Confinement effects on the glass transition of hydrogen bonded liquids

The glass transition behavior of glycerol and propylene glycol confined in nanoporous glass is investigated using differential scanning calorimetry. Both silanized and unsilanized porous glasses are used to confine the liquids with nominal pore sizes ranging from 2.5 to 7.5 nm, and the glass transition temperature (T(g)) and the limiting fictive temperature (T(f )') are measured on cooling and heating, respectively. The effect of pore fullness is also examined. We find that differences in T(g), DeltaC(p), and the enthalpy overshoot behavior observed on heating are significant between partially and completely filled pores for the case of the unsilanized controlled pore glasses (CPGs) but that the effect of pore fullness is insignificant for the silanized CPGs. In general, the behavior in the silanized CPGs is similar to the behavior in the completely filled unsilanized pores. For glycerol, this includes a small depression in T(f )' on the order of 5 K at 2.5 nm. For propylene glycol, similar behavior is found except that an additional glass transition is observed in both silanized and unsilanized systems approximately 30 K higher than the bulk and a slightly smaller depression on the order of 3 K at 2.5 nm is observed in the completely filled unsilanized pores and in partially and completely filled silanized pores. The results are compared to those in the literature, and the confinement effects are discussed.     

Local structure of a phase-separating binary mixture in a mesoporous glass matrix studied by small-angle neutron scattering

The mesoscopic structure of the binary system isobutyric acid + heavy water (D(2)O) confined in a porous glass (controlled-pore silica glass, mean pore width ca. 10 nm) was studied by small-angle neutron scattering at off-critical compositions in a temperature range above and below the upper critical solution point. The scattering data were analyzed in terms of a structure factor model similar to that proposed by Formisano and Teixeira [Eur. Phys. J. E 1, 1 (2000)], but allowing for both Ornstein-Zernike-type composition fluctuations and domainlike structures in the microphase-separated state of the pore liquid. The results indicate that the phase separation in the pores is shifted by ca. 10 K and spread out in temperature. Microphase separation is pictured as a transition from partial segregation at high temperature, due to the strong preferential adsorption of water at the pore wall, to a tube or capsule configuration of the two phases at low temperatures, depending on the overall composition of the pore liquid. Results for samples in which the composition of the pore liquid can vary with temperature due to equilibration with extra-pore liquid are consistent with this picture.     

2H-solid state NMR and DSC study of isobutyric acid in mesoporous silica materials

Solid state deuterium NMR has been used to study the molecular motion of d(6)-isobutyric acid (d(6)-iBA) in the pure (unconfined) state and confined in the cylindrical pores of two periodic mesoporous silica materials (MCM-41, pore size 3.3 nm and SBA-15, pore size 8 nm), and in a controlled pore glass (CPG-10-75, pore size ca. 10 nm). The line shape analysis of the spectra at different temperatures revealed three rotational states of the iBA molecules: liquid (fast anisotropic reorientation of the molecule), solid I (rotation of the methyl group) and solid II (no rotational motion on the time scale of the experiment). Transition temperatures between these states were determined from the temperature dependence of the fraction of molecules in these states. Whereas the solid I-solid II transition temperature is not affected by confinement, a significant lowering of the liquid-solid I transition temperature in the pores relative to the bulk acid was found for the three matrix materials, exhibiting an unusual dependence on pore size and pore morphology. Complementary DSC measurements on the same systems show that the rotational melting (solid I-liquid) of d(6)-iBA in the pores occurs at a temperature 20-45 K below the thermodynamic melting point. This finding indicated that the decoupling of rotational and translational degrees of freedom in phase transitions in confined systems previously found for benzene is not restricted to molecules with non-specific interactions, but represents a more general phenomenon.     

