PVP催化还原及稳定化纳米银的微波合成

在聚乙烯基吡咯烷酮(PVP)的存在下,微波辐射硝酸银水溶液,合成了纳米银/PVP复合物。UV-Vis和XRD结果证明了生成的纳米银具有面心立方结构,PVP中N原子对银离子具有催化还原作用。TEM结果表明纳米银粒径在10～25nm,且较均匀分散在聚合物基体中;XPS结果表明PVP与纳米银之间存在相互作用。     

聚合物存在下纳米银复合材料的制备与表征

以聚丙烯腈聚乙二醇嵌段共聚物PAN-b-PEG-b-PAN为稳定剂, 在超声辐照下成功地制备了分散性较好、尺寸均匀的纳米银颗粒. 用X射线衍射(XRD)、红外光谱(FTIR)、透射电镜(TEM)、紫外-可见吸收光谱(UV-Vis)和热分析(TGA)等对制备的纳米银复合材料进行了表征. 红外结果表明超声辐照并没有破坏聚合物的链结构. 聚合物的引入, 对纳米银颗粒起到了很好的分散保护作用. 用低浓度的硝酸银溶液, 得到粒径较小的纳米银颗粒; 随着硝酸银浓度增大, 纳米银颗粒粒径也增大. 而聚合物的浓度增大时, 所得银纳米颗粒粒径减小. 对银纳米颗粒的形成机理进行了讨论.     

超声引发无皂乳液聚合制备纳米银/PAAEM复合材料及其表征

在不使用气体保护及乳化剂的条件下,超声辐射引发无皂乳液聚合双原位合成纳米银/聚乙酰乙酸基甲基丙烯酸乙酯(PAAEM)复合材料。并通过XRD、FTIR、TEM、HRTEM、XPS和TG等分析方法对其进行表征。结果表明:纳米银粒子具有面心立方结构和球形或近球形形貌,且较均匀地分散在聚合物基体中;纳米银粒子与基体之间的相互作用是纳米银与基体中乙酰乙酸基的羰基氧原子配位所产生的;而且纳米银粒子对基体PAAEM的热学性能有很大影响。     

原位法制备纳米银修饰碳纳米管环氧导电复合材料

将碳纳米管(CNTs)和乙酸银同时引入到环氧树脂-咪唑固化体系中,在固化过程中原位热降解银-咪唑复合物生成纳米银修饰碳纳米管,差示扫描量热仪(DSC)表明改性碳纳米管对环氧固化有一定的促进作用.采用X-射线衍射(XRD)表征了乙酸银和咪唑配合物[Ag(2E4MZ)2]Ac的结构,并提出了原位降解生成纳米银的机理.XRD结果表明,单独的乙酸银-咪唑配合物热降解生成的纳米银粒径为21-24nm,而配合物在环氧基体中生成的纳米银粒径为11-13nm.添加80%(质量分数)片状微米银粉制备的纳米银/碳纳米管环氧导电复合材料其体积电阻率低达9×10-5Ω·cm.当纳米银和碳纳米管质量比为80:20时,复合材料导电性和剪切强度达到最佳;采用扫描电镜(SEM)表征了复合材料的形貌结构.     

琥珀酸二异辛酯磺酸钠微乳体系中纳米银的制备及其连续相的影响

在琥珀酸二异辛酯磺酸钠(AOT)为表面活性剂、环己烷为连续相形成的微乳体系中, 利用水合肼还原AgNO₃制备了分散性良好的纳米银. 利用紫外-可见(UV-Vis)光谱和透射电镜(TEM)对所得产物进行了表征, TEM显微图像表明形成粒子为球形结构, 平均粒径为5.10 nm, 标准偏差为2.84 nm. 分别利用正己烷、正庚烷、正辛烷、环己烷和十二烷等作连续介质, 研究了微乳液中连续相对纳米银形成的影响. 随着正烷烃碳链长度的增加, 微乳液中胶束之间的交换速率增大, 形成粒子的平均粒径逐渐减小. 十二烷形成的微乳体系制备的纳米银溶胶具有最宽的共振吸收峰, 所得的纳米银粒子平均粒径最小. 环己烷形成的微乳液中反胶束具有特殊的界面强度, 导致纳米银晶核的形成速率过低, 纳米银晶粒的生长不完全.     

以葡聚糖-乙二胺聚合物为载体制备纳米银

以葡聚糖-乙二胺聚合物为载体制备纳米银.首先合成葡聚糖-乙二胺聚合物,并用紫外光谱红外光谱对聚合物进行表征;该聚合物与硝酸银反应生成葡聚糖-乙二胺聚合物-银配合物,再通过化学还原或光化学还原法使配合物中的银离子转变成单质银纳米粒,以透射电子显微镜激光纳米测定仪对制备的纳米银进行测定.结果表明制备出了粒径为23.1nm的纳米单质银.以葡聚糖-乙二胺聚合物为载体制备纳米银的方法是可行的.     

