The impact of chemical composition on the degradation kinetics of poly(lactic-co-glycolic) acid copolymers cast films in phosphate buffer solution

We have investigated the in vitro degradation of poly(lactic-co-glycolic) acid copolymer with different lactic to glycolic ratio: 50:50, 65:35, 75:25, 95:05 and 100:00 (mol. %). The degradation studies were performed on solvent cast films of controlled thickness and shape. The samples were incubated at 37 °C in phosphate buffered saline solution. The degradation was followed using potentiometry, light microscopy, gravimetry, size exclusion chromatography and differential scanning calorimetry. The same degradation process, as discussed in detail in our previous article for PLGA 50:50 (E. Vey et al., J. of Polym. Deg. and Stab. 2008, 93, 1896-1876), was observed for all the samples investigated, however the time scale over which the different events/degradation steps were observed increased with increasing lactic content of the polymer. The glass transition temperatures of the films increase with lactic content and are thought to have a significant impact on the rate of diffusion of water into the films - the higher the glass transition the slower the diffusion of water - and therefore on the degradation dynamics of the films. Kinetic parameters were extracted from the acid release, molecular weight and mass loss data. In each case linear correlations between the rate constants extracted and the lactic content of the polymer were found. The overall degradation rate of the films was found to decrease with increasing lactic content.     

Thermal Properties of Copoly(L‐lactic acid/glycolic acid) by Direct Melt Polycondensation

Poly(L‐lactic acid‐co‐glycolic acid) (PLGA) was prepared from hydroxy‐acids with melt polymerization. In this way, the copoly(L‐LA/GA) (PLGA) was synthesized directly using a binary catalyst (tin chloride dihydrate/p‐toluenesulfonic acid). The thermal properties of PLGA were studied by differential scanning calorimetry (DSC) and nuclear magnetic resonance (NMR). The results show that the melting point of PLGA decreases with increasing mole fraction of GA units in the copolymer. In addition, the melting point of polymer also decreases with increasing degree of racemization of the polymer.     

The effect of glycolic acid monomer ratio on the emulsifying activity of PLGA in preparation of protein-loaded SLN

Our previous work demonstrated that lactic/glycolic acid copolymer (PLGA) was an efficient emulsifier for the primary w/o emulsion in the formulation of protein-loaded solid lipid nanoparticles (SLN) by w/o/w double emulsion-solvent evaporation technique. In this work, the effect of PLGA composition on the emulsifying activity was studied with PLGA of different lactic/glycolic acid ratios (90/10, 75/25, 50/50). The results demonstrated that the glycolic acid monomer ratio significantly affected the emulsifying activity of PLGA. Increasing the glycolic acid monomer ratio from 10% to 50% decreased the minimum PLGA content needed to produce stable w/o emulsions. With same PLGA contents, increase of the glycolic acid monomer ratio increased the stable time of the w/o emulsion, yielded smaller and narrower-distributed SLN, and enhanced the encapsulation efficiency and loading capacity.     

One‐step synthesis of poly(lactic‐co‐glycolic acid)‐g‐poly‐1‐vinylpyrrolidin‐2‐one copolymers

The radical polymerization of 1‐vinylpyrrolidin‐2‐one (NVP) in poly(lactic‐co‐glycolic acid) (PLGA) 50:50 at 100 °C leads to amphiphilic PLGA‐g‐PVP copolymers. Their composition is determined by FT‐IR spectroscopy. Thermogravimetric analyses agree with FT‐IR determinations. Saponification of the PLGA‐g‐PVP polyester portion allows isolating the PVP side chains and measuring their molecular weight, from which the average chain transfer constant (C_T) of the PLGA units is estimated. The MALDI‐TOF spectra of PVP reveal the presence at one chain end of residues of either glycolic acid‐ or lactic acid‐ or lactic/glycolic acid dimers, trimers and one tetramer, the other terminal being hydrogen. This unequivocally demonstrates that grafting occurred. Accordingly, the orthogonal solvent pair ethyl acetate—methanol, while separating the components of PLGA/PVP intimate mixtures, fails to separate pure PVP or PLGA from the reaction products. All PLGA‐g‐PVP and PLGA/PLGA‐g‐PVP blends, but not PLGA/PVP blends, give long‐time stable dispersions in water. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1919–1928     

