FT‐IR Studies of Plasticization of Propylene Carbonate and Ethylene Carbonate in PEO‐NaSCN Polymer Electrolytes

The FT‐IR spectra of poly(ethylene oxide) (PEO)‐based gel polymer electrolytes (GPEs), PEO‐NaSCN‐propylene carbonate (PC) and PEO‐NaSCN‐ethylene carbonate (EC), were measured at room temperature. Along with the FT‐IR spectra of NaSCN‐PC, PEO‐PC, and PEO‐EC, the interactions in the GPEs and the plasticizations of PC and EC are revealed. It is shown that the coordination of ether oxygen in PEO with NaSCN is the preferential solvation, whereas the interactions of PC and EC with NaSCN are relatively weak in the GPEs. However, both PC and EC play an important role in inhibiting the formation of crystalline complexes and high ionic aggregations, in addition to the ability of transformation of PEO from crystal to amorphism. It is further observed that EC exhibits the stronger ability to transform PEO crystalline into amorphism than PC when the plasticizer content in PEO is more than 25%, and also the far stronger ability to decompose the crystalline complexes, in particular, in polymer electrolytes with high salt content.     

Highly ion conductive poly(ethylene oxide)-based solid polymer electrolytes from hydrogen bonding layer-by-layer assembly

We report the development of a solid polymer electrolyte film from hydrogen bonding layer-by-layer (LBL) assembly that outperforms previously reported LBL assembled films and approaches battery integration capability. Films were fabricated by alternating deposition of poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) layers from aqueous solutions. Film quality benefits from increasing PEO molecular weight even into the 10(6) range due to the intrinsically low PEO/PAA cross-link density. Assembly is disrupted at pH near the PAA ionization onset, and a potential mechanism for modulating PEO:PAA ratio within assembled films by manipulating pH is discussed. Ionic conductivity of 5 x 10(-5) S/cm is achievable after short exposure to 100% relative humidity (RH) for plasticization. Adding free ions by exposing PEO/ PAA films to lithium salt solutions enhanced conductivity to greater than 10(-5) S/cm at only 52% RH and tentatively greater than 10(-4) S/cm at 100% RH. The excellent stability of PEO/PAA films even when exposed to 1.0 M salt solutions led to an exploration of LBL assembly with added electrolyte present in the adsorption step. Fortuitously, the modulation of PEO/PAA assembly by ionic strength is analogous to that of electrostatic LBL assembly and can be attributed to electrolyte interactions with PEO and PAA. Dry ionic conductivity was enhanced in films assembled in the presence of salt as compared to films that were merely exposed to salt after assembly, implying different morphologies. These results reveal clear directions for the evolution of these promising solid polymer electrolytes into elements appropriate for electrochemical power storage and generation applications.     

Ion conducting properties of poly(ethylene oxide)-based electrolytes incorporating amorphous silica attached with imidazolium salts

Poly(ethylene oxide) (PEO)-based polymer electrolytes containing amorphous silica attached ionic liquid (IL) were studied in order to improve electrochemical and interfacial properties. An imidazolium salt such as IL was attached to modified ceramic fillers. The modified ceramic fillers were amorphous silica with the immobilized 1-methyl-3-propyl-imidazolium bromide (MPIm-AS). PEO-based polymer electrolytes were prepared by using the solution casting technique. In order to investigate the ionic conductivity, studies on the modified filler addition effects on the ion-conducting behavior of polymer electrolytes having specific amounts of MPIm-AS were carried out. The addition of MPIm-AS in polymer electrolytes has resulted in higher ionic conductivity at room temperature. The structure, crystallinity, and morphology of the solid polymer electrolytes were evaluated using X-ray diffraction, differential scanning calorimetry, and scanning electron microscope measurement. The ionic conductivity was measured by an AC impedance method. The enhanced conductivity was dependent on the decreased crystallinity and the changed morphologies of composites.     