光敏感三臂星形聚[甲基丙烯酸2-(二甲氨基)乙酯]的合成及其光敏性能研究

以香豆素为光敏感基元,通过多步反应制备了三臂ATRP引发剂C-Br3,然后以CuBr/PMDETA为催化体系、甲基丙烯酸2-(二甲氨基)乙酯(DMAEMA)为单体,ATRP聚合法制备了三臂星形聚合物C-(PDMAEMA)3.用傅里叶变换红外光谱仪(FTIR)、紫外-可见光分光光度计(UV-Vis)和核磁共振仪(1H-NMR)等对C-Br3及聚合物进行了结构表征.研究表明,该三臂星形聚合物可在水中直接形成胶束,且该聚合物可在365和254 nm交替紫外光照下发生可逆光二聚反应.纳米粒度跟踪显示,光照前其胶束粒径为(87.7±27.8)nm、呈高斯分布;而在365和254 nm光反应后,聚合物胶束粒径大小与分布仅发生微弱变化.这可能是因为在光二聚反应前后,聚合物的双亲结构变化微弱所致.     

聚丙烯酰胺及其衍生物催化还原及纳米银的微波合成

以过硫酸钾为引发剂,微波辐射,双原位合成了纳米银/聚丙烯酰胺(PAM),纳米银/聚2-丙烯酰胺基-2-甲基丙磺酸(PAMPS)的复合物。TEM和XRD的结果表明了两种体系中都有纳米银的生成但具有不同形貌结构;FTIR结果表明在两种体系中分别合成了聚丙烯酰胺和聚2-丙烯酰胺基-2-甲基丙磺酸;XPS结果表明了聚合物中的N元素和Ag元素之间有相互作用。     

农药丙溴磷分子印迹聚合物微球的制备与结合性能研究

采用分子印迹技术,以丙溴磷为模板分子,分别以α-甲基丙烯酸和丙烯酰胺为功能单体,在乙腈溶液中合成了2种对丙溴磷具有选择性结合能力的分子印迹聚合物.紫外光度法研究表明,模板分子丙溴磷与α-甲基丙烯酸之间的作用强于其与丙烯酰胺之间的作用;扫描电镜的研究则表明以α-甲基丙烯酸为功能单体合成的分子印迹聚合物呈微球形,粒径约为0.5 ～2 μm;利用平衡结合实验研究了不同功能单体制备的聚合物对模板分子的结合能力及其对底物的选择性,经Scatchard模型分析,求出了聚合物的最大表观结合量(Qmax)和平衡离解常数(Kd)分别为49.44 μmol/g 和1.05 mmol/L.研究表明以α-甲基丙烯酸为功能单体合成的分子印迹聚合物对丙溴磷表现出更强的结合能力和更高的选择性.     

可控纳米银胶体的稳定性研究

纳米银胶体(AgNPs)长期储存不稳定性问题是本研究的中心,着重考察了不同前驱体对纳米银胶体的稳定性影响.分别以银氨([Ag(NH₃)₂]OH)溶液和AgNO₃溶液为前驱体制备了多份纳米银胶体样品并通过UV-Vis、FE-SEM、EDS、ZETA电位仪等现代分析测试手段研究了纳米银胶的形貌、粒径大小以及稳定性.对比分析发现,以[Ag(NH₃)₂]OH溶液为前驱体,制备的纳米银胶体具有粒径可控,尺寸均一,分散性良好等特点;而且经过一个月的常温储存,表现出比用AgNO₃溶液为前驱体制备的纳米银胶体具有更高的储存稳定性.     

MMA/MAh共聚物的合成及其凝胶聚合物电解质性能

从聚甲基丙烯酸甲酯型凝胶聚合物电解质存在的问题出发,设计制备一种甲基丙烯酸甲酯/共聚马来酸酐型凝胶聚合物电解质.采用溶液聚合法,以偶氮二异丁腈(AIBN)为引发剂,甲基丙烯酸甲酯(MMA)、顺丁烯二酸酐(MAh)为单体,其MMA与MAh单体摩尔配比为1∶1,合成了P(MMA-co-MAh)共聚物;采用凝胶色谱(GPC)、傅立叶红外光谱(FTIR)、核磁共振(MNR)、示差扫描量热法(DSC)、热失重分析(TGA)、X-射线衍射分析(XRD)对所合成共聚物的结构进行了表征.结果表明,合成的共聚物为无规非晶型聚合物,其数均分子量Mn为6.40×104,共聚物中MMA与MAh链段摩尔比大约为8∶1,热分解温度为300℃,玻璃化转变温度(Tg)为121.3℃.以P(MMA-co-MAh)共聚物为树脂基体,环状碳酸1,2-丙二酯(PC)为增塑剂,LiClO4为电解质盐,制备了凝胶聚合物电解质(GPE),当共聚物含量为45 wt%时,GPE具有好的成膜性,其室温离子电导率为3.0×10-5S/cm.     

