Polycaprolactone–poly(ethylene glycol) block copolymer,I: synthesis and degradability in vitro

A new type of biodegradable polymer material, poly(caprolactone)–poly(ethylene glycol) block copolymer (PCL-b-PEG), was synthesized by means of direct copolycondensation of ε-caprolactone with poly(ethylene glycol) in the presence of a Ti(OBu)₄ catalyst. The degradability of the polycaprolactone was improved by introducing a PEG component into it. The degradation of PCL-b-PEG copolymer increase with a decreasing crystallinity of the copolymer, and can be controlled by adjusting the component ratio of the copolymer.     

SYNTHESIS OF POLY(ETHYLENE TEREPHTHALATE)-POLYCAPROLACTONE BLOCK COPOLYMER BY DIRECT COPOLYMERIZATION*

Poly(ethylene terephthalate) -polycaprolactone block copolymer (PCL- b-PET) is a polyester withimproved biodegradability. In the present paper, a new direct copolymerization method of ε-caprolactone (ε-CL) and bishydroxyethylene terephthalate (BHET) in the presence of Ti(OBu)_4 was proposed for thesynthesis of PCL-b-PET. The PCL-b-PET copolymer was characterized by IR, GPC and ~1H-NMRtechniques, and the effects of synthesis conditions, such as temperature, reaction time and concentration ofcatalyst on the copolymerization were discussed.     

Effect of Processing Parameters on the Optical Properties of TiO<Subscript>2</Subscript>/Ormosil Planar Waveguide

Hybrid TiO₂/ormosil waveguiding films have been prepared by the sol-gel method at low thermal treatment temperature of 150C. The influence of processing parameters including the molar ratios of titanium butoxide (Ti(OBu)₄)/3-glycidoxypropyltrimethoxysilane (GLYMO) and H₂O/Ti(OBu)₄ (expressed as R), especially aging of sol on the optical properties was investigated. The optical properties of films were measured with scanning electron microscope (SEM), UV/VIS/NIR spectrophotometer (UV-Vis), m-line and the scattering-detection method. The results indicate that the film thickness increases with the increase of sol aging time, but the variation of refractive index as a function of sol aging time depends on the relative ratios of GLYMO to Ti(OBu)₄. Higher transmittance and lower attenuation of the planar waveguide can be obtained in the sol with lower Ti(OBu)₄ contents and shorter aging time.     

Mechanical,aging, optical and rheological properties of toughening polylactide by melt blending with poly(ethylene glycol) based copolymers

Two novel biodegradable copolymers, including poly(ethylene glycol)-succinate copolymer (PES) and poly(ethylene glycol)-succinate-l-lactide copolymer (PESL), have been successfully synthesized via melt polycondensation using SnCl₂ as a catalyst. The copolymers were used to toughen PLA by melt blending. The DSC and SEM results indicated that the two copolymers were compatible well with PLA, and the compatibility of PESL was superior to that of PES. The results of tensile testing showed that the extensibility of PLA was largely improved by blending with PES or PESL. At same blending ratios, the elongation at break of PLA/PESL blends was far higher than that of PLA/PES ones. The elongation maintained stable through aging for 3 months. The moisture absorption of the blends enhanced due to the strong moisture absorption of PEG segments in PES or PESL molecules, which did not directly lead to enhance the hydrolytic degradation rate of the PLA. The PLA blends containing 20–30 wt% PES or PESL were high transparent materials with high light scattering. The toughening PLA materials could potentially be used as a soft biodegradable packaging material or a special optical material.     

Oligotrimerization of hexamethylene diisocyanate by organometallic catalysts

The oligotrimerization of hexamethylene diisocyanate by tributylin oxide (TBTO), Zr(OBu)₄, Ti(OBu)₄ and Pb-naphthenate was studied. For mild reaction conditions, i.e. weak catalyst (TBTO), low catalyst concentration and temperature, the reaction gave selectively the cyclic trimer (I) and not higher oligomers.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Novel Complex Catalyst of η3‐(Pentamethylcyclopentadienyl)dimethylaluminum/Titanium(IV) Butoxide (Cp*AlMe2/Ti(OBu)4) for Syndiotactic Polystyrene

A novel metallocene catalyst was prepared from the reaction of (η³‐pentamethylcyclopentadienyl)dimethylaluminum (Cp*AlMe₂) and titanium(IV) n‐butoxide Ti(OBu)₄. The resulting titanocene Cp*Ti(OBu)₃ was combined with methylaluminoxane (MAO)/tri‐iso‐butylaluminum (TIBA) to carry out the syndiotactic polymerization of styrene. The resulting syndiotactic polystyrene (sPS) possesses high syndiotacticity according to ¹³C NMR. Catalytic activity and the molecular weight of the resulting sPSs were discussed in terms of reaction temperature, concentration of MAO, amounts of scavenger TIBA added, and the hydrogen pressure applied during polymerization.     