聚合物单阳离子导体的制备—羧酸型梳状单离子导体

本文报道一种制备聚合物单阳离子导体的新方法。马来酸酐－醋酸乙烯酯及马来酸酐－苯乙烯共聚物以聚乙二醇单甲醚醇解，使酸酐环打开而得到带有聚乙二醇侧链的羧酸型梳状聚合物，其锂盐在加入适当增塑剂成膜后，可作为聚合物单阳离子导体，其结构以非晶态为主，具有较低的玻璃化转变温度及较好的热稳定性，增塑后的室温电导率最高可达１０＾－６Ｓ／ｃｍ。此外还研究了聚合物结构、阳离子半径、增塑剂、温度及外加额率等因素对电导率     

Vibrational spectroscopic study of ionic association in poly(ethylene oxide)-NH4SCN polymer electrolytes

The polymer-ammonium complexes are an important class of proton conducting polymer electrolytes. In this work, poly(ethylene oxide) (PEO)-NH(4)SCN electrolytes were prepared over a large range of the salt content, and their FT-IR spectra were measured at room temperature. Based on the assignments of each band in the spectral envelope of SCN(-1), their relative intensities are determined by the use of FT-IR technique. Following the experimental results and spectral analyses, this paper reports the interactions, the various ionic associations, the changes of the ionic association with NH(4)SCN content, and the characteristics of structure in PEO-NH(4)SCN electrolytes. It is shown that the hydrogen bonds of PEO and NH(4)SCN exert the great effect to the ionic association, the interactions of PEO with NH(4)SCN, and PEO crystallinity, in particular, under the condition of high NH(4)SCN content. In addition, the differences of ionic association among PEO-NaSCN, PEO-KSCN and NH(4)SCN electrolytes are also compared in this paper.     

PEO/LiClO_4纳米SiO_2复合聚合物电解质的电化学研究

将实验室制备的纳米二氧化硅和市售纳米二氧化硅粉末与PEO LiClO4复合 ,制得了复合PEO电解质 .它们的室温离子电导率可比未复合的PEO电解质提高 1～ 2个数量级 ,最高可以达到 1 2 4× 10 - 5S cm .离子电导率的提高有两方面的原因 :一是无机二氧化硅粉末的加入抑制了PEO的结晶 ,是二氧化硅粉末和聚合物电解质之间形成的界面对电导率的提高也有一定的作用 .在进一步加入PC EC(碳酸丙烯酯 碳酸乙烯酯 )混合增塑剂后制得的复合凝胶PEO电解质 ,可使室温离子电导率再提高 2个数量 ,达到 2× 10 - 3 S cm .用这种复合凝胶PEO电解质组装了Li|compositegelelectrolyte|Li半电池 ,并测量了该半电池的交流阻抗谱图随组装后保持时间的变化 ,实验观察到在保持时间为 144h以内钝化膜的交流阻抗迅速增大 ,但在随后的时间内逐渐趋于平稳 ,表明二氧化硅粉末的加入可以有效地抑制钝化膜的生长     

聚氧化乙烯基聚合物电解质中离子缔合与结晶状态的傅立叶变换红外光谱(FTIR)研究

通过FTIR光谱技术对P(EO)_nLiX [X＝N(SO₂CF₃)₂, SCN, ClO₄] (n＝4～60)聚合物电解质的离子缔合行为进行了研究, 结果表明在PEO-LiSCN体系中缔合现象较为严重. 在高浓度时LiSCN主要以离子对、离子簇以及二聚体形式存在, 自由离子含量较少. 而对于LiTFSI和LiClO₄体系, 则以自由离子形式为主. 随着锂盐的加入, 由于其阴离子的增塑作用使聚氧化乙烯(PEO)中的晶相成分逐渐向无定形相转化. 当锂盐含量增加到一定程度, 体系中会有不同晶相复合物的形成.     

聚氧乙烯超薄膜中构象变化的红外光谱研究

近年来 ,有关聚合物薄膜的研究受到了广泛关注 .低维数高分子超薄膜的各种行为由于涉及到高分子运动的动力学、热力学本质而逐渐成为高分子科学研究中的一大热点 .实验结果表明[1～ 3] ,几何受限条件和基板对于聚合物薄膜结晶的形态及性能都会产生显著影响 .广角 X射线衍射实验和自由表面的掠入射 X射线实验 [4 ]表明 ,有些在本体中呈现液晶有序的聚酰亚胺在靠近基板附近变得更加有序 .Despotopoulou等 [5] 对聚二正己基硅烷在超薄膜中构象扰动的观察发现 ,当膜厚小于 2 0 0 nm时 ,聚二正己基硅烷的侧链变得无序 ,傅里叶变换红外光谱测试…     