Temperature dependence of the Landau-Placzek ratio in glass forming liquids

Here, we studied Rayleigh-Brillouin light scattering in ten different glass-forming liquids (α-picoline, toluene, o-toluidine, ethanol, salol, glycerol, dibutyl phthalate, o-terphenyl, propylene carbonate, and propylene glycol). For each of these liquids it was found that the Landau-Placzek ratio is in a good agreement with the theory at high temperatures and significantly exceeds the theoretical prediction below a certain temperature. Transition between the two temperature regimes occurs near T(A), where T(A) is crossover point from an Arrhenius-like to a non-Arrhenius behavior for the α-relaxation time dependence on temperature. Increase of the Landau-Placzek ratio relative to the theoretical prediction below T(A) seems to be the universal feature of glass-formers. We suggest that formation of locally favored structures in liquids below T(A) causes observed excess of the Landau-Placzek ratio.     

Dynamical heterogeneity in glassy o-terphenyl: manifestation of environment changes in photoisomerization kinetics of probe molecules

A new method for the investigation of dynamical heterogeneity in glassy matrixes is presented and illustrated by the example of o-terphenyl (OTP). UV-vis absorption spectroscopy has been used to monitor the cis-trans isomerization kinetics of probe molecules in glassy OTP. The dependence of isomerization quantum yield on light intensity has been established. This dependence is shown to be due to the change in the local environment of the probe molecules. The simple model is suggested to estimate the time required for the environment to change, tauex. The tauex values from 2.6 x 10(2) to 1.9 x 10(5) s have been obtained for environments of molecules of 1-naphthylazomethoxybenzene (NAMB) in OTP over a temperature range from 244 to 204 K (Tg+1 to Tg-39 K). The temperature dependence of exchange time has a non-Arrhenius character. As the temperature decreases, an increase in exchange time slows down. The activation energy of the relaxation process is 54 kJ/mol over the range of 224-239 K.     

Melting and freezing of water in cylindrical silica nanopores

Freezing and melting of H(2)O and D(2)O in the cylindrical pores of well-characterized MCM-41 silica materials (pore diameters from 2.5 to 4.4 nm) was studied by differential scanning calorimetry (DSC) and (1)H NMR cryoporometry. Well-resolved DSC melting and freezing peaks were obtained for pore diameters down to 3.0 nm, but not in 2.5 nm pores. The pore size dependence of the melting point depression DeltaT(m) can be represented by the Gibbs-Thomson equation when the existence of a layer of nonfreezing water at the pore walls is taken into account. The DSC measurements also show that the hysteresis connected with the phase transition, and the melting enthalpy of water in the pores, both vanish near a pore diameter D* approximately equal to 2.8 nm. It is concluded that D* represents a lower limit for first-order melting/freezing in the pores. The NMR spin echo measurements show that a transition from low to high mobility of water molecules takes place in all MCM-41 materials, including the one with 2.5 nm pores, but the transition revealed by NMR occurs at a higher temperature than indicated by the DSC melting peaks. The disagreement between the NMR and DSC transition temperatures becomes more pronounced as the pore size decreases. This is attributed to the fact that with decreasing pore size an increasing fraction of the water molecules is situated in the first and second molecular layers next to the pore wall, and these molecules have slower dynamics than the molecules in the core of the pore.     

On the dielectric susceptibility spectra of supercooled o-terphenyl

Supercooled o-terphenyl has been the subject of many investigations including dielectric relaxation spectroscopy. Due to the low dielectric strength and the tendency to crystallize at elevated temperatures, a detailed shape analysis of the loss profile from the glass transition temperature Tg to approximately 1.2 Tg is not available for the neat glass former. Assessing the origin of the different temperature dependencies of translational and rotational motions in supercooled liquids and its possible connection to heterogeneity requires this knowledge regarding the possible changes in the relaxation-time distribution across the 100 s-100 ns relaxation-time range. This note provides this information for o-terphenyl on the basis of a master curve representation: time-temperature superposition applies with a constant stretching exponent of beta=0.5 in the range of interest.     

