温度敏感性水凝胶合成反应及性能研究

<正> 水凝胶是一种能显著地溶胀于水但在水中并不能溶解的亲水性聚合物凝胶。水凝胶的性质不仅与聚合单体和交联剂的性质以及聚合工艺条件有关,而且还取决于溶胀时的条件,如溶胀温度和溶胀介质的pH值等。有一些水凝胶随着溶胀温度升高到某一温度以上时会发生从溶胀的软的透明状态到消溶胀的硬的不透明状态的变化,在这一温度附近的溶胀比变化往往可达几倍到几十倍。如果将溶胀温度降到这一温度以下时,凝胶状     

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征;N-异丙基丙烯酰胺;水凝胶;温敏性;快速响应     

Synthesis and characterization of thermo-sensitive poly (N-isopropylacrylamide) hydrogel with fast response rate

Thermo-sensitive poly (N-isopropylacrylamide) (PNIPA) hydrogel with fast response rate was prepared by polymerizing N-isopropylacrylamide (NIPA) in an aqueous hydroxyl-propyl-methyl cellulose solution. The volume phase transition temperature of PNIPA hydrogels was characterized by differential scanning calorimetry (DSC), and the surface morphology was observed by scanning electron microscopy (SEM). The swelling ratios of the hydrogels at different temperatures were measured. Furthermore, the deswelling kinetics of the hydrogels was also studied by measuring their water retention capacity. In comparison with a conventional PNIPA hydrogel prepared in water, the hydrogel synthesized in aqueous hydroxyl-propyl-methyl cellulose solution has higher swelling ratios at temperatures below the lower critical solution temperature and exhibits a much faster response rate to temperature changes. For example, the hydrogel made in aqueous hydroxyl-propyl-methyl cellulose solution lost 89% water within 1 min and about 93% water in 4 min, whereas the conventional hydrogel lost only about 66% water in 15 min from the deswelling measurement in similar conditions. Translated from Chinese Journal of Applied Chemistry, 2006, 23(6): 581–585 (in Chinese)     

Preparation and separation function of N‐isopropylacrylamide copolymer hydrogels

In this paper, N‐isopropylacrylamide (NIPA) was synthesized by acrylonitrile and isopropanol. Poly(N‐isopropylacrylamide) (PNIPA) was prepared by a chemical method. The dependence of its swelling behavior on temperature was studied. Results showed that PNIPA hydrogel was a temperature‐sensitive gel. Its LCST (lower critical solution temperature) was about 32 °C, and its swelling ratio (at 20 °C) was about 17–18. Sodium acrylate (SA) and sodium methylacrylate (SMA) were copolymerized with NIPA respectively. Equilibrium swelling ratios of the copolymer hydrogels at lower temperature were two to three times that of PNIPA. The LCST of the copolymer hydrogels could be controlled between 32 and 45 °C by adjusting the content of SA or SMA. Kinetics of P(NIPA‐co‐SA) hydrogels, whether swelling or shrinking processes, were in good agreement with apparent second order kinetic equations. Several experiments were designed to separate aqueous bovine serum albumin solution using the hydrogels prepared above. The separation efficiency was about 80%. Copyright © 2000 John Wiley & Sons, Ltd.     

APPLICATION OF SURFACE GRAFTED POLY N-ISOPROPYL ACRYLAMIDE BY RADIATION TECHNOLOGY FOR PROTEIN SOLUTION CONCENTRATION

Poly N-isopropyl acrylamide (abbreviated as PNIPA) as a kind of thermally sensitive hydrogel is utilized to concentrate Bovin Serum Albumin (BSA) solution. In order to decrease its surface adsorption to BSA in aqueous solution, surface layer grafting of the gels by radiation technology was carried out. The results showed that hydroxyl propyl methacrylate (HPMA) grained gel exhibited a low level of BSA adsorption and still kept the original thermally sensitive properties of PNIPA hydrogels.     

温敏凝胶体积相转变温度的压敏性

温敏凝胶体积相转变温度的压敏性钟兴，王宇新，王世昌（天津大学化学工程研究所，天津，３０００７２）金曼蓉（天津第二医学院药学系，天津，３００２０３）关键词Ｎ－烷基丙烯酰胺凝胶、体积相转变、温度敏感性、压力敏感性环境敏感性凝胶（交联聚合物）在生化分离、固...     

