Direct flame solid sampling for atomic absorption spectrometry: determination of copper in bovine liver

In this work a new device for the direct introduction of solid samples into flame atomizers is proposed. The determination of copper in bovine liver reference material by flame atomic absorption spectrometry (FAAS) using a conventional air–acetylene flame was chosen as an example. Between 0.05 and 0.50 mg of the test sample was weighed directly into a small polyethylene vial connected to a glass chamber. A flow of air carries the test sample as a dry aerosol to a T-shaped quartz cell positioned above the burner in the optical path. The atomic vapor generated produces a transient signal of less than 3-s duration; integrated absorbance is used for signal evaluation. Optimized conditions for air flow rate, flame stoichiometry, etc., were evaluated. There was no statistical difference between the results from the proposed system, compared with those obtained by prior sample digestion and determination by conventional FAAS. No excessive grinding of the samples was required and samples with particle size less than 80 μm were used throughout. Background signals were always low and a characteristic mass of 1.5 ng was found for Cu. The proposed system allows the determination of 60 test samples in 1 h and it can be easily adapted to conventional atomic absorption spectrometers.     

Use of paper capsules for cadmium determination in biological samples by solid sampling flame atomic absorption spectrometry

In this study, a new device was applied for direct solid sampling flame atomic absorption spectrometry. It was used for trace determination of cadmium in biological samples (bovine and chicken liver). Test samples (0.5 to 7 mg) were weighed into small paper capsules, which were introduced into a quartz cell heated by an air-acetylene flame. Operational conditions for the proposed system were evaluated. There was no significant difference between the results obtained with the proposed system and those obtained after digestion and determination by conventional graphite furnace atomic absorption spectrometry. Good agreement was also obtained with the certified values of two reference materials. Background signals were always low. The characteristic mass was 0.34 ng and relative standard deviation was less than 8%. The limit of detection for the proposed procedure was 1.6 ng or 0.23 μg g^− 1 if a sample mass of 7 mg was used. Excluding the steps for sample preparation (drying, milling and weighing), the proposed system allows the determination of 40 test samples per hour and it can be easily adapted to conventional flame atomic absorption spectrometers.     

On-line microwave oven digestion flame atomic absorption analysis of solid samples

A manifold has been developed for on-line microwave oven digestion and flame atomic absorption spectrometric (FAAS) determination of metallic elements in solid samples. The use of a closed flow system permits sample treatment before analysis by FAAS, the direct injection of slurries avoids a filtration step and the interconnection of two conventional rotary injection valves allows the rapid introduction of samples and standards. The determination of lead in sewage sludge was employed as a test system for the proposed on-line sample digestion manifold. The procedure has a limit of detection of 0.2 μg Pb g^?1.     

Comparison Studies on Several Ligands Used in Determination of Cd(II) in Rice by Flame Atomic Absorption Spectrometry after Ultrasound-Assisted Dispersive Liquid–Liquid Microextraction

Ligands plays an important role in the extraction procedures for the determination of cadmium in rice samples by using flame atomic absorption spectrometry (FAAS). In the present study, comparative evaluation of 10 commercially available ligands for formation of Cd(II)-ligand complex and determination of cadmium in rice samples by ultrasound-assisted dispersive liquid–liquid microextraction (UADLLME) combined with FAAS was developed. Sodium diethyldithiocarbamate (DDTC) provided a high distribution coefficient as well as a good absorbance signal, therefore DDTC was used as a ligand in UADLLME. A low density and less toxic solvent, 1-heptanol, was used as the extraction solvent and ethanol was used as the disperser solvent. In addition, the experimental conditions of UADLLME were optimized in standard solution first and then applied in rice, such as the type and volume of extractant and dispersant, pH, extraction time, and temperature. Under the optimal experimental conditions, the detection limit (3σ) was 0.69 μg/L for Cd(II). The proposed method was applied for the determination of Cd(II) in three different rice samples (polished rice, brown rice, and glutinous rice), the recovery test was carried out, and the results ranged between 96.7 to 113.6%. The proposed method has the advantages of simplicity, low cost, and accurate and was successfully applied to analyze Cd(II) in rice.     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

