Redox initiator systems for emulsion polymerization of acrylates

The performance of different redox initiator couples to initiate the emulsion polymerization of butyl acrylate at low temperature (40–50 °C) was investigated in both batch and seeded semibatch polymerizations. Polymerizations were carried out mimicking industrial conditions, that is, technical grade monomer and no N₂ purging was used during the polymerizations. The redox systems used contained as oxidants persulfates or hydroperoxides and as reducing agents ascorbic acid, formaldehyde sulfoxilate (SFS), tetramethyl ethylene diamine (TMEDA), Bruggolit 6 and 7 (FF6 and FF7), and sodium metabisulfites. Batch experiments showed that for systems using persulfates, the ammonium persulfate (APS)/TMEDA system provided the lower induction period and higher conversion, whereas for the systems with hydroperoxide oxidants, tert‐butyl hydroperoxide (TBHP)/FF7, TBHP/SFS, and H₂O₂/FF7 were the best alternatives. When these selected systems were used in seeded semibatch experiments of BA with allyl methacrylate, it was found that to obtain similar kinetics and microstructure (gel content and crosslinking density) than in case of using a thermal initiator at 80 °C, the polymerization could be run at 40 °C if the reactor was purged with N₂. Alternatively, in absence of N₂ polymerization, temperature should be increased to 50 °C and initiator concentration increased. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2917–2927, 2009     

Bulk polymerization of p‐dioxanone using a cyclic tin alkoxide as initiator

Poly(p‐dioxanone) with an inherent viscosity of over 1 dL/g has been synthesized using the cyclic tin alkoxide 1‐di‐n‐butyl‐1‐stanna‐2,5‐dioxacyclopentane as initiator. Poly(p‐dioxanone) was synthesized in bulk and the results have been compared with polymerizations using tin (II) 2‐ethylhexanoate (Sn(Oct)₂) as catalyst. Sn(Oct)₂ has often been reported to be an effective catalyst for the synthesis of poly(p‐dioxanone), but here it is compared with an initiator which is less prone to catalyze transesterification reactions. The results demonstrate that the cyclic tin initiator is a promising alternative for the synthesis of poly(p‐dioxanone) with a high inherent viscosity. Poly(p‐dioxanone) is a polymer with mechanical properties and a degradation rate suitable for tissue engineering applications. Both the cyclic tin initiator and Sn(Oct)₂ gave, under some reaction conditions, inherent viscosities around 1 dL/g. The best polymer synthesized using the cyclic tin initiator had a strain‐at‐break of 515% and a stress‐at‐break of 43 MPa. The inherent viscosity of this polymer was 1.16 dL/g, while Sn(Oct)₂ resulted in a polymer with an inherent viscosity less than 0.4 dL/g under the same reaction conditions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5552–5558, 2007     

Dispersion polymerization using hydroxy‐functional macroazoinitiators as an inistab

Hydroxy‐functional macroazoinitiators with central azo unit have been synthesized by atom transfer radical polymerization of 2‐hydroxyethyl methacrylate or 2‐hydroxypropyl methacrylate in methanol. The mean degrees of polymerization of the polymer chains beside the azo group were fixed at 30 and 60. Proton nuclear magnetic resonance (¹H NMR) and gel permeation chromatography were used to characterize the macroazoinitiators in terms of their chemical structure, molecular weight, and polydispersity, respectively. Dispersion polymerizations of styrene using the hydroxy‐functional macroazoinitiators as an inistab (initiator + colloidal stabilizer) in 2‐propanol or 2‐propanol/water media resulted in submicrometer‐sized polystyrene latex particles with hydroxy‐functional polymer hair. Electron microscopies, Fourier transform infrared spectrometer, thin layer chromatography, and ¹H NMR were used to characterize the particles in terms of their morphologies, particle sizes, and their distributions and chemical compositions. The synthesized particles behaved as an effective particulate emulsifier for the stabilization of oil‐in‐water emulsions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Two modes of asymmetric polymerization of phenylacetylenes having an L‐amino alcohol residue and two hydroxy groups