Thermoresponsive poly(N-isopropylacrylamide) nanogels/poly(acrylamide) nanostructured hydrogels

Here we report the preparation and characterization of nanostructured thermo-responsive poly(acrylamide) (PAM)-based hydrogels. The addition of slightly crosslinked poly(N-isopropylacrylamide) (PNIPA) nanogels to AM reactive aqueous solution produces nanostructured hydrogels that exhibit a volume phase transition temperature (T_VPT). Their swelling kinetics, T_VPT's and mechanical properties at the equilibrium-swollen state (H_eq) are investigated as a function of the concentration of PNIPA nanogels in the nanostructured hydrogels. Nanostructured hydrogels with PNIPA nanogels/AM mass ratios of 20/80 and above exhibit higher H_eq and longer time to reach the equilibrium swelling than those of the conventional PAM hydrogels. However, the PNIPA nanogels possess thermo-responsive character missing in conventional PAM hydrogels. The T_VPT of nanostructured hydrogels depends on PNIPA nanogel content but their elastic and Young moduli are larger than those of conventional hydrogels at similar swelling ratios. Swelling kinetics, T_VPT, and mechanical properties are explained in terms of the controlled in-homogeneities introduced by the PNIPA nanogels during the polymerization.     

Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

羧甲基纤维素钠/聚(N-异丙基丙烯酰胺)纳米复合水凝胶的制备及结构性能表征

以无机粘土为交联剂制备了具有温度、pH双重敏感特性的羧甲基纤维素钠/聚(N-异丙基丙烯酰胺)/粘土半互穿网络纳米复合水凝胶(CMC/PNIPA/Clay semi-IPN),并通过红外和透射电镜对其结构和形态进行了表征。在酸性(pH=1.2)和20℃条件下,分别研究了温度和不同pH缓冲液对该凝胶溶胀度的影响,测定了复合水凝胶的力学性能。结果表明:水凝胶中的粘土被剥离成单片层,且均匀分散在凝胶网络中,起交联剂的作用,而CMC以线性大分子的形态存在;CMC/PNIPA/Clay具有良好的温度、pH双重敏感特性;凝胶的断裂伸长率>1 000%。     

Temperature‐Sensitive Poly(N‐isopropylacrylamide) Hydrogels with Macroporous Structure and Fast Response Rate

Macroporous temperature‐sensitive poly(N‐isopropylacrylamide) (PNIPA) hydrogels were prepared by a novel phase‐separation technique to improve the response properties. In comparison with a conventional PNIPA hydrogel prepared in water, these macroporous hydrogels, prepared by polymerization in aqueous sucrose solutions, have higher swelling ratios at temperatures below the lower critical solution temperature and exhibit much faster response rates to temperature changes.

Scanning electron microscopy image of the surface of a PNIPA hydrogel, prepared in 1.50 M aqueous sucrose solution.     

Poly(vinyl alcohol)/poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) semi-interpenetrating polymer network hydrogels with rapid response to temperature changes

A series of thermosensitive and fast-response poly(vinyl alcohol) (PVA)/poly(N-isopropylacrylamide) (PNIPA) hydrogels were prepared by incorporating PVA into cross-linked PNIPA to form a semi-interpenetrating polymeric network (semi-IPN). Compared to the conventional PNIPA hydrogel, the semi-IPN hydrogels thus prepared exhibit significantly faster response rates and undergo full deswelling in 1 min (lose about 95% water within 1 min) when the temperature is raised above their lower critical solution temperature, and have larger equilibrium swelling ratios at room temperature. These improved properties are attributed to the incorporation of PVA, which forms water-releasing channels and results in increased hydrophilicity, into the PNIPA hydrogel networks.     

腐植酸钠/聚N-异丙基丙烯酰胺/粘土杂化水凝胶的合成及脱色性能

以N-异丙基丙烯酰胺单体、粘土和腐植酸钠为原料合成了温敏腐植酸钠/聚N-异丙基丙烯酰胺/粘土（SH/PNIPA/clay）系列水凝胶。用红外光谱分析仪对其内部相互作用进行了研究,并用紫外可见分光光度计对水凝胶吸附-解吸亚甲基蓝的性能进行了测试。实验结果表明凝胶中SH与PNIPA形成了氢键;凝胶对亚甲基蓝（MB）的吸附和解吸能力受腐植酸钠的含量、粘土含量、亚甲基蓝的起始浓度和温度的影响。２％粘土含量和低温条件有利于凝胶吸附和解吸。     

Thermoresponsive polymeric nanoparticles stabilized by surfactants

Solutions of poly(N-isopropylacrylamide) (PNIPA) with ionic and nonionic surfactants were investigated by light scattering methods at temperatures 15–45 °C. In contrast to previous studies, where surfactants were used in excess, lower concentrations of surfactants were used. The formation of well-defined nanoparticles of PNIPA was observed on heating above the lower critical solution temperature. The effect of PNIPA and surfactant concentrations, and molecular weight of PNIPA on nanoparticle parameters and on the phase transition temperature of PNIPA solutions were investigated. An interpretation based on stabilization of PNIPA nuclei by surfactants was suggested.     