Degradation mechanism of poly(lactic-co-glycolic) acid block copolymer cast films in phosphate buffer solution

We have investigated the degradation of poly(lactic-co-glycolic) acid copolymer with a lactic to glycolic ratio of 50:50. Solvent-cast films were incubated at 37 °C in phosphate buffered saline solution and their degradation was followed using potentiometry, light microscopy, gravimetry, size exclusion chromatography, differential scanning calorimetry and infrared spectroscopy. The degradation process was found to have two main steps. The first step was observed from 0 to 7 days of degradation. During the first few days a soft layer formed at the surface of the film. As degradation time increased this soft surface layer was found to swell and wrinkle. The polymer molecular weight in the bulk was found to decrease as soon as the film was placed in the medium while the polymer present in the surface layer was found to degrade at a much slower rate. The second step of degradation was found to occur after 8 days. At this stage of the degradation process the molecular weight of the polymer in the bulk of the films was so low that the materials became liquid resulting in the detachment of the film from the glass slide. At this stage the mass loss and amount of acid released in the media were found to increase significantly.     

Role of hydrolytic degradation of polylactide drug carriers in developing micro- and nanoscale polylactide-based drug dosage forms

The present analytical survey explores different aspects of hydrolytic degradation of drug dosage forms (DF) based on polylactides, homopolymers of lactic acid (PLA) and copolymers of lactic and glycolic acids (PLGA). The study includes various scientific data from multiple sources describing the effect of the PLGA nanocarrier hydrolytic degradation rate on the profile of drug release from the DFs intended for intravenous and intramuscular administration, including micro- and nanoparticles, and implants. The following aspects are explored in the review: design of experiments aimed at studying the hydrolytic degradation kinetics of PLGA carriers; commonly employed analytical methods; interpretation of the mechanism of PLGA-based DF hydrolytic degradation; factors that influence the hydrolytic degradation rate of PLGA drug carriers as part of DFs; interrelation between the processes of polymer carrier hydrolytic degradation and drug substance release from the PLGA-based DFs.

     

Novel method to characterize the hydrolytic decomposition of biopolymer surfaces

Present pharmaceutical research is focused on the development, modification and characterisation of new drug delivery systems. Among the many different substances, biodegradable polymers and copolymers are of practical importance, especially if their degradation byproducts are non-toxic. The polymeric drug carriers are not easily wettable by water or aqueous solutions, i.e. they are hydrophobic. This surface hydrophobicity is unfavourable for keeping drug carriers circulating in the blood long enough to release the drug so that it reaches its target. Therefore, copolymers with components of different hydrophobicity were introduced, to make them less hydrophobic and hence more suitable for drug delivery in the human body. Exploratory experiments with one homopolymer, , -poly(lactic acid), , -PLA and two of its copolymers, , -poly(lactic/glycolic acid), and , -PLGA with 85/15 and 50/50 copolymer ratios were carried out. Films of these substances were prepared by dip coating onto hydrophobic and hydrophilic substrates. The changes in wettability of the polymer layers, caused by the direct contact with an aqueous environment (soaking the samples in distilled water), have been studied to model the hydrolytic decomposition of polymer surfaces and to follow the changes in their wettability by dynamic contact angle measurements in a non-destructive manner. It was found that each polymer film became less hydrophobic (dynamic contact angles decreased) and more heterogeneous as the decomposition progressed with time. Increasingly significant decreases in contact angles were observed for the copolymer films containing 15 and 50% glycolic acid, during the 50–80-day-long study. These findings were supported by gel chromatographic analysis of the soaking liquids. It was concluded that the homopolymer layer of , -PLA was the most resistant to hydrolysis and the stability of copolymer films decreased with increasing glycolic acid ratio in the copolymers. This is accordance with the fact that the less crystalline poly(glycolic acid) is more hydrophilic and hence less resistant to hydrolytic decomposition, than the poly(lactic acid). The effect of pH on the rate of hydrolysis of polymer films was also established; the influence of pH on the decomposition was best demonstrated, again, for the copolymer with 50/50 component ratio. The outcome of these experiments showed that the contact angle measuring method enables us to detect, follow and interpret the hydrolytic decomposition of biopolymer substances in a non-invasive manner.     

