The Effect of Flower-Like Magnesium Hydroxide Nanostructure on the Thermal Stability of Cellulose Acetate and Acrylonitrile–Butadiene–Styrene

Flower-like magnesium hydroxide (Mg(OH)₂) nanostructures were synthesized via a simple hydrothermal reaction at relatively low temperature. The Mg(OH)₂ nanostructures were then added to acrylonitrile–butadiene–styrene (ABS) and cellulose acetate (CA) polymers. The effect of Mg(OH)₂ nanostructures on the thermal stability of the polymeric matrixes has been investigated. The thermal decomposition of the nanocomposites shifts towards higher temperature in the presence of the Mg(OH)₂. The enhancement of thermal stability of nanocomposites is due to endothermically decomposition of magnesium hydroxide that releases of water and dilutes combustible gases. Nanostructures and nanocomposites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA), differential thermal analysis (DTA), UL-94 test and limiting oxygen index (LOI) analysis.     

Fabrication of Low-Dimension CdSe Structures by Atomic Layer Epitaxy

Formation of thin cadmium selenide films on semiconductor and dielectric matrixes of (100) and (111) orientation from atomic-molecular beams was considered. Temperature ranges in which thin CdSe films are formed were determined. Conditions for layer-by-layer growth of nanostructures were established.     

The influence of the ratio between the selenium: Polyvinylpyrrolidone complex components on the formation and morphological characteristics of nanostructures

Optical and spectral methods were used to study nanostructures formed in the reduction of ionic selenium in the selenite-ascorbate redox system in aqueous solutions of polyvinylpyrrolidone, a physiologically active polymer. The weight ratio between the selenium: polymer complex components (ν) was varied over a wide range (ν = 0.01?0.2). The adsorption of a substantial number of macromolecules (up to 1000 at ν = 0.1?0.2) on selenium nanoparticles was observed experimentally. This resulted in the formation of supramolecular spherical nanostructures with a high polymeric shell density. The Gibbs energies of macromolecule-Se⁰ nanoparticle interactions were calculated for polymeric nanostructures in the region of the formation of stable dispersions. The flow birefringence, dynamic light scattering, and spectrophotometry methods were used to determine the region of saturation of the adsorption capacity of selenium nanoparticles in selenium-containing nanocomposites (ν = 0.1?0.2).     

The influence of the nature of a nanoparticle and polymer matrix on the morphological characteristics of polymeric nanostructures

Comparative studies of the morphological characteristics of selenium- and platinum-containing nanostructures were performed by molecular optics methods. The nanostructures were based on an ionogenic polymeric stabilizer, poly-N,N,N,N-trimethylmethacryloyloxyethylammonium methyl sulfate, and a non-ionogenic polymeric stabilizer, oxyethylcellulose. Studies were performed in aqueous solutions at a fixed ratio between components. The adsorption of a considerable number of polymer macromolecules on nanoparticles with the formation of superhigh-molecular-weight nanostructures with shapes close to spherical was observed for all the nanosystems studied. The thermodynamic state of nanosystems was characterized. Certain morphological characteristics of nanostructures were substantially influenced by the nature of both nanoparticles and polymer matrix.     

Morphology-controlled fabrication of polygonal ZnO nanobowls templated from spherical polymeric nanowell arrays

We report a facile and effective strategy for synthesizing morphology-controlled patterned ZnO nanostructures. Polymeric nanowell arrays were employed as scaffold templates, followed by solution dipping and calcination process, polygonal ZnO nanobowl structures were fabricated on silicon substrate. The ordered polymeric nanowell arrays not only provided confined areas for depositing desired materials, but also induced shape transition of ZnO nanobowls from circular to polygonal. The morphology of the patterned ZnO nanostructures can be easily controlled by tuning parameters of polymeric nanowell arrays and other treatment conditions. The patterned structures were characterized by field emission scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD) and thermogravimetric analysis (TGA).     

