Electrochemical performance of surfactant-processed LiFePO4 as a cathode material for lithium-ion rechargeable batteries

This study focuses on the effect of addition of surfactant as a dispersing agent during vibratory ball milling of LiFePO₄ (LFP) precursor materials on the electrochemical performance of solid-state reaction synthesized LFP for lithium-ion battery cathode material. LFP particles formed after calcinations of ball milled LFP precursors (Li₂CO₃, FeC₂O₄, and NH₄H₂PO₄) showed better size uniformity, morphology control, and reduced particle size when anionic surfactant (Avanel S-150) was used. The specific surface area of LFP particles increased by approximately twofold on addition of surfactant during milling. These particles showed significantly enhanced cyclic performance during charge/discharge due to a reduced polarization of electrode material. Electrodes fabricated from LFP particles by conventional milling process showed a 22 % decrease in capacity after 50 cycles, whereas the performance of electrode prepared by surfactant processed LFP showed only 3 % loss in capacity. The LFP particles were characterized using XRD, FE-SEM, particle size distribution, density measurement, and BET-specific surface area measurement. Electrochemical impedance spectra and galvanostatic charge/discharge test were performed for the electrochemical performance using coin-type cell.     

Enhanced electrochemical performances of layered LiNi0.5Mn0.5O2 as cathode materials by Ru doping for lithium-ion batteries

Ionics - The pristine and Ru-doped LiNi0.5Mn0.5O2 cathode materials are synthesized by a wet chemical method, followed by a high-temperature calcination process. The influence of Ru substitution on...     

Excellent long-term electrochemical performance of graphite oxide as cathode materials for lithium-ion batteries

A facile, scalable route has been adopted to synthesize graphite oxides with different degrees of oxidation. Subsequently, graphite oxides with rationally designed functional groups have been utilized as cathode materials for lithium-ion batteries (LIBs). The electrodes deliver the initial and second discharge capacities of 332 and 172 mAh g^?1 at a current density of 0.1 A g^?1, respectively. More importantly, a remarkable long-term cycling performance of 130 mAh g^?1 after 800 cycles has been gathered, with an ultralow capacity fading of 0.03% per cycle from the second cycle. The root cause of excellent cycling stability should be ascribed to the admirable reversibility of epoxy and carbonyl groups in graphite oxides during the Li-cycling. Meanwhile, the deep study has provided a novel way to avoid complex and expensive post-treatment process of graphite oxides, whose synthesis conditions are also optimized. Those striking features make graphite oxides as promising cathode materials for lithium-ion batteries.     

Hydrothermal synthesis and electrochemical performance studies of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 for lithium-ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ nanocrystallites were synthesized by a one-step hydrothermal method, and uniform second particles were formed by a subsequent calcination process. X-ray diffraction results indicate that the as-synthesized material can be indexed by α-NaFeO₂ layered structure with R-3 m space group. The results of Rietveld refinements show the I ₀₀₃/I ₁₀₄ value of the material is 2.032, and the nanostructured material presents low cation mixing, small cell volume, and a consequent suppression of lattice strain. The rate performances of the as-synthesized material can be further improved by coating Al₂O₃. The discharging capacity of Al₂O₃-coated material reaches 154.4 mAh g^?1, and the capacity retention maintains 80.3 % after 50 cycles at 5 C in the voltage range of 2.5 to 4.5 V, while those of the bare one is only 139.0 mAh g^?1 and 71.6 %, respectively. The transmission electron microcopy observation shows no zigzag layer exists on the surface of particle after cycles for Al₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂. Compared to bare LiNi_1/3Co_1/3Mn_1/3O₂, the de-intercalation potential difference before and after cycles of Al₂O₃-coated one is smaller. This indicates that Al₂O₃ coating can reduce the electrochemistry polarization in the electrode bulk.     

