Synthesis and characterization of a fluorinated polyanhydride

A fluorinated aromatic polyanhydride ( B ) was synthesized from the melt condensation of mixed anhydrides of 4,4′‐(hexafluoroisopropylidene)bis benzoic acid. Although the mixed anhydride from acetic anhydride yielded only a mixture of oligomers (weight‐average molecular weight < 2000), higher weight‐average molecular weight materials in the range of 15,000–18,000 were obtained with trifluoroacetic anhydride. Polymer B was soluble in chloroform and tetrahydrofuran, had a relatively high glass‐transition temperature of 176 °C with no melting point detected to 310 °C, and showed excellent thermal stability (5% weight loss observed at 380 °C by thermogravimetric analysis). The hydrolytic degradation of the fluorinated polyanhydride in a 0.1 M phosphate buffer of pH 7.4 at 37 °C was initially zero‐order, with 35% degradation occurring in 10 days. Loss of film integrity following that led to accelerated degradation, and almost complete dissolution was observed by the 16th day. The stability of the fluorinated polyanhydride in the solid state and in the solvent tetrahydrofuran was also evaluated. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3027–3036, 2002     

Organosoluble and light‐colored fluorinated polyimides from 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl and aromatic dianhydrides

A novel fluorinated diamine monomer based on 4,4′‐biphenol was synthesized via a straightforward, high‐yielding two‐step procedure. 4,4′‐Biphenol was reacted with 2‐chloro‐5‐nitrobenzotrifluoride in the presence of potassium carbonate to yield the intermediate dinitro compound, which was subsequently reduced to afford the fluorinated diamine, 4,4′‐bis(4‐amino‐3‐trifluoromethylphenoxy)biphenyl. A series of organosoluble fluorinated polyimides were prepared from the diamine with various aromatic dianhydrides via a conventional two‐step thermal imidization method. All polyimides were soluble in strong dipolar solvents such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide. The polyimides showed excellent thermal and thermooxidative stability and good mechanical properties. No significant weight loss was observed below a temperature of 520 °C in nitrogen or in air, and the glass‐transition temperatures ranged from 247 to 313 °C. Low dielectric constants (2.57–3.65 at 10 kHz), low moisture absorption (0.1–0.7 wt %), and low color intensity were also observed. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 524–534, 2002; DOI 10.1002/pola.10113     

Soluble fluorinated polyimides derived from 1,4‐ (4′‐aminophenoxy)‐2‐(3′‐trifluoromethylphenyl)benzene and aromatic dianhydrides

New fluorinated aromatic polyimides were prepared from 1,4‐(4′‐aminophenoxy)‐2‐(3′‐trifluoromethylphenyl)benzene and aromatic dianhydrides via the polycondensation of one‐step high‐temperature and two‐step thermal or chemical imidization methods. Experimental results indicated that some of the polyimides were soluble both in strong dipolar solvents (N‐methyl‐2‐pyrrolidone or N,N‐dimethylacetamide) and in common organic solvents such as tetrahydrofuran, CHCl₃, and acetone. The polyimides showed exceptional thermal and thermooxidative stability and good mechanical properties. No weight loss was detected before a temperature of 520 °C in nitrogen, and the glass‐transition temperatures ranged from 208 to 251 °C. Low dielectric constants (2.55–2.71 at 1 MHz), low refractive indices, and low water absorption were also observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2404–2413, 2001     

Synthesis and characterization of novel fluorinated polyimides derived from 4,4′‐[2,2,2‐trifluoro‐1‐(3‐trifluoromethylphenyl)ethylidene]diphthalic anhydride and aromatic diamines