Ion-selective potentiometric sensors with silicone sensing membranes: A review

Ion-selective electrodes (ISEs) are used widely in mainframe analyzers for clinical chemistry, but there is also an increasing interest in the development of paper-based devices, wearable and implantable sensors, and other miniaturized ISEs. This trend is spurring much research in developing solid contact materials that enable miniaturization. The development of suitable polymeric matrixes for such sensors has only received less attention. In particular, in spite of lifetime limitations and toxicity concerns, polymeric matrixes comprising plasticizers are still commonly used. To that end, we note the benefits of silicone materials as alternative polymeric matrixes and, in particular, their promise for enhanced biocompatibility. While there has been steady progress in the development of ISEs with silicone membranes, this topic has not been reviewed for many years. This review critically discusses key fundamental characteristics of ISEs with silicone sensing and reference membranes, including their biocompatibility, adhesion to device substrates, water uptake, polarity, common impurities, and commercial availabilities. This is followed by a discussion of specific types of silicones and their use in ISEs, with the goal to inform and stimulate future research efforts into such devices.     

Interfacially formed organized planar inorganic, polymeric and composite nanostructures

This paper discusses synthetic strategies for fabrication of new organized planar inorganic, polymeric, composite and bio-inorganic nanostructures by methods based on chemical reactions and physical interactions at the gas-liquid interface, Langmuir monolayer technique, interfacial ligand exchange and substitution reactions, self-assembling and self-organization processes, DNA templating and scaffolding. Stable reproducible planar assemblies of ligand-stabilized molecular nanoclusters containing definite number of atoms have been formed on solid substrate surfaces via preparation and deposition of mixed Langmuir monolayers composed by nanocluster and surfactant molecules. A novel approach to synthesis of inorganic nanoparticles and to formation of self-organized planar inorganic nanostructures has been introduced. In that approach, nanoparticles and nanostructures are fabricated via decomposition of insoluble metal-organic precursor compounds in a layer at the gas-liquid interface. The ultimately thin and anisotropic dynamic monomolecular reaction system was realized in that approach with quasi-two-dimensional growth and organization of nanoparticles and nanostructures in the plain of Langmuir monolayer. Photochemical and redox reactions were used to initiate processes of interfacial nucleation and growth of inorganic phase. It has been demonstrated that morphology of resulting inorganic nanostructures can be controlled efficiently by variations of growth conditions via changes in state and composition of interfacial planar reaction media, and by variations of composition of adjacent bulk phases. Planar arrays and chains of iron oxide and ultrasmall noble metal (Au and Pd) nanoparticles, nanowires and new organized planar disk, ring, net-like, labyrinth and very high-surface area nanostructures were obtained by methods based on that approach. Highly organized monomolecular polymeric films on solid substrates were obtained via deposition of Langmuir monolayer formed by water-insoluble amphiphilic polycation molecules. Corresponding nanoscale-ordered planar polymeric nanocomposite films with incorporated ligand-stabilized molecular metallic nanoclusters and interfacially grown nanoparticles were fabricated successfully. Novel planar DNA complexes with amphiphilic polycation monolayer were formed at the gas-aqueous phase interface and then deposited on solid substrates. Toroidal and new net-like conformations were discovered in those complexes. Nanoscale supramolecular organization of the complexes was dependent on cationic amphiphile monolayer state during the DNA binding. These monolayer and multilayer DNA/amphiphilic polycation complex Langmuir-Blodgett films were used as templates and nanoreactors for generation of inorganic nanostructures via metal cation binding with DNA and following inorganic phase growth reactions. As a result, ultrathin polymeric nanocomposite films with integrated DNA building blocks and organized inorganic semiconductor (CdS) and iron oxide quasi-linear nanostructures were formed. It has been demonstrated that interaction of deposited planar DNA/amphiphilic polycation complexes with bulk phase colloid inorganic cationic ligands (CdSe nano-rods) can result in formation of new highly organized hybrid bio-inorganic nanostructures via interfacial ligand exchange and self-organization processes. The methods developed can be useful for investigation of fundamental mechanisms of nanoscale structural organization and transformation processes in various inorganic and molecular systems including bio-molecular and bio-inorganic nanostructures. Also, those methods are relatively simple, environmentally safe and thus could prove to be efficient practical instruments of molecular nanotechnology with potential of design and cost-effective fabrication of new controlled-morphology organized planar inorganic and composite nanostructured materials. Possible applications of obtained nanostructures and future developments are also discussed.     

