In vitro degradation of porous poly(l-lactide-co-glycolide)/β-tricalcium phosphate (PLGA/β-TCP) scaffolds under dynamic and static conditions

In vitro degradation of porous poly(l-lactide-co-glycolide)/β-tricalcium phosphate (PLGA/β-TCP) scaffolds was studied by incubating the samples in phosphate buffered saline (PBS) at 37 °C and pH 7.4 under dynamic loading with respect to static conditions for 12 weeks. Under dynamic conditions, acidity of PBS was alleviated by the better solution circulation, and water absorption of the scaffolds increased more than that under static conditions in the first 8 weeks. Changes in mass, height, diameter, relative molecular mass and its distribution also happened more remarkably under dynamic conditions. Moreover, obvious cracks and a larger amount of β-TCP particles were observed on the wall of the scaffolds after degradation for 12 weeks under dynamic loading. Compressive modulus and strength showed an increase from the beginning to the 10th week but were lower after then. Results showed that degradation of PLGA/β-TCP scaffolds under dynamic conditions exhibited a significantly faster rate than that under static conditions.     

Poly(l,l-lactide-co-glycolide)/tricalcium phosphate composite scaffold and its various changes during degradation in vitro

A poly(l,l-lactide-co-glycolide) (70/30)/(tricalcium phosphate) (PLGA/TCP) composite scaffold was fabricated by low-temperature deposition (LDM) and its degradation performed in vitro for 22 weeks. Various changes during degradation in vitro, which included changes in acidity of the degradation medium, morphology, weight, composition, molecular weight of the PLGA component and mechanical properties of the scaffold, were investigated. It was found that the acidity of degradation medium of the PLGA(70/30)/TCP composite scaffolds reduced and became much lower than that of TCP-free scaffold. With degradation, the volume and porosity of the PLGA(70/30)/TCP composite scaffold reduced at first then increased slowly, while the surface morphology of the scaffold changed from smooth to rough. The weight loss of the scaffold increased by dissolution of the degraded products and TCP component, but mainly by dissolution of the glycyl-rich degraded products of the PLGA component. The molecular weight of the PLGA component reduced with time, but the molecular weight distribution increased at first and then reduced. The compressive strength and modulus of the scaffold increased at first and then reduced with further degradation. The effect of degradation on modulus was much bigger than that on compressive strength. Based on excellent cell affinity of the PLGA(70/30)/TCP composite scaffold, a potentially useful bone tissue engineering scaffold is proposed.     

Load‐bearing biodegradable polycaprolactone‐poly (lactic‐co‐glycolic acid)‐ beta tri‐calcium phosphate scaffolds for bone tissue regeneration

A biodegradable scaffold with tissue ingrowth and load‐bearing capabilities is required to accelerate the healing of bone defects. However, it is difficult to maintain the mechanical properties as well as biodegradability and porosity (necessary for bone ingrowth) at the same time. Therefore, in the present study, polycaprolactone (PCL) and poly (lactic‐co‐glycolic acid) (PLGA5050) were mixed in varying ratio and incorporated with 20 wt.% beta tri‐calcium phosphate (βTCP). The mixture was shaped under pressure into originally nonporous cylindrical constructs. It is envisioned that the fabricated constructs will develop porosity with the time‐dependent biodegradation of the polymer blend. The mechanical properties will be sustained since the decrease in mechanical properties associated with the dissolution of the PLGA, and the formation of the porous structure will be compensated with the new bone formation and ingrowth. To prove the hypothesis, we have systematically studied the effects of samples composition on the time‐dependent dissolution behavior, pore formation, and mechanical properties of the engineered samples, in vitro. The highest initial (of as‐prepared samples) values of the yield strength (0.021 ± 0.002 GPa) and the Young's modulus (0.829 ± 0.096 GPa) were exhibited by the samples containing 75 wt.% of PLGA. Increase of the PLGA concentration from 25 to 75 wt.% increased the rate of biodegradation by a factor of 3 upon 2 weeks in phosphate buffered saline (1 × PBS). The overall porosity and the pore sizes increased with the dissolution time indicating that the formation of in situ pores can indeed enable the migration of cells followed by vascularization and bone growth.     

