Comparative Study on Electroanalysis of Fenthion Using Silver Amalgam Film Electrode and Glassy Carbon Electrode Modified with Reduced Graphene Oxide

Oxidation and reduction processes of the insecticide fenthion was comparatively investigated at a reduced graphene oxide modified glassy carbon electrode (RGO‐GCE) and a cyclic renewable silver amalgam film electrode (Hg(Ag)FE) using square wave stripping voltammetry (SWSV). The influence of pH and SW parameters was investigated. The linear concentration ranges were found to be 1 × 10⁻⁶ – 2 × 10⁻⁵ and 1 × 10⁻⁷ – 2 × 10⁻⁵ mol L⁻¹ for Hg(Ag)FE and RGO‐GCE, respectively. The detection and quantification limits were calculated as 1.3 × 10⁻⁷ and 4.5 × 10⁻⁷ mol L⁻¹ for Hg(Ag)FE and 7.6 × 10⁻⁹ and 2.5 × 10⁻⁸ mol L⁻¹ for RGO‐GCE. Both of the developed electroanalytical methods offer rapid and simple detection of fenthion and were used on spiked tap and river water and apple juice samples. Scanning electron microscopy was used for RGO‐GCE surface characterization.     

Electroanalytical Determination of Promethazine Hydrochloride in Pharmaceutical Formulations on Highly Boron‐Doped Diamond Electrodes Using Square‐Wave Adsorptive Voltammetry

The electrochemical oxidation of promethazine hydrochloride was made on highly boron‐doped diamond electrodes. Cyclic voltammetry experiments showed that the oxidation mechanisms involved the formation of an adsorbed product that is more readily oxidized, producing a new peak with lower potential values whose intensity can be increased by applying the accumulation potential for given times. The parameters were optimized and the highest current intensities were obtained by applying +0.78 V for 30 seconds. The square‐wave adsorptive voltammetry results obtained in BR buffer showed two well‐defined peaks, dependent on the pH and on the voltammetric parameters. The best responses were obtained at pH 4.0, frequency of 50 s^?1, step of 2 mV, and amplitude of 50 mV. Under these conditions, linear responses were obtained for concentrations from 5.96×10^?7 to 4.76×10^?6 mol L^?1, and calculated detection limits of 2.66×10^?8 mol L^?1 (8.51 μg L^?1) for peak 1 and of 4.61×10^?8 mol L^?1 (14.77 μg L^?1) for peak 2. The precision and accuracy were evaluated by repeatability and reproducibility experiments, which yielded values of less than 5.00% for both voltammetric peaks. The applicability of this procedure was tested on commercial formulations of promethazine hydrochloride by observing the stability, specificity, recovery and precision of the procedure in complex samples. All results obtained were compared to recommended procedure by British Pharmacopeia. The voltammetric results indicate that the proposed procedure is stable and sensitive, with good reproducibility even when the accumulation steps involve short times. It is therefore very suitable for the development of the electroanalytical procedure, providing adequate sensitivity and a reliable method.     

Lactofen – Electrochemical Sensing and Interaction with dsDNA

The electrochemical reduction of lactofen (LCT) at the glassy carbon (GCE) and silver amalgam film electrode (AMFE) is investigatedin detail by the means of square wave voltammetry (SWV), square wave stripping voltammetry (SWSV) and cyclic voltammetry. The influence of various factors such as supporting electrolyte composition and SW parameters were studied. The AMFE electrode showed an excellent electrochemical activity toward the electro‐reduction of LCT, leading to a significant improvement in sensitivity as compared to the glassy carbon electrode.The SWSV detection limits for GCE and AMFE were 285.0 nM and 2.0 nM, respectively. The applicability of the developed voltammetric method for analysis of tap water and river water is illustrated with spiked samples analysis. Moreover, as lactofen is highly toxic to fish and other aquatic organisms, its interaction with dsDNA isolated from salmon sperm was tested. The intercalative mode of LCT binding to dsDNA was estimated. The heterogeneous rate constants were calculated for the free LCT and the LCT‐dsDNA complex. Moreover, LCT‐dsDNA complex binding ratio and equilibrium constant were determined. The decrease in the SWV peak current of LCT in the presence of dsDNA was used for the determination of dsDNA.     