New approaches to mapping through-thickness variations in the degradation in poly (lactide-co-glycolide)

Biodegradable poly (lactide-co-glycolide) (PLGA) copolymers have been used for many years for biomedical applications such as soluble sutures, orthopaedic implants and more recently as potential tissue scaffold materials. The rate at which the copolymers degrade can be manipulated from a period of days to months by changing the lactide/glycolic acid ratio. Degradation of PLGA copolymers occurs by hydrolysis of the ester bonds in the polymer backbone. The hydrolysis reaction is autocatalytic and is accelerated by the build up of degradation products in the bulk of the material. As a consequence, material degradation is expected to be non-uniform through the specimen thickness with the material at the centre degrading at a faster rate than at the surface. Despite many studies of PLGA degradation, information on this local variance is sparse as the techniques used to track the process are usually bulk measures. In this study, two new approaches for monitoring degradation have been developed that enable local measurements of degradation to be made throughout the specimen over an extended period of time. Chemical and mechanical variations in the structure of the polymer have been mapped using attenuated total reflectance infrared spectroscopy (ATR-FTIR) and nanoindentation. These have produced comparable results and show that the degradation rate at the centre of the specimens is almost an order of magnitude higher than at the surface.     

Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

Raman spectroelectrochemical study on the kinetics of electrochemical degradation of polyaniline

The kinetics of electrochemical degradation of polyaniline and a copolymer of aniline and metanilic acid have been studied by in situ Raman spectroscopy at a gold electrode. It has been concluded that probably no drastic changes in polymer structure occur on prolonged electrochemical treatment of polymer films at a high electrode potential (0.8 V vs. Ag/AgCl). Instead, most prominent changes relate to a gradual decrease of an overall intensity of spectra, viz. to gradual degradation of a polymer layer. The degradation proceeds faster at pH 1.0, compared to pH 7.0. The kinetic results obtained have been analyzed following simple 2- or 3-parameter exponential decay equations, and compared with the known degradation rate constants.     

Synthesis and NMR Characterization of Multi‐hydroxyl End‐groups PEG and PLGA‐PEG Barbell‐like Copolymers

Multi‐hydroxyl end‐groups poly(ethylene glycol) (PEG) was prepared from PEG and epichlorohydrin. Then, PEG‐supported poly(lactic‐ran‐glycolic acid) (PLGA)_n‐PEG‐(PLGA)_n (n=1, 2, 4) linear‐dendritic barbell‐like copolymers were synthesized through direct polycondensation under bulk condition from the multi‐hydroxyl end‐groups PEG, lactic acid and glycolic acid. Arm numbers were varied, with 2, 4 and 8, by using bis‐, tetra‐, and octa‐hydroxyl end‐groups PEG, respectively. The chemical structures, absolute number‐average molecular weight, the monomer units per single arm and the molar ratio of hydroxyl acid monomer units of the (PLGA)_n‐PEG‐(PLGA)_n barbell‐like copolymers were analyzed by NMR spectroscopy. The result indicated that the structures of the multi‐hydroxyl end‐groups PEG and (PLGA)_n‐PEG‐(PLGA)_n barbell‐like copolymers were consistent with design. Compared with the theoretical values, molecular weights determined by ¹H‐NMR end‐group analysis gave reasonably consistent values, but the values determined by gel permeation chromatography (GPC) were considerably less than theoretical values. The results indicated that (PLGA)_n‐PEG‐(PLGA)_n copolymers have linear‐dendritic structures.     

Synthesis and Characterization of Amphiphilic Biodegradable Copolymer,Poly(aspartic acid‐co‐lactic acid)

An amphiphilic biodegradable polymer, poly(aspartic acid‐co‐lactic acid) (PAL), was synthesized by simply heating a mixture of aspartic acid (Asp) and L ‐lactide without additional catalysts or solvents. The unique branched architecture comprising succinimide units and lactic acid units was confirmed by IR and NMR spectroscopy. A copolymer of sodium aspartate and lactic acid (PALNa) was prepared by reacting PAL with an aqueous sodium hydroxide solution. The PAL was soluble in many organic solvents, while the PALNa was soluble in methanol and water. The hydrolytic degradation behavior of PAL varied with the copolymer composition. A higher Asp content resulted in a faster molecular weight decrease, and introducing glycolic acid units accelerated the degradation rate.

Microphotograph of microsphere of PAL‐1/5.     