Synthesis and electrochemical performance of LiNi0.6Co0.2Mn0.2O2/reduced graphene oxide cathode materials for lithium-ion batteries

A LiNi_0.6Co_0.2Mn_0.2O₂/reduced graphene oxide (RGO) composite with RGO content of 1.2 % was prepared by a simple spray-drying method instead of high-energy ball milling method. The composite has been characterized by X-ray diffraction, scanning electron microscope, transmission electron microscopy, energy dispersive spectroscopy, and charge/discharge test. The X-ray diffractometry result showed that composite possessed a typical hexagonal structure. The RGO sheets served as efficient electronically conductive frameworks benefitting from its 2D structure and outstanding electronic conductivity. The scanning electron microscope and transmission electron microscopy verified that LiNi_0.6Co_0.2Mn_0.2O₂ particles were wrapped with RGO sheets, which facilitated electronic conductivity between particles. The electrochemical results indicated that composite delivered a higher discharge capacity at various discharge rates. The cycling performance was also evaluated. The composite exhibited better cycling performance than pristine sample. Electrochemical impedance spectroscopy showed that the RGO can greatly reduce the charge transfer resistance. The results here gave clear evidence of RGO to improve electrochemical performance.     

Synthesis and characterization of mixed vanadium oxide cathode materials for lithium-ion batteries

A family of mixed vanadium oxides LiCo_yNi_(1−y)VO₄ (x=0.2, 0.5 and 0.8) of potential use as high voltage cathode materials in lithium batteries, has been synthesized and characterized. In general the x-ray diffraction analysis showed that these compounds have an inverse spinel structure where about 85 % of the Ni²⁺ and Co²⁺ ions occupies octahedral sites and the rest tetrahedral sites along with the V⁵⁺ ions. Moreover, the annealing temperature plays a key role in determining the particle size, as demonstrated by scanning electron microscope analysis. Cycling voltammetry tests showed that the lithium insertion-extraction process in the LiCo_yNi_(1−y)VO₄ electrode materials occurs reversibly at around 4.3–4.4 V vs. Li and these results are confirmed by cycling tests. The cycling capacity is modest; however the trend of the cycling curves leads to foresee that an increase in capacity may be obtained by extending the charging process beyond 4.6 V vs. Li, once a stable electrolyte will be available. Paper presented at the 6th Euroconference on Solid State Ionics, Cetraro, Calabria, Italy, Sept. 12–19, 1999.     

Enhanced electrochemical performance of La- and Zn-co-doped LiMn2O4 spinel as the cathode material for lithium-ion batteries

We report on the nanoparticle uptake into MCF10A neoT and PC-3 cells using flow cytometry, confocal microscopy, SQUID magnetometry, and transmission electron microscopy. The aim was to evaluate the influence of the nanoparticles?? surface charge on the uptake efficiency. The surface of the superparamagnetic, silica-coated, maghemite nanoparticles was modified using amino functionalization for the positive surface charge (CNPs), and carboxyl functionalization for the negative surface charge (ANPs). The CNPs and ANPs exhibited no significant cytotoxicity in concentrations up to 500???g/cm³ in 24?h. The CNPs, bound to a plasma membrane, were intensely phagocytosed, while the ANPs entered cells through fluid-phase endocytosis in a lower internalization degree. The ANPs and CNPs were shown to be co-localized with a specific lysosomal marker, thus confirming their presence in lysosomes. We showed that tailoring the surface charge of the nanoparticles has a great impact on their internalization.     

Structure and electrochemical characteristics of LiFePO4 cathode materials for rechargeable Li-Ion batteries

Complex investigations of cathode materials for rechargeable lithium-ion batteries have been carried out using the following techniques: scanning electron microscopy, microanalysis, extended X-ray absorption fine structure (EXAFS) spectroscopy, Mössbauer spectroscopy, and porosimetry. Investigations have been performed on samples prepared according to the original technology at the St. Petersburg State Institute of Technology (Technical University) (SPbSTI (TU)) and on four commercial cathode materials. It has been established that there is a correlation between the nanostructured morphology of the cathode materials, their chemical composition, and electrochemical capacity. It has been found that the internal resistance of the LiFePO₄ cathode material is linearly dependent on the diffusion coefficient of lithium ions. The valence state and local coordination of Fe ions have been studied using the ⁵⁷Fe Mössbauer effect. It has been shown that more than 90% of the iron ions are in the valence state Fe²⁺. Based on the data available in the literature on the methods of synthesizing LiFePO₄ and data on the diagnosis of the studied samples, conclusions have been drawn about a modification of the synthesis for producing high-quality cathode materials for Li-ion batteries.     