An Electrochemical Sensor Based on Silver Nanoparticles‐Benzalkonium Chloride for the Voltammetric Determination of Antiviral Drug Tenofovir

A simple voltammetric nanosensor was described for the highly sensitive determination of antiviral drug Tenofovir. The benzalkonium chloride and silver nanoparticles were associated to build a nanosensor on glassy carbon electrode. Surface characterictics were achieved using scanning electron microscopic technique. The voltammetric measurements were performed in pH range between 1.0 and 10.0 using cyclic, adsorptive stripping differential pulse and adsorptive stripping square wave voltammetry. The linear dependence of the peak current on the square root of scan rates and the slope value (0.770) demonstrated that the oxidation of tenofovir is a mix diffusion‐adsorption controlled process in pH 5.70 acetate buffer. The linearity range was found to be 6.0×10⁻⁸–1.0×10⁻⁶ M, and nanosensor displayed an excellent detection limit of 2.39×10⁻⁹ M by square wave adsorptive stripping voltammetry. The developed nanosensor was successfully applied for the determination of Tenofovir in pharmaceutical dosage form. Moreover, the voltammetric oxidation pathway of tenofovir was also investigated at bare glassy carbon electrode comparing with some possible model compounds (Adenine and Adefovir).     

Electrocatalytic Application of Girard's Reagent T to Simultaneous Determination of Furaldehydes in Pharmaceutical and Food Matrices by Highly Sensitive Voltammetric Methods

Sensitive and precise voltammetric methods for the determination of trace amounts of furaldehydes, mainly as furfural (F) and 5‐hydroxymethyl‐2‐furaldehyde (HMF), in foods, pharmaceutical and other matrices is described. Determination of total furaldehyde at <μg g^?1 levels in alkaline buffered aqueous media was individually investigated. By the use of ordinary SWV and adsorptive square wave stripping voltammetry (Ad‐SWSV), the detection limits for determination of F and HMF found to be 400 and 10 ng g^?1, respectively. At a 1.0 μg g^?1 level of furfural in sample, the relative standard deviation (n=4) was 2.79%. The application of Ad‐SWSV to the determination of F and HMF, after their in situ derivatization with trimethylaminoacetohydrazide chloride (Girard's reagent T) at a static mercury drop electrode (SMDE) in NH₃‐NH₄Cl buffer of pH 9.5, resulted in a limit of detection of 10 ng g^?1 for the resolved peaks of HMF and F. The results obtained by the proposed method for the real samples were compared with the corresponding results from UV‐spectrophotometry and HPLC experiments in various matrices.     

Carbon‐Based Electrodes for Sensitive Electroanalytical Determination of Aminonaphthalenes

The electroanalytical performance of bare glassy carbon electrodes (GCE) for the determination of 1‐aminonaphthalene (1‐AN) and 2‐aminonaphthalene (2‐AN) was compared with GCE modified by a Nafion permselective membrane or multiwalled carbon nanotubes and with other types of carbon‐based materials, carbon film and boron doped diamond. Nafion‐modified GCE gave the highest sensitivity and lowest detection limit (0.4 µmol L^?1) for differential pulse voltammetric determination of 1‐AN. Electrochemical impedance spectroscopy gave information about the processes at the electrode surface. Simultaneous determination of 1‐AN and 2‐AN in a mixture at GCE and their determination in model samples of river water is presented.     