Four novel chiral phenylacetylenes having an L ‐amino alcohol residue and two hydroxymethyl groups were synthesized and polymerized by an achiral catalyst ((nbd)Rh⁺[η⁶‐(C₆H₅)B^?(C₆H₅)₃]) or a chiral catalytic system ([Rh(nbd)Cl]₂/(S)‐ or (R)‐phenylethylamine ((S)‐ or (R)‐PEA)). The two resulting polymers having an L ‐valinol or L ‐phenylalaninol residue showed Cotton effects at wavelengths around 430 nm. This observation indicated that they had an excess of one‐handed helical backbones. Positive and negative Cotton effects were observed only for the polymers having an L ‐valinol residue produced by using (R)‐ and (S)‐PEA as a cocatalyst, respectively, although the monomer had the same chirality. Even when the achiral catalyst was used, the two resulting polymers having an L ‐valinol or L ‐phenylalaninol residue showed Cotton effects despite the long distance between the chiral groups and the main chain. We have found the first example of a new type of chiral monomer, that is, a chiral phenylacetylene monomer having an L ‐amino alcohol residue and two hydroxy groups that was suitable for both modes of asymmetric polymerization, that is, the helix‐sense‐selective polymerization ( HSSP ) with the chiral catalytic system and the asymmetric‐induced polymerization ( AIP ) with the achiral catalyst. The other two monomers having L ‐alaninol and L ‐tyrosinol were found to be unsuitable to neither HSSP nor AIP because of their polymers' low solubility. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Electrochemical polymerization of aniline in phosphoric acid

The electrochemical synthesis of common conductive polymers such as polyaniline in phosphoric acid is a little different from that in other acidic media such as sulfuric acid. Electropolymerization in phosphoric acid is difficult, and this electrolyte medium is not applicable for this purpose. However, it is possible to overcome this problem by the addition of a small amount of sulfuric acid. In this case, the electropolymerization process can be successfully performed when the phosphate ion is doped. For instance, polyaniline films electrodeposited from an electrolyte solution of phosphoric acid have good stabilities and useful morphologies. Interestingly, phosphate doping results in the formation of nanostructures, whereas the polymer surface is macroscopically smooth. In an appropriate ratio, a mixed electrolyte of H₃PO₄ and H₂SO₄ can be used for the electropolymerization of aniline; thus, H₂SO₄ acts as a required agent for successful polymer growth, and H₃PO₄ acts as a doping agent. In this case, a small amount of sulfate is incorporated into the polymer matrix, which does not participate in the electrochemical insertion/extraction process. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3304–3311, 2006     

Azobenzene‐based initiator for atom transfer radical polymerization of methyl methacrylate

2‐Bromopropionic acid 2‐(4‐phenylazophenyl)ethyl ester, 2‐bromopropionic acid 6‐(4‐phenylazophenoxy)hexyl ester (BPA₆), 2‐bromopropionic acid‐(4‐phenylazoanilide), and 2‐bromopropionic acid 4‐[4‐(2‐bromopropionyloxy)phenylazo]phenyl ester (BPPE) were used as initiators with monofunctional or difunctional azobenzene for the heterogeneous atom transfer radical polymerization of methyl methacrylate with a copper(I) chloride/N,N,N′,N″,N″‐pentamethyldiethylenetriamine catalytic system. The rates of polymerizations exhibited first‐order kinetics with respect to the monomer, and a linear increase in the number‐average molecular weight with increasing monomer conversion was observed for these initiation systems. The polydispersity indices of the polymer were relatively low (1.15–1.44) up to high conversions in all cases. The fastest rate of polymerization and the highest initiation efficiency were achieved with BPA₆, and this could be explained by the longer distance between the halogen and azobenzene groups and the better solubility of the BPA₆ initiator. The redshifting of the UV absorptions of the polymers only occurred for the BPPE‐initiated system. The intensity of the UV absorptions of the polymers were weaker than those of the corresponding initiators in chloroform and decreased with the increasing molecular weights of the polymers in all cases. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2358–2367, 2005     

Synthesis and polymerization of phenylacetylene having two carbazole units and properties of the formed polymer

Novel carbazole‐containing acetylene monomer, 1‐(3‐ethynyl‐9‐carbazoyl)?4‐(9‐carbazoyl)benzene 1 was synthesized, polymerized, and copolymerized with phenylacetylene ( PA ) using [(nbd)RhCl]₂‐Et₃N, Rh⁺(nbd)[η⁶‐C₆H₅B^–(C₆H₅)₃], and WCl₆‐Ph₄Sn as catalysts. Polymers with number‐average molecular weights ranging from 7800 to 33,200 were obtained in 60%–quantitative yields. The absorption band edge of poly( 1 ‐co‐ PA ) ( 1 :PA = 8:2) was positioned at a wavelength longer than those of 1 and polyvinylcarbazole. Poly( 1 ‐co‐ PA ) ( 1:PA = 8:2) emitted fluorescence with 60% quantum yield. Poly( 1 ‐co‐ PA ) ( 1:PA = 8:2) worked as a hole transport material of an OLED with tris(8‐hydroxyquinoline)aluminum (Alq3) as an emission material. © 2015 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 2015 , 53, 1245–1251     