Surface Stabilization of Diblock PEG‐PLGA Micelles by Polymerization of N‐Vinyl‐2‐pyrrolidone

This paper presents a new approach to improving the physical stability of biodegradable poly‐(ethylene glycol)‐block‐poly[(DL ‐lactic acid)‐co‐(glycolic acid)] (PEG‐PLGA) micelles. A hydroxyl‐terminated PEG monomethacrylate (PEGmer) macroinitiator was used to prepare a methacrylate‐end‐capped PEG‐PLGA diblock copolymer by the ring‐opening polymerization of D ,L ‐lactide and glycolide. The surface‐exposed methacrylate groups in the shell layer of the micelles can be polymerized with N‐vinyl‐2‐pyrrolidone. The resulting micelles show substantially enhanced stability.     

Effect of PLGA block molecular weight on gelling temperature of PLGA‐PEG‐PLGA thermoresponsive copolymers

Thermoresponsive, biodegradable polymeric hydrogel networks are used widely in medicinal applications. Poly(d ,l ‐lactic acid‐co‐glycolic acid)‐b‐poly(ethylene glycol)‐b‐poly(d ,l ‐lactic acid‐co‐glycolic acid) (PLGA‐PEG‐PLGA) triblock copolymers exhibit a sol–gel transition upon heating. The effect of PLGA block and PEG chain molecular weights (MWs) on the gelling temperature of polymer aqueous solution (20% w/w) is described. All polymer solutions convert into a hard gel within 2 °C of the gelling temperature. The release properties of the gels were displayed using paracetamol as a representative drug. A linear relation is described between the gelling temperature and PLGA block MW. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 35–39     

Characterization and enzymatic degradation of microbial copolyester P(3HB-co-3HV)s produced by metabolic reaction model-based system

The two types of poly(3-hydroxybutyrate-co-3-hydroxyvalerate)s [P(3HB-co-3HV)s] were produced by Paracoccus denitrificans ATCC 17741 using two different feeding methods. The produced P(3HB-co-3HV)s were fractionated and the copolymer sequence distributions were analyzed by ¹H and ¹³C NMR spectroscopy. It was found that the P(3HB-co-3HV) samples produced by conventional feeding method were statistically random copolymers. The sequence distributions of P(3HB-co-3HV) samples produced by optimization method were different from random P(3HB-co-3HV)s. The thermal properties and melting behaviors were analyzed by differential scanning calorimetry (DSC). These results demonstrated that P(3HB-co-3HV) samples produced by optimization method are close in nature to P(3HB-co-3HV)s rich in long-sequence of block 3HB units, but less in 3HV random regions. The enzymatic degradation profile of P(3HB-co-3HV) films was investigated in the presence of 3-hydroxybutyrate depolymerase from Pseudomonase lemoignei. The degradation process was observed by monitoring the time-dependent change in the weight loss of copolymer films. The surface erosion of copolymer films was qualitatively monitored by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The highest degradation rate of 2.6% per day was observed for random P(3HB-co-38%3HV) produced by conventional method. In comparison, the hydrolysis degradation rates of random P(3HB-co-3HV)s were about one time faster than those of P(3HB-co-3HV)s produced by optimization method.     

In Vitro Degradation of Poly(lactic-co2-glycolic) Acid Random Copolymers

We have investigated the in vitro degradation of poly(lactic-co-glycolic) acid copolymer with a lactic to glycolic ratio of 65/35. The degradation studies were performed on solvent-cast films of controlled thickness and shape. The samples were then incubated at 37 °C in phosphate buffered saline solution. The degradation was followed using potentiometry, light microscopy, gravimetry, gel permeation chromatography and differential scanning calorimetry. Water was found to diffuse inside the film as soon as the sample was placed in the degradation media. Wrinkles formed on the upper layer while degradation took place via chain scission in the bulk of the film. After 10 days, this led to the creation of a vesicle where liquid low molecular weight oligomers were trapped inside a thin film of high molecular weight polymer. This thin film acted as a membrane allowing only low molecular weight compounds to diffuse out of the film.     