Sensitive Determination of Trace Pb2+ in Seawater Using Columnar Glassy Carbon Electrode

We herein report a mercury‐free approach for the sensitive determination of trace Pb²⁺ in seawater using differential pulse stripping voltammetric (DPSV) method with a novel columnar glassy carbon electrode (CGCE). Compared with the conventional disk glassy carbon electrode with the same diameter, it has much larger electrochemical area (0.627 ± 0.003 cm²). The CGCE shows good accumulation ability and consequently acceptable behavior which makes it suitable as a working electrode in the DPSV determination of Pb2+ with the great advantage of the avoidance of harmful mercury. Using acidified artificial seawater as supporting electrolyte, there was a good linear relationship between the peak currents and the concentration of Pb²⁺ in the range of 0.6～140.0 μg L^‐1 with a detection limit of 0.3 μg/L (S/N = 3) when the accumulation time was 300 s. The method was employed to determine trace levels of Pb²⁺ in real seawater samples successfully.     

Voltammetric Determination of 4‐Nitrophenol and 5‐Nitrobenzimidazole Using Different Types of Silver Solid Amalgam Electrodes – A Comparative Study

The voltammetric behavior of two genotoxic nitro compounds (4‐nitrophenol and 5‐nitrobenzimidazole) has been investigated using direct current voltammetry (DCV) and differential pulse voltammetry (DPV) at a polished silver solid amalgam electrode (p‐AgSAE), a mercury meniscus modified silver solid amalgam electrode (m‐AgSAE), and a mercury film modified silver solid amalgam electrode (MF‐AgSAE). The optimum conditions have been evaluated for their determination in Britton‐Robinson buffer solutions. The limit of quantification (L_Q) for 5‐nitrobenzimidazole at p‐AgSAE was 0.77 µmol L^?1 (DCV) and 0.47 µmol L^?1 (DPV), at m‐AgSAE it was 0.32 µmol L^?1 (DCV) and 0.16 µmol L^?1 (DPV), and at MF‐AgSAE it was 0.97 µmol L^?1 (DCV) and 0.70 µmol L^?1 (DPV). For 4‐nitrophenol at p‐AgSAE, L_Q was 0.37 µmol L^?1 (DCV) and 0.32 µmol L^?1 (DPV), at m‐AgSAE it was 0.14 µmol L^?1 (DCV) and 0.1 µmol L^?1 (DPV), and at MF‐AgSAE, it was 0.87 µmol L^?1 (DCV) and 0.37 µmol L^?1 (DPV). Thorough comparative studies have shown that m‐AgSAE is the best sensor for voltammetric determination of the two model genotoxic compounds because it gives the lowest L_Q, is easier to prepare, and its surface can be easily renewed both chemically (by new amalgamation) and/or electrochemically (by imposition of cleaning pulses). The practical applicability of the newly developed methods was verified on model samples of drinking water.     

Electroanalytical Determination of Lidocaine in Pharmaceutical Preparations Using Boron‐Doped Diamond Electrodes

A new electroanalytical procedure was developed for the determination of lidocaine in commercial local anesthetics products containing lidocaine as the active ingredient. The procedure is based on the use of electrochemical methods as cyclic and square‐wave voltammetry, with boron‐doped diamond electrodes. The oxidation of lidocaine in Britton–Robinson buffer (0.1 mol L^?1) using this type of electrode gives rise to one irreversible peak in 1.68 V (versus Ag/AgCl). The detection and quantification limits obtained from pure water were 10.0 and 34.4 μg/L, respectively. The proposed electrochemical method was also successfully applied to the analysis of commercially available pharmaceutical preparations. The electrochemical responses of pharmaceutical preparations (gels) were identical to those of standard lidocaine. No influence of propyleneglycol present in the gels on the voltammetric responses was observed. Lidocaine recoveries ranged from 97.6% to 99.2%.     