The influence of core-shell structured modifiers on the toughness of poly (vinyl chloride)

The core-shell structured grafted copolymer particles of polybutadiene grafted polymethyl methacrylate (PB-g-PMMA, MB) were prepared by emulsion polymerization. The MB particles were used to modify poly (vinyl chloride) (PVC) by melt blending. The mechanical properties of the PVC blends were investigated. The micro-morphology of the PVC blends was observed by scanning electron microscopy (SEM). The results indicated that the samples with the best impact strength could be obtained when the core-shell weight ratio of PB to PMMA is lower than 93:7, the mechanical properties correlated well with SEM morphologies, the addition of modifier with the ratio core to shell of 93:7 could reduce the domain size of the dispersed phase. Furthermore, the compatibility and properties of the blends were greatly enhanced and improved. The modifier particles could be well dispersed in the PVC matrix.     

Synthesis and biodegradation studies of 1,3-propanediol based aliphatic poly(ester carbonate)s

A series of poly(ester carbonate)s were obtained from adipic acid, 1,3-propanediol and diethyl carbonate in the presence of catalyst Ti(OBu)₄ by polycondensation and transestrification process. The amount of monomeric composition was varied in order to get the polymer of different composition. The structure, average molecular weight and physical properties of poly(ester carbonate) were characterized by FT-IR, ¹H NMR, solubility, solution viscosity, gel permeation chromatography, differential scanning calorimetry and XRD analysis. Biodegradability of poly(ester carbonate)s was investigated by hydrolytic (pH 7.2 and 11.5), enzymatic using Rhizopus delemar lipase at 37 °C and soil burial test. The biodegradation rate observed was more for poly(ester carbonate) containing 40% and 10% of diethyl carbonate due to their low crystallinity.     

Oxidation of Stereo‐regular Poly(styrene‐co‐4‐methylstyrene) by Cobalt(II) Acetate Tetrahydrate/Sodium Bromide Catalyst

Chemical modification on the stereo‐regular poly(styrene‐co‐4‐methylstyrene) (sPS‐PMS) was attempted in this study. Metallocene copolymerization of styrene (St) and 4‐methylstyrene (MSt) was performed by using η⁵‐pentamethylcyclopentadienyl‐titanium(IV)tributoxide (Cp*Ti(OBu)₃)/methylaluminoxane (MAO)/tri‐iso‐butylaluminum (TIBA) catalyst in the bulk state. Cobalt(II) catalyst was then applied to oxidize the benzylic methyl group on the MSt units of the resulting sPS‐PMS copolymer. Both aldehyde and carboxylic acid in the oxidized products were resolved by the FTIR and ¹H NMR. The oxidized sPS‐PMSs exhibit a low and a high‐temperature T_g and T_m corresponding to the transitions in the amorphous and the crystalline regions. Hydrogen‐bond and polar interactions between the aldehyde and carboxylic acids tend to interrupt the regular chain packing of the oxidized sPS‐PMS, resulting in the lowering of T_m with oxidation level. The oxidized sPS‐PMS showed better adhesion to glass fiber than pure sPS‐PMS copolymer as evaluated from the respective SEM fractured micrographs.     

