and stability of emulsion films strongly depend on the film type (water-in-oil or oil-in-water), the particle contact angle, the interactions between particles from the same and the opposite monolayer, and the monolayer density. Stable films are observed only when the particle wettability fulfills the condition for stable particle bridges--in agreement with the concept that hydrophilic particles can give stable oil-in-water emulsions, whereas hydrophobic ones give water-in-oil emulsions. In the case of water films with dilute disordered monolayers at their surfaces, the hydrophilic particles are expelled from the film center toward its periphery, giving a dimple surrounded by a ring of particles bridging the film surfaces. In contrast, the thinning of octane films with dilute ordered monolayers at their surfaces finally leads to the spontaneous formation of a dense crystalline monolayer of hydrophobic particles bridging both surfaces at the center of the film. The behaviors of water and octane films with dense close-packed particle monolayers at their surfaces are very similar. In both cases, a transition from bilayer to bridging monolayer is observed at rather low capillary pressures. The implications of the above finding for particle stabilized emulsions are discussed.     

Fabrication of hydrophobic surfaces by coupling of Langmuir-Blodgett deposition and a self-assembled monolayer

A novel method coupling the Langmuir-Blodgett (LB) deposition of silica particles and the formation of a self-assembled monolayer (SAM) of alkylsilane is proposed for fabricating hydrophobic surfaces. The LB deposition and the SAM are supposed to confer the substrate surface roughness and low surface energy, respectively. By controlling the hydrophobic-hydrophilic balance of the silica particle surface through the adsorption of surfactant molecules, deposition of monolayers consisting of hexagonally close-packed arrays of particles on a glass substrate can then be successfully conducted in a Langmuir trough. LB particulate films with a particle layer number up to 5 were thereby prepared. A sintered and hydrophobically finished particulate film with roughness factor of 1.9 was finally fabricated by sintering and surface silanization. Effects of particle size and particle layer number on the wetting behavior of the particulate films were systematically studied by measuring static and dynamic water contact angles. The experimental results revealed that a static contact angle of about 130 degrees resulted from the particulate films regardless of the particle size and particle layer number. This is consistent with the predictions of both the Wenzel model and the Cassie and Baxter model in that roughness of a hydrophobic surface can increase its hydrophobicity and a switching of the dominant mode from Wenzel's to Cassie and Baxter's. In general, an advancing contact angle of about 150 degrees , a receding contact angle of about 110 degrees , and a contact angle hysteresis of about 40 degrees were exhibited by the particulate films fabricated.     

Wetting of nanogrooved polymer surfaces

Molecular dynamics simulations were used to study the wetting of nanogrooved PE and PVC polymer surfaces. The contact angles, equilibrium states, and equilibrium shapes of two nanosized water droplets were analyzed on surfaces with 1D-arranged periodic roughness of various dimensions. The composite solid-liquid contact, which is preferred in practical applications and in which a droplet rests on top of the surface asperities, was observed on the roughest PE surfaces, whereas water filled the similar but slightly deeper grooves on PVC surfaces. The transition from the wetted to composite contact regime occurred when the contact angle with a flat surface reached the value at which the apparent Wenzel and Cassie contact angles are equal. Droplets on grooved PE surfaces with the composite contact exhibited contact angles in agreement with Cassie's equation, but the increase in hydrophobicity on smoother surfaces with the wetted contact was less than expected from Wenzel's equation. The difference between the simulated and theoretical values decreased as the dimensions of the surface grooves increased. Only a slight increase or even a slight decrease in the contact angles was observed on the grooved PVC surfaces, owing to the less hydrophobic nature of the flat PVC surface. On both polymers, the nanodroplet assumed a spherical shape in the composite contact. Only minor anisotropy was observed in the wetted contact on PE surfaces, whereas even a highly anisotropic shape was seen on the grooved PVC surfaces. The contact angle in the direction of the grooves was smaller than that in the perpendicular direction, and the difference between the two angles decreased with the increasing size of the water droplet.     

Particle adsorption in evaporating droplets of polymer latex dispersions on hydrophilic and hydrophobic surfaces

Stain patterns formed by drying up of droplets of polymer latex dispersion on hydrophilic and hydrophobic surfaces were examined in light of the mechanism of particle adsorption in evaporating droplets. On hydrophilic surfaces, the volume of droplets decreased with time, keeping the initial outline of contact area, and circular stain patterns were formed after the dry-up of droplets. By the microscopic observation of particles in the droplets, it was found that a large portion of the particles were forced to adsorb on the outline of the contact area where a microscopic thin water layer was formed because of hydrophilicity of the surface. On hydrophobic surfaces, on the other hand, the contact area of droplets decreased as evaporation proceeded, while no particle was adsorbed on the surface at the early stages. The particles in the droplets started to aggregate when the concentration of particles reached a critical value, and the aggregates adsorbed on the surface forming tiny spots after the dry-up. Time evolutions of contact angle, contact area and volume of the droplets were analyzed in light of differences in the adsorption mechanisms between hydrophilic and hydrophobic surfaces. Received: 14 January 1998 Accepted: 1 May 1998     