Iodine‐mediated Oxidation of Resveratrol. An Electroanalytical Study Using Platinum and Glassy Carbon Electrodes

Resveratrol is a phenolic compound that shows important biological antioxidant activities. In this paper, the electrochemical oxidation of iodide in the presence of resveratrol was investigated using both platinum and glassy carbon electrodes. The experimental results showed a diffusion controlled process for the oxidation of iodide to iodine, followed by the chemical reaction of iodine with resveratrol. The possible applicability of iodine‐mediated reaction in the quantitative analysis of resveratrol was studied, obtaining sensitivities of 0.98±0.03 and 4.22±0.20 μAμM^?1 cm^?2 using platinum and glassy carbon electrodes, respectively. The resveratrol content in a sample obtained from the extracellular medium of elicited suspension‐cultured cells of Vitis vinifera was evaluated and compared with data obtained by HPLC analysis, with good correlations. The signal of other compounds that may be present in the samples or they are precursors of the biosynthesis of trans‐resveratrol (L‐ascorbic, glycine, saccharose, tyrosine, cinnamic acid and p‐coumaric acid) was also evaluated, which shows lower interferences when using glassy carbon electrodes.     

Electrochemical Investigation of Ruxolitinib: Sensitive Voltammetric Assay in Drug Product and Human Serum by Using Different Solid Electrodes

Ruxolitinib (RUX), a compound of the pyrrolopyrimidines class with activity as a tyrosine kinase inhibitory drug, is used to treat myelofibrosis. This study is reported for the detailed electrochemical behavior of RUX. The effects of supporting electrolyte, pH, and scanning rate on the peak potentials and currents of RUX were investigated by BDDE and GCE using different voltammetric techniques. Under optimum experimental conditions, calibration curves for RUX were obtained as 4 μM–80 μM and 1 μM–80 μM with a limit of detection (LOD) of 0.517 μM and 0.192 μM by the GCE and BDDE, respectively using DPV.     

Sensitive Electrochemical Determination of Hydrogen Peroxide Using Copper Nanoparticles in a Polyaniline Film on a Glassy Carbon Electrode

Rapid and accurate determination of hydrogen peroxide is necessary in biochemistry and environmental science. In this paper, a sensitive hydrogen peroxide electrochemical sensor was developed by cyclic voltammetry deposition of polyaniline–copper nanocomposite film on a glassy carbon electrode. The synthesized polyaniline/Cu composites were characterized by scanning electron microscopy and X-ray diffraction. With a typical working potential of 0.4?V (versus Ag/AgCl) and a pH value of 6.0, the prepared electrochemical sensor achieved linear range of 1.0–500?µM for hydrogen peroxide detection. A relative standard deviation of 4.9% for n?=?7 and 10.0?µM of H₂O₂ and a limit of detection of 0.33?µM at a signal-to-noise ratio?=?3 were observed. The sensor was successfully used for the analysis of tap water, and a spiked recovery of 93.0?±?2.1% was obtained, further confirming the sensor’s accuracy and feasibility.     

Development of Electroanalytical Methods Using Different Electrodes for the Determination of Progesterone (P4) in Pharmaceutical Formulations and Human,Cow and Goat Milk

For the determination of progesterone (P4) electroanalytical studies were performed using mercury electrode (HMDE) and screen-printed boron-doped diamond electrode (BDD-SPE). The effects of pH, supporting electrolyte, accumulation potential and time (E_acc, t_acc) were studied in both systems. The optimum conditions were: i) HMDE: pH 7,0; E_acc: −0,1 V and t_acc: 40 s, ii) BDD-SPE: 0,5 mol L⁻¹ H₂SO₄; E_acc: 0,0 V and t_acc: 120 s. Under these conditions, the detection limit was 3.1 μg L⁻¹ for HMDE and 45.6 μg L⁻¹ for BDD-SPE. Both methods were validated and applied in the P4 determination on pharmaceutical formulations and milk samples.     