New approach on the development of plasticized polylactide (PLA): Grafting of poly(ethylene glycol) (PEG) via reactive extrusion

In this work, new ways of plasticizing polylactide (PLA) with low molecular poly(ethylene glycol) (PEG) were developed to improve the ductility of PLA while maintaining the plasticizer content at maximum 20 wt.% PLA. To this end, a reactive blending of anhydride-grafted PLA (MAG-PLA) copolymer with PEG, with chains terminated with hydroxyl groups, was performed. During the melt-processing, a fraction of PEG was grafted into the anhydride-functionalized PLA chains. The role of the grafted fraction was to improve the compatibility between PLA and PEG. Reactive extrusion and melt-blending of neat and modified PLA with PEG did not induce any dramatic drop of PLA molecular weight. The in situ reactive grafting of PEG into the modified PLA in PLA/PEG blends showed a clear effect on the thermal properties of PLA. It was demonstrated by DSC that the mobility gained by PLA chains in the plasticized blends yielded crystallization. The grafting of a fraction of PEG into PLA did not affect this process. However, DSC results obtained after the second heating showed an interesting effect on the T_g when 20 wt.% PEG were melt blended with neat PLA or 10 wt.% MAG-PLA. In the latter case, the T_g displayed by the reactive blend was shifted to even lower temperatures at around 14 °C, while the T_g of neat PLA and PLA blended with 20 wt.% PEG was around 60 and 23 °C, respectively. Regarding viscoelastic and viscoplastic properties, the presence of MAG-PLA does not significantly influence the behavior of plasticized PLA. Indeed, with or without MAG-PLA, elastic modulus and yield stress decrease, while ultimate strain increases with the addition of PEG into PLA.     

Miscibility and properties of poly(l-lactic acid)/poly(butylene terephthalate) blends

Binary blends of poly(l-lactide) (PLLA) and poly(butylene terephthalate) (PBT) containing PLLA as major component were prepared by melt mixing. The two polymers are immiscible, but display compatibility, probably due to the establishment of interactions between the functional groups of the two polyesters upon melt mixing. Electron microscopy analysis revealed that in the blends containing up to 20% of poly(butylene terephthalate), PBT particles are finely dispersed within the PLLA matrix, with a good adhesion between the phases. The PLLA/PBT 60/40 blend presents a co-continuous multi-level morphology, where PLLA domains, containing dispersed PBT units, are embedded in a PBT matrix. The varied morphology affects the mechanical properties of the material, as the 60/40 blend displays a largely enhanced resistance to elongation, compared to the blends with lower PBT content.     

生物基超韧聚乳酸复合材料的制备与性能

采用来源于可再生资源的聚醚酰胺弹性体（PEBA）增韧聚乳酸（PLA）制备超韧聚乳酸（PLA/PEBA-GMA）复合材料.为了提高PEBA与PLA之间的相容性,选择极性单体甲基丙烯酸缩水甘油酯（GMA）、共接枝单体乙烯基吡咯烷酮（NVP）及引发剂过氧化二异丙苯（DCP）对PEBA进行接枝改性制备PEBA-GMA.研究了接枝单体组分的用量（m/g）对PLA/PEBA-GMA复合材料性能的影响.研究发现,随着接枝单体组分用量的提高,复合材料的缺口冲击强度逐渐增大,当接枝单体组分GMA,NVP和DCP的用量分别为2.5,2.5和0.25 g时,复合材料的冲击强度高达88.6 kJ/m²,断裂伸长率为164.1%.研究表明,在熔融共混过程中,聚乳酸的端基（—OH和—COOH）与PEBA-GMA上环氧基团发生反应,有效改善两相间的界面相容性,随着接枝单体组分比例的提高,分散相PEBA-GMA的粒子尺寸逐渐减小且分布均匀.     

Thermal degradation during melt processing of poly(ethylene oxide), poly(vinylidenefluoride-co-hexafluoropropylene) and their blends in the presence of additives, for conducting applications

In this paper, the thermal degradation during compounding of poly(ethylene oxide) and poly(vinylidenefluoride-co-hexafluoropropylene) and their immiscible blends was investigated. Infrared spectroscopy, size exclusion chromatography, dynamic rheology, thermogravimetric analysis, and coupled gas chromatography-mass spectroscopy were used. Most of the identified degradation products or substances are glycols, formates, lactones, ethers or even acids for long processing times. The mechanisms for the production of these chemical compounds were already reported in previous publications. Additionally, the influence of carbon black and LiV₃O₈ additives, currently used for enhancing the conductive properties, was studied. Addition of carbon black causes an increase in the PEO stability, whereas addition of LiV₃O₈ has an opposite and dramatic effect. PVDF-HFP is found to be less susceptible to degradation because of the inherent stability of fluorine-containing polymers. However, melt processing provides additional contributions to degradation because of the high viscosities.     