On-line electrolytic dissolution of solid metal samples and determination of copper in aluminium alloys by flame atomic absorption spectrometry

A flow-injection system was developed in which alloy metal samples are electrolytically dissolved and the dissolved samples are analysed by flame atomic absorption spectrometry (FAAS). The effects of electrolyte composition and electrolysis parameters on the dissolution of the sample were studied. The method was used for the determination of copper in aluminium alloys. Electrolyte solutions consisting of 0.2–1.0 M nitric acid are better than other electrolytes tested with regard to both alloy sample dissolution and determination of copper by FAAS. The peak height increases linearly with the electrolysis time or current within a certain range. The detection limit depends on the sensitivity of the detector used, and can be improved by increasing the electrolysis time or current. Generally, aluminium alloys containing 0.5–10% copper can give suitable signals for FAAS determination. The reproducibility of electrolysis and determination is about 4% for the same sampling points and 5% for different sampling points on the alloy sample.     

Determination of lead traces in water and liqueurs by derivative atom trapping flame atomic absorption spectrometry

 A new method for the direct determination of lead traces using derivative atom trapping flame atomic absorption spectrometry (DAT-FAAS) with an improved water-cooled stainless steel trapping equipment in an air-acetylene flame was investigated. The optimum conditions concerning the sensitivity were studied. For a 1 min collection, the characteristic concentration (given as derivative absorbance of 0.0044) and the detection limit (3s) were 1.4 ng/mL and 0.27 ng/mL, respectively. This is 361 and 74-fold better than those of the conventional flame atomic absorption spectrometry (FAAS) and comparable to those of graphite furnace atomic absorption spectrometry (GFAAS). The detection limit and sensitivity of DAT-FAAS for a 3 min collection time were 2 and 3 orders of magnitude higher than those of conventional FAAS. The present method was applied to the determination of lead in water and liqueur samples with a recovery range of 94–108% and a relative standard deviation of 3.5–5.6%. Received: 10 January 1996/Revised: 9 December 1996/Accepted: 20 December 1996     

Cadmium determination in biological samples by direct solid sampling flame atomic absorption spectrometry

A direct solid sampling flame atomic absorption spectrometric procedure for trace determination of cadmium in biological samples has been developed. Test samples (0.05–2.00 mg) were ground and weighed into small polyethylene vials, which were connected to the device for solid sample introduction into a conventional air/acetylene flame. Test samples were carried as a dry aerosol to a quartz cell, placed between the burner and the optical path, which had a perpendicular entrance and a slit in the upper part. The atomic vapor generated in the flame produced a transient signal that was totally integrated within 1 s. The effect of operating conditions and the extent of grinding on the analytical signal were evaluated. Background signals were always low and a characteristic mass of 0.29 ng Cd was obtained. Calibration was performed using different masses of solid certified reference materials. Results obtained for certified and in-house reference materials were typically within the 95% confidence interval of the certified and/or reference value, and the precision, expressed as relative standard deviation, was between 3.8 and 6.7%. The proposed system is simple and it might be adapted to conventional atomic absorption spectrometers allowing the determination of Cd in more than 80 test samples per hour, excluding weighing.     

Rapid separation on copper powder of total mercury in blood and determination of mercury by flameless atomic absorption spectrometry.

The determination of mercury in blood by flameless atomic absorption spectrometry (FAAS) has been described. Prior to its analysis, the sample was decomposed by combustion and separated on a copper powder micro-column. A special type of cell has been used which gives a better sensitivity compared with the types of cells described in the literature and the method of FAAS analysis has been improved. The sensitivity of 0.1 ng for 1% absorbance was observed and the standard deviation for six determinations at this level was found to be +/- 0.05 ng, for 95% probability.     