Fabrication of novel conjugated polymer nanostructure: Porphyrins and fullerenes conjugately linked to the polyacetylene backbone as pendant groups

A new series of conjugated polyacetylenes with conjugately linked fullerene and porphyrin groups as pendant units were prepared by a copolymerization reaction catalyzed by chloronorbornadiene rhodium(I)dimer‐triethylamine ([Rh(nbd)Cl]₂‐NEt₃) in anhydrous CHCl₃. These polymers were characterized with UV–vis spectroscopy, fluorescence spectroscopy, and voltammetry. Scanning electron microscopy indicated that the morphology of the copolymers consisted of uniform nanorods with a diameter of about 100 nm and a length of about 300 nm. Thin films of the copolymers produced steady and prompt photocurrent at an irradiation of 20.0 mW cm^?2 of white light, which was higher than that of a mixture of poly[5‐(4‐Ethynyl‐phenyl)‐10,15,20‐tris(4‐carbomethoxyphenyl)porphyrin zinc] and C₆₀. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2851–2861, 2005     

Polymerization of optically active disubstituted acetylene monomers by Pd catalyst bearing bulky phosphine ligand

Chloro- and aryl-substituted acetylene monomers having an optically active group were polymerized by a Pd catalyst [(^tBu₃P)PdMeCl] bearing a bulky phosphine ligand, and by MoCl₅ for comparison. The corresponding disubstituted acetylene polymers with M_n's = 2000–19,500 and 6900–10,800 were obtained in 29–83% and 11–62% yields when the Pd and Mo catalysts were used, respectively. The formation of polyacetylenes, poly[(R)- 1p ], poly[(R)- 1m ], and poly[(S)- 2p ] were confirmed by SEC and the presence of a Raman scattering peak based on the alternating double bonds of the main chain. Pd-based poly[(R)- 1m ] exhibited CD signals around 350 nm assignable to a certain secondary structure, while Mo-based poly[(R)- 1m ] did not. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3011–3016     

Free‐radical polymerization of methyl methacrylate with a tetrafunctional peroxide initiator

This study examined the use of a new tetrafunctional peroxide initiator in the bulk free‐radical polymerization of methyl methacrylate. The objective was to investigate the effect of using a multifunctional initiator through an examination of the rates of polymerization and the polymer properties. The molecular weights and radii of gyration were obtained with a size exclusion chromatograph equipped with an online multi‐angle laser light scattering detector. The performance of the tetrafunctional initiator was compared to that of a monofunctional counterpart [tert‐butylperoxy 2‐ethylhexyl carbonate (TBEC)]. The results showed that the new tetrafunctional peroxide initiator produced a faster rate of polymerization than TBEC at an equivalent concentration but also generated a polymer of a lower molecular weight. This trend was the opposite of what was observed in a previous study with styrene. When TBEC was used at a concentration four times that of the new tetrafunctional peroxide initiator, both produced equal rates of polymerization and similar molecular weights. The degree of branching was also investigated with radius‐of‐gyration plots. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5647–5661, 2004     

Strontium‐based initiator system for ring‐opening polymerization of cyclic esters

An amino isopropoxyl strontium (Sr‐PO) initiator, which was prepared by the reaction of propylene oxide with liquid strontium ammoniate solution, was used to carry out the ring‐opening polymerization (ROP) of cyclic esters to obtain aliphatic polyesters, such as poly(ε‐caprolactone) (PCL) and poly(L ‐lactide) (PLLA). The Sr‐PO initiator demonstrated an effective initiating activity for the ROP of ε‐caprolactone (ε‐CL) and L‐lactide (LLA) under mild conditions and adjusted the molecular weight by the ratio of monomer to Sr‐PO initiator. Block copolymer PCL‐b‐PLLA was prepared by sequential polymerization of ε‐CL and LLA, which was demonstrated by ¹H NMR, ¹³C NMR, and gel permeation chromatography. The chemical structure of Sr‐PO initiator was confirmed by elemental analysis of Sr and N, ¹H NMR analysis of the end groups in ε‐CL oligomer, and Fourier transform infrared (FTIR) spectroscopy. The end groups of PCL were hydroxyl and isopropoxycarbonyl, and FTIR spectroscopy showed the coordination between Sr‐PO initiator and model monomer γ‐butyrolactone. These experimental facts indicated that the ROP of cyclic esters followed a coordination‐insertion mechanism, and cyclic esters exclusively inserted into the Sr–O bond. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1934–1941, 2003     