In Vivo Degradation Behavior of Porous Composite Scaffolds of Poly（lactide-co-glycolide） and Nano-hydroxyapatite Surface Grafted with Poly（L-lactide）

The biodegradable porous composite scaffold, composed of poly(lactide-co-glycolide)(PLGA) and hydroxyapatite nanoparticles(n-HAP) surface-grafted with poly(L-lactide)(PLLA)(g-HAP)(g-HAP/PLGA), was fabricated using the solvent casting/particulate leaching method, and its in vivo degradation behavior was investigated by the intramuscular implantation in rabbits. The composite of un-grafted n-HAP/PLGA and neat PLGA were used as controls. The scaffolds had interconnected pore structures with average pore sizes between 137 μm and 148 μm and porosities between 83% and 86%. There was no significant difference in the pore size and porosity among the three scaffolds. Compared with n-HAP/PLGA, the thermo-degradation temperature(Tc) of g-HAP/PLGA decreased while its glass transition temperature(Tg) increased. The weight change, grey value analysis of radiographs and SEM observation showed that the composite scaffolds of g-HAP/PLGA and n-HAP/PLGA showed slower degradation and higher mineralization than the pure PLGA scaffold after the intramuscular implantation. The rapid degradation of PLGA, g-HAP/PLGA and n-HAP/PLGA occurred at 8–12 weeks, 12–16 weeks and 16–20 weeks, respectively. Compared with n-HAP/PLGA, g-HAP/PLGA showed an improved absorption and biomineralization property mostly because of its improved distribution of HAP nanoparticles. The levels of both calcium and phosphorous in serum and urine could be affected to some extent at 3–4 weeks after the implantation of g-HAP/PLGA, but the biochemical detection of serum AST, ALT, ALP, and GGT as well as BUN and CRE showed no obvious influence on the functions of liver and kidney.     

3D printed PCL scaffold reinforced with continuous biodegradable fiber yarn: A study on mechanical and cell viability properties

In this study, poly (ε‐caprolactone) (PCL) scaffolds were printed and reinforced, simultaneously, with biodegradable poly glycolic acid (PGA) suture yarn, as a continuous reinforcing fiber, in the Fused Deposition Modeling (FDM) 3D printing process. Albeit PCL is a suitable material for biomedical applications, its low mechanical properties, and low degradation rate have limited its usage. A biocompatible suture yarn was used as the reinforcing material to enhance the mechanical properties and biodegradation characteristics, via an innovative method of continuous fiber embedding in the FDM process. The reinforced PCL samples were 3D printed with the setting porosity value of 60% and 0°/60°/120° lay-down pattern. The mechanical and biological properties of the scaffolds were tested to prove the effectiveness of the produced scaffolds for bone substitute purposes. Mechanical properties assessments showed that with a 22 vol.% suture yarn content in the 3D printed PCL scaffolds, the tensile strength, and elastic modulus remarkably increased up to 374% and 775%, respectively. The degradation of the reinforced PCL was 20 times higher than that of the non-reinforced PCL samples, after ten weeks, dominated by the fiber degradation phenomenon. After three days of cell culture, the proliferation assay of the built scaffovd the non-toxicity of the reinforced PCL.     

Polyester scaffolds with bimodal pore size distribution for tissue engineering

This paper presents a method for the preparation of porous poly(L-lactide)/poly[(L-lactide)-co-glycolide] scaffolds for tissue engineering. Scaffolds were prepared by a mold pressing-salt leaching technique from structured microparticles. The total porosity was in the range 70-85%. The pore size distribution was bimodal. Large pores, susceptible for osteoblasts growth and proliferation had the dimensions 50-400 microm. Small pores, dedicated to the diffusion of nutrients or/and metabolites of bone forming cells, as well as the products of hydrolysis of polyesters from the walls of the scaffold, had sizes in the range 2 nm-5 microm. The scaffolds had good mechanical strength (compressive modulus equal to 41 MPa and a strength of 1.64 MPa for 74% porosity). Scaffolds were tested in vitro with human osteoblast-like cells (MG-63). It was found that the viability of cells seeded within the scaffolds obtained using the mold pressing-salt leaching technique from structured microparticles was better when compared to cells cultured in scaffolds obtained by traditional methods. After 34 d of culture, cells within the tested scaffolds were organized in a tissue-like structure. Photos of section of macro- and mesoporous PLLA/PLGA scaffold containing 50 wt.-% of PLGA microspheres after 34 d of culture. Dark spots mark MG-63 cells, white areas belong to the scaffold. The specimen was stained with haematoxylin/eosin. Bar = 100 microm.     