竹木质素的红外光谱与X射线光电子能谱分析

应用傅里叶转换红外光谱(FTIR)和X射线光电子能谱(XPS), 研究了3种提纯方法得到的竹木质素及其化学反应产物的化学结构特性. 确定竹木质素C_1s的电子结合能分别为283.52 (C—H或C—C), 284.58～285.72 (C—OR或C—OH), 286.10～286.44 (C＝O或HO—C—OR), 287.65～287.72 (O—C＝O) eV. O_1s的电子结合能分别为530.31(羟基氧原子), 531.45～531.72(醛或酮的羰基氧原子), 532.73～533.74(酯键或羧酸中的羰基氧原子) eV. 竹木质素中的结构单元之间主要是通过醚键和碳碳单键连接, 慈竹磨木木质素结构单元中醚键、碳碳单键、酯键、羰基和烯双键的比例为100∶63∶32∶40∶32 (49.3∶31.0∶16.0∶19.9∶16.0)     

梳状P(MMA-co-MAh)-g-PEGME共聚物的合成及结构与性能

用自制的甲基丙烯酸甲酯和马来酸酐的共聚物P(MMA-co-MAh)为反应物,聚乙二醇单甲醚(PEGME)为接枝单体,合成了梳状P(MMA-co-MAh)共聚物多缩乙二醇酯(P(MMA-co-MAh)-g-MPEG).采用傅立叶红外光谱(FTIR)、核磁共振(NMR)13C谱、1H谱以及H,C-COSP谱对所合成的梳状共聚物结构进行表征;热失重分析(TGA)和示差扫描量热法(DSC)对所合成的共聚物的物理性能进行了分析.FTIR及NMR结果表明,聚乙二醇单甲醚通过酯化反应接枝到P(MMA-co-MAh)共聚物上,形成以MMA/MAh共聚物为主链,聚乙二醇单甲醚为侧链的梳状共聚物,其在马来酸酐上的接枝率大约为20%;热性能分析结果表明,合成的梳状共聚物热分解温度与共聚物P(MMA-co-MAh)的分解温度相差不大,接枝后的梳状共聚物也具有高的热稳定性,起始热分解温度在325.9℃左右,且该梳状共聚物具有两个玻璃化转变温度,一个是由于侧链的玻璃化转变引起的,温度为32℃左右;一个是主链的玻璃化转变引起的,温度为120℃左右.在主链玻璃化转变温度以下,侧链是可以移动的,有利于电活性物质和离子等在聚合物基体中的扩散和迁移.     

STUDY ON THE PREPARATION AND PERFORMANCES OF P(VAc-MMA) POLYMER ELECTROLYTES FOR LITHIUM ION BATTERY

A random copolymer P(VAc-MMA)was synthesized via seeded emulsion copolymerization with vinyl acetate (VAc)and methyl methacrylate(MMA)as monomers,and the polymer electrolytes comprising blend of corresponding copolymer P(VAc-MMA)as a host polymer and LiClO_4 as a dopant were prepared by solution casting technique. Performances of the synthesized copolymer and prepared polymer membrane and electrolyte were studied by FTIR,XRD, TG,DSC,mechanical testing and AC impedance.According to the study of FTIR and D...     

Quantitative Determination of Iron Carbonyls on Polymer Supports

With the aid of FTIR analysis, the absolute amount of iron carbonyl complexes attached to a DVB/styrene copolymer backbone and the ratio of the biscoordination product to the monocoordination product were determined. These determinations were based upon the relative IR peak absorption areas at 2040 cm^?1, 1880 cm^?1, and 2915 cm^?1 for the C=O stretching of monocoordination product, biscoordination product, and the C—H stretching of polymer backbone, respectively.     

An acceptor‐acceptor conjugated copolymer based on perylene diimide for high mobility n‐channel transistor in air

A new solution‐processable acceptor‐acceptor conjugated copolymer ( P1 ) based on perylene diimide (PDI) incorporating planar electron‐deficient fluorenone was synthesized by palladium(0)‐catalyzed Suzuki coupling reaction. Relative to the donor‐acceptor conjugated copolymer ( P2 ) of PDI and dithienothiophene, polymer P1 exhibits 0.1 eV down shift of lowest unoccupied molecular orbital (LUMO) level, 70 nm blue shift of low‐energy absorption band, and 0.36 eV increase of optical band gap. Polymer P1 in top‐contact bottom‐gate organic field‐effect transistors exhibits a saturation electron mobility of 0.01 cm²/(V s) in air, while P2 does not function in the same device in air. The better air stability of P1 is attributed to a more dense packing of the polymer chains excluding oxygen or water and lower LUMO level of P1 . © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation and clinical application of immunomagnetic latex