Amphiphilic gradient copolymers of 2‐methyl‐ and 2‐phenyl‐2‐oxazoline: self‐organization in aqueous media and drug encapsulation

Gradient (or pseudo‐diblock) copolymers were synthesized from 2‐methyl‐2‐oxazoline and 2‐phenyl‐2‐oxazoline monomer mixtures via cationic polymerization. The self‐assembling properties of these biocompatible gradient copolymers in aqueous solutions were investigated, in an effort to use the produced nanostructures as nanocarriers for hydrophobic pharmaceutical molecules. Dynamic and static light scattering as well as AFM measurements showed that the copolymers assemble in different supramolecular nanostructures (spherical micelles, vesicles and aggregates) depending on copolymer composition. Fluorescence spectroscopy studies revealed a microenvironment of unusually high polarity inside the nanostructures. This observation is related partly to the gradient structure of the copolymers. The polymeric nanostructures were stable with time. Their structural properties in different aqueous media—PBS buffer, RPMI solution—simulating conditions used in pharmacological/medicinal studies, have been also investigated and a composition dependent behavior was observed. Finally, the hydrophobic drug indomethacin was successfully encapsulated within the gradient copolymer nanostructures and the properties of the mixed aggregates were studied in respect to the initial copolymer assemblies. The produced aggregates encapsulating indomethacin showed a significant increase of their mass and size compared to original purely polymeric ones. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Self-organization and morphological characteristics of selenium-containing nanostructures based on rigid-chain polymers

Macroinitiators containing β-diketonate fragments were prepared by copolymerization of styrene with cobalt(II) 5-Formation and morphological characteristics of selenium-containing nanostructures formed by reduction of selenious acid with ascorbic acid in the presence of ionic or nonionic polymeric stabilizer in aqueous solutions were studied by methods of nonlinear optics and flow birefringence at widely varied selenium to polymer weight ratio in solution ν. The molecular weights, root-mean-square and hydrodynamic sizes, and mean density of the nanostructures were calculated, and the trends in variation of these quantities were compared.     

Alpha-cyclodextrin-induced self-assembly of a double-hydrophilic block copolymer in aqueous solution

Double-hydrophilic poly(ethylene oxide)-b-poly(acrylic acid) (PEO-b-PAA) self-assembled into nanostructures in basic solution upon the addition of alpha-cyclodextrin (alpha-CD) as a result of the complexation between alpha-CD and PEO. The nanostructures produced were spherical in shape as observed by transmission electron microscopy (TEM) and possessed radii that were much larger than that of a single stretched polymeric chain. The ratio of Rg/Rh (where Rg is the z-average radius of gyration and Rh is the hydrodynamic radius) obtained from laser light scattering (LLS) was approximately approximately 1.0, and the aggregation number was approximately 4100. The zeta-potential of complex particle was -45 mV, suggesting that the particle possessed a stable negatively charged surface, attributed to ionized PAA segments. The above results suggested that the nanostructures formed in the PEO-b-PAA/alpha-CD solution at high pH were likely to be spherical vesicles.     

Crystallization of silver chloride in crazed porous polymers

During this study the formation and growth of silver chloride crystals in crazed porous polymeric matrixes of poly(ethylene terephthalate) (PET) and polypropylene (PP) were under investigation. The rate of formation and dispersity and the way AgCl particles aggregate in porous polymers were shown to be dependent on the effective volume porosity, pore dimension, and physical state of the polymer. Methods of the determination of diffusion and distribution constants for low-molecular substances in porous polymers were suggested, and a mechanism of silver chloride crystallization in porous medium was proposed.     

Synthesis of polymeric core–shell particles using surface‐initiated living free‐radical polymerization

An easy and novel approach to the synthesis of functionalized nanostructured polymeric particles is reported. The surfactant‐free emulsion polymerization of methyl methacrylate in the presence of the crosslinking reagent 2‐ethyl‐2‐(hydroxy methyl)‐1,3‐propanediol trimethacrylate was used to in situ crosslink colloid micelles to produce stable, crosslinked polymeric particles (diameter size ～ 100–300 nm). A functionalized methacrylate monomer, 2‐methacryloxyethyl‐2′‐bromoisobutyrate, containing a dormant atom transfer radical polymerization (ATRP) living free‐radical initiator, which is termed an inimer (initiator/monomer), was added to the solution during the polymerization to functionalize the surface of the particles with ATRP initiator groups. The surface‐initiated ATRP of different monomers was then carried out to produce core–shell‐type polymeric nanostructures. This versatile technique can be easily employed for the design of a wide variety of polymeric shells surrounding a crosslinked core while keeping good control over the sizes of the nanostructures. The particles were characterized with scanning electron microscopy, transmission electron microscopy, optical microscopy, dynamic light scattering, and Raman spectroscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1575–1584, 2007     