Novel Thermoreversible Gelation of Biodegradable PLGA‐block‐PEO‐block‐PLGA Triblock Copolymers in Aqueous Solution

The BAB‐type triblock copolymers composed of a central poly(ethylene oxide) (PEO, M̄_nPEO = 1 000) block and two poly[(D ,L ‐lactic acid)‐co‐(glycolic acid)] end blocks with molecular weights between 900 and 1 600 exhibited an interesting phase transition behavior. The copolymer aqueous solution can form micelles with PLGA loops in the core and a PEO shell and groups of micelles because of bridging between micelles caused by the PLGA blocks with raising temperature. A possible micellar gelation mechanism was suggested.     

In vitro degradation of porous poly(dl-lactide-co-glycolide) (PLGA)/bioactive glass composite foams with a polar structure

In vitro degradation of porous 50/50, 70/30 and 90/10 PLGA (poly(dl-lactide-co-glycolide)) foams and PLGA/bioactive glass (20 wt%) composite foams was studied up to 16 weeks in TRIS (pH 7.4; 37 °C). Polar PLGA/bioactive glass composite films were prepared by applying the bioactive glass (S53P4) on one side of the composite. Porous foams were made by solvent casting and pressure quenching with CO₂. The fabricated foams had an initial pore size of 50-500 μm and thickness of 2-2.5 mm. In vitro degradation of the prepared foams was evaluated after 1, 2, 4, 6, 8, 12 and 16 weeks. Weight loss, water uptake, molecular mass and the amount of dissolved bioactive glass were measured after each time period. Changes in pore morphology were analysed with SEM. The present in vitro results will be evaluated and compared with the results from ongoing animal studies where comparable implants are used for bone defect treatment under non-load-bearing conditions.     

Prediction of microclimate pH in poly(lactic-co-glycolic acid) films

An equilibrium mathematical model that accurately predicts microclimate pH (mupH) in thin biodegradable polymer films of poly(lactic-co-glycolic acid) (PLGA) is described. mupH kinetics was shown to be primarily a function of: (i) kinetics of water-soluble acid content and composition in the polymer matrix and (ii) polymer/water partition coefficient of water-soluble degradation products (P(i)). Polymers were coated on standard pH glass electrodes, and mupH was measured potentiometrically. Water-soluble acid distribution and content in PLGA films were determined by pre-derivatization HPLC. Polymer degradation products partitioned favorably in the polymer phase relative to water (P(i) range: approximately 6-100), and P(i) increased with increasing hydrophobicity of the acidic species according to a linear free energy law related to reversed phase HPLC retention time for the corresponding derivatized bromophenacyl esters. The mupH predicted by the model was in excellent agreement with experimental mupH for several PLGAs as a function of time and PLGA lactic/glycolic acid ratio. These data may be useful to slowly release pH-sensitive PLGA-encapsulated bioactive substances and provide a general framework for predicting partitioning behavior of degradation products in biodegradable polymers.     

XPS and wettability characterization of modified poly(lactic acid) and poly(lactic/glycolic acid) films

Poly(lactic acid) (PLA) and poly(lactic/glycolic acid) copolymers (PLGA) are biodegradable drug carriers of great importance, although successful pharmaceutical application requires adjustment of the surface properties of the polymeric drug delivery system to be compatible with the biological environment. For that reason, reduction of the original hydrophobicity of the PLA or PLGA surfaces was performed by applying a hydrophilic polymer poly(ethylene oxide) (PEO) with the aim to improve biocompatibility of the original polymer. PEO-containing surfaces were prepared by incorporation of block copolymeric surfactants, poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (Pluronic), into the hydrophobic surface. Films of polymer blends from PLA or PLGA (with lactic/glycolic acid ratios of 75/25 and 50/50) and from Pluronics (PE6800, PE6400, and PE6100) were obtained by the solvent casting method, applying the Pluronics at different concentrations between 1 and 9.1% w/w. Wettability was measured to monitor the change in surface hydrophobicity, while X-ray photoelectron spectroscopy (XPS) was applied to determine the composition and chemical structure of the polymer surface and its change with surface modification. Substantial reduction of surface hydrophobicity was achieved on both the PLA homopolymer and the PLGA copolymers by applying the Pluronics at various concentrations. In accordance with the wettability changes the accumulation of Pluronics in the surface layer was greatly affected by the initial hydrophobicity of the polymer, namely, by the lactide content of the copolymer. The extent of surface modification was also found to be dependent on the type of blended Pluronics. Surface activity of the modifying Pluronic component was interpreted by using the solubility parameters.