Fabrication of poly(lactide‐co‐glycolide) scaffold embedded spatially with hydroxyapatite particles on pore walls for bone tissue engineering

Poly(lactide‐co‐glycolide) (PLGA) scaffolds embedded spatially with hydroxyapatite (HA) particles on the pore walls (PLGA/HA‐S) were fabricated by using HA‐coated paraffin spheres as porogens, which were prepared by Pickering emulsion. For comparisons, PLGA scaffolds loaded with same amount of HA particles (2%) in the matrix (PLGA/HA‐M) and pure PLGA scaffolds were prepared by using pure paraffin spheres as porogens. Although the three types of scaffolds had same pore size (450–600 µm) and similar porosity (90%–93%), the PLGA/HA‐S showed the highest compression modulus. The embedment of the HA particles on the pore walls endow the PLGA/HA‐S scaffold with a stronger ability of protein adsorption and mineralization as well as a larger mechanical strength against compression. In vitro culture of rat bone marrow stem cells revealed that cell morphology and proliferation ability were similar on all the scaffolds. However, the alkaline phosphatase activity was significantly improved for the cells cultured on the PLGA/HA‐S scaffolds. Therefore, the method for fabricating scaffolds with spatially embedded nanoparticles provides a new way to obtain the bioactive scaffolds for tissue engineering. Copyright © 2011 John Wiley & Sons, Ltd.     

Fabrication of 3D electrospun structures from poly(lactide‐co‐glycolide acid)–nano‐hydroxyapatite composites

The fabrication of three‐dimensional (3D) electrospun composite scaffolds was presented in this study. Layers of electrospun meshes made from composites of poly(lactide‐co‐glycolide acid) (PLGA) and hydroxyapatite (HA) were stacked and sintered using pressurized gas. Three HA concentrations of 5, 10, and 20 wt % were tested, and the addition of the HA nanoparticles decreased the tensile mechanical properties of the meshes with 20 wt % HA. However, after the gas absorption process, the fibers within the mesh sintered, which improved the mechanical properties more than twofold. The fabrication of 3D, porous, electrospun scaffolds was also demonstrated. The resulting 3D scaffolds had open porosity of up to 70% and modulus of ～20 MPa. This technique improves on the current electrospinning technology by overcoming the challenges of depositing a thick, 3D structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

低热-高压法制备PLGA多孔支架及其体外降解研究

采用低热-高压法制备了聚(dl-丙交酯／乙交酯)75／25(PLGA75／25)组织工程多孔支架。该方法避免了使用有机溶剂，支架的孔隙率在90％以上，孔径大小分布均匀。多孔支架经过酒精处理后，支架表面产生许多微小的凹陷；用藻酸钙改性处理后，支架形态保持良好。两种处理都使支架的压缩强度有所增大，亲水性增强。虽然孔隙率高的支架降解速率稍慢，但其体外降解规律基本一致：特性粘数争力学强度衰减快，而质量损失较慢，降解6周后，支架的质量损失仅为3％左右；体外降解3周后，支架的形态保持良好，可望在细胞移植争组织修复的早期发挥支撑作用。     

Effect of starch content on the biodegradation of polycaprolactone/starch composite for fabricating in situ pore-forming scaffolds

Bone tissue engineering is an efficient approach to regenerating bone-related defects. The optimal scaffold used for bone tissue engineering must possess adequate porosity and suitable mechanical properties. This work described the development of a biodegradable polymeric composite based on polycaprolactone (PCL) and starch that can form a porous structure in situ. The scaffold exhibited the required mechanical properties at the initial stage of implantation by controlling in situ degradation and subsequent pore formation. PCL/starch (SPCL) scaffolds with 100/0, 70/30, and 50/50 ratios were developed. Degradation studies were performed in phosphate buffer saline (PBS) containing α-amylase or lipase at 37 °C for 4 weeks. Fourier-transform infrared spectroscopy was used to analyze chemical bonds and their changes after degradation. Differential scanning calorimetry was applied to determine the crystallinity and recrystallization of samples before and after degradation. Mass loss and starch release were observed during degradation, and the porosity of samples was measured by the ethanol replacement method. Morphology was further determined using scanning electron microscopy. Finally, variations in compressive strength and modulus during degradation and pore formation were also measured. The porosity of samples reached 45% after 1 month of degradation, and mechanical properties were still appropriate for human bone tissue. Reduction in mechanical property after mass loss, starch release and pore formation was controlled by the hydrogen bonding and recrystallization effect of PCL after degradation. Results suggested that SPCL composite had potential to form porous scaffold with adequate mechanical properties in situ and is promising for bone tissue engineering applications.     