Comparative study on the enzymatic polymerization of N‐substituted aniline derivatives

A series of water‐soluble N‐substituted poly(alkylanilines) (PNAAs) have been enzymatically synthesized with a variety of groups, from methyl to n‐butyl, such as poly(N‐methylaniline), poly(N‐ethylaniline), poly(N‐butylaniline) and poly(N‐phenylethanolamine). The syntheses were made in the presence of poly(4‐sodium styrene sulfonate) (SPS) as a template and horseradish peroxidase (HRP) as a catalyst. The size and type of the groups have a great effect on the properties of the final polymers. UV‐vis spectroscopy and cyclic voltammetry measurements confirmed that for enzymatically synthesized PNAAs/SPS complexes, the electroactivity increased with the bulkiness of the substituents. These polymers have been studied in the doped and undoped states by FT‐IR and UV‐vis spectroscopy. Also these polymers show multiple and reversible optical transitions that can be ascribed to the formation of polaron and bipolaron states. Copyright © 2005 John Wiley & Sons, Ltd.     

Ketone-zinc chloride combination as an initiator of polymerization

Dihydrocivetone, a macrocyclic ketone, has been found to be a weak initiator of vinyl polymerization. Anhydrous zinc chloride strongly promotes this to form a novel initiating system. Monomers tried successfully are methyl methacrylate, acrylonitrile and α-methylstyrene. The characteristic feature of polymerization of α-methylstyrene differs greatly from those of other monomers and those have been discussed and compared.     

Atom transfer radical polymerization of vinyl monomers in the presence of tetraethylthiuram disulfide

In situ ATRPs of MMA, St in the presence of TD catalyzed by FeCl₃/PPh₃ and CuBr₂/bpy have been studied, respectively. The results showed that the initiator Et₂NCS₂X (X = Cl or Br) and catalyst FeCl₂ or CuBr were formed in situ from the initiating components and the polymerization exhibited living radical polymerization characteristics. In the case of St polymerization with TD/CuBr/bpy initiating system, an inverse ATRP was observed.     

Molecular weight and configurational stability of poly[(fluorophenyl)acetylene]s prepared with metathesis and insertion catalysts

Series of high‐cis and cis/trans poly[(fluorophenyl)acetylene]s (PFPhA) have been prepared by polymerization of (2‐fluorophenyl)acetylene, (3‐fluorophenyl)acetylene, and (4‐fluorophenyl)acetylene with catalysts: [Rh(1,5‐cyclooctadiene) OCH₃]₂ (high‐cis PFPhAs) and tungsten(VI) oxychloride/tetraphenyltin (cis/trans PFPhAs). The molecular weight and configurational stability under various conditions at room temperature were studied for both PFPhAs series by means of size exclusion chromatography, ¹H‐NMR, and UV‐vis techniques. All samples exhibited slow degradation when exposed to the atmosphere in the solid state; the rate of degradation was independent on the F‐position on the Ph ring. The rate of degradation increased up to three orders of magnitude in the tetrahydrofuran solution where it was higher for high‐cis polymers compared with their cis/trans counterparts. The degradation of high‐cis PFPhAs was accompanied by significant cis‐to‐trans isomerization in aerated tetrahydrofuran solution. Rate of degradation and isomerization exhibited the same dependence on the F‐position on the Ph ring. The hypothesis was postulated that the degradation of high‐cis PFPhAs in solution was accelerated by cis‐to‐trans isomerization due to which the content of unpaired electrons on the main chains is enhanced. In both high‐cis and cis/trans series of polymers the ortho‐substituted isomers exhibited an enhanced stability compared with meta‐ and para‐substituted isomers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4296–4309, 2010     

Preparation of macroporous functionalized polymer beads by a multistep polymerization and their application in zirconocene catalysts for ethylene polymerization