Synthesis and electrochemical performance of carbon-coated LiMnBO<Subscript>3</Subscript> as cathode materials for lithium-ion batteries

Carbon-coated LiMnBO₃/C is synthesized by a sol-gel method using polyethylene glycol 6000 (PEG-6000) as carbon source. The influences of different sintering temperatures on the crystal structure, morphology, and electrochemical performance of LiMnBO₃/C composites are investigated. XRD results indicate that the samples consist of the monoclinic phase LiMnBO₃ (m-LiMnBO₃) and the hexagonal phase LiMnBO₃ (h-LiMnBO₃), and the amount of m-LiMnBO₃ is reduced and the h-LiMnBO₃ is increased with the increasing sintering temperature. The particle size of the samples is about 500 nm, and the surface of the particles is coated with a thick amorphous carbon layer. The LiMnBO₃/C synthesized at 750 °C exhibits the initial discharge capacities of 213.4, 170.8, and 109.7 mAh g^?1 at 0.025, 0.05, and 0.5 C rates, respectively, and shows better cycling performance than that of bare LiMnBO₃. The enhanced electrochemical performance might be largely attributed to the uniformly coated carbon layers from decomposition of the PEG-6000.     

Synthesis and electrochemical performance of carbon-coated LiCoBO<Subscript>3</Subscript> as cathode materials for lithium-ion batteries

Carbon-coated LiCoBO₃ (LiCoBO₃/C) is prepared by sol-gel method and polyethylene glycol 6000 (PEG-6000) is chosen as carbon source. The LiCoBO₃/C sample exhibits an initial discharge capacity of 76.7 mAh g^?1 at 0.1 C, and it can deliver a discharge capacity of 65.9 mAh g^?1 after 50 cycles, while the LiCoBO₃ sample only presents a first discharge capacity of 34.3 and 16.8 mAh g^?1 at the 50th cycle, LiCoBO₃/C sample shows better cycling performance than that of LiCoBO₃. The improved electrochemical properties could be mainly ascribed to the conductive carbon network and the reduced particle size of the LiCoBO₃ powders. Electrochemical impedance spectroscopy (EIS) results confirm that carbon coating decreases the charge transfer resistance and improve the electrochemical reaction kinetics.     

一代材料，一代电池：正极材料研究推动锂离子动力电池的升级换代

一代材料,一代电池。锂离子电池正极材料的研究不断推动着动力电池的升级换代。第一代动力电池的正极材料为锰酸锂LiMn₂O₄,其低温性能好、成本低和安全性高,但电池能量密度不够高。第二代动力电池正极材料为磷酸铁锂LiFePO₄和三元正极材料镍钴锰NCM/镍钴铝NCA。磷酸铁锂正极材料的优势是长寿命、低成本、高安全性。三元锂正极材料的特点是大容量、高能量密度、快充效率高。第三代动力电池的正极材料是高电压镍锰酸锂LiNi_0.5Mn_1.5O₄和镍酸锂LiNiO₂,主要解决第二代面临的低成本和长续航不能兼顾的问题以及更长里程问题。文章首先回顾第一、二代的锰酸锂、磷酸铁锂和三元正极材料的研究历程、优缺点及发展近况,之后介绍和展望下一代高电压镍锰酸锂和镍酸锂正极材料。     

Modified carbothermal synthesis and electrochemical performance of LiFePO4/C composite as cathode materials for lithium-ion batteries

LiFePO₄/C active materials were synthesized via a modified carbothermal method, with a low raw material cost and comparatively simple synthesis process. Rheological phase technology was introduced to synthesize the precursor, which effectively decreased the calcination temperature and time. The LiFePO₄/C composite synthesized at 700 °C for 12 h exhibited an optimal performance, with a specific capacity about 130 mAh g^?1 at 0.2C, and 70 mAh g^?1 at 20C, respectively. It also showed an excellent capacity retention ratio of 96 % after 30 times charge–discharge cycles at 20C. EIS was applied to further analyze the effect of the synthesis process parameters. The as-synthesized LiFePO₄/C composite exhibited better high-rate performance as compared to the commercial LiFePO₄ product, which implied that the as-synthesized LiFePO₄/C composite was a promising candidate used in the batteries for applications in EVs and HEVs.     

