Effect of fire retardant on flammability of acrylamide and 2-acrylamido-2-methylpropane sodium sulfonate copolymer composites

Poly[acrylamide-co-(2-acrylamido-2-methylpropane sodium sulfonate)] superabsorbents and superabsorbent composites (SAPCs) with zinc borate and/or melamine as fire retardants were synthesized. Water absorbencies decreased inversely to added amount of fire retardant. Thermal stability of SAPC/zinc borate increases with increasing zinc borate. Incorporating melamine improved thermal stability of the SAPC until 300 °C. Flammability analysis demonstrated that wood surface coated with SAP or SAPC emulsions extended time to ignition of the wood. Peak heat release rate and total heat release are smallest in specimens coated with SAPC/30% melamine. Wood coated with SAPC incorporating 20% zinc borate/10% melamine mixture gave the longest time to ignition at 4½ min.     

Dynamic and equilibrium swelling of a sulfonic acid superabsorbent copolymer in salt solutions

Superabsorbent copolymers were synthesized by free radical reverse emulsion from the monomers acrylamide and 2‐acrylamido‐2‐methyl‐propanosulfonic acid with a divinyl crosslinker (methylene‐bisacrylamide). The copolymer synthesized was then identified by Fourier transform infrared spectroscopy, its porosity was examined by electronic microscopy, and its specific gravity was determined by the conventional procedure. The dynamic and equilibrium swelling behavior of the copolymer was studied, in water and in salt solutions, at 25 °C (chlorides and sulfates of sodium and magnesium). As to the equilibrium swelling, the influence of the pH as well as of the salt type and its concentration was observed. As to the dynamic swelling, it was interpreted in terms of both a simple power of time equation, and a more detailed model based on a coupled diffusion‐relaxation mechanism. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 505–514, 2004     

Application of Crosslinked Acrylamidoxime/2-Acrylamido-2-methylpropane Sulfonic Acid Copolymer in Wastewater Treatment

Crosslinked acrylonitrile/acrylamidoxime/2-acrylamido-2-methylpropane sulfonic acid (AN/AAx/AMPS) based hydrogels was prepared by radical solution polymerization technique. The structures of hydrogels were characterized by FTIR analysis and the results were consistent with the expected structures. These hydrogels were used for the separation of Cd(II), Cu(II), and Fe(III) ions from their aqueous solutions. The influence of the uptake conditions such as pH, time, and initial feed concentration on the metal ion binding capacity of hydrogel was also tested. The selectivity of the hydrogel toward the different metal ions tested was Cd(II)>Fe(III)>Cu(II). The recovery of metal ions was also investigated in acid media.     

Development of highly ionic conductive cellulose acetate-g-poly (2-acrylamido-2-methylpropane sulfonic acid-co-methyl methacrylate) graft copolymer membranes

A novel cellulose acetate-g-poly (2-acrylamido-2-methylpropane sulfonic acid-co- methyl methacrylate) copolymer was prepared via free radical polymerization for the first time. The chemical structure of the graft copolymer was confirmed using FT-IR, ¹H NMR and EDX. The TGA and DSC investigated the thermal changes. Factors affecting the grafting process were studied and various grafting characteristic parameters such as grafting efficiency (%), grafting yield (%) and add-on value (%) were determined. Flexible membranes based on different graft copolymer compositions were fabricated by simple solution casting. Physicochemical properties including ion exchange capability (IEC), water uptake (WU) and proton conductivity (σ) were evaluated. These membranes demonstrated higher IEC, WU and conductivity than the pristine CA. The maximum proton conductivity of the CA-g-poly (2-acrylamido-2-methylpropane sulfonic acid-co- methyl methacrylate) copolymer membrane (68%; Add-on %) was found to be 6.44 × 10⁻³ S/cm compared with 0.035 × 10⁻³ S/cm of the pristine CA. Thus, the appropriate graft copolymer composition will allow fine-tuning of the physical characteristics and led to several potential applications, such as polyelectrolyte fuel cells membranes or biodiesel production.     