聚乙烯醇水凝胶溶胀特性研究

在前文对聚乙烯醇水溶液冰冻凝胶化浓度依赖性研究基础上，对接触浓度（Ｃ）以上聚乙烯醇水溶液通过冰冻－融化处理，制得了一种含水率高达９５～９８％的水凝胶．系统研究了该水凝胶在蒸馏水中的溶胀及溶解特性．得到了一个与实验结果相吻合的溶胀动力学方程：Ｑ１＝Ｑｅ－（Ｑｅ－ＱＯ）／ｅｋｔ，及平衡溶胀比Ｑｅ与浓度之间的定量关系：Ｑｅ＝６０．３－４．４５×１０２Ｃ．发现当冰冻－融化次数Ｎ≤５时，平衡溶胀比Ｑｅ及溶解量Ｗ与冰冻－融化次数（Ｎ）间满足幂函数关系：Ｑｅ。Ｗ通过对聚乙烯醇水凝胶平衡溶胀比与经冰冻处理的聚乙烯醇水溶液特性粘数进行比较，发现反映链间氢键凝聚缠结效应与反映链内氢键凝聚缠结效应的定量指标具有等效性．     

疏水改性智能水凝胶P(NIPA-co-DiAB)的合成及其温敏行为

以N-异丙基丙烯酰胺(NIPA)和N,N-双烯丙基苄胺(DiAB)为共聚单体、N,N-亚甲基双丙烯酰胺(BIS)为交联剂、十二烷基硫酸钠(SDS)为表面活性剂、过硫酸铵(APS)-四甲基乙二胺(TMEDA)为氧化还原引发体系,采用自由胶束交联共聚法合成了疏水基团为芳香基的疏水改性温敏性智能水凝胶P(NIPA-co-DiAB)。研究了DiAB摩尔分数(x(DiAB))对水凝胶溶胀性能的影响。 在初始溶胀阶段,随着x(DiAB)由0增大至3%,P(NIPA-co-DiAB)水凝胶的溶胀行为由Fickian扩散转变为non-Fickian扩散。x(DiAB)分别为0、1%、2%和3%时,P(NIPA-co-DiAB)水凝胶的平衡溶胀率SR0在蒸馏水中分别为63.6、93.5、141.6和167.4,在0.01 mol/L SDS溶液中分别为63.1、71.0、59.0和77.5,在CTAB溶液中分别为37.6、42.2、44.1和60.0,在Triton X-100溶液中分别为30.9、49.4、68.5和88.3。 结果表明,P(NIPA-co-DiAB)水凝胶的(SR0)大于PNIPA水凝胶,且在蒸馏中比在0.01 mol/L表面活性剂溶液中要大。 加入0.01 mol/L Triton X-100、CTAB或SDS后,PNIPA水凝胶的体积相变温度或较低临界溶解温度(LCST)由32.5 ℃分别增加至35.4、45.6和80 ℃。P(NIPA-co-DiAB)水凝胶的LCST由32.0～32.5 ℃分别增加至34.7～35.6 ℃、45.8~46.2 ℃和80 ℃。 加入表面活性剂能增加P(NIPA-co-DiAB)水凝胶的体积相变温度,高的体积相变温度与DiAB含量无关。     

Preparation and characterization of sodium carboxymethylcellulose/poly(N-isopropylacrylamide)/clay semi-IPN nanocomposite hydrogels

A new kind of pH-/temperature-responsive semi-interpenetrating polymer network hydrogels based on linear sodium carboxymethylcellulose (CMC) and poly(N-isopropylacrylamide) (PNIPA) cross-linked by inorganic clay (CMC/PNIPA/Clay hydrogel) was prepared. The temperature- and pH-responsive behaviors, the mechanical properties of these hydrogels were investigated. The CMC/PNIPA/Clay hydrogels exhibited a volume phase transition temperature around 32 °C with no significant deviation from the conventional PNIPA hydrogels. The swelling ratio of the CMC/PNIPA/Clay hydrogels gradually decreased with increasing the contents of clay. The influence of pH value on swelling behaviors showed that there is a maximum swelling ratio at pH 5.9. Moreover, the CMC/PNIPA/Clay hydrogels exhibited excellent mechanical properties with high tensile stress and elongation at break in excess of 1200%.     