Elastomeric flexible free-standing hydrogen-bonded nanoscale assemblies

Poly(ethylene oxide) (PEO) is a key material in solid polymer electrolytes, biomaterials, drug delivery devices, and sensors. Through the use of hydrogen bonds, layer-by-layer (LBL) assemblies allow for the incorporation of PEO in a controllable tunable thin film, but little is known about the bulk properties of LBL thin films because they are often tightly bound to the substrate of assembly. The construction technique involves alternately exposing a substrate to a hydrogen-bond-donating polymer (poly(acrylic acid)) and a hydrogen-bond-accepting polymer (PEO) in solution, producing mechanically stable interdigitated layers of PEO and poly(acrylic acid) (PAA). Here, we introduce a new method of LBL film isolation using low-energy surfaces that facilitate the removal of substantial mass and area of the film, allowing, for the first time, the thermal and mechanical characterization that was previously difficult or impossible to perform. To further understand the morphology of the nanoscale blend, the glass transition is measured as a function of assembly pH via differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The resulting trends give clues as to how the morphology and composition of a hydrogen-bonded composite film evolve as a function of pH. We also demonstrate that LBL films of PEO and PAA behave as flexible elastomeric blends at ambient conditions and allow for nanoscale control of thickness and film composition. Furthermore, we show that the crystallization of PEO is fully suppressed in these composite assemblies, a fact that proves advantageous for applications such as ultrathin hydrogels, membranes, and solid-state polymer electrolytes.     

红外光谱研究PEO基离子液体聚合物电解质

以聚氧化乙烯(PEO)为聚合物基体, 双三氟甲基磺酸亚酰胺锂(LiTFSI)为锂盐, 加入不同量的离子液体(BMIMPF₆)为增塑剂, 制备离子液体聚合物电解质. 运用发射FTIR光谱技术实时监测所制备聚合物电解质的结构随温度的变化. 结合FTIR透射光谱\, SEM和XRD的研究结果分析了离子液体对离子电导率的影响, 并初步提出离子导电增强机制.     

Ionic conductivities of the complexes of LiClO4 and alternating copolymers of oligomeric poly(ethylene oxide) having biphenyl units in the backbone

A series of copolymers of predominantly poly(ethylene oxide) (PEO) with biphenyl (BP) units in the backbone were synthesized. The solid polymer electrolytes (SPEs) were prepared from these copolymers (BP-PEG) employing lithium perchlolate (LiClO₄) as a lithium salt and their ionic conductivities were investigated to exploit the structure–ionic conductivity relationships as a function of chain length ratio between the flexible PEO chains and rigid BP units. The ionic conductivity increases with increasing PEO length in BP-PEG. The salt concentrations in BP-PEG/LiClO₄ complexes were also changed and the results show that maximum conductivity is obtained at [EO]/[Li⁺]≈8. The reasons for these findings are discussed in terms of the number of charge carriers and the mobility of the polymer chain.     

Molecular dynamics simulation of polymer electrolytes based on poly(ethylene oxide) and ionic liquids. II. Dynamical properties

Dynamical properties of polymer electrolytes based on poly(ethylene oxide) (PEO) and ionic liquids of 1-alkyl-3-methylimidazolium cations were calculated by molecular dynamics simulations with previously proposed models [L. T. Costa and M. C. Ribeiro, J. Chem. Phys. 124, 184902 (2006)]. The effect of changing the ionic liquid concentration, temperature, and the 1-alkyl-chain lengths, [1,3-dimethylimidazolium]PF(6) and [1-butyl-3-methylimidazolium]PF(6) ([dmim]PF(6) and [bmim]PF(6)), was investigated. Cation diffusion coefficient is higher than those of anion and oxygen atoms of PEO chains. Ionic mobility in PEO[bmim]PF(6) is higher than in PEO[dmim]PF(6), so that the ionic conductivity kappa of the former is approximately ten times larger than the latter. The ratio between kappa and its estimate from the Nernst-Einstein equation kappa/kappa(NE), which is inversely proportional to the strength of ion pairs, is higher in ionic liquid polymer electrolytes than in polymer electrolytes based on inorganic salts with Li(+) cations. Calculated time correlation functions corroborate previous evidence from the analysis of equilibrium structure that the ion pairs in ionic liquid polymer electrolytes are relatively weak. Structural relaxation at distinct spatial scales is revealed by the calculation of the intermediate scattering function at different wavevectors. These data are reproduced with stretched exponential functions, so that temperature and wavevector dependences of best fit parameters can be compared with corresponding results for polymer electrolytes containing simpler ions.     