Adsorption hysteresis of nitrogen and argon in pore networks and characterization of novel micro- and mesoporous silicas

We report results of nitrogen and argon adsorption experiments performed at 77.4 and 87.3 K on novel micro/mesoporous silica materials with morphologically different networks of mesopores embedded into microporous matrixes: SE3030 silica with worm-like cylindrical channels of mode diameter of approximately 95 angstroms, KLE silica with cage-like spheroidal pores of ca. 140 angstroms, KLE/IL silica with spheroidal pores of approximately 140 angstroms connected by cylindrical channels of approximately 26 angstroms, and, also for a comparison, on Vycor glass with a disordered network of pores of mode diameter of approximately 70 angstroms. We show that the type of hysteresis loop formed by adsorption/desorption isotherms is determined by different mechanisms of condensation and evaporation and depends upon the shape and size of pores. We demonstrate that adsorption experiments performed with different adsorptives allow for detecting and separating the effects of pore blocking/percolation and cavitation in the course of evaporation. The results confirm that cavitation-controlled evaporation occurs in ink-bottle pores with the neck size smaller than a certain critical value. In this case, the pressure of evaporation does not depend upon the neck size. In pores with larger necks, percolation-controlled evaporation occurs, as observed for nitrogen (at 77.4 K) and argon (at 87.3 K) on porous Vycor glass. We elaborate a novel hybrid nonlocal density functional theory (NLDFT) method for calculations of pore size distributions from adsorption isotherms in the entire range of micro- and mesopores. The NLDFT method, applied to the adsorption branch of the isotherm, takes into account the effect of delayed capillary condensation in pores of different geometries. The pore size data obtained by the NLDFT method for SE3030, KLE, and KLE/IL silicas agree with the data of SANS/SAXS techniques.     

Glass Transitions of Ordinary and Heavy Water within Silica‐Gel Nanopores

The dynamic properties of water confined within nanospaces are of interest given that such water plays important roles in geological and biological systems. The enthalpy‐relaxation properties of ordinary and heavy water confined within silica‐gel voids of 1.1, 6, 12, and 52 nm in average diameter were examined by adiabatic calorimetry. Most of the water was found to crystallize within the pores above about 2 nm in diameter but to remain in the liquid state down to 80 K within the pores less than about 1.6 nm in diameter. Only one glass transition was observed, at T_g=119, 124, and 132 K for ordinary water and T_g=125, 130, and 139 K for heavy water, in the 6‐, 12‐, and 52‐nm diameter pores, respectively. On the other hand, two glass transitions were observed at T_g=115 and 160 K for ordinary water and T_g=118 and 165 K for heavy water in the 1.1‐nm pores. Interfacial water molecules on the pore wall, which remain in the noncrystalline state in each case, were interpreted to be responsible for the glass transitions in the region 115–139 K, and internal water molecules, surrounded only by water molecules in the liquid state, are responsible for those at 160 or 165 K in the case of the 1.1‐nm pores. It is suggested that the glass transition of bulk supercooled water takes place potentially at 160 K or above due to the development of an energetically more stable hydrogen‐bonding network of water molecules at low temperatures.     

General and simple approach for control cage and cylindrical mesopores, and thermal/hydrothermal stable frameworks

Highly ordered cage and cylindrical mesoporeous silica monoliths (HOM) with 2- and 3-dimensional (2D and 3D, respectively) structures, mesopore/micropore volumes, and thick-walled frameworks were successfully fabricated by instant direct templating of lyotropic phases of copolymer (EO(m)-PO(n)-EO(m)) surfactants. Large cage-like pores with uniform constriction sizes up to 10 nm and open cylindrical channel-like mesopores can be easily achieved by this simple and efficient synthesis design. Our results show that the cage-like pores could be fabricated at relatively lower copolymer concentrations used in the lyotropic phase domains at copolymer/TMOS ratios of 35 wt %. These ordered cage pore architectures underwent transition to open-cylindrical pores by increasing the copolymer concentration. High EO/PO block copolymers, in general, were crucially affected on the increase of the interior cavity sizes and on the stability of the cage mesopore characters. However, for F108 (EO(141)PO(44)EO(141)) systems, the fabrication of ordered and stable cage pore monoliths was achieved with significantly higher copolymer concentrations up to 90 wt %. Interestingly, the effective copolymer molecular nature was also observed in the ability to design various ordered mesophase geometries in large domain sizes. Our findings here show evidence that the synthetic strategy provides realistic control over a wide range of mesostructured phase geometries and their extended long-range ordering in the final replicas of the silica monolith frameworks. In addition, the HOM silica monoliths exhibited considerable structural stability against higher thermal temperature (up to 1000 degrees C) and longer hydrothermal treatment times under boiling water and steam. The remarkable structural findings of 3D frameworks, transparent monoliths, and micropores combined with large cage- and cylindrical-like mesopores are expected to find promising uses in materials chemistry.     