丙烯酸/2-丙烯酰胺基-2-甲基丙磺酸高吸水树脂的反相悬浮聚合及其性能

采用反相悬浮聚合法,通过均匀实验设计,制备了聚(丙烯酸(AA)/2-丙烯酰胺基-2-甲基丙磺酸(AMPS)）(PAAMPS)高吸水树脂,探讨了单体摩尔分数及其中和度、引发剂及交联剂摩尔分数（相对于单体总量）对蒸馏水、质量分数0.9%NaCl水溶液中吸液性能的影响,并经实验数据拟合,得到了二次回归方程,比较了优化配方、单因素实验的模拟值和实验值,结果表明,模拟值与优化值基本接近,其优化工艺参数为：AMPS占单体的摩尔分数8%,中和度为75%,交联剂、引发剂用量与单体的摩尔分数分别为0.035%和0.17%,单体总质量浓度为30%,分散剂用量为单体质量分数的0.5%,反应温度70 ℃,反应时间1.5 h。 此条件下合成的PAAMPS在蒸馏水、0.9%NaCl水溶液中的吸液倍率分别为1.600和130 g/g。     

Synthesis of cross-linked carboxymethyl cellulose and poly (2-acrylamido-2-methylpropane sulfonic acid) hydrogel for sustained drug release optimized by Box-Behnken Design

This research aims to fabricate and characterize chemically crosslinked CMC/PVP-co-poly (AMPS) based hydrogel for the sustained release of model drug metoprolol tartrate through the free radical polymerization technique. Box-Behnken Design was used to optimize CMC/PVP-co-poly (AMPS) hydrogel by varying the content of reactants such as; polymers (CMC and PVP), monomer (AMPS), and crosslinker (EGDMA). Carboxymethyl cellulose (CMC) was crosslinked chemically with AMPS with a constant ratio of PVP by the ethylene glycol dimethacrylate as the crosslinker in the presence of sodium hydrogen sulfite (SHS)/ammonium peroxodisulfate (APS) as initiators. After developing CMC-based hydrogels using different polymers, monomer, and crosslinker concentrations, this study encompassed dynamic swelling, sol–gel fraction, drug release and chemical characterizations such as FTIR, XRD, TGA, DSC, and SEM. In vitro drug release and swelling were performed at 1.2 and 6.8 pH to determine the sustained release pattern and pH-responsive behavior. These parameters depended on the crosslinker, polymer, and monomer ratios used in the formulation development. XRD, SEM, and FTIR showed the successful grafting of constituents resulting in the formation of a stable hydrogel. DSC and TGA confirmed the thermodynamic stability of the hydrogel. Hydrogel swelling was increased with an increase in the ratio of monomer; however, an increase in the ratio of polymer and crosslinker decreased the hydrogel swelling. In vitro gel fraction and drug release also depended on polymer, monomer, and crosslinker ratios. The fabricated CMC/PVP-co-poly (AMPS) hydrogels constituted a potential system for sustained drug delivery.     

十二烷基苯磺酸钠-硫酸耐而蓝体系的共振瑞利散射光谱及其分析应用

提出了共振瑞利散射法(RRS)测定十二烷基苯磺酸钠(SDBS)的新方法。在pH为1.98～3.29的B-R缓冲溶液中,硫酸耐而蓝与SDBS结合生成离子缔合物,使溶液共振瑞利散射(RRS)增强,其最大散射峰位于760 nm,另在533 nm、400 nm有两个较弱的散射峰。SDBS的浓度在0.04～1.6 mg/L范围内,与RRS强度有良好的线性关系,对SDBS的检出限(3σ)达0.018 mg/L。研究了适宜的反应条件和影响因素,表明该方法灵敏、稳定。用于环境水样中阴离子表面活性剂含量的测定,回收率为95.9%～106.7%。     

Non-Gaussian elasticity of swollen poly(N-isopropylacrylamide) gels at high charge densities

Modulus of elasticity of highly charged N-isopropylacrylamide (NIPA) based hydrogels (PNIPA) are measured at various swelling degrees in water. The sodium salt of 2-acrylamido-2-methylpropane sulfonic acid (AMPS) was used as the ionic comonomer of NIPA in the hydrogel preparation. The mole fraction of AMPS in the comonomer feed was varied between 0 and 1, while the crosslinker ratio was fixed at 1/85. The elasticity data show that the equilibrium swollen PNIPA hydrogels are in the non-Gaussian regime. Equations were derived based on the inverse Langevin function for the swelling ratio and the modulus of highly charged PNIPA hydrogels and checked by experiments. Results of calculations show good agreement to the swelling and elasticity data of highly swollen PNIPA gels.     