Macroporous functionalized polymer beads of poly(4‐vinylpyridine‐co‐1,4‐divinylbenzene) [P(VPy‐co‐DVB)] were prepared by a multistep polymerization, including a polystyrene (PS) shape template by emulsifier‐free emulsion polymerization, linear PS seeds by staged template suspension polymerization, and macroporous functionalized polymer beads of P(VPy‐co‐DVB) by multistep seeded polymerization. The polymer beads, having a cellular texture, were made of many small, spherical particles. The bead size was 10–50 μm, and the pore size was 0.1–1.5 μm. The polymer beads were used as supports for zirconocene catalysts in ethylene polymerization. They were very different from traditional polymer supports. The polymer beads could be exfoliated to yield many spherical particles dispersed in the resulting polyethylene particles during ethylene polymerization. The influence of the polymer beads on the catalytic behavior of the supported catalyst and morphology of the resulting polyethylene was investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 873–880, 2003     

Ring opening polymerization of epoxides with urea‐derivatives of 4‐aminopyridine as thermally latent anionic initiator

In this study, a series of urea‐derivatives of 4‐aminopyridine (4AP) were evaluated as thermally latent initiators for the anionic ring‐opening polymerization of diglycidyl ether of bisphenol A (DGEBA). The urea‐derivatives were synthesized by the reactions of 4AP with the corresponding iso(thio)cyanates (phenyl isocyanate, tert‐butyl isocyanate, methylene diphenyl diisocyanate, and phenyl isothiocyanate). The ability of the urea‐derivatives as latent initiators was investigated with differential scanning calorimetry (DSC): Upon heating formulations comprised of DGEBA and the urea‐derivatives in a heating rate at 10 °C/min, the resulting DSC profiles indicated exothermic peaks to confirm that DGEBA underwent the polymerization efficiently. The corresponding DSC‐peak top temperatures (T_{peak top}) was higher than that observed for the formulation comprised of DGEBA and pristine 4AP, to clarify that the urea are useful initiators with thermal latency. A possible mechanism for the initiation step involves the thermal dissociation of the urea into 4AP and the corresponding isocyanates. 4AP thus generated readily initiated the ring‐opening polymerization of epoxide. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2518–2522     

The calorimetric determination of the ceiling temperature for the chemical polymerization of pyrrole

The previously found strong dependence of the polymerization enthalpy on the reaction temperature has been rationalized. The temperature dependence is to be ascribed to the existence of a ‘ceiling temperature’ for the polymerization process of the pyrrole monomer. The determined ceiling temperature has beenT?350 K when FeCl₃ was used as the oxidizing agent in CH₃CN solution. The existence of a ceiling temperature together with its already determined exoenthalpic nature allows to classify the polymerization reaction as an exoentropic one. From the dependence of the yield of insoluble polymer on the reaction temperature, the trend of the relative mean numeral molecular massM _n for the different obtained polymers has been determined. Measurements of electrical conductivity on pressed pellets of the different polymers allowed to establish a correlation between theM _n value and the conductivities The dependence of the conductivity on the exposition time to the air allowed to do some essays on the aging behaviour of the obtained polypyrrole. By making some assumptions, an absolute calorimetric determination of the value ofM _n of polypyrrole was tempted together with that of the related poly-N-vinilpyrrole.     

Dithiadiazolium salts as initiators for the cationic ring-opening polymerization of tetrahydrofuran

Mono-, bis- and tris-(1,3,2,4-dithiadiazolium) salts [R-(CNSNS ⁺)_n]_n+[AsF^-₆]_n (R = aryl, n = 1, 2, 3) were found to initiate the cationic ring-opening polymerization of tetrahydrofuran (THF) at room temperature to give clear gels from which the pure polymer was precipitated. 1,3,2,4-Dithiadiazolium cations associated with the hard [AsF₆]^- anion thus constitute a new class of cationic polymerization initiators. The poly(THF) formed by initiation with 1,3,2,4-dithiadiazolium cation was characterized by gel permeation chromatography, infrared spectrophotometry, and ¹³C-NMR spectroscopy. Number-average molecular weights of 198 700 g mol^-1 (polydispersity 1.96) and 190 000 g mol^-1 (polydispersity 1.61) were obtained using [PhCNSNS ] [AsF₆] and [C₆H₃-1,3,5-(CNSNS )₃][AsF₆]₃, respectively, as initiators. The use of multifunctional dithiadiazolium salts as initiators suggests that they may be useful in the preparation of starburst and dendritic polymers. © 1992 John Wiley & Sons, Inc.