Influence of Humidity on the Complex Structure of PEO-Lithium Salt Polymer Electrolyte

Solid polymer electrolytes of PEO/LiClO₄ and PEO/LiTFSI solution casting films were prepared with the EO/Li molar ratio of 3: 1, and the effect of relative humidity (RH) on their complex structures were characterized. It is shown that the complex structures were barely changed at RH ≤ 10% while severe differences were shown at RH ≥ 20%. The reason was attributed to the interactions of water with lithium salt, and the formation of PEO–Li⁺–H₂O decreased the interactions between PEO and lithium ions. Furthermore, it was shown that the hydrated samples after heat treatment were still strikingly different in characters from their anhydrous precursors, and the type of lithium salt affected the final structures. It was found that the structure of (PEO)₃LiClO₄ (30% RH) was hardly changed after heating; however, an irreversible compositional transition was discovered in (PEO)₃LiTFSI (30% RH) in which case (PEO)₂LiTFSI was formed.     

Role of plasticizer's dielectric constant on conductivity modification of PEO-NH4F polymer electrolytes

The addition of plasticizer to the polyethylene oxide (PEO)-ammonium fluoride (NH₄F) polymer electrolytes has been found to result in an increase in conductivity value and the magnitude of increase has been found to depend upon the dielectric constant of the plasticizer used. The addition of dimethylacetamide as a plasticizer with dielectric constant (?=37.8) higher than that of PEO (?∼5) results in an increase of conductivity by more than three orders of magnitude whereas the addition of diethylcarbonate as a plasticizer with dielectric constant (?=2.82) lower than that of PEO does not enhance the conductivity of PEO-NH₄F polymer electrolytes. The increase in conductivity has further been found to depend upon the concentration of plasticizer, the concentration of salt in the polymer electrolyte as well as on the dielectric constant value of the plasticizer used. The conductivity modification with the addition of plasticizer has been explained on the basis of dissociation of ion aggregates formed in PEO-NH₄F polymer electrolytes at higher salt concentrations.     

Conformation dependence of electronic structures of poly(ethylene oxide)

The electronic structure of pure poly(ethylene oxide) (PEO) for four different polymeric chain conformations has been studied by Hartree-Fock (HF) and density functional theory (DFT) through the analysis of their valence band photoelectron spectroscopy (VB-PES), X-ray emission spectroscopy (XES), and resonant inelastic X-ray scattering (RIXS). It is shown that the valence band of PEO presents specific conformation dependence, which can be used as a fingerprint of the polymeric structures. The calculated spectra have been compared with experimental results for PEO powder.     

含烷氧磺酸锂盐及对称星形醚的聚环氧乙烷基聚合物电解质的制备及电化学性能

合成了低聚度烷氧磺酸锂盐（LiSA(EO)n)和对称星形醚（STEO）增塑剂,并制备了聚环氧乙烷（PEO）基聚合物电解质。 研究了PEO16+LiSA(EO)n体系的锂离子迁移数和电导率与锂盐结构的关系,实验结果表明,LiSA(EO)n代替LiClO4作为锂盐时,其电导率得到提高,而且聚合物电解质的锂离子迁移数随着烷氧磺酸锂盐阴离子体积的增大而增加,并且其中PEO16+LiSA(EO)2体系的锂离子迁移数达到0.35。 STEO可明显地提高PEO16-LiSAEO-STEO体系的电导率,PEO16-LiSAEO-20%STEO室温电导率可达到0.5×10-4 S/cm。 通过DSC实验结果表明,STEO的加入,可有效降低聚合物电解质体系的熔融温度和结晶度,PEO16-LiSAEO-20%STEO电化学稳定窗口在4.4 V以上,可满足锂电池的应用要求。     

Effects of PEO length and phenyl unit structure on ionic conductivities of the complexes of LiClO4 and alternating copolymers of PEO having various phenyl units in the backbone