Electrochemical study on oxidation of ofloxacin at nano-ZnS/poly (Styrene sulfonic acid sodium salt) modified electrode and its interaction with calf thymus DNA

A PSS/nano-ZnS thin film modified electrode has been fabricated on the surface of glassy carbon electrode (GCE). In pH 5.0 phosphate buffer solution (PBS), Ofloxacin (OFX) appeared as an anodic peak with the peak potential of 1.28 V at PSS/nano-ZnS film modified electrode. In comparison with a bare GCE or a nano-ZnS modified electrode, the PSS/nano-ZnS film modified electrode exhibited an enhanced effectiveness for the oxidation of OFX. Cyclic voltammetry (CV) coupled with fluorescence and UV-vis absorbance spectra techniques were used to study the interaction of OFX with Calf thymus DNA (ctDNA). The interaction of OFX and ctDNA could result in a considerable decrease in the peak currents and positively shift in the peak potential, as well as changes of fluorescence, UV-Vis adsorption spectra. All acquired data showed that the new adduct between OFX and ctDNA was formed. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 3, pp. 289–295. The article is published in the original.     

Novel itaconic acid-based superabsorbent polymer with improved gel strength and salt resistance using 2-acrylamido-2-methyl-1-propanesulfonic acid

The synthesis of novel superabsorbent polymers (SAPs) based on itaconic acid (IA) and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) is described for application in personal hygiene products such as disposable diapers. The AMPS is introduced to improve the low absorption performance of the existing IA-based SAPs. The salt-resistant properties of AMPS are shown to improve the absorption performance of SAP with respect to aqueous salt solutions. Further, the high ionization constant of the sulfonic acid group of AMPS contributes to the increase of the centrifugation retention capacity (CRC) of the SAP. Meanwhile, the amide group of AMPS improves the gel strength of the SAP by forming hydrogen bonds between the polymer chains. This increase in gel strength is demonstrated by the enhanced absorbency under load (AUL) and rheological analysis. The degree of neutralization affect the absorption properties of SAP, and the SAP exhibits maximum CRC and AUL of 57.3 and 14.4 g/g at 60% neutralization, respectively. As a crosslinking agent content increased, AUL increased but CRC significantly decreased. Additionally, soil pH evaluation confirms that SAP do not cause soil acidification.     

Properties of the forpolymer of N-vinylpyrrolidone with itaconic acid, acrylamide and 2-acrylamido-2-methyl-1-propane sulfonic acid as a fluid-loss reducer for drilling fluid at high temperatures

The forpolymer of N-vinylpyrrolidone (NVP), itaconic acid (IA), acrylamide (AM) and 2-acrylamido-2-methyl-1-propane sulfonic acid (AMPS) was synthesized through free-radical polymerization and was characterized using Fourier transform IR spectroscopy. The colloidal properties of the drilling fluid were investigated in the form of fresh-water or salt-water mud. It was found that the NVP–IA–AM–AMPS forpolymer had strong effects on the properties of the mud. The filtrate volume decreased with the increase of the forpolymer concentration before or after the aging test at 220 °C, and the filtrate volume after the aging test was larger than that before the aging test, but was still very small compared with the corresponding base mud. In addition, the rheological properties of both fresh-water mud and salt-water mud were modified by the forpolymer. The particle size data demonstrated that the average size of the clay particle after the aging test was larger than that before the aging test and that the particle size of the fresh-water mud was narrower compared with that of the salt-water mud before and after the aging test, respectively. The drilling fluid containing the forpolymer had an excellent tolerance to salt and high temperature. Received: 13 September 2000/Accepted: 9 January 2001     