Electroanalytical Determination of Opipramol in Pharmaceutical Preparations and Biological Fluids

Abstract

The electrooxidative behavior and determination of opipramol, a tricyclic compound for therapy of anxious-depressive states and general anxiety disorder, were investigated at a glassy carbon electrode using cyclic, linear sweep, differential pulse and Osteryoung square wave voltammetric techniques. The oxidation of opipramol was irreversible and exhibited a diffusion controlled process dependent on pH using a glassy carbon electrode. The oxidation mechanism on a glassy carbon electrode is proposed and discussed. The anodic process can be attributed to the oxidation of azepine and piperazine rings. Different parameters were tested to optimize the conditions for the determination of opipramol. The dependence of current intensities and potentials on pH, concentration, scan rate, and nature of the buffer was investigated as detailed. Opipramol in pH 3.7 acetate buffer presents a well-defined anodic response at + 0.86 V according to studies of the proposed method. The determination of opipramol was in pH 3.7 acetate buffer, which allowed quantitation over the 2 × 10^?6 to 2 × 10^?4 M range in the supporting electrolyte, 2 × 10^?6 to 6 × 10^?5 M range in the spiked serum sample, and 2 × 10^?6 to 1 × 10^?4 M range in the urine sample, for both techniques. The proposed method was applied to commercial drageés and average percente recovery was in agreement with that obtained by spectrophotometric comparison methods. The method was extended to the in vitro determination of opipramol in spiked human serum and urine.     

Carbon Paste Electrodes Modified with Graphene Oxides – Comparative Electrochemical Studies of Thioguanine

The voltammetric study of thioguanine (TG) was comparatively investigated on bare, graphene oxide and reduced graphene oxide modified carbon paste electrodes using cyclic (CV) and square wave stripping (SWSV) voltammetric techniques. Depending on the working electrode and pH of supporting electrolyte, characteristic electrochemical behaviour of thioguanine was established and the mechanism of TG oxidation was suggested. Based on the obtained results, the new voltammetric method for TG determination in buffer solutions and pharmaceutical formulation was developed. Atomic force microscopy was used to characterize electrodes surfaces.     

Characterization and Use of Copper Solid Amalgam Electrode for Electroanalytical Determination of Triazines‐Based Herbicides

This paper reports the construction, characterization and use of copper solid amalgam electrode in the study of the electrochemical behavior of atrazine and ametryne herbicides by square‐wave voltammetry. This study was used as basis for the development of sensitive analytical methods for the determination of these herbicides in natural water, avoiding the use of mercury, by means of a solid electrode that presents high sensitivity and minimizes any environment contamination with mercury residues. The experimental and voltammetric conditions were evaluated and the results showed a reduction peak for atrazine at ?0.98 and at ?1.1 V vs. Ag/AgCl 3.0 mol L^?1 for ametryne, both with characteristic of an irreversible electrode reaction in an electrochemical diffusion controlled process, involving two electrons for each herbicide reduction. Based on voltammetric studies, it has been demonstrated that the most possible mechanism for the reduction of herbicides involved reduction of bond carbon‐chloride for atrazine and the reduction of bond carbon–SCH₃ for ametryne. The detection limit of herbicides obtained in pure water (laboratory samples) was shown to be lower than the maximum limit of residue established for natural water by the Brazilian Environmental Agency, demonstrating that this methodology is very suitable for determining any contamination by atrazine and ametryne residues in different samples, proving a good substitute for mercury electrodes.     

Voltammetric Behavior and Determination of Cinnarizine in Pharmaceutical Formulations and Serum

Abstract

The electrochemical reduction of cinnarizine was investigated by cyclic and linear sweep adsorptive voltammetry at glassy carbon electrode in Britton-Robinson buffers over the pH range 2.5–11.5. For analytical purposes, a well-defined adsorption-controlled cathodic peak was obtained at pH 2.5. By cathodic adsorptive linear sweep voltammetry, a linear calibration plot was obtained in the range of 2.0 × 10^?7 to 5.0 × 10^?6 mol L^?1 with detection limit of 9.0 × 10^?9 mol L^?1. The method was successfully applied to the determination of cinnarizine in commercial formulations with mean recovery and relative standard deviation of 100.24% and 1.46, respectively. The proposed method was also applied for drug determination in spiked serum samples by applying the standard addition method with a mean recovery of 97.80% and standard deviation of 3.06.     