聚N-异丙基丙烯酰胺/类水滑石复合水凝胶的制备及温敏性

以类水滑石(LDHs)和N-异丙基丙烯酰胺(NIPA)为原材料,采用自由基引发聚合制得了有机无机PNIPA/LDHs温度敏感复合水凝胶。 通过热重分析仪(TGA)、示差扫描量热仪(DSC)和扫描电子显微镜(SEM)等技术手段表征了材料的结构和性能。 结果表明,PNIPA/LDHs复合水凝胶在33 ℃左右可实现溶胶-凝胶的可逆性变化,LDHs质量分数基本不影响复合水凝胶的胶凝化温度和胶凝时间。 LDHs添加可使PNIPA/LDHs复合水凝胶的热稳定性较NIPA有大幅度提升。 随LDHs质量分数及n(Mg):n(Al)的增加,复合凝胶的吸热峰值稍有增加。 所合成PNIPA/LDHs复合水凝胶表面粗糙不平,具有一定的孔洞结构。     

Novel Interpenetrating Networks (IPNs) Hydrogels Prepared In Situ by Liquid-Phase Photopolymerization

Novel interpenetrating networks (IPNs) hydrogels responsive to temperature were prepared in situ by liquid-phase photopolymerization. The first network of the IPNs (poly isopropyl acrylamide) were formed with a special kind of hectorite (Laponite XLS) modified by tetrasodium pyrophosphate as cross-linker and 2-oxogultaric acid as photoinitiator. The samples were subsequently immersed in an acrylamide (AAm) aqueous solution for at least one day for preparing IPNs hydrogels, in which acrylamide aqueous solution containing N,N′-Dimetyl acrylamide (MBAA) as cross-linker and 2-oxogultaric acid as photoinitiator. Then the second networks were in situ formed by introducing ultraviolet light irradiated PNIPAAm gels. The swelling/deswelling behaviors of IPNs hydrogels were measured. Compared with the corresponding nanocomposite PNIPAAm hydroges(NC hydrogels), chemically cross-linked PNIPAAm and PAAm IPNs hydrogels, the results indicate that the new IPN hydrogel has a faster deswelling rate above its LCST (≈32 °C). The effect was explained as being an additional contribution of the PAAm chains in IPN hydrogels, which may act as a water-releasing channel when the hydrophobic aggregation of PNIPA takes place.     

温度及pH敏感聚(丙烯酸)/聚(N-异丙基丙烯酰胺)互穿聚合物网络水凝胶的合成及性能研究

合成聚（丙烯酸）／聚（Ｎ 异丙基丙烯酰胺）互穿聚合物网络（ＰＡＡｃ／ＰＮＩＰＡＩＰＮ）水凝胶，具有温度及ｐＨ双重敏感特性．这种水凝胶在弱碱性条件下的溶胀率远大于酸性条件下的溶胀率．在酸性条件下，随着温度上升，凝胶的溶胀率也随之逐渐上升；而在弱碱性条件下，温度低于聚（Ｎ 异丙基丙烯酰胺）（ＰＮＩＰＡ）的较低临界溶解温度（ＬＣＳＴ）时，溶胀率也随着温度的上升而上升，当温度达到ＬＣＳＴ时，凝胶的溶胀率突然急剧下降，并随着温度的逐渐上升而下降．     

温度及pH敏感性共聚物水凝胶的合成及其对辅酶A的控制释放

以N-乙烯基吡咯烷酮(NVP)和甲基丙烯酸-N,N-二甲胺乙酯(DMAEMA)为单体,采用自由基聚合法合成了NVP与DMAEMA的共聚物及其水凝胶。研究发现共聚物的水溶液具有温度及pH双重敏感特性。相分离温度随DMAEMA含量的增加和水溶液浓度的降低而升高,随pH值的增大而减小且相变敏锐。通过对水凝胶溶胀率的考察,发现共聚凝胶在适当的单体浓度及交联剂浓度下,有较敏感的溶胀-退胀行为。在碱性条件下,共聚凝胶随温度的升高迅速退胀。pH=9时,改变温度,对辅酶A有很好的控制释放;而在酸性条件下,则无退胀行为,对辅酶A不能释放。