A novel fluorinated aromatic dianhydride, 4,4′‐[2,2,2‐trifluoro‐1‐(3‐trifluoromethyl‐phenyl)ethylidene]diphthalic anhydride (TFDA) was synthesized by coupling of 3′‐trifluoromethyl‐2,2,2‐trifluoroacetophenone with o‐xylene under the catalysis of trifluoromethanesulfonic acid, followed by oxidation of KMnO₄ and dehydration. A series of fluorinated aromatic polyimides derived from the novel fluorinated aromatic dianhydride TFDA with various aromatic diamines, such as p‐phenylenediamine (p‐PDA), 4,4′‐oxydianiline (ODA), 1,4‐bis(4‐aminophenoxy)benzene (p‐APB), 1,3‐bis(4‐amino‐phenoxy)benzene (m‐APB), 4‐(4‐aminophenoxy)‐3‐trifluoromethylphenylamine (3FODA) and 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene (6FAPB), were prepared by polycondensation procedure. All the fluorinated polyimides were soluble in many polar organic solvents such as NMP, DMAc, DMF, and m‐cresol, as well as some of low boiling point organic solvents such as CHCl₃, THF, and acetone. Homogeneous and stable polyimide solutions with solid content as high as 35–40 wt % could be achieved, which were prepared by strong and flexible polyimide films or coatings. The polymer films have good thermal stability with the glass transition temperature of 232–322 °C, the temperature at 5% weight loss of 500–530 °C in nitrogen, and have outstanding mechanical properties with the tensile strengths of 80.5–133.2 MPa as well as elongations at breakage of 7.1–12.6%. It was also found that the polyimide films derived from TFDA and fluorinated aromatic diamines possess low dielectric constants of 2.75–3.02, a low dissipation factor in the range of 1.27–4.50 × 10^?3, and low moisture absorptions <1.3%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4143–4152, 2004     

Synthesis and characterization of copolyperoxides of indene with styrene, α‐methylstyrene,and α‐phenylstyrene

The oxidative copolymerization of indene with styrene, α‐methylstyrene, and α‐phenylstyrene is investigated. Copolyperoxides of different compositions have been synthesized by the free‐radical‐initiated oxidative copolymerization of indene with vinyl monomers. The compositions of the copolyperoxides obtained from the ¹H and ¹³C NMR spectra have been used to determine the reactivity ratios of the monomers. The reactivity ratios indicate that indene forms an ideal copolyperoxide with styrene and α‐methylstyrene and alternating copolyperoxides with α‐phenylstyrene. Thermal degradation studies via differential scanning calorimetry and electron‐impact mass spectroscopy support the alternating peroxide units in the copolyperoxide chain. The activation energy for thermal degradation suggests that the degradation is dependent on the dissociation of the peroxide (? O? O? ) bonds in the backbone of the copolyperoxide chain. Their flexibility has been examined in terms of the glass‐transition temperature. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2004–2017, 2002     

Synthesis and characterization of fluorinated poly(amide imide)s derived from 1,4‐bis(2′‐trifluoromethyl‐4′‐trimellitimidophenoxy)benzene and aromatic diamines

A series of fluorinated poly(amide imide)s were prepared from 1,4‐bis(2′‐trifluoromethyl‐4′‐trimellitimidophenoxy)benzene and various aromatic diamines [3,3′,5,5′‐tetramethyl‐4,4′‐diaminediphenylmethane, α,α‐bis(4‐amino‐3,5‐dimethyl phenyl)‐3′‐trifluoromethylphenylmethane, 1,4‐bis(4′‐amino‐2′‐trifluoromethylphenoxy)benzene, 4‐(3′‐trifluoromethylphenyl)‐2,6‐bis(3′‐aminophenyl)pyridine, and 1,1‐bis(4′‐aminophenyl)‐1‐(3′‐trifluoromethylphenyl)‐2,2,2‐trifluoroethane]. The fluorinated poly(amide imide)s, prepared by a one‐step polycondensation procedure, had good solubility both in strong aprotic solvents, such as N‐methyl‐2‐pyrrolidinone, dimethylacetamide, dimethylformamide, dimethyl sulfoxide, and cyclopentanone, and in common organic solvents, such as tetrahydrofuran and m‐cresol. Strong and flexible polymer films with tensile strengths of 84–99 MPa and ultimate elongation values of 6–9% were prepared by the casting of polymer solutions onto glass substrates, followed by thermal baking. The poly(amide imide) films exhibited high thermal stability, with glass‐transition temperatures of 257–266 °C and initial thermal decomposition temperatures of greater than 540 °C. The polymer films also had good dielectric properties, with dielectric constants of 3.26–3.52 and dissipation factors of 3.0–7.7 × 10^?3, and acceptable electrical insulating properties. The balance of excellent solubility and thermal stability associated with good mechanical and electrical properties made the poly(amide imide)s potential candidates for practical applications in the microelectronics industry and other related fields. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1831–1840, 2003     

Atom transfer radical homo‐ and block copolymerization of methyl 1‐bicyclobutanecarboxylate