聚酯多孔支架降解液对骨髓基质干细胞活力和成骨分化的影响

通过室温模压/粒子浸出方法制备得到聚乙交酯丙交酯(PLGA)多孔支架,每个质量50 mg、孔径200～300μm、孔隙率略大于90%的PLGA85/15多孔支架在10 mL磷酸盐缓冲液(PBS)中37℃体外降解24周.降解液每周换一次,不同时间点的降解液被收集、并加入骨髓基质干细胞(MSC)的培养液或者成骨诱导液中,利用胞外乳酸脱氢酶含量检测、细胞死活染色、四唑盐检测、碱性磷酸酶染色和定量检测的方法考察降解液对MSC的活力和成骨分化能力的影响.实验结果表明,PLGA多孔支架材料在PBS中逐渐降解,其质量、尺寸、孔径、孔与孔的连通性、分子量有不同程度的降低;其降解液在本研究的实验条件下未发现对MSC有明显的细胞毒性,对MSC的活力、增殖以及成骨分化均无显著的负面影响.     

Cellulose nanocrystals as biobased nucleation agents in poly-l-lactide scaffold: Crystallization behavior and mechanical properties

The mechanical strength of polymer scaffold is closely related to its crystallinity. In this work, cellulose nanocrystals (CNC) were incorporated into poly-l-lactide (PLLA) scaffold which was fabricated by selective laser sintering, aiming to improve the mechanical properties. CNC possesses numerous hydroxyl groups which might form hydrogen bond with PLLA molecular chains. The hydrogen bond induces the ordered arrangement of PLLA chain by using CNC as heterogeneous nucleating agent, thereby increasing crystallization rate and crystallinity. Results showed that PLLA scaffolds with 3 wt% CNC resulted in 191%, 351%, 34%, 83.5%, 56% increase in compressive strength, compressive modulus, tensile strength, tensile modulus and Vickers hardness, respectively. Encouragingly, with the incorporation of hydrophilic CNC, the PLLA/CNC scaffolds showed not only better hydrophilicity, but also faster degradation than PLLA. In vitro cell culture studies proved that the PLLA/CNC scaffolds were biocompatible and capable of supporting cell adhesion, proliferation and differentiation. The above results indicated that the PLLA/CNC scaffolds may therefore be a potential replacement in bone repair.     

Mechanical properties and degradation studies of poly(D,L‐lactide‐co‐glycolide) 50:50/graphene oxide nanocomposite films

Poly(D,L‐lactide‐co‐glycolide) 50:50 (PLGA)/graphene oxide (GO) nanocomposite films were prepared with various GO weight fractions. A significant enhancement of mechanical properties of the PLGA/GO nanocomposite films was obtained with GO weight fractions. The incorporation of only 5 wt% of GO resulted in an ~2.5‐fold and ~4.7‐fold increase in the tensile strength and Young's modulus of PLGA, respectively. The thermomechanical behaviors of composite films were investigated by dynamic mechanical analysis. Results indicated that the values of T_g and storage moduli of the PLGA/GO composites were higher than those of the pristine PLGA. The improvement in oxygen barrier properties of composites was presumably attributed to the filler effect of the randomly dispersed GO throughout the PLGA matrix. In this work, we also studied in vitro biodegradation behavior. PLGA/GO composite films were hydrolyzed at 37°C for periods up to 49 days. Because of the presence of GO nanosheets, degradation of composite films took place more slowly with increasing GO amounts. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of porogen on the physico-chemical properties and degradation performance of PLGA scaffolds

The aim of the study was to examine the relationship between the structural features of PLGA 3-D scaffolds and their degradation performances. PLGA 3-D scaffolds were fabricated by solvent casting and particulate leaching using salt and sucrose particles as porogen and they were characterized in terms of structure, physico-chemical and mechanical properties. The in vitro degradation study was performed at 37 °C in PBS for 28 days and it included the determination of Mw, Mn, PI, water uptake, mass loss and pH changes of the degradation buffer. It was found that the preparation method scaffolds, in particular the choice of the porogen type and was responsible for the three-dimensional structure (pore size, porosity, apparent density and, mechanical properties) of the scaffold and for physico-chemical PLGA polymer modifications (polymer degradation reactions, polymer chain rearrangement, Tg changes). Scaffolds with high porosity (83.8-89.4%) and an interconnected network were obtained.     