Modeling of Adsorption in Finite Cylindrical Pores by Means of Density Functional Theory

Adsorption of argon at its boiling point in finite cylindrical pores is considered by means of the non-local density functional theory (NLDFT) with a reference to MCM-41 silica. The NLDFT was adjusted to amorphous solids, which allowed us to quantitatively describe argon adsorption isotherm on nonporous reference silica in the entire bulk pressure range. In contrast to the conventional NLDFT technique, application of the model to cylindrical pores does not show any layering before the phase transition in conformity with experimental data. The finite pore is modeled as a cylindrical cavity bounded from its mouth by an infinite flat surface perpendicular to the pore axis. The adsorption of argon in pores of 4 and 5 nm diameters is analyzed in canonical and grand canonical ensembles using a two-dimensional version of NLDFT, which accounts for the radial and longitudinal fluid density distributions. The simulation results did not show any unusual features associated with accounting for the outer surface and support the conclusions obtained from the classical analysis of capillary condensation and evaporation. That is, the spontaneous condensation occurs at the vapor-like spinodal point, which is the upper limit of mechanical stability of the liquid-like film wetting the pore wall, while the evaporation occurs via a mechanism of receding of the semispherical meniscus from the pore mouth and the complete evaporation of the core occurs at the equilibrium transition pressure. Visualization of the pore filling and empting in the form of contour lines is presented.     

Behavior of acetonitrile confined to mesoporous silica gels as studied by 129Xe NMR: a novel method for determining the pore sizes

129Xe NMR spectra of xenon dissolved in acetonitrile confined into three mesoporous silica gels with nominal pore diameters of 40, 60, and 100 A have been measured over the temperature range 170-245 K. The spectra consist of a number of lines, which contain detailed information on the system. The most interesting result is that the chemical shift of a particular signal observed below the melting point of confined acetonitrile is highly sensitive to the pore size, and hence its shape is sensitive to the pore size distribution function. This signal originates from the xenon atoms sited in very small cavities built up inside the pores during the freezing transition. It can be used to determine the size or even the size distribution function of the pores. In addition, the emergence of this signal reveals the phase transition temperature of acetonitrile inside the pores, which can also be used to determine the size of the pores. The difference in the chemical shifts of two other signals, which arise from xenon dissolved in bulk and confined acetonitrile, provides still another novel method for determining the size of the pores.     

Ultrafast orientational dynamics of nanoconfined benzene

Ultrafast optical Kerr effect spectroscopy has been used to study the orientational dynamics of benzene and benzene-d(6) confined in nanoporous sol-gel glass monoliths with a range of average pore sizes. All of the observed orientational diffusion of confined benzene is found to occur on a slower time scale than in the bulk, even in pores with diameters that are significantly larger than a benzene molecule. The orientational dynamics of benzene-d(6) are found to be inhibited to a lesser extent than those of benzene, which is attributed to the differences in wetting properties of the two liquids on silica. The decays are fit well by a sum of two exponentials, the faster of which depends on pore size. Similar results are found in pores that have been modified with trimethylsilyl groups, although the relaxation is faster than in unmodified pores. Comparison to Raman line width data for confined benzene-d(6) suggests that the liquid exhibits significant structuring at the pore walls, with the benzene molecules lying flat on the surfaces of unmodified pores.     

Water in nanopores. I. Coexistence curves from Gibbs ensemble Monte Carlo simulations

Coexistence curves of water in cylindrical and slitlike nanopores of different size and water-substrate interaction strength were simulated in the Gibbs ensemble. The two-phase coexistence regions cover a wide range of pore filling level and temperature, including ambient temperature. Five different kinds of two-phase coexistence are observed. A single liquid-vapor coexistence is observed in hydrophobic and moderately hydrophilic pores. Surface transitions split from the main liquid-vapor coexistence region, when the water-substrate interaction becomes comparable or stronger than the water-water pair interaction. In this case prewetting, one and two layering transitions were observed. The critical temperature of the first layering transition decreases with strengthening water-substrate interaction towards the critical temperature expected for two-dimensional systems and is not sensitive to the variation of pore size and shape. Liquid-vapor phase transition in a pore with a wall which is already covered with two water layers is most typical for hydrophilic pores. The critical temperature of this transition is very sensitive to the pore size, in contrast to the liquid-vapor critical temperature in hydrophobic pores. The observed rich phase behavior of water in pores evidences that the knowledge of coexistence curves is of crucial importance for the analysis of experimental results and a prerequiste of meaningful simulations.     