A non‐olefinic monomer, methyl 1‐bicyclobutanecarboxylate (MBC), was successfully polymerized by the controlled/“living” atom transfer radical polymerization (ATRP) technique, resulting in a well‐defined homopolymer, PMBC, with only cyclobutane ring units in the polymer chain. An AB block copolymer poly(methyl 1‐bicyclobutanecarboxylate)‐b‐polystyrene (PMBC‐b‐PS), having an all‐ring unit segment, was also synthesized with narrow polydispersity and designed number‐average molecular weight in addition to precise end groups. The ¹H NMR spectra, glass‐transition temperature, and thermal stability of PMBC, PMBC‐b‐PS, and PS‐b‐PMBC were investigated. The experimental results showed that the cyclobutane rings in the two block polymers improved their thermal stability. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1929–1936, 2002     

Block copolyesters of poly(pentamethylene p,p′‐bibenzoate) and poly(tetramethylene adipate)

Hydroxy‐terminated poly(pentamethylene p,p′‐bibenzoate) oligomers with different molecular weights were prepared. The poly(pentamethylene p,p′‐bibenzoate) oligomers showed rather high crystallinity, and some of them exhibited a monotropic smectic phase. Block copolyesters with hard segments of poly(pentamethylene p,p′‐bibenzoate) and soft segments of poly(tetramethylene adipate) were prepared by coupling the poly(pentamethylene p,p′‐bibenzoate) oligomer and a poly(tetramethylene adipate)glycol with methylene‐4,4′‐diphenylene diisocyanate in solution. The block copolyesters were characterized by IR, ¹H NMR, differential scanning calorimetry, a polarized microscope, and X‐ray diffraction. The thermal transitions of the block copolyesters were dependent on the composition and the molecular weight of the poly(pentamethylene p,p′‐bibenzoate) oligomer used. The hard segments in the block copolyesters showed no liquid crystallinity and exhibited rather low crystallinity or were even amorphous. The molecular weight of the poly(pentamethylene p,p′‐bibenzoate) oligomer used influences the glass‐transition temperature and crystalline properties of the soft segments in the block copolyesters significantly. The effect on the glass‐transition temperature of the soft segments is described as the difference in miscibility between the hard and soft segments. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2626–2636, 2002     

Synthesis and cationic photopolymerization of new fluorinated,polyfunctional propenyl ether oligomers

New fluorinated, polyfunctional propenyl ether functionalized resins were synthesized, and their behavior in cationic photopolymerization was investigated. The photopolymerization proceeded efficiently with a high double‐bond conversion (>90%), giving rise to UV‐cured coatings characterized by low glass‐transition temperatures (?33 °C ≤ glass‐transition temperature ≤ ?15 °C) and hydrophobic surface properties. A fluorinated additive was also employed as a reactive additive in the cationic photopolymerization of trimethylolpropane tripropenyl ether, increasing the double‐bond conversion, polymer network flexibility, thermal stability, and surface hydrophobicity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6943–6951, 2006     

Surface ordering in thin films of liquid‐crystalline polymers containing fluorinated and protonated segments: Neutron‐reflectometry study

Surface‐induced layering of fluorinated and protonated segments in thin films of a main‐chain liquid‐crystalline polymer, consisting of α‐methylstilbene, bridged by a fluorinated group was revealed by neutron reflectometry. The layering was driven by the difference in surface energy of the fluorinated and protonated segments and by the inherent ordering of the polymer. The lower‐surface‐energy fluorinated segments segregated to the air surface, and the protonated segments segregated to the SiO_x layer at the Si substrate. The ordering induced by the interface decayed into the film with a characteristic decay length of about 100 Å. The surface‐induced periodicity ranged from 15 to 20 Å, which is approximately equal to the molecular dimension of the repeating unit on the polymer backbone. The magnitude of segregation increased upon annealing in the liquid‐crystalline temperature range. The segregation was retained upon annealing above the bulk order–disorder transition temperature. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2817–2824, 2002     

Preparation of fluorinated methacrylate/clay nanocomposite via in‐situ polymerization: Characterization,structure, and properties