Two-step surfactant binding of solvated and cross-linked poly(N-isopropylacrylamide-co- (2-acrylamido-2-methyl propane sulfonic acid))

 A solvated and cross-linked copolymer of N-isopropylacrylamide (IPAAm) and 2-(acrylamido)-2-methyl propane sulfonic acid (AMPS) was synthesized and its interaction with cationic surfactant lauryl-pyridinium chloride (C₁₂PyCl) was investigated. The solvated copolymer exhibited a lower critical solution temperature (LCST) in water, which was extensively shifted to a higher temperature due to the increase of hydrophilicity introduced by AMPS. In C₁₂PyCl solution, LCST of the copolymer was dramatically decreased due to the binding of C₁₂PyCl to AMPS unit, forming a stoichiometric complex. However, in the concentrated C₁₂PyCl solution, its LCST increased due to the non-stoichiometric complex formation. This phenomenon was further examined in the cross-linked copolymer, analyzed by binding isotherms. Two-step binding of surfactant was demonstrated followed by gel shrinking and re-swelling. This binding mechanism was further discussed regarding the effect of charge density and the hydro-phobicity of the main-chain backbone in terms of electrostatic and hydrophobic interactions. Received: 13 May 1997 Accepted: 13 August 1997     

邻偶氮萘醌磺酸基为负离子的二苯胺—4—重氮盐：———甲醛树脂的制备与性质

二苯胺－４－重氮盐与邻偶氮萘醌磺酸酯均具有很高的光敏性，分别是阴图型和阳图型预涂感光印刷版（ＰＳ版）的感光剂，用它们制备阴图型和阳图型ＰＳ版已有很多专利报道．重氮基与邻偶氮萘醌基的光分解分属两种类型，前者的中间体为自由基或正离子［１，２］，后者为碳卡...     

New reaction of the sodium salt of 2-nitroethanol. X-ray analysis of the sodium salt of 2-oxo-3-hydroxypropionic acid oxime, 2-bromo-2-nitropropane-1,3-diol,and the model 2,2-dinitropropane-1,3-diol

A novel reaction of the sodium salt of 2-nitroethanol in aqueous ammonia resulted in the sodium salt of 2-oxo-3-hydroxypropionic acid oxime (1) has been found. Bromination of1 affords 2-bromo-2-nitropropane-1,3-diol (2) with a previously unknown molecular conformation. The formation mechanisms of compounds1 and2 were suggested. X-ray analysis of products1,2 and that of the model compound, 2,2-dinitropropane-1,3-diol, was performed.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 1217–1221, May, 1996.     

Preparation and Characterization of Styrene/Butyl Acrylate Emulsifier-Free Latex with 2-Acrylamido-2-Methyl Propane Sulfonic Acid as a Reactive Emulsifier

A kind of emulsifier-free latex (FL) was successfully synthesized from styrene (St) and butyl acrylate (BA) with 2-acrylamido-2-methyl propane sulfonic acid (AMPS) as a reactive emulsifier. The particle size of latex particles, stability against electrolytes, minimum film forming temperature (MFT) and water contact angle (CA) were evaluated and compared with a conventional latex (CL). Test results show that FL has larger particle size, better stability against electrolytes and lower MFT value compared with CL; higher AMPS content leads to smaller particle size and smaller water CA.     

Spectrophotometric determination of clotrimazole and Phenylephrine-HCl in pharmaceutical formulation using 1, 2-naphthoquinone-4-Sulphonic acid sodium salt (NQS) as a chromogenic reagent

A sensitive, rapid and economical spectrophotometric method based on their interaction with NQS reagent in basic medium, which produces orange-colored complexes, has been devised to identify many drugs with amino groups (clotrimazole and phenylephrine-HCl). The maximum absorption for the complexes of clotrimazole and phenylephrine-HCl is 455 and 484 nm, respectively. Beer's law is applicable in the concentration ranges of (2–40) μg/ml for clotrimazole and (0–20) μg/ml for phenylephrine-HCl. The molar absorptivity values are 3931.1760 L/mol.cm and 4521.4074 L/mol.cm of clotrimazole and phenylephrine-HCl respectively with accuracy of 100.0285%–103.1456% and RSD better than 3.3211%. The method has been successfully used to determine these medications in pharmaceutical formulations, and it has been found to be superior to British Pharmacopeia standard procedures. At a 95% confidence level, F and t-tests are less than the tabulated values.     