多孔介质中甲烷水合物的分解特性

利用定容降压方法测定了在不同多孔介质中甲烷水合物的分解实验数据, 所使用的多孔介质平均孔径分别为9.03, 12.95, 17.96和33.20 nm, 其中孔径为12.95 nm的多孔介质采用了3个粒径范围, 分别为0.105～0.150, 0.150～0.200和0.300～0.450 mm; 其它孔径的多孔介质的粒径范围为0.105～0.150 mm. 在封闭的条件下测定了不同温度与不同初始生成压力下甲烷水合物的分解实验数据(实验温度范围为269.15～278.15 K, 初始生成压力范围为4.1～11.0 MPa), 结果表明, 水合物的分解速度随着初始生成压力的增加和水浴温度的降低而升高, 也随孔径的增加而升高, 但随多孔介质粒径的增大而降低. 在孔径较大和分解温度较低时, 多孔介质中水合物分解引起的温度降低会使水结冰, 从而减缓水合物的分解速度.     

甲烷在中孔分子筛MCM-41中吸附的计算机模拟

采用巨正则系综Monte Carlo方法研究了甲烷在两个不同孔径的MCM-41中不同温度下的吸附等温线和其在孔中的相行为和排列方式.模拟结果显示,在较小孔径的MCM-41中,流体分子达到毛细凝聚所需的化学位较小,并且观察到两个孔径下计算机模拟得到的亚稳态区域都非常宽,使得层状转变（如果有的话）被包含在这个区域.通过比较两种孔径下达到毛细凝聚后的构型,可以看出,在3.5 nm的孔中流体的分子结构出现非常有序的排列,而在5.0 nm的孔中则没有.在常温300 K时甲烷的吸附的计算机模拟表明,孔壁对流体分子的作用仅仅影响较靠近壁面附近的流体分子的排列,而对孔中间的分子几乎没有影响.     

Behavior of a thermotropic nematic liquid crystal confined to controlled pore glasses as studied by 129Xe NMR spectroscopy

The behavior of nematic liquid crystal (LC) Merck Phase 4 confined to controlled pore glass (CPG) materials was investigated using 129Xe nuclear magnetic resonance (NMR) spectroscopy of xenon gas dissolved in the LC. The average pore diameters of the materials varied from 81 to 2917 A, and the measurements were carried out within a wide temperature range (approximately 185-370 K). The spectra contain lots of information about the effect of confinement on the phase of the LC. The theoretical model of shielding of noble gases dissolved in liquid crystals on the basis of pairwise additivity approximation was applied to the analysis of the spectra. When pore diameter is small, smaller than approximately 150 A, xenon experiences on average an isotropic environment inside the pore, and no nematic-isotropic phase transition is observed. When the size is larger than approximately 150 A, nematic phase is observed, and the LC molecules are oriented along pore axis. The orientational order parameter of the LC, S, increases with increasing pore size. In the largest pores, the orientation of the molecules deviates from the pore axis direction to magnetic field direction, which implies that the size of the pores (approximately 3000 A) is close to magnetic coherence length. The decrease of magnetic coherence length with increasing temperature is clearly seen from the spectra. When the sample is cooled rapidly by immersing it in liquid nitrogen, xenon atoms do not squeeze out from the solid, as they do during gradual freezing, but they are occluded inside the solid lattice, and their chemical shift is very sensitive to crystal structure. This makes it possible to study the effect of confinement on the solid phases. According to the measured 129Xe NMR spectra, possibly three different solid phases are observed from bulk liquid crystal in the used temperature region. The same is also seen from the samples containing larger pores (pore size larger than approximately 500 A), and the solid-solid phase-transition temperatures are the same. However, no first-order solid-solid phase transitions are observed from the smaller pores. Melting point depression, that is, the depression of solid-nematic transition temperature observed from the pores as compared with that in bulk LC, is seen to be very sensitive to the pore size, and it can be used for the determination of pore size of an unknown material.     