Novel fluorinated coating containing well‐dispersed silicate nanolayers is successfully produced via in‐situ free radical polymerization of 2,2,2‐trifluoroethyl methacrylate in the presence of vinylbenzyl‐functionalized montmorillonite with different loading. The organic modification of sodium montmorillonite is achieved through an ion exchange reaction with triphenylvinylbenzylphosphonium chloride as surfactant prepared before use by reaction with vinylbenyl chloride and phosphine. The following in‐situ polymerization in the presence of organomodified clay leads to fluorinated nanocomposites with of partially exfoliated and intercalated morphologies, as determined via XRD and TEM analysis. The nanoscale dispersion of clay layers is also evidenced by thermal analysis; a moderate decrease of the glass transition temperature about 2–8 °C compared to their virgin PMATRIF and an improvement of their thermal stability as evidenced by TGA. The wettability of the nanocomposite films is also studied by contact angle measurements with water. The incorporation of organomodified clays not only increases the hydrophobicity of the fluorinated polymers but also improves the surface properties of obtained nanocomposites. Compared the virgin homopolymer, the mechanical properties of the nanocomposites are reduced by addition of organomodifed clay at temperature from 30 to 60 °C, whereas this trend is gradually decreased at higher temperature. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 411–418     

Photoimageable polyimides derived from α,α‐(4‐amino‐3,5‐dimethylphenyl)phenylmethane and aromatic dianhydride

Soluble and inherent photoimageable polyimides with improved photopatterning features were prepared from α,α‐(4‐amino‐3,5‐dimethylphenyl)phenylmethane and 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride. The polyimides possessed good combined chemical and physical properties: thermal stability was observed, with an initial thermal decomposition temperature of 565 °C and a high glass‐transition temperature of 318 °C. Homogeneous polyimide solutions in common organic solvents with solid contents as high as 20 wt % were prepared. These solutions had a shelf life greater than 3 months. The polyimides had high electric insulating properties and low dielectric constants and dissipation factors. Fine patterns were processed by direct exposure of the polyimide coatings to UV i‐line, followed by development with an organic developer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3012–3020, 2002     

Polymerization of methyl methacrylate by 2‐pyrrolidinone and n‐dodecyl mercaptan

The bulk polymerization of methyl methacrylate initiated with 2‐pyrrolidinone and n‐dodecyl mercaptan (R‐SH) has been explored. This polymerization system showed “living” characteristics; for example, the molecular weight of the resulting polymers increased with reaction time by gel permeation chromatographic analysis. Also, the polymer was characterized by Fourier transform infrared spectroscopy, ¹H NMR, and ¹³C NMR techniques. The polymer end with the iniferter structures was found. By the initial‐rate method, the polymerization rate depended on [2‐pyrrolidinone]^1.0 and [R‐SH]⁰. Combining the structure analysis and the polymerization‐rate expression, a possible mechanism was proposed. n‐Dodecyl mercaptan served dual roles—as a catalyst at low conversion and as a chain‐transfer agent at high conversion. Finally, the thermal properties were studied, and the glass‐transition temperature and thermal‐degradation temperature were, respectively, 25 and 80–100 °C higher than that of the azobisisobutyronitrile system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3692–3702, 2002     

Synthesis and characterization of fluorinated telomers containing vinylidene fluoride and hexafluoropropene from 1,6‐diiodoperfluorohexane

The synthesis of original fluorinated (co)telomers containing vinylidene fluoride (VDF) or VDF and hexafluoropropene (HFP) was achieved by radical telomerizations and (co)telomerizations of VDF (or VDF and HFP) in the presence of 1, 6‐diiodoperfluorohexane via a semisuspension process. tert‐Butyl peroxypivalate (TBPPi) was used as an efficient thermal initiator. The numbers of VDF and VDF/HFP base units in the (co)telomers were determined by ¹⁹F and ¹H NMR spectroscopy. They ranged from 10 to 190 VDF base units. Fluorinated telomers of various molecular weights (1200–12,600 g/mol) were obtained by the alteration of the initial [1,6‐diiodoperfluorohexane]₀/[fluoroalkenes]₀ and [TBPPi]₀/[fluoroalkenes]₀ molar ratios. The thermal properties of these fluorinated (co)telomers, such as the glass‐transition temperature and melting temperature, were examined. As expected, these telomers exhibited good thermal stability. They were stable at least up to 350 °C. The compounds containing more than 30 VDF units were crystalline, whereas all those containing VDF‐co‐HFP were amorphous with elastomeric properties, whatever the number was of the fluorinated base units. The structures of I–(VDF)_n–R_F–(VDF)_m–I and I–(HFP)_x(VDF)_n–R_F–(VDF)_m(HFP)_y–I (co)telomers were obtained, and the defects of the VDF chain and the ? CH₂CF₂I and ? CF₂CH₂I functionalities were studied successfully (where R_F = C₆F₁₂). The functionality in the iodine atoms was modified: the higher the VDF content in the telomers, the lower the normal end functionality (? CH₂CF₂I) and the higher the reversed extremity (? CF₂CH₂I). In addition, the percentage of defects increased when the number of VDF units increased. The molecular weights and molecular weight distributions of different telomers and cotelomers were also studied. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1470–1485, 2006     