A series of copolymers of predominantly poly(ethylene oxide) (PEO) with mono-phenyl (HQ), biphenyl (BP) units, or both of them (HQ/BP) in the backbone were synthesized. The solid polymer electrolytes (SPEs) were prepared from three different types of copolymers (HQ-PEG, BP-PEG, and HQ/BP-PEG) employing lithium perchlorate (LiClO₄) as a lithium salt at a fixed salt concentration of [EO]/[Li⁺]=8. Their ionic conductivities were investigated to exploit the structure–ionic conductivity relationships as a function of structural change in rigid phenyl units and chain length ratio between flexible PEO chain and rigid phenyl units. As more rigid phenyl units were incorporated in the backbone chain, the formation inter- and intra-molecular complex with LiClO₄ became weaker and lower ionic conductivities were observed. And it was also found that higher ionic conductivity is obtained with increasing PEO chain length because inter- and intra-molecular dissociation power of PEO increases.     

Optical Spectra of Polygermane/Mesoporous Silica Nanocomposites

Summary: The monitoring of poly(di-n-hexylgermane) (PDHG) optical spectra in a variety of structures ranging from a bulk film to a nanosize polymer confined into a nanopore of SBA-15 was performed using the fluorescence and fluorescence excitation spectra in the temperature range from 5 to 240 K as well as the absorption and FTIR spectra at room temperature. The observed data were compared with those obtained for poly(di-n-hexylsilane). It was shown that PDHG film absorption and fluorescence spectra strongly depend on the polymer thickness and consist of a number of bands which were assigned to centers with different amount of trans- and gauche- conformers of the polymer chains. Conformations of the polymer chains found in a thin film and in a 10 nm pore are similar while differing from the conformations of a thick film. Optical spectra of the confined PDHG are blue-shifted relative to those of a thin film. The PDHG polymer chain conformation becomes disordered with the decrease of the polymer film thickness and the nanopore size from 10 to 6 nm.     

High ionic conductivity P(VDF-TrFE)/PEO blended polymer electrolytes for solid electrochromic devices

Solid polymer electrolytes with excellent ionic conductivity (above 10(-4) S cm(-1)), which result in high optical modulation for solid electrochromic (EC) devices are presented. The combination of a polar host matrix poly(vinylidene fluoride-trifluoroethylene) P(VDF-TrFE) and a solid plasticized of a low molecular weight poly(ethylene oxide) (PEO) (M(w)≤ 20,000) blended polymer electrolyte serves to enhance both the dissolution of lithium salt and the ionic transport. Calorimetric measurement shows a reduced crystallization due to a better intermixing of the polymers with small molecular weight PEO. Vibrational spectroscopy identifies the presence of free ions and ion pairs in the electrolytes with PEO of M(w)≤ 8000. The ionic dissolution is improved using PEO as a plasticizer when compared to liquid propylene carbonate, evidently shown in the transference number analysis. Ionic transport follows the Arrhenius equation with a low activation energy (0.16-0.2 eV), leading to high ionic conductivities. Solid electrochromic devices fabricated with the blended P(VDF-TrFE)/PEO electrolytes and polyaniline show good spectroelectrochemical performance in the visible (300-800 nm) and near-infrared (0.9-2.4 μm) regions with a modulation up to 60% and fast switching speed of below 20 seconds. The successful introduction of the solid polymer electrolytes with its best harnessed qualities helps to expedite the application of various electrochemical devices.     

含硅氢键聚二硅氧烷/聚醚共混聚合物电解质 II. PSEMH对PEO结晶性能及离子电导率的影响

通过Raman,DSC和XRD等方法对PEO-PSEMH-LiClO4全固态共混聚合物电解质进行了研究,结果表明PSEMH能够显著地降低PEO-LiClO4电解质体系的PEO的结晶性和玻璃化转变温度,同时PSEMH分子的二硅醚链节中氧原子与Li+间具有配位作用,从而大幅提高x%PEO-y%PSEMH-LiClO4电解质在低温区的离子电导率。而当PSEMH交联硫化之后,虽然降低了PEO的结晶度和Tg,但是由于PSEMH的交联网络限制了聚合物链段的运动性,使得电解质的离子电导率在低温区高于100%PEO-LiClO4(约为12倍),而在高温区则低于100%PEO-LiClO4,充分证明了PSEMH对电解质的离子电导率的具有显著的贡献作用。