Montmorillonite reduces crystallinity of poly‐l‐lactic acid scaffolds to accelerate degradation

Poly‐l‐lactic acid (PLLA) is considered as a potential bone scaffold material because of good biocompatibility and bioabsorbability, whereas too slow degradation rate limits its application. In this study, montmorillonite (MMT) was introduced into PLLA scaffolds fabricated via selective laser sintering to accelerate degradation by reducing crystallinity. To be specific, MMT was a layered silicate with large surface area and aspect ratio, which provided nucleation site for the crystallization of PLLA molecular chain along their surface during the sintering process. As the surface of MMT plate was randomly oriented in the matrix, the growth direction of crystallite was also random, which interrupted the orderly crystallization, thus decreasing the overall crystallinity of PLLA. As a result, the crystallinity of PLLA scaffolds was decreased from 32.3% to 27.4% when introducing 4.5% MMT. Accordingly, weight loss was increased from 0.83% to 7.25% after immersing for 4 weeks. Besides, the tensile strength and modulus of the scaffolds increased by 44.1% and 66.9% because of the change of fracture mode from brittle fracture to ductile fracture. In addition, the scaffolds also demonstrated good hydrophilic property and cell compatibility.     

Functionalized-graphene/ethylene vinyl acetate co-polymer composites for improved mechanical and thermal properties

The surface functionalization of graphene and the preparation of functionalized graphene/ethylene vinyl acetate co-polymer (EVA) composites by solution mixing are described. Octadecyl amine (ODA) was selected as a surface modifier for the preparation of functionalized graphene (ODA-G) in an aqueous medium. The ODA-G was characterized by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy, which confirm the modification and reduction of graphite oxide to graphene. Atomic force microscopy shows that the average thickness of ODA-G is ca. 1.9 nm. The ODA-G/EVA composites were characterized by X-ray diffraction and transmission electron microscopy, which confirms the formation of ODA-G/EVA composites. Measurement of tensile properties shows that the tensile strength of the composites (with 1 wt.% ODA-G loading) is ∼74% higher as compared to pure EVA. Dynamic mechanical analysis shows that the storage modulus of the composites is much higher than that of pure EVA. The thermal stability of the composite with 8 wt.% of ODA-G is ∼42 °C higher than that of pure EVA. The electrical resistivity has also decreased in the composites with 8 wt.% of ODA-G.     

Partially resorbable composite bone plate with controlled degradation rate, desired mechanical properties and bioactivity

Rate of polymer degradation is very important for implantable biomaterials since controlling the degradation rate may complement the biological response and affected mechanical property requirements. In spite of numerous publications on the potential use of combinations of poly lactic acid/bioactive glass fillers for degradable bone plate, little information exists on the controlling degradation rate and its effects on the other aspects such as biomechanical compatibility, bioactivity, etc. Our previous study revealed that a composite bone plate consist of poly l-lactic acid/braided bioactive glass fibers has the initial mechanical properties near to cortical bone. In this study, degradation rate and mechanical behavior of the composite bone plate were assessed, and also degradation rate was controlled by using proper manufacturing process and improving bonding between matrix and reinforcement. Moreover, bioactivity of the composite was considered before and after controlling degradation rate, because of the important role of bioactivity and ion release in healing acceleration. Results showed that degradation process of the composite could be controlled properly. Strength of the treated composite decreased only about 5% through 2 weeks and about 35% after 8 weeks while, the strength loss for the untreated composites was about 50 and 70 percent after 2 weeks and 8 weeks of degradation respectively. Although calcium-phosphate formation on the surface of the composite was postponed in the treated samples, the bioactivity of the composite remained unchanged and bone-like apatite was formed on the composite surface which is important for the application of the composite in bone tissue environment.     