Significant glass‐transition‐temperature increase through hydrogen‐bonded copolymers

The role of hydrogen bonding in promoting intermolecular cohesion and higher glass‐transition temperatures of polymer is a subject of longstanding interest. A series of poly(vinylphenol‐co‐vinylpyrrolidone) copolymers were prepared by the free‐radical copolymerization of acetoxystyrene and vinylpyrrolidone; this was followed by the selective removal of the acetyl protective group, with corresponding and significant glass‐transition‐temperature increases after this procedure. The incorporation of acetoxystyrene into poly(vinylpyrrolidone) resulted in lower glass‐transition temperatures because of the reduced dipole interactions in its homopolymers. However, the deacetylation of acetoxystyrene to transform the poly(vinylphenol‐co‐vinylpyrrolidone) copolymer enhanced the higher glass‐transition temperature because of the strong hydrogen bonding in the copolymer chain. The thermal properties and hydrogen bonding of these two copolymers were investigated with differential scanning calorimetry and Fourier transform infrared spectroscopy, and good correlations between the thermal behaviors and IR results were observed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2313–2323, 2002     

Synthesis and properties of cross‐linkable high molecular weight fluorinated copolyimides

A series of novel high molecular weight fluorinated co‐polyimides (Co‐PIs) containing styryl side chain based on 1,3‐bis(2‐trifluoromethyl‐4‐aminophenoxy)‐5‐(2,3,4,5‐tetrafluorophenoxy)benzene (6FTFPB) were successfully synthesized. The weight‐average molecular weights (M_ws) and polydispersities of the co‐polyimides were in the range 8.93–10.81 × 10⁴ and 1.33–1.82, respectively. The co‐polyimide film showed excellent solubility in organic solvents, high tensile properties (tensile strength exceeded 91 MPa), excellent optical transparency (cutoff wavelength at 332–339 nm and light transparencies above 89% at a wavelength of 550 nm), and high thermal stability (5% thermal weight‐loss temperature up to 510 °C). The casting and spinning films could be cross‐linked by thermal curing. The cured films show better combination property (including excellent resistance to solvents) than that of co‐polyimides. For instance, the glass transition temperature of Co‐PI‐1 (the molar weight ratio of 6FTFPB was 30%) increased from 217 to 271 °C, the tensile strength enhanced from 94 to 96 MPa, the 5% thermal weight‐loss temperature improved from 514 to 525 °C. Moreover, after cured, Co‐PI‐1 film also has a coefficient of thermal expansion (CTE) value of 60.3 ppm °C^?1, low root mean square surface roughness (R_q) at 4.130 nm and low dielectric constant of 2.60. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 349–359     

Synthesis and properties of novel polyurethanes containing 3,4‐dioxybenzylidenecyanoacetate group as a nonlinear optical chromophore

Methyl 3,4‐di‐(2′‐hydroxyethoxy)benzylidenecyanoacetate ( 3 ) was prepared by hydrolysis of methyl 3,4‐di‐(2′‐vinyloxyethoxy)benzylidenecyanoacetate ( 2 ). Diol 3 was condensed with 2,4‐toluenediisocyanate, 3,3′‐dimethoxy‐4,4′‐biphenylenediisocyanate, and 1,6‐hexamethylenediisocyanate to yield polyurethanes 4 – 6 containing the nonlinear optical chromophore 3,4‐dioxybenzylidenecyanoacetate. The resulting polyurethanes 4 – 6 were soluble in common organic solvents such as acetone and dimethylformamide. Polymers 4 – 6 indicated thermal stability up to 300 °C in thermogravimetric thermograms with glass‐transition temperature values obtained from differential scanning calorimetric thermograms in the range of 78–102 °C. The second‐harmonic generation coefficients (d₃₃) of the poled polymer films were around 6.9 × 10^?9 esu. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1742–1748, 2002     

Synthesis and properties of fluorinated polyimides. 1. Derived from novel 4,4″‐bis(aminophenoxy)‐3,3″‐trifluoromethyl terphenyl