基于吸力洗脱的流动注射在线富集与火焰原子吸收联用测定水样中的镉

建立了一种基于吸力洗脱的流动注射(FI)在线富集与火焰原子吸收光谱法(FAAS)联用测定水样中痕量镉的新方法.洗脱过程依靠蠕动泵的吸力而不是推力实现洗脱剂的输送,明显降低了被分析物在洗脱过程中的分散,提高了原子吸收信号峰值(A),同时提高了富集系数(EF).进样流速6.0 mL/min;进样时间60 s,测定20 μg/L Cd2+,EF由传统方法的15提高到38;检出限为0.29 μg/L;测样频率为40个/h;相对标准偏差(RSD,n=11)为2.5%.以01‰ (V/V)的三乙醇胺(TEA)为掩蔽剂,Cd2+在水样中的回收率为93.8%～98.5%.     

Design and Critical Evaluation of Improved Electrothermal Vaporization Flame Atomic Absorption/Emission Spectrometry for Direct Determination of Trace Metals in Microliter Samples

Improved tantalum-filament electrothermal vaporization flame atomic absorption spectrometry (ETV-FAAS) was developed and used for the direct determination of trace metals in microliter samples. Studies have been made for optimizing the experimental parameters that affect the performance of sample introduction to the flame. Linear calibration graphs are shown for the elements Mn (10–200 ng), Pb (5–200 ng), Cu (5–100 ng), Cd (5–50 ng), Li (1–20 ng), Na (10–80 ng), and K (10–80 ng), using only 10 μl of standard solutions. The detection limits of the elements by ETV-FAAS were much lower than those of conventional FAAS. Absolute detection limits for all elements studied were less than 0.1 ng. The relative standard deviation values for the elements were <10%. The developed method was also applied to the determination of lead concentration in blood samples.     

Application of factorial design in optimization of preconcentration procedure for copper determination in soft drink by flame atomic absorption spectrometry

In the present paper, a procedure for preconcentration and determination of copper in soft drink using flame atomic absorption spectrometry (FAAS) is proposed, which is based on solid-phase extraction of copper(II) ions as its ion pair of 1,10-phenanthroline complexes with the anionic surfactant sodium dodecil sulphate (SDS), by Amberlite XAD-2 resin. The optimization process was carried out using 2^4–1 factorial and 2² factorial with a center point designs. Four variables (XAD-2 mass, copper mass, sample flow rate and elution flow rate) were regarded as factors in the optimization. Student's t-test on the results of the 2^4–1 factorial design with eight runs for copper extraction, demonstrated that the factors XAD-2 mass and sample flow rate in the levels studied are statistically significant. The 2² factorial with a center point design was applied in order to determine the optimum conditions for extraction. The procedure proposed allowed the determination of copper with detection limits (3/S) of 3.9 μg l⁻¹. The precision, calculated as relative standard deviation (R.S.D.) was 1.8% for 20.0 μg l⁻¹ of copper. The preconcentration factor was 100. The robustness of this procedure is demonstrated by the recovery achieved for determination of copper in the presence of several cations. This procedure was applied to the determination of copper in soft drink samples collected in Campinas, SP, Brazil.     

FLAME ATOMIC ABSORPTION DETERMINATION OF COPPER IN CEREALS FOOD SAMPLES WITH THE PRECONCENTRATION OF POTASSIUM TETRATITANATE WHISKER

A simple and reliable method has been developed for separation and preconcentration of trace amounts of copper ions in cereals food for subsequent measurement by flame atomic absorption spectrometry （FAAS）. The Cu^2＋ ions are adsorbed selectively and quantitatively during the passage. The retained copper ions were desorbed from the potassium tetratitanate whisker with 10.0mL of 2mol/L sulphuric acid solutions as eluent and were determined by FAAS. The linear range was 0.05μg/mL-0.20μg/mL in the original solution with a correlation coefficient of 0.9998. The detection limit of the proposed method is 2. lng/mL in the original solution （3σ, n=9）. Determination of copper in standard ions showed that the proposed method has good accuracy （recovery was more than 95%）. The method was successfully applied for recovery and determination of copper in cereals food samples     