Fabrication of open‐porous PCL/PLA tissue engineering scaffolds and the relationship of foaming process,morphology, and mechanical behavior

Tissue engineering scaffolds should provide a suitable porous structure and proper mechanical strength, which is beneficial for the delivery of growth factor and regulation of cells. In this study, the open‐porous polycaprolactone (PCL)/poly (lactic acid) (PLA) tissue engineering scaffolds with suitable porous scale were fabricated using different ratios of PCL/PLA blends. At the same time, the relationship of foaming process, morphology, and mechanical behavior in the optimized batch microcellular foaming process were studied based on the single‐factor experiment method. The porous structures and mechanical strength of the scaffolds were optimized by adjusting foaming parameters, including the temperature, pressure, and CO₂ dissolution time. The results indicated that the foaming parameters influence the cell morphology, further determine the mechanical behavior of PCL/PLA blends. When the PCL content is high, with the increase of temperature and time, the cell diameter and the elastic modulus increased, and the tensile strength and elastic modulus increased with the increase of the average cell size, and decreased as the increase of the cell density. While when the PLA content was high, the cell diameter showed the same trend, and the tensile strength and elastic modulus were higher, and the elongation at break was lower, and tensile strength and elastic modulus decreased with the increase of the average cell size and increased with the increase of cell density. This work successfully fabricated optimized porous PCL/PLA scaffolds with excellent suitable mechanical properties, pore sizes, and high interconnectivity, indicating the effectiveness of modulating the batch foaming process parameters.     

Preparation and modification of collagen-based porous scaffold for tissue engineering

In the effort to generate cartilage tissues using mesenchymal stem cells, porous scaffolds with prescribed biomechanical properties were prepared. Scaffolds with interconnected pores were prepared via lyophilisation of frozen hydrogels made from collagen modified with chitosan nanofibres, hyaluronic acid, copolymers based on poly(ethylene glycol) (PEG), poly(lactic-co-glycolic acid) (PLGA), and itaconic acid (ITA), and hydroxyapatite nanoparticles. The modified collagen compositions were cross-linked using N-(3-dimethylamino propyl)-N′-ethylcarbodiimide hydrochloride (EDC) combined with N-hydroxysuccinimide (NHS) in water solution. Basic physicochemical and mechanical properties were measured and an attempt to relate these properties to the molecular and supermolecular structure of the modified collagen compositions was carried out. Scaffolds containing hydrophilic chitosan nanofibres showed the highest swelling ratio (SR = 20–25) of all the materials investigated, while collagen modified with an amphiphilic PLGA-PEG-PLGA copolymer or functionalised with ITA exhibited the lowest swelling ratio (SR = 5–8). The best resistance to hydrolytic degradation was obtained for hydroxyapatite containing scaffolds. On the other hand, the fastest degradation rate was observed for synthetic copolymer-containing scaffolds. The results showed that the addition of hydroxyapatite or hyaluronic acid to the collagen matrix increases the rigidity in comparison to the collagen-chitosan scaffold. Collagen scaffold modified with hyaluronic acid presented reduced deformation at break while the presence of hydroxypatatite enhanced the scaffold deformation under tensile loading. The tensile elastic modulus of chitosan nanofibre collagen scaffold was the lowest but closest to the articular cartilage; however, the strength and deformation to failure increased up to 200 %. Presented at the 1st Bratislava Young Polymer Scientists Workshop, Bratislava, 20–23 August 2007.     

Degradation as a result of UV radiation of bloodmeal-based thermoplastics

Polymers are known for their susceptibility to degradation as a result of ultra-violet (UV) radiation. In this study, the UV stability of bloodmeal-based thermoplastics (BMT) was evaluated over a period of 12 weeks. Formulations with and without plasticiser were tested and moisture was excluded during accelerated weathering to isolate the effect of UV because of the material’s known sensitivity to moisture. It was found that embrittlement due to loss of water overshadowed the effect of UV degradation. Embrittlement caused the material’s toughness to be reduced by an order of magnitude after only two weeks of exposure, for either plasticised or unplasticised samples. An initial increase in tensile strength was observed after two weeks followed by a steady decline in strength. The elastic modulus reached a plateau after about two weeks of exposure. FTIR did not confirm any chemical changes after 12 weeks exposure and TGA suggested that low molecular mass species were quickly lost during the course of the test. The absence of chemical changes does not suggest resistance to environmental degradation, although the dark pigmentation of bloodmeal may have contributed to the lack of UV degradation. Embrittlement remains a greater concern and requires further attention.