Large Scale Porous Structure in Gels and Relationship with Their Plastic Behavior

Silica gels (classical aerogels and composite aerogels) have been prepared by classical gelation and addition of silica soot in the gelifying solution before gelation. Due to the aggregation mechanisms, these structures are characterized by a fractal organization. The fractal network previously described in the literature (1–100 nm) which results from the aggregation mechanism of the organosiloxane is affected by the addition of the silica soots. Ultra Small Angle X-ray Scattering (USAXS) experiments (done at ESRF) shows that besides the fractal network built by the organosiloxane, the silica soots are forming another porous structure at a higher scale.The mechanical properties seem to be dependent on this large pore structure. Under isostatic pressure, aerogels display an irreversible shrinkage caused by plastic deformation. As a consequence of this plastic shrinkage it is possible to densify, by the pore collapse tending towards the silica glass. The densification mechanism is different from the one obtained by a sintering at high temperature. The pore collapse mechanism is favored by the large pores structure of the composite aerogels, in contrast to viscous sintering.     

Hydraulic and surface characteristics of membranes with parallel cylindrical pores

Pore size distributions and pore densities of track-etched polycarbonate ultrafiltration (UF) membranes with pore sizes ranging from 10 to 100 nm (0.01–0.10 μm) were characterized by image analysis of field emission scanning electron micrographs (FESEM) of membranes. Porosity data obtained from image analysis compared well with those derived from manufacturer's specifications, but this may have been coincidental, as pore size and pore density results differed by 20–40% and 25–70%, respectively. The experimentally determined flux through each membrane type varied by up to 30–45% within a batch, and were about 8–46 times higher than the theoretical over the range of membranes. The disparity between theoretical and experimental flux was beyond the bounds of physical variability of the membranes. The membranes with smaller pore size tended to show a greater disparity. Water flux of all membranes increased with increasing temperature, generally in accord with the decreasing viscosity of water. However, unlike the linear increase for the membranes with larger pores (> 50 nm), the membranes with smaller pores (10 and 30 nm) showed exponential increase with temperature. Water flux also increased with a pressure increase from 50 to 300 kPa. Raised pressure appear to enlarge pores resulting in exponential flux enhancement at higher pressure, particularly for membranes with smaller pores (PC10). The pores may have stretched open under pressure to deliver the higher than expected fluxes due to flexibility of polycarbonate films, although FESEM showed no visible evidence of fracturing or tearing of the membranes. The flux results from filtration of aqueous protein solution were a little lower and correlated well with water permeability of the membranes, but remained in discord with the pore size distribution results.     

Resistive-pulse detection of multilamellar liposomes

The resistive-pulse method was used to monitor the pressure-driven translocation of multilamellar liposomes with radii between 190 and 450 nm through a single conical nanopore embedded in a glass membrane. Liposomes (0% and 5% 1,2-dioleoyl-sn-glycero-3-phospho-l-serine (sodium salt) in 1,2-dilauroyl-sn-glycero-3-phosphocholine or 0%, 5%, and 9% 1,2-dipalmitoyl-sn-glycero-3-phospho(1'-rac-glycerol) (sodium salt) in 1,2-dipalmitoyl-sn-glycero-3-phosphocholine) were prepared by extrusion through a polycarbonate membrane. Liposome translocation through a glass nanopore was studied as a function of nanopore size and the temperature relative to the lipid bilayer transition temperature, T(c). All translocation events through pores larger than the liposome, regardless of temperature, show translocation times between 30 and 300 μs and current pulse heights between 0.2% and 15% from the open pore baseline. However, liposomes at temperatures below the T(c) were captured at the pore orifice when translocation was attempted through pores of smaller dimensions, but squeezed through the same pores when the temperature was raised above T(c). The results provide insights into the deformation and translocation of individual liposomes through a porous material.