Determination of oxytetracycline residues in matrixes from a freshwater recirculating aquaculture system

This paper describes related procedures to determine the amount of oxytetracycline (OTC) present in trout tissue (muscle with skin attached), biofilter sand, sediment, and tank water from a recirculating aquaculture system. OTC was extracted from the matrixes by different techniques, depending on complexity of the matrix and desired OTC detection level in that matrix. Listed in order of increasing complexity, OTC was extracted from tank water by dilution with acidic buffer containing ethylenediaminetetraacetic acid (EDTA); from biofilter sand by shaking with 0.1 N HCl; from sediment by homogenization and shaking with buffer/EDTA; and from ground trout by homogenization and shaking with buffer/EDTA (twice), with further cleanup and concentration of the extract on a polymeric solid-phase extraction cartridge. The 4 procedures all used the same reversed-phase gradient chromatography on a polymeric column with UV detection at 350 nm. The lower limit of detection (estimated) and upper limit of validation for each of these 4 matrixes were 0.04-4.0 microg/g (ppm; trout), 0.03-20 ppm (biofilter sand), 1-6000 ppm (sediment), and 0.003-10 ppm (water). Recoveries ranged from 82 to 108%, with relative standard deviation <20% over the applicable concentration ranges. These procedures were used to monitor OTC residues resulting from medicated feed administered to rainbow trout in a recirculating aquaculture system.     

Structural modifications of polymers under the impact of fast neutrons

Fast neutron irradiations were performed at room temperature on a series of 13 polymer matrixes having great practical and academic interest. Polymers were irradiated with very low doses of 14 MeV neutrons deposited at reduced dose rate. The modifications of chemical structure of the polymeric matrixes resulting from irradiation were analyzed at the molecular scale by infrared and UV-visible spectroscopy. Particular attention was given to the oxidation occurring in irradiated matrixes during storage in the absence of light at room temperature. In addition the effects of irradiation on the chain arrangements in the polymers were analyzed by Differential Scanning Calorimetry.The most significant result obtained in this preliminary work was evidence that neutron irradiation with very low doses in the range ≈130-320 cGy could provoke structural changes. Indeed, depending on the matrixes, the formation of oxidation products along the macromolecular chains or the evolution of the polymer architecture, evidenced by changes of the T_g or of the crystallinity, was observed. The perspectives of this preliminary work are discussed.     

Investigating resins for solid phase organic synthesis: the relationship between swelling and microenvironment as probed by EPR and fluorescence spectroscopy

The relationship between observed swelling of two cross-linked polystyrene resins and the microenvironment within polymer matrixes has been examined. Polystyrene cross-linked with either divinyl benzene (Merrifield resin) or 1,4-bis(4-vinylphenoxy)butane (JandaJel) was investigated with fluorescence and electron-paramagnetic resonance spectroscopy. Fluorescence spectroscopy revealed a superior correlation between observed swelling and solvation effects using a dansyl probe with JandaJel than with Merrifield resin. However, the internal viscosity of pre-swollen JandaJel is higher than Merrifield resin, as determined by EPR measurements. The combination of these two analytical methods provides insights into the physical differences observed between these two chemically similar resins and suggests caution should be used if using singular physical techniques to probe the microenvironment of polymeric matrixes.     

Fabrication of surface-supported low-dimensional polyimide networks

Interest in thermal and chemical stability of surface-supported organic networks has stimulated recent attempts to covalently interlink adsorbed molecular species into extended nanostructures. We show, using low-temperature scanning tunneling microscopy, that imidization of anhydrides and amines adsorbed on Au(111) can be thermally initiated under controlled ultrahigh vacuum conditions. Using two types of amine-functionalized polyphenyl molecules together with the organic semiconductor PTCDA, monolayer thick linear polymeric strands and a porous polymeric network with nanoscale dimensions are obtained.     