Synthesis,characterization and application of 3‐methyl‐1‐sulfonic acid imidazolium tetrachloroferrate as nanostructured catalyst for the tandem reaction of β‐naphthol with aromatic aldehydes and amide derivatives

3‐methyl‐1‐sulfonic acid imidazolium tetrachloroferrate {[Msim]FeCl₄} was prepared and fully characterized by fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction (XRD), thermal gravimetric analysis (TGA), differential thermal gravimetric (DTG), field emission scanning electron microscopy (FESEM), energy dispersive X‐ray analysis (EDX) and vibrating sample magnetometer (VSM) and used, as an efficient catalyst, for the tandem reaction of β‐naphthol with aromatic aldehydes and benzamide at 110 °C under solvent‐free conditions to give 1‐amidoalkyl‐2‐naphthols in high yields and very short reaction times.     

Hydrogels of sodium alginate based copolymers grafted with sodium-2-acrylamido-2-methyl-1-propane sulfonate and methacrylic acid for controlled drug delivery applications

Novel sodium alginate based hydrogels were prepared by grafting the binary mixture of methacrylic acid and sodium-2-acrylamido-2-methyl-1-propane sulfonate on to sodium alginate (SA) with N,N'-methylenebisacrylamide (MBA) and ammonium persulfate (APS) as crosslinker and initiator respectively. The resultant SA-g-poly(AMPSNa-co-MAA) hydrogels were characterized using Fourier Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), Thermo Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and X-Ray Diffraction (XRD). The results indicated that an increase in the amount of sodium-2-acrylamido-2-methyl-1-propane sulfonate, swelling capacity was found to increase. The effects of temperature, pH and inorganic salt on the swelling behavior of the hydrogels were investigated. The pH reversibility behavior at pH levels of 1.0 and 9.0 indicated great potential of this hydrogel as a candidate system for controlled drug delivery.     

Effect of a copolymer poly(4-styrenesufonic acid-co-maleic acid) sodium salt on aggregation behavior of surface active ionic liquid 1-tetradecyl-3-methylimidazolium bromide and structurally similar conventional surfactant tetradecyltrimethylammonium bromide in aqueous media

The complex formation of anionic copolymer poly(4-styrenesufonic acid-co-maleic acid) sodium salt (PSSA-co-MA) with surfactant tetradecyltrimethylammonium bromide (TTAB) and surface active ionic liquid (SAIL) 1-tetradecyl-3-methylimidazolium bromide ([C₁₄mim][Br]) has been studied in aqueous media by utilizing various techniques such as tensiometry, conductometry and fluorimetry. Conductometric and tensiometric curve of all the investigated systems demonstrate four break points corresponding to four transition states. All the thermodynamic and surface properties of surfactant-polyelectrolyte systems have been determined by conductance and surface tension measurements respectively. The value of cmc decreases with increasing the concentration of polyelectrolyte for studied systems. But it has been observed that, the lowering in cmc values is more in [C₁₄mim][Br]-PSSA-co-MA system than TTAB-PSSA-co-MA system, although the differences in cmc are not much significant. The lowering in cmc of [C₁₄mim][Br]-PSSA-co-MA system shows that ionic attractions between cationic head group [C₁₄mim]⁺ and anionic parts (SO₃^? and COOH), are stronger than those in TTA⁺ and anionic parts (SO₃^? and COOH). The results indicated that the [C₁₄mim][Br]-PSSA-co-MA complexes are comparatively more surface active than TTAB-PSSA-co-MA complexes. The fluorescence probe behaviour also confirms cmc value and provides aggregation number (N_agg). Finally all the findings of [C₁₄mim][Br] and TTAB have been compared.