Si离子注入和H等离子体处理对单晶Si中空腔生长的影响研究

室温下首先采用160keVHe离子注入单晶Si样品到剂量5×10¹⁶ions/cm²,部分样品再接受80keVSi离子辐照到较高的剂量5×10¹⁵ions/cm²或接受高密度H等离子体处理.应用透射电镜观测分析了800℃高温退火引起的空腔的形成形貌.结果表明,附加Si离子辐照或H等离子体处理会影响Si中空腔的生长.就Si离子附加辐照而言,由于辐照引入富余的间隙子型缺陷,因此,它会抑制空腔的生长,而高密度H等离子体处理则有助于空腔的生长.定性地讨论了实验结果.     

离子辐照产生的空位型缺陷对Si中B原子热扩散的影响

使用二次离子质谱仪分析了附加的空位型缺陷对单晶Si中注入B原子热扩散的影响. Si中B原子是通过30keV B离子室温注入而引入的, 注入剂量为2×10¹⁴cm^－2. Si中附加的空位型缺陷通过两种方式产生: 一是采用40或160keV He离子注入单晶Si到剂量5×10¹⁶cm^－2,并经800°C退火1h; 二是采用0.5MeV F或O离子辐照单晶Si到剂量5×10¹⁵cm^－2.结果显示, 不同方式产生的附加的空位型缺陷均能抑制注入的B原子在随后热激活退火中发生瞬间增强扩散效应, 并且抑制的效果依赖于离子的种类和离子的能量. 结合透射电子显微镜和卢瑟福背散射分析结果对以上抑制效应进行了定性的讨论.     

离子注入ZnO薄膜的拉曼光谱研究

室温下,用80 keV N⁺和400 keV Xe⁺离子注入ZnO薄膜,注入剂量分别为5.0×10¹⁴—1.0×10¹⁷/cm²和2.0×10¹⁴—5.0×10¹⁵/cm².利用拉曼散射技术对注入前后的ZnO薄膜进行光谱测量和分析,研究了样品的拉曼光谱随离子注入剂量的变化规律.实验结果发现,未进行离子注入的样品在99,435 cm<     

Ni离子注入多晶ZrO2的表面电性能和结构

对氧化钇(Y₂O₃)部分稳定氧化锆(ZrO₂)样品在室温下进行了Ni离子注入(140kev,5×10¹⁵-2×10¹⁷ios/cm²)和热退火处理.应用电学测量,Rutherford背散射技术(RBS),X射线光电子能谱(XPS)和喇曼光谱方法研究了Ni离子注入多晶ZrO₂的表面电性能,注入层结构及其热退火的影响。     

60keV质子辐照对TiNi记忆合金薄膜马氏体相变的影响

 利用磁控溅射的方法在氧化后的单晶Si基片上制备了TiNi形状记忆合金薄膜，利用示差扫描量热法和原位X射线衍射研究了薄膜的马氏体相变特征。通过60keV质子注入（辐照）薄膜样品研究了H+离子对合金薄膜马氏体相变特征的影响，结果表明氢离子注入后引起了马氏体相变开始Ms和结束点Mf以及逆马氏体相变开始As和结束温度Af的下降，而对R相变开始Rs和结束温度Rf影响不大。掠入射X射线衍射表明H+离子注入后有氢化物形成。H⁺离子注入形成的氢化物是引起相变点的变化的主要因素。     

Ti-2Al-2.5Zr合金He离子辐照效应研究

 在Ti-2Al-2.5Zr合金中注入能量为75 keV的He离子，注入剂量分别为5×10¹⁶cm^-2，1×10¹⁷ cm^-2。通过显微硬度测量和剖面电子显微观察，研究了He离子对Ti-2Al-2.5Zr合金力学性能和显微组织的影响。结果表明:样品的显微硬度随He离子注量的增加而升高，在温度为350和550 ℃的Ar气中退火后硬度有所下降。剖面电子显微观察发现有位错环和He气泡生成，退火后He气泡有长大、缺陷有回复的趋势。辐照产生的位错环是辐照后硬度升高的直接原因，其退火发生回复又引起硬度随退火温度的升高而降低。     

锆离子注入锆-4合金缺陷的慢正电子研究

采用慢正电子束多普勒展宽谱研究了Zr离子注入Zr-4合金产生的缺陷及其退火回复行为，发现经过大于离子注入剂量为1×10¹⁶cm^-2的样品所产生的缺陷在注入过程中已经回复，而对剂量为1×10¹⁵cm^-2样品做300℃退火处理，其缺陷基本回复，得出合金缺陷回复能较低的结论. 考虑到材料的缺陷含量越高，其抗腐蚀性能越差，在辐照环境下通过给材料保持一定温度，即可使其缺陷得到较好回复，从而提高材料的抗腐蚀性能.     

高能带电粒子库仑对数量子力学效应研究

 先进燃料D-3He聚变产生的高能带电粒子在本底等离子体中慢化时间的准确性直接影响到能量平衡和高能离子压强的计算结果。结果表明：高能带电粒子与本底等离子体的离子相互作用的库仑对数量子力学效应明显。应使用高能带电粒子库仑对数力学效应来研究聚变产生的高能端部粒子慢化过程;能量大于等于25Z²_iZ²_iA_i keV的高能粒子与本底等离子体中离子的相互作用库仑对数最好也使用量子截断。     

采用EPR谱和TEM对YSZ单晶辐照损伤的研究

 利用电子顺磁共振(EPR)谱和透射电子显微镜(TEM)研究了YSZ单晶的辐照效应。200 keV的Xe和400 keV的Cs离子注入［111］取向的YSZ单晶中,注量均为5×10¹⁶ cm^-2。EPR结果表明辐照产生了共振吸收位置g‖=1.989 和 g⊥=1.869、对称轴为［111］的六配位Zr³⁺顺磁缺陷。Cs辐照产生了比Xe 离子辐照多约150倍的六配位Zr³⁺顺磁缺陷。两种样品的剖面电子显微分析表明没有发现非晶化转变,但是Cs离子辐照的样品在损伤集中区域产生了密度较高的缺陷。因此,EPR谱和电子显微观察均说明在相同离位损伤(约160 dpa)的情况下,Cs离子辐照比Xe 离子辐照产生了更多的缺陷。造成这一现象的原因是Cs离子是化学活性的而Xe 离子却是惰性的。     

低能N+注入植物种子射程分布的模拟计算

伴随着离子束生物技术的广泛应用, 国内许多单位开展了低能离子注入植物种子的实验研究. 其中关于低能离子注入植物种子诱变的物理机理, 集中在离子注入的深度-浓度分布上. 一些单位直接使用纵向非静态(LSS)理论和TRIM程序来计算低能离子注入植物种子的深度-浓度分布, 却发现计算结果与实验测量结果相差甚远. 所以在对植物种子靶材料进行处理和对LSS理论进行修正的基础上, 在二维近似情况下, 用蒙特卡罗方法分别模拟计算了200keV V⁺和20keV Ti⁺注入花生和棉花种子的射程分布, 得到了与实验结果较符合的曲线. 在此模型基础上, 计算了同样初始条件和理论计算模型下无法从实验上测量的N⁺注入植物种子的射程分布, 初步地为低能N⁺注入植物种子射程分布提供了一种理论计算方法.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.