Micro‐Nanostructures of Cellulose‐Collagen for Critical Sized Bone Defect Healing

Bone tissue engineering strategies utilize biodegradable polymeric matrices alone or in combination with cells and factors to provide mechanical support to bone, while promoting cell proliferation, differentiation, and tissue ingrowth. The performance of mechanically competent, micro‐nanostructured polymeric matrices, in combination with bone marrow stromal cells (BMSCs), is evaluated in a critical sized bone defect. Cellulose acetate (CA) is used to fabricate a porous microstructured matrix. Type I collagen is then allowed to self‐assemble on these microstructures to create a natural polymer‐based, micro‐nanostructured matrix (CAc). Poly (lactic‐co‐glycolic acid) matrices with identical microstructures serve as controls. Significantly higher number of implanted host cells are distributed in the natural polymer based micro‐nanostructures with greater bone density and more uniform cell distribution. Additionally, a twofold increase in collagen content is observed with natural polymer based scaffolds. This study establishes the benefits of natural polymer derived micro‐nanostructures in combination with donor derived BMSCs to repair and regenerate critical sized bone defects. Natural polymer based materials with mechanically competent micro‐nanostructures may serve as an alternative material platform for bone regeneration.     

The Influence of Polymer—Selenium Complex Components and the Molecular Weight of the Ionogenic Polymeric Matrix on the Morphologic Characteristics of Selenium-Containing Nanostructures

Several optical methods were used to study nanostructures formed in the reduction of selenium ions in the selenite—ascorbate redox system in an aqueous solution of the poly-N,N,N,N-trimethylmethacryloyloxyethylammonium methyl sulfate polycation. The relation between the molecular weight of the polymeric matrix, which varied over a wide range, M _w = (0.03?13) × 10⁶, and the morphologic characteristics of nanostructures (molecular weight, density, shape, and statistical and hydrodynamic dimensions) was established. The weight ratio between the components of the polymer: selenium complex and the concentration of the polymer in the reaction mixture were shown to substantially influence certain morphologic characteristics of nanostructures. In the region of the formation of stable dispersions, the Gibbs energy of macromolecule—Se⁰ nanoparticle interactions was calculated. The thermodynamic state of solutions of nanostructures was characterized.     

Secondary‐Structure‐Driven Self‐Assembly of Reactive Polypept(o)ides: Controlling Size,Shape, and Function of Core Cross‐Linked Nanostructures

Achieving precise control over the morphology and function of polymeric nanostructures during self‐assembly remains a challenge in materials as well as biomedical science, especially when independent control over particle properties is desired. Herein, we report on nanostructures derived from amphiphilic block copolypept(o)ides by secondary‐structure‐directed self‐assembly, presenting a strategy to adjust core polarity and function separately from particle preparation in a bioreversible manner. The peptide‐inherent process of secondary‐structure formation allows for the synthesis of spherical and worm‐like core‐cross‐linked architectures from the same block copolymer, introducing a simple yet powerful approach to versatile peptide‐based core–shell nanostructures.     

Structure formation in metal complex/polymer hybrid nanomaterials prepared by miniemulsion

Polymer/complex hybrid nanostructures were prepared using a variety of hydrophobic metal β-diketonato complexes. The mechanism of structure formation was investigated by electron paramagnetic resonance (EPR) spectroscopy and small-angle X-ray scattering (SAXS) in the liquid phase. Structure formation is attributed to an interaction between free coordination sites of metal β-diketonato complexes and coordinating anionic surfactants. Lamellar structures are already present in the miniemulsion. By subsequent polymerization the lamellae can be embedded in a great variety of different polymeric matrices. The morphology of the lamellar structures, as elucidated by transmission electron microscopy (TEM), can be controlled by the choice of anionic surfactant. Using sodium alkylsulfates and sodium dodecylphosphate, "nano-onions" are formed, while sodium carboxylates lead to "kebab-like" structures. The composition of the hybrid nanostructures can be described as bilayer lamellae, embedded in a polymeric matrix. The metal complexes are separated by surfactant molecules which are arranged tail-to-tail; by increasing the carbon chain length of the surfactant the layer distance of the structured nanomaterial can be adjusted between 2 and 5 nm.