Modified Glassy Carbon Electrode with Multiwall Carbon Nanotubes as a Voltammetric Sensor for Determination of Leucine in Biological and Pharmaceutical Samples

Abstract

A simple and highly sensitive method is described for voltammetric determination of leucine in blood and urine samples; namely, a glassy carbon electrode with an effective method is modified with multiwall carbon nanotubes (MWNTs). The cyclic voltammetric results indicated that MWNTs remarkably enhanced electrocatalytic activity toward the oxidation of leucine. Under the optimum condition the calibration curve was linear in the concentration range 9.0 × 10^?6 ? 1.5 × 10^?3 mol L^?1, with the detection limit of 3.0 × 10^?6 mol L^?1 and a relative standard deviation (RSD%) lower than 3.0% (n = 5). Also, some kinetic parameters were determined and a multistep mechanism for oxidation of leucine was proposed.     

Sensitive Simultaneous Determination of o-Nitrophenol and p-Nitrophenol in Water by Surfactant-Mediated Differential Pulse Voltammetry

A simple, low-cost and sensitive electroanalytical method was developed for the simultaneous determination of p-nitrophenol and o-nitrophenol isomers in water samples at a glassy carbon electrode (CGE) in the presence of cationic surfactant. The electrochemical behavior of p-nitrophenol and o-nitrophenol was studied by cyclic voltammetry (CV) in 0.1?mol L^?1 acetate/acetic acid buffer (pH 3.70) in the presence and absence of cetylpyridinium bromide. The resolution of overlapped cathodic peaks potentials (E_pc) of isomers was successfully improved in the presence of 100.0?µmol L^?1 cetylpyridinium bromide, thus making this approach ideal for the simultaneous determination of isomers. Under the optimized conditions in 0.05?mol L^?1 HEPES buffer at pH 7.0 using differential pulse voltammetry (DPV) at a scan rate of 45?mV s^?1, pulse amplitude of 220?mV and modulation time of 10?ms, limits of detection 0.59?µmol L^?1 for p-nitrophenol and 1.14?µmol L^?1 for o-nitrophenol were obtained with linear ranges from 2.0 to 60.0?µmol L^?1 and 3.0 to 60.0?µmol L^?1, respectively. The intraday precision was assessed as relative standard deviation (%) for 20.0 and 40.0?µmol L^?1 concentrations were 4.30% and 2.41% for p-nitrophenol and 4.87% and 2.20% for o-nitrophenol, respectively. The developed method was applied for the determination of the isomers in lake water samples. The accuracy was attested by comparison with high-performance liquid chromatography with diode array detection (HPLC-DAD) as a reference analytical technique. Recovery values ranging from 90.3% to 111.8% also attested to the accuracy of method for analysis of real samples.     

Voltammetric Determination of Cymoxanil and Famoxadone at Different Types of Carbon Electrodes

Differential pulse voltammetry (DPV) at a carbon fibre rod electrode (CFRE) and a capillary carbon paste electrode (CPE) have been used for the determination of pesticides cymoxanil and famoxadone, respectively. In the cathodic potential range, optimum conditions were found for the determination of cymoxanil by DPV at CFRE at pH 4 with limit of quantification (L_Q) of 5.9×10^?7 mol L^?1. In the anodic area, determination of famoxadone by DPV at CPE was performed at optimum pH 2 with L_Q=1.4×10^?7 mol L^?1. Practical applicability of the newly developed methods was verified on spiked samples of river water and soil.