Magnetic poly(methyl methacrylate) (PMMA)/poly(methyl methacrylate‐co‐methacrylic acid) [P(MMA–MAA)] composite polymer latices were synthesized by two‐stage soapless emulsion polymerization in the presence of magnetite (Fe₃O₄) ferrofluids. Different types and concentrations of fatty acids were reacted with the Fe₃O₄ particles, which were prepared by the coprecipitation of Fe(II) and Fe(III) salts to obtain stable Fe₃O₄ ferrofluids. The Fe₃O₄/polymer particles were monodisperse, and the composite polymer particle size was approximately 100 nm. The morphology of the magnetic composite polymer latex particles was a core–shell structure. The core was PMMA encapsulating Fe₃O₄ particles, and the shell was the P(MMA–MAA) copolymer. The carboxylic acid functional groups (COOH) of methacrylic acid (MAA) were mostly distributed on the surface of the composite polymer latex particles. Antibodies (anti‐human immunoglobulin G) were then chemically bound with COOH groups onto the surface of the magnetic core–shell composite latices through the medium of carbodiimide to form the antibody‐coated magnetic latices (magnetic immunolatices). The MAA shell composition of the composite latex could be adjusted to control the number of COOH groups and thus the number of antibody molecules on the magnetic composite latex particles. With a magnetic sorting device, the magnetic immunolatices derived from the magnetic PMMA/P(MMA–MAA) core–shell composite polymer latex performed well in cell‐separation experiments based on the antigen–antibody reaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1342–1356, 2005     

Structure induced by irradiation of femtosecond laser pulse in dyed polymeric materials

We investigated the structures induced by an irradiation of a near‐infrared (NIR) femtosecond laser pulse in dye‐doped polymeric materials {poly(methyl methacrylate) (PMMA), thermoplastic epoxy resin (Epoxy), and a block copolymer of methyl methacrylate and ethyl acrylate‐butyl acrylate [p(MMA/EA‐BA) block copolymer]}. Dyes used were classified into two types—type 1 with absorption at 400 nm and type 2 with no absorption at 400 nm. The 400‐nm wavelength corresponds to the two‐photon absorption region by the irradiated NIR laser pulse at 800 nm. Type 1 dye‐doped PMMA and p(MMA/EA‐BA) block copolymer showed a peculiar dye additive effect for the structures induced by the line irradiation of a NIR femtosecond laser pulse. On the contrary, dye‐doped Epoxy did not exhibit a dye additive effect. The different results among PMMA, p(MMA/EA‐BA) block copolymer, and Epoxy matrix polymers are supposed to be related to the difference of electron‐acceptor properties. The mechanism of this type 1 dye‐additive‐effect phenomenon for PMMA and p(MMA/EA‐BA) block copolymer is discussed on the basis of two‐photon absorption of type 1 dye at 400 nm by the irradiation of a femtosecond laser pulse with 800 nm wavelength and the dissipation of the absorbed energy to the polymer matrix among various transition processes. Dyes with a low‐fluorescence quantum yield favored the formation of thicker grating structures. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2800–2806, 2002     

含氮杂冠醚双亲聚合物纳米球的制备及性能

设计、合成了含氮杂冠醚和腺嘌呤的双亲聚合物,聚[N,N-二乙氧基-1,10-二氮杂-18冠-6-5-甲基-腺嘌呤-异酞酸酯](PCASE).SEM观测到在水溶液中该聚合物与5-氟尿嘧啶(5-flu)小分子识别后自发聚集成直径约140～210nm的纳米球,用动态光散射测得水溶液中PCASE/5-flu纳米球的粒径主要集中在120～230nm范围内,FTIR研究了PCASE/5-flu纳米球内聚合物PCASE中腺嘌呤与底物5-氟尿嘧啶的分子识别,结果表明,识别后5-氟尿嘧啶环上C(2)=O伸缩振动峰从1724cm-1位移至1718cm-1,且聚合物中腺嘌呤NH2峰3324cm-1消失,出现了一个新的NH2峰3432cm-1,说明5-氟尿嘧啶环上C(2)=O与聚合物PCASE中腺嘌呤上NH2间形成了氢键.变温红外谱显示,识别后的羰基峰1718cm-1随温度的升高逐渐向高波数回移,并最终稳定在5-氟尿嘧啶环上C(2)=O识别前的1724cm-1处,且识别后产生的新NH2峰3432cm-1随温度的升高逐渐减弱至消失,表明所形成的氢键断裂.