Effects of polystyrene‐b‐poly(ethylene/propylene)‐b‐polystyrene compatibilizer on the recycled polypropylene and recycled high‐impact polystyrene blends

The recycled polypropylene/recycled high‐impact polystyrene (R‐PP/R‐HIPS) blends were melt extruded by twin‐screw extruder and produced by injection molding machine. The effects of polystyrene‐b‐poly(ethylene/propylene)‐b‐polystyrene copolymer (SEPS) used as compatibilizer on the mechanical properties, morphology, melt flow index, equilibrium torque, and glass transition temperature (T_g) of the blends were investigated. It was found that the notch impact strength and the elongation at break of the R‐PP/R‐HIPS blends with the addition of 10 wt% SEPS were 6.46 kJ/m² and 31.96%, which were significantly improved by 162.46% and 57.06%, respectively, than that of the uncompatibilized blends. Moreover, the addition of SEPS had a negligible effect on the tensile strength of the R‐PP/R‐HIPS blends. Additionally, the morphology of the blends demonstrated improved distribution and decreased size of the dispersed R‐HIPS phase with increasing the SEPS content. The increase of the melt flow index and the equilibrium torque indicated that the viscosity of the blends increased when the SEPS was incorporated into the R‐PP/R‐HIPS blends. The dynamic mechanical properties test showed that when the content of SEPS was 10 wt%, the difference of T_g decreased from 91.72°C to 81.51°C. The results obtained by differential scanning calorimetry were similar to those measured by dynamic mechanical properties, indicating an improved compatibility of the blends with the addition of SEPS.     

Influence of the transesterification catalyst structure on the reactive compatibilization and properties of poly(ethylene terephthalate) (PET)/dibutyl succinate functionalized poly(ethylene) blends

The transesterification between poly(ethylene terephthalate) (PET) and dibutyl succinate functionalized polyethylene (POF) was studied by preparing blends in a discontinuous mixer in the presence of different Zn and Ti catalysts. In particular the catalytic activities of Zn(OOCCH₃)₂, Ti(OBu)₄, ZnO and TiO(OCCH₃)₂ were compared. The mechanism of reactions occurring in the melt was studied both by a model compounds approach and by characterizing the macromolecular products of the melt processing by means of selective extractions, infrared analysis and the determinations of the molecular weight of PET. The results are discussed in terms of electrophilicity and nucleophilicity of the different catalysts. The catalysts structure also affected the phase distribution. In fact from a morphologic point of view in PET matrix blends the use of zinc derivatives yielded preferentially dispersed-like phase distribution, while the use of titanium derivatives resulted in partially co-continuous phase morphology. The stability of the attained phase distribution was also monitored during compression moulding and it evolved rapidly in fully dispersed phase morphology. The tensile properties of compression moulded films revealed that the occurred reactions and morphological assessment induced a general decrease of tensile modulus and an increase of elongation at break.     

Effect of ethylene-co-vinyl acetate-glycidylmethacrylate and cellulose microfibers on the thermal,rheological and biodegradation properties of poly(lactic acid) based systems

The properties and biodegradation behavior of blends of poly(lactic acid) (PLA) and ethylene-vinyl acetate-glycidylmethacrylate copolymer (EVA-GMA), and their composites with cellulose microfibers (CF) were investigated. The blends and composites were obtained by melt mixing and the morphology, phase behavior, thermal and rheological properties of PLA/EVA-GMA blends and PLA/EVA-GMA/CF composite films were investigated as a function of the composition. The disintegrability in composting conditions was examined by means of morphological, thermal and chemical analyses to gain insights into the post-use degradation processes. The results indicated a good compatibility of the two polymers in the blends with copolymer content up to 30 wt.%, while at higher EVA-GMA content a phase separation was observed. In the composites, the presence of EVA-GMA contributes to improve the interfacial adhesion between cellulose fibers and PLA, due to interactions of the epoxy groups of GMA with hydroxyls of CF. The addition of cellulose microfibers in PLA/EVA-GMA system modifies the rheological behavior, since complex viscosity increased in presence of fibers and decreased with an increase in frequency. Disintegration tests showed that the addition of EVA-GMA influence the PLA disintegration process, and after 21 days in composting conditions, blends and composites showed faster degradation rate in comparison with neat PLA due to the different morphologies induced by the presence of EVA-GMA and CF phases able to allow a faster water diffusion and an efficient PLA degradation process.     