Enhanced cyclability of triple-metal-doped LiMn2O4 spinel as the cathode material for rechargeable lithium batteries

To improve the cycle performance of spinel LiMn₂O₄ as the cathode of 4-V-class lithium secondary batteries, spinel phases LiM _x Mn_2 − x O₄ (M=Li, Fe, Co; x = 0, 0.05, 0.1, 0.15) and LiFe_0.05M _y Mn_{1.95 − y} O₄ (M=Li, Al, Ni, Co; y = 0.05, 0.1) were successfully prepared using the sol–gel method. The spinel materials were characterized by powder X-ray diffraction (XRD), elemental analysis, and scanning electron microscopy. All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. Electrochemical studies were carried out using the Li|LiM _x Mn_2 − x O₄ (M=Li, Fe, Co; x = 0, 0.05, 0.1, 0.15) and LiFe_0.05M _y Mn_{1.95 − y} O₄ (M=Li, Al, Ni, Co; y = 0.05, 0.1) cells. These cathodes were more tolerant to repeated lithium extraction and insertion than a standard LiMn₂O₄ spinel electrode in spite of a small reduction in the initial capacity. The improvement in cycling performance is attributed to the stabilization in the spinel structure by the doped metal cations.     

Malonic acid-assisted synthesis of LiNi0.8Co0.2O2 cathode active material for lithium-ion batteries

Polycrystalline LiNi_0.8Co_0.2O₂ was synthesized by a solution route with malonic acid as the complexing agent. The effects of temperature, duration of heat treatment, pH of the precursor solution, and the nature of the solvent employed on the performance characteristics of the product were studied. It was observed that a 12-hour 800 °C heat treatment protocol was necessary to obtain products with optimal electrochemical characteristics. Furthermore, an excess lithium stoichiometry of 1.05 was found to be detrimental to the performance of the cathode material. The beneficial effect of ethanol as a solvent over water on the product characteristics is explained by the presence of solvent molecules in the coordination sphere of the cations. A pH of 7, at which malonic acid is complexed completely with the cations without interference from other nucleophiles, was found to be ideal for the synthesis of the cathode active material from aqueous solutions. With ethanol as the medium, the product formed by a 12-h calcination at 800 °C yielded a first-cycle capacity of 173 mAh/g and a tenth-cycle capacity of 169 mAh/g.     

4-Volt cathode materials for rechargeable lithium batteries wet-chemistry synthesis, structure and electrochemistry

Lithium transition-metal oxides used as intercalation compounds for rechargeable lithium batteries are widely studied in search of structural stability and improved electrochemical performance. Cathode materials belonging to the 4-volt class electrodes were synthesized by wet-chemistry methods, i.e., sol-gel, combustion or co-precipitation techniques. It is shown that synthesis greatly affects the electrochemistry and cycle life characteristics of the cathodes. Extensive damage including local strain variation, nanodomain formation, and changes in cation ordering, has been observed by local probes such as Raman and FTIR spectroscopy. In this work we wish to show the relationship between the local cationic environment and electrochemical characteristics of the 4-volt cathodes. Materials such as LiMn₂O₄, LiCoO₂, LiNi_1−yCo_yO₂, LiNi_1−yCo_yVO₄, and LiMoVO₆ are investigated.     