Determination of cadmium in biological materials by flame atomic absorption spectrometry with flow-injection on-line sorption preconcentration

A new on-line preconcentration flame atomic absorption spectrometry (FAAS) system for trace element determination was developed based on sorption of soluble metal complexes on the walls of a PTFE knotted reactor using flow injection techniques. The system was applied to the determination of cadmium in biological materials. Cadmium complexed with sodium diethyldithiocarbamate was sorbed on the inner walls of the reactor and eluted on-line by isobutyl methyl ketone. The retention efficiency was 81% at a sampling loading rate of 5.2 ml/min. The enhancement factor was 66 and the concentration efficiency was 61/min with a 50 sec preconcentration period, consuming 4.2 ml sample. A detection limit of 0.1 μg/l. Cd (3σ) was obtained with a sampling frequency of 55/hr. The precisions were 1.2% RSD for 20 μg/l. Cd (N = 11). Thiourea and ascorbic acid/phenanthroline were used to overcome interferences from copper and iron, respectively. The analytical results obtained for powdered rice and human hair standard reference materials were in good agreement with the certified values.     

微量进样火焰原子吸收光谱法对牛奶中钙的直接测定

采用微量进样火焰原子吸收光谱法（FAAS）直接测定牛奶中的钙,无需样品预处理。该法与消化后常规FAAS法的测定结果一致。钙质量浓度在0～20 mg/L范围内与吸光度呈线性关系,检出限（S/N=3）为0.013 mg/L,加标回收率为98%～101%,相对标准偏差（n=6）小于2%。方法应用于实际样品的测定,结果令人满意。     

Ultra-trace determination of Pb(II) and Cd(II) in drinking water and alcoholic beverages using homogeneous liquid-liquid extraction followed by flame atomic absorption spectrometry

The determination of Pb(II) and Cd(II) in different sample matrices, including drinking water, distilled spirits and fruit wine, was carried out by flame atomic absorption spectrometry (FAAS) after pre-concentration using homogeneous liquid-liquid extraction (HLLE). First, the HLLE method was optimised with lead diethyldithiocarbamate (Pb-DDTC) complex which was extracted with a perfluorooctanoate anion (PFOA^?) dissolved in lithium hydroxide under acidic conditions. The optimum extraction conditions, using 0.01 M DDTC, 0.05 M PFOA^?, 3 M HCl and 1 mL of 30 vol. % acetone, were obtained. The Pb-DDTC complex in the nitric acid digest of the samples (50–150 mL) was extracted quantitatively into a drop of 100 μL of sediment phase. The sediment phase dissolved in 1 vol. % HNO₃ with at least 3–5 mL of the final volume was then determined by FAAS, affording a pre-concentration factor of 10–50. Hence, the HLLE method afforded an increase in both sensitivity and selectivity for the metal determination by conventional FAAS, resulting in ultra-trace level detection of Pb(II) in all samples analysed (drinking water, 9.2–23 ng mL^?1; distilled spirits, 23–50 ng mL^?1; fruit wine, 24–53 ng mL^?1). In addition, the proposed method could successfully be applied to Cd(II) determination in these samples.     

A Novel Glass Fiber Coated with Sol–Gel Poly-Diphenylsiloxane Sorbent for the On-Line Determination of Toxic Metals Using Flow Injection Column Preconcentration Platform Coupled with Flame Atomic Absorption Spectrometry