Miscibility and enzymatic degradation studies of poly(ε-caprolactone)/poly(propylene succinate) blends

In the present study the miscibility behaviour and the biodegradability of poly(ε-caprolactone)/poly(propylene succinate) (PCL/PPSu) blends were investigated. Both of these aliphatic polyesters were laboratory synthesized. For the polymer characterization DSC, ¹H NMR, WAXD and molecular weight measurements were performed. Blends of the polymers with compositions 90/10, 80/20, 70/30 and 60/40 w/w were prepared by solution-casting. DSC analysis of the prepared blends indicated only a very limited miscibility in the melt phase since the polymer-polymer interaction parameter χ₁₂ was −0.11. In the case of crystallized specimens two distinct phases existed in all studied compositions as it was found by SEM micrographs and the particle size distribution of PPSu dispersed phase increased with increasing PPSu content. Enzymatic hydrolysis for several days of the prepared blends was performed using Rhizopus delemar lipase at pH 7.2 and 30 °C. SEM micrographs of thin film surfaces revealed that hydrolysis affected mainly the PPSu polymer as well as the amorphous phase of PCL. For all polymer blends an increase of the melting temperatures and the heat of fusions was recorded after the hydrolysis. The biodegradation rates as expressed in terms of weight loss were faster for the blends with higher PPSu content. Finally, a simple theoretical kinetic model was developed to describe the enzymatic hydrolysis of the blends and the Michaelis-Menten parameters were estimated.     

Synthesis and hydrolytic degradation of poly(ethylene succinate) and poly(ethylene terephthalate) copolymers

The conditions of synthesis of statistical poly(ethylene succinate-co-terephthalate) copolymers (2GTS) and high molecular weight poly(ethylene succinate) (PES) with good hydrolytic and optical parameters, designed for the production of biodegradable products and resins, are presented in this article. Copolymers were prepared by melt polycondensation of bis-(β-hydroxyethylene terephthalate) (BHET) and succinic acid (SA) with excess of ethylene glycol (2G) in the presence of a novel titanium/silicate catalyst (C-94) and catalytic grade of germanium dioxide (GeO₂) as cocatalyst. The chemical structure and physical properties of those materials were characterized by ¹H NMR, FT-IR, dynamical-mechanical thermal analyses (DMTA), differential scanning calorimetry (DSC), solution viscosity and spectroscopic methods. The hydrolytic degradation was performed in a water solution with variable pH, also in garden soil and in compost. The highest hydrolytic degradation rate was observed for pH 4 and for compost. Better hydrolytic degradation values in compost medium were observed for copolyester prepared in the presence of GeO₂ as polycondensation cocatalyst. The copolyester with 40 mol% of aliphatic units was chosen for industrial syntheses which were performed in ELANA and subsequently the processing parameters and compatibility with potato starch of this polyester were checked by BIOP Biopolymer Technologies AG.     

Diglycidyl ether of bisphenol-A epoxy resin–polyether sulfone/polyether sulfone ether ketone blends: phase morphology, fracture toughness and thermo-mechanical properties

The properties of diglycidyl ether of bisphenol-A epoxy resin toughened with poly(ether sulfone ether ketone) (PESEK) and poly(ether sulfone) (PES) polymers were investigated. PESEK was synthesised by the nucleophilic substitution reaction of 4,4’-difluorobenzophenone with dihydroxydiphenylsulfone using sulfolane as solvent and potassium carbonate as catalyst at 230 °C. The T _g–composition behaviour of the homogeneous epoxy resin/PESEK blend was modelled using Fox, Gordon–Taylor and Kelley–Bueche equations. A single relaxation near the glass transition of epoxy resin was observed in all the blend systems. From dynamic mechanical analysis, the crosslink density of the blends was found to decrease with increase in the thermoplastic concentration. The storage modulus of the epoxy/PESEK blends was lower than that of neat resin, whilst it is higher for epoxy/PES blends up to glass transition temperature, thereafter it decreases. Scanning electron microscopic studies of the blends revealed a homogeneous morphology. The homogeneity of the blends was attributed to the similarity in chemical structure of the modifier and the cured epoxy network and due to the H-bonding interactions between the blend components. The fracture toughness of epoxy resin increased on blending with PESEK and PES. The increase in fracture toughness was due to the increase in ductility of the matrix. The thermal stability of the blends was comparable to that of neat epoxy resin.