Synthesis of sea urchin-like LiMn2O4 hollow macrospheres via in situ conversion for rechargeable lithium-ion batteries

Among several materials (transition metal oxide) under development for use as a cathode in lithium-ion batteries, cubic spinel LiMn₂O₄ is one of the most promising cathode materials. In this study, the sea urchin-like LiMn₂O₄ hollow macrospheres were synthesized by using sea urchin-like α-MnO₂ precursors through solid-state in situ self-sacrificing conversion route. The as-prepared LiMn₂O₄ was assembled by many single-crystalline “thorns” of ca.10–20 nm in diameter and ca. 400–500 nm in length. Galvanostatic battery testing showed that sea urchin-like LiMn₂O₄ had an initial discharge capacity of 126.8 mAh/g at the rate of 0.2 C in the potential range between 3.0 and 4.5 V. More than 96.67 % of the initial discharge capacity was maintained for over 50 cycles. The improved electrochemical properties were attributed to the reduced particle size and enhanced electrical contacts by the materials. This particular sea urchin-like structured composite conceptually provides a new strategy for designing electrodes in energy storage applications.     

Electrochemical and structural properties of MoO3–V2O5 nanocomposite thin film electrodes for lithium rechargeable batteries

We have investigated the electrochemical properties of V₂O₅-based thin film electrodes as a function of the amount of MoO₃ by means of X-ray diffraction (XRD), X-ray photoemission spectroscopy (XPS), and transmission electron microscopy (TEM). XRD results show that the V₂O₅-based thin film electrodes give an amorphous characteristic. XPS results reveal the formation of V₂O₅ and MoO₃ phases. TEM results show that MoO₃ dots (5–30 nm in size) are embedded in the amorphous V₂O₅ matrix. It is further shown that cells fabricated with the MoO₃–V₂O₅ nanocomposite thin film electrodes give better cycling performance than those made with the single V₂O₅ thin film electrodes. A possible explanation for the MoO₃ nano-dot dependence on the cycling performance of the V₂O₅-based thin film electrodes is described.     

Mg-doped layered oxide cathode for Na-ion batteries

Na-ion batteries (NIBs) are regarding as the optimum complement for Li-ion batteries along with the rapid development of stationary energy storage systems. In order to meet the commercial demands of cathodes for NIBs, O3-type Cu containing layered oxide Na_0.90Cu_0.22Fe_0.30Mn_0.48O₂ with good comprehensive performance and low-cost element components is very promising for the practical use. However, only part of the Cu³⁺/Cu²⁺ redox couple participated in the redox reaction, thus impairing the specific capacity of the cathode materials. Herein, Mg²⁺-doped O3-Na_0.90Mg_0.08Cu_0.22Fe_0.30Mn_0.40O₂ layered oxide without Mn³⁺ was synthesized successfully, which exhibited improved reversible specific capacity of 118 mAh/g in the voltage range of 2.4-4.0 V at 0.2 C, corresponding to the intercalation/deintercalation of 0.47 Na⁺ (0.1 more than that of Na_0.90Cu_0.22Fe_0.30Mn_0.48O₂). This work demonstrates an important strategy to obtain advanced layered oxide cathodes for NIBs.     

Improving the cycle stability and rate performance of LiNi0.91Co0.06Mn0.03O2 Ni-rich cathode material by La2O3 coating for Lithium-ion batteries

In this wok, a uniform layer of La₂O₃ is coated on the surface of LiNi_0.91Co_0.06Mn_0.03O₂ Ni-rich cathode material by using a wet coating process. The XPS and EDX analysis confirms the presence of La₂O₃ coating on the surface of NCM. The coated samples deliver the superior electrochemical performance, 0.2 wt % La₂O₃ (LaO-0.2) NCM exhibits discharge capacity of 202.7 mAh g⁻¹ in 1^st cycle and delivered the cycle stability of 87.2% after 100 cycles. Besides, the enhanced capacity retention, LaO-0.2 has delivered very high discharge capacity of 80.3 mAh g⁻¹ at very high C-rate of 5C while the pristine sample shows very low discharge capacity (33.4 mAh g⁻¹). CV results shows the significant suppression in the intensity of H2–H3 which indicates the superior electrochemical stability of LaO-0.2 NCM. Thus, we can confirm that La₂O₃ coating is promising technique to achieve superior electrochemical performance in the long term cycling process.