A novel simple and sensitive, time-based flow injection solid phase extraction system was developed for the automated determination of metals at low concentration. The potential of the proposed scheme, coupled with flame atomic absorption spectrometry (FAAS), was demonstrated for trace lead and chromium(VI) determination in environmental water samples. The method, which was based on a new sorptive extraction system, consisted of a microcolumn packed with glass fiber coated with sol–gel poly (diphenylsiloxane) (sol–gel PDPS), which is presented here for the first time. The analytical procedure involves the on-line chelate complex formation of target species with ammonium pyrrolidine dithiocarbamate (APDC), retention onto the hydrophobic sol–gel sorbent coated surface of glass fibers, and finally elution with methyl isobutyl ketone prior to atomization. All main chemical and hydrodynamic factors, which affect the complex formation, retention, and elution of the metal, were optimized thoroughly. Furthermore, the tolerance to potential interfering ions appearing in environmental samples was also explored. Enhancement factors of 215 and 70, detection limits (3 s) of 1.1 μg·L⁻¹ and 1.2 μg·L⁻¹, and relative standard deviations (RSD) of 3.0% (at 20.0 μg·L⁻¹) and 3.2% (at 20.0 μg·L⁻¹) were obtained for lead and chromium(VI), respec tively, for 120 s preconcentration time. The trueness of the developed method was estimated by analyzing certified reference materials and spiked environmental water samples.     

Determination of traces of lead,cadmium and zinc in copper by an arc-nebulization and flame atomic absorption technique

Arc-nebulization (a thermal nebulization technique) is used to form an aerosol of cadmium, lead and zinc. An open arc chamber of simple operation and an ejector of high efficiency are described which are adaptable for use with any flame atomic absorption spectrometer. Limits of detection better by one or two orders of magnitude than those achieved by conventional flame a.a.s. methods were obtained viz., 43 ng Pb, 5 ng Cd, 7 ng Zn (equivalent to 0.7, 0.08 and 0.11 ppm, respectively, in copper). Calibration with matrix-free solutions was possible for lead and cadmium but not for zinc. The spectral interference of copper on absorbance at the most sensitive zinc line (213.856nm) and the efficiency of arc nebulization of cadmium are also discussed.     

Determination of Copper by Faas After Preconcentration with Lead-4-Methylpiperidinedithiocarbamate on Microcrystalline Naphthalene By Solid Phase Extraction

ABSTRACT

By using the Pb-4-methylpiperidinedithiocarbamate complex (Pb(4-MPDC)₂) on microcrystalline naphthalene in a column a method was developed for the preconcentration of copper in water samples prior to its determination by FAAS. In this method, copper in liquid phase quantitatively replaces lead on the Pb(4-MPDC)₂-naphthalene solid phase in the column, forming solid Cu(4-MPDC)₂ complex.

Afterwards, copper on Cu(4-MPDC)₂-naphthalene can be easily eluted by potassium cyanide into the aqueous phase, and the Cu is measured by FAAS. The optimum experimental parameters such as pH, flow rate, sample volume, Pb(4-MPDC)₂-naphthalene ratio, concentration of the potassium cyanide solution and effect of matrix ions for the preconcentration of copper were investigated. The obtained recovery was nearly 100 %, when the enrichment factor was 100 for standard solutions and spiked water samples. The proposed method has been employed for the determination of copper in various standard metal alloys and natural water samples.     

Micellar Enhanced Analytical Application of Bismuthiol-II for the Spectrophotometric Determination of Trace Copper in Nutritional Matrices

 A simple spectrophotometric method for the determination of copper is described herewith, based on the formation of colored species of Cu (II) with 5-mercapto-3-phenyl-1,3,4-thiadiazole-2-thione (Bismuthiol II) in the presence of a neutral surfactant, Triton X-114. The yellow colored complex of Cu (II)–Bismuthiol-II–Triton X-114 shows maximum absorbance at 395 nm in water. The detection limit of the method is 0.03 mg/l while the Beer’s law is obeyed up to 1.2 mg/l of the analyte in an aqueous medium. The validity of the method has been examined for the determination of copper in wines, food supplements and raisins. The results obtained were in good agreement with those obtained using flame atomic absorption spectrometry (FAAS). The method thus constitutes a handy alternative for the determination of copper (II) in nutritional samples. Received May 16, 2001; accepted December 10, 2001; published online June 24, 2002