Theoretical evaluation of nano- or microparticulate contact angle at fluid/fluid interfaces: analysis of the excluded area behavior upon compression

A novel method for the determination of the particle contact angle at the liquid/gas or liquid/liquid interface based on the excluded area concept revealed, in spite of its simplicity, some serious difficulties connected with the exact quantitative particle deposition at the interface and with changes in the particulate contact angle upon binary monolayer compression. The comprehensive theoretical consideration of the contact angle behavior made for such a system allowed considerable improvements: firstly, the prediction of direction of the particles' displacement at surface pressure increase is now possible and hence an unambiguous identification of particle hydrophobicity can be done. Secondly, the analytical relation describing the dependence of the particulate contact angle on the surface tension (surface pressure) was derived, allowing the prediction of whether or not particles of a given hydrophobicity will be expelled from the monolayer at certain surface pressure and of the area relinquished by the displaced particles. Thirdly, the transformation of this relation upon taking into consideration the initial conditions led to a linear dependence between excluded area and normalized surface tension allowing the determination of the particle contact angle and the exact number of deposited particles simultaneously and independently of each other. Finally, the application of the improved approach to the previously collected experimental data yielded reasonable values for both particle contact angle and number of deposited particles.     

Surface study of sintered alumina substrates using solution‐processed ZnO nanorods as a microscopic wettability indicator

Wettability and its distribution are crucial factors that indicate the surface conditions of substrates. We report a surface study of sintered alumina substrates using solution‐processed ZnO nanorods as a microscopic wettability indicator. The alumina substrates comprising of micrometer‐sized sintered grains were treated separately with ultraviolet/ozone (dry process) or ozone water (wet process), and their surface conditions were characterized by conventional surface analysis methods, such as water contact angle, X‐ray photoelectron spectroscopy and grazing angle attenuated total reflection Fourier transform infrared spectroscopy. The results showed that the alumina substrates treated with ultraviolet/ozone and ozone water had distinct clean surfaces compared to those without treatments, but no significant differences were noted between these two ozone‐based treatments. Then, as a wettability‐sensitive deposition technique, Pd‐catalyzed chemical deposition of ZnO nanorods was performed on the alumina substrates, which involved dip coating of Pd nanoparticles on the substrates in aqueous solutions, followed by the chemical solution growth of ZnO. Vertically aligned ZnO nanorods of ~85 nm in diameter were densely formed along a rough surface of the substrates. Morphological uniformity of the nanorods varied depending on the treatment condition; local surfaces with sufficient wettability provided uniform nanorods but those with insufficient wettability gave irregular nanorods, making the visualization of the microscopic surface wettability possible. Copyright © 2016 John Wiley & Sons, Ltd.     

Fabrication of flexible gold films with periodic sub-micrometer roughness and their wettability control by modification of SAM

Flexible honeycomb gold films supported by polymer sheets are fabricated by using polystyrene particle monolayers. The surfaces of the flexible gold films are covered with self-assembled monolayers (SAMs) of hydrophobic or hydrophilic thiol compounds, and the wettability of the modified surface is evaluated by measurements of the contact angles of water droplets. The contact angle of the film covered with hydrophobic SAM is ca. 150 degrees, which is greater than the value of 112 degrees for a flat gold surface, while the values for hydrophilic SAM are below 10 degrees.     

Influence of nanoscale particle roughness on the stability of pickering emulsions

The wetting behavior of solid surfaces can be altered dramatically by introducing surface roughness on the nanometer scale. Some of nature's most fascinating wetting phenomena are associated with surface roughness; they have inspired both fundamental research and the adoption of surface roughness as a design parameter for man-made functional coatings. So far the attention has focused primarily on macroscopic surfaces, but one should expect the wetting properties of colloidal particles to be strongly affected by roughness, too. Particle wettability, in turn, is a key parameter for the adsorption of particles at liquid interfaces and for the industrially important use of particles as emulsion stabilizers; yet, the consequence of particle roughness for emulsion stability remains poorly understood. In order to investigate the matter systematically, we have developed a surface treatment, applicable to micrometer-sized particles and macroscopic surfaces alike, that produces surface coatings with finely tunable nanoscale roughness and identical surface chemistry. Coatings with different degrees of roughness were characterized with regard to their morphology, charging, and wetting properties, and the results were correlated with the stability of emulsions prepared with coated particles of different roughness. We find that the maximum capillary pressure, a metric of the emulsions' resistance to droplet coalescence, varies significantly and in a nonmonotonic fashion with particle roughness. Surface topography and contact angle hysteresis suggest that particle roughness benefits the stability of our emulsions as long as wetting occurs homogeneously (Wenzel regime), whereas the transition toward heterogeneous wetting (Cassie-Baxter regime) is associated with a loss of stability.