A new diamine monomer, 4,4″‐bis(aminophenoxy)‐3,3″‐trifluoromethyl terphenyl (ATFT) was synthesized that led to a number of novel fluorinated polyimides by solution as well as thermal imidization routes when reacted with different commercially available dianhydrides like pyromellatic dianhydride (PMDA), benzophenone tetracarboxylic acid dianhydride (BTDA), or 2,2‐bis(3,4‐dicarboxyphenyl) hexafluoropropane (6FDA). The polyimides ATFT/BTDA and ATFT/6FDA derived from both routes were soluble in several organic solvents such as N,N‐dimethylformamide, N,N‐dimethylacetamide, and dimethyl sulfoxide. The polyimide ATFT/PMDA was only soluble in N‐methylpyrollidone. The polyimide films had low water absorption of 0.3–0.7%, low dielectric constants of 2.72–3.3 at 1 Hz, refractive indices of 1.594–1.647 at 589.3 nm, and optical transparency >85%. These polyimides showed very high thermal stability with decomposition temperatures (5% weight loss) up to 532 °C in air and good isothermal stability; only 7% weight loss occurred at 400 °C after 7 h, and less than 0.6% weight loss was observed at 315 °C for 5 h. Transparent thin films of these polyimides exhibited tensile strengths up to 112 MPa, a modulus of elasticity up to 3.05 GPa, and elongation at break up to 21% depending on the repeating unit structure. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1016–1027, 2002     

Synthesis and properties of fluorinated polyimides from a new unsymmetrical diamine: 1,4‐(2′‐Trifluoromethyl‐4′,4′‐diaminodiphenoxy)benzene

A new aromatic, unsymmetrical ether diamine with a trifluoromethyl pendent group, 1,4‐(2′‐trifluoromethyl‐4′,4″‐diaminodiphenoxy)benzene, was successfully synthesized in three steps with hydroquinone as a starting material and polymerized with various aromatic tetracarboxylic acid dianhydrides, including 4,4′‐oxydiphthalic anhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, 2,2′‐bis(3,4‐dicarboxyphenyl)‐hexafluoropropane dianhydride, and pyromellitic dianhydride, via a conventional two‐step thermal or chemical imidization method to produce a series of fluorinated polyimides. The polyimides were characterized with solubility tests, viscosity measurements, IR, ¹H NMR, and ¹³C NMR spectroscopy, X‐ray diffraction studies, and thermogravimetric analysis. The polyimides had inherent viscosities of 0.56–0.77 dL/g and were easily dissolved in both polar, aprotic solvents and common, low‐boiling‐point solvents. The resulting strong and flexible polyimide films exhibited excellent thermal stability, with decomposition temperatures (at 5% weight loss) above 522 °C and glass‐transition temperatures in the range of 232–272 °C. Moreover, the polymer films showed outstanding mechanical properties, with tensile strengths of 74.5–121.7 MPa, elongations at break of 6–13%, and initial moduli of 1.46–1.95 GPa, and good dielectric properties, with low dielectric constants of 1.82–2.53 at 10 MHz. Wide‐angle X‐ray diffraction measurements revealed that these polyimides were predominantly amorphous. These outstanding combined features ensure that the polymers are desirable candidate materials for advanced microelectronic applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6836–6846, 2006     

Fibrillar structure of resorbable microblock copolymers based on 1,5‐dioxepan‐2‐one and ε‐caprolactone

The copolymerization of 1,5‐dioxepan‐2‐one (DXO) and ε‐caprolactone, initiated by a five‐membered cyclic tin alkoxide initiator, was performed in chloroform at 60 °C. Copolymers with different molar ratios of DXO (25, 40, and 60%) were synthesized and characterized. ¹³C NMR spectroscopy of the carbonyl region revealed the formation of copolymers with a blocklike structure. Differential scanning calorimetry measurements showed that all the copolymers had a single glass transition between ?57 and ?49 °C and a melting temperature in the range of 30.1–47.7 °C, both of which were correlated with the amount of DXO. An increase in the amount of DXO led to an increase in the glass‐transition temperature and to a decrease in the melting temperature. Dynamic mechanical thermal analysis measurements confirmed the results of the calorimetric analysis, showing a single sharp drop in the storage modulus in the temperature region corresponding to the glass transition. Tensile testing demonstrated good mechanical properties with a tensile strength of 27–39 MPa and an elongation at break of up to 1400%. The morphology of the copolymers was examined with polarized optical microscopy and atomic force microscopy; the films that crystallized from the melt showed a short fibrillar structure (with a length of 0.05–0.4 μm) in contrast to the untreated solution‐cast films. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2412–2423, 2003