首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
We have already shown that polylactide (PLA) nanoparticles covered with a hydrophilic polymeric layer can be prepared by simple emulsion/solvent evaporation by using amphiphilic copolymers as surfactants during the procedure. The external layer is then constituted by the hydrophilic part of the macromolecular surfactant. This kind of nanospheres is useful for the encapsulation of lipohilic molecules. The use of amphiphilic copolymers as surfactants in the preparation of PLA nanospheres with controlled surface properties, was then applied to the double emulsion/solvent evaporation procedure. The aim was to allow the encapsulation of water-soluble bioactive molecules in PLA particles with controlled surface properties. In this paper, we describe the results obtained with three different water-soluble monomethoxypolyethylene oxide (MPEO)-b-PLA diblock copolymers used as surfactants in the preparation of nanoparticles by double emulsion/solvent evaporation. After organic solvent evaporation, the obtained nanospheres were proved to be really covered by a MPEO layer whose characteristics were determined. It was firstly shown that the MPEO-covered particles did not flocculate at 25 degrees C, even in 4 M NaCl while suspensions of bare nanospheres were destabilized for a NaCl concentration as low as 0.04 M. On the other hand, the suspensions of MPEO-covered nanoparticles in 0.3 M Na2SO4 were found to be very sensitive to temperature as they flocculated at a temperature lying between 45 and 55 degrees C depending on the MPEO-b-PLA composition. This property was attributed to the fact that MPEO is a polymer with a low critical solution temperature. The concentration of MPEO at the nanoparticle surface was then calculated for the three kinds of particles, from the initial flocculation temperature, and was found to be comparable to the value determined directly.  相似文献   

2.
Evaporating droplets of volatile organic solvent containing amphiphilic block copolymers may undergo hydrodynamic instabilities that lead to dispersal of copolymer micelles into the surrounding aqueous phase. As for related phenomena in reactive polymer blends and oil/water/surfactant systems, this process has been ascribed to a nearly vanishing or transiently negative interfacial tension between the water and solvent phases induced by adsorption of copolymer to the interface. In this report, we investigate the influence of the choice of organic solvent and polymer composition for a series of polystyrene-b-poly(ethylene oxide) (PS-PEO) diblock copolymers, by in situ micropipette tensiometry on evaporating emulsion drops. These measurements suggest that the sensitivity to the organic solvent chosen reflects both differences in the bare solvent/water interfacial tension as well as the propensity of the copolymer to aggregate within the organic phase. While instabilities coincident with an approach of the interfacial tension nearly to zero were observed only for copolymers with PEO content greater than 15 wt.%, beyond this point the interfacial behavior and critical concentration needed to trigger surface instability were found to depend only weakly on copolymer composition.  相似文献   

3.
两亲磁性高分子微球的合成与表征   总被引:7,自引:0,他引:7  
在Fe3O4磁流体存在下 ,通过苯乙烯与聚氧乙烯大分子单体 (MPEO)分散共聚制备两亲磁性高分子微球 .研究了聚氧乙烯大分子单体对微球粒径的影响 .用扫描电子显微镜 (SEM)、原子力显微镜 (AFM)表征了磁性微球的粒径、表面形貌以及表面粗糙度 ,用傅立叶红外光谱 (FTIR)鉴定了共聚物的结构 .随着聚合物中聚氧乙烯大分子单体含量的增加 ,微球表面的粗糙度增加 ,通过改变共聚物中MPEO的含量 ,可以得到含有 0 4~ 3 5mg g羟值的两亲磁性高分子微球  相似文献   

4.
We developed a novel "spray dry-based" method for preparing surface-modified particle via "block copolymer-assisted" emulsification/evaporation for pulmonary drug delivery. The method included three steps: (1) o/w emulsion containing both hydrophobic polymers and amphiphilic block copolymers was obtained by emulsification of water and a polymer-containing organic solvent, (2) the o/w emulsion was misted with a nebulizer, and (3) the emulsion mists were dried by a heater. In this way, the hydrophobic polymers and the hydrophobic part of the amphiphilic block copolymers gradually tangled during the evaporation of organic solvents from the o/w emulsion. Consequently, the hydrophilic polymer chain was introduced on the particle surface. The particle surface can be easily modified although there are no reactive groups in the hydrophobic polymer molecules. We successfully obtained dry PEG-PLA/PLGA microparticles by controlling the weight ratio of the block copolymer and the hydrophobic polymer. The introduction of PEG to the particle surface involves an increase in the Zeta potential of the particles. Interestingly, the "dimpled" microparticles having a diameter of approximately 2 μm were obtained. The "dimpled" microparticles can serve as drug carriers for pulmonary drug delivery, because the particles have a large surface area. We expect that this novel surface-modification technique will enable efficient fabrication of particles in drug delivery systems.  相似文献   

5.
Polysaccharide-covered polyester nanoparticles were prepared using the emulsion/solvent evaporation process. The core of the nanoparticles was made either of PLA or of a blend of polylactide and polylactide-grafted dextran copolymer in various proportions. The surface of the nanoparticles was covered by dextran chains via the use of water-soluble polylactide-grafted dextrans as polymeric stabilizers during the emulsification step. The characteristics of the nanoparticles (size, surface coverage, thickness of superficial layer, colloidal stability) were correlated to the structural parameters (length and number of polylactide grafts) of the copolymers as well as to their surface active properties. The complete biodegradability of the nanoparticles was evaluated by considering the rate of hydrolysis of polylactide grafts in phosphate buffer and the rate of enzymatic degradation of dextran backbone by dextranase.  相似文献   

6.
Strongly ionized amphiphilic diblock copolymers of poly(styrene)-b-poly(styrenesulfonate) with various hydrophilic and hydrophobic chain lengths were synthesized by living radical polymerization, and their properties and self-assembling behavior were systematically investigated by surface tension measurement, foam formation, hydrophobic dye solubilization, X-ray reflectivity, dynamic light scattering, small-angle neutron scattering, small-angle X-ray scattering, and atomic force microscope techniques. These copolymer solutions in pure water did not show a decrease of surface tension with increasing polymer concentration. The solutions also did not show foam formation, and no adsorption at the air/water interface was confirmed by reflectivity experiments. However, in 0.5 M NaCl aq solutions polymer adsorption and foam formation were observed. The critical micelle concentration (cmc) was observed by the dye solubilization experiment in both the solutions with and without added salt, and by dynamic light scattering we confirmed the existence of polymer micelles in solution, even though there was no adsorption of polymer molecules at the water surface in the solution without salt. By the small-angle scattering technique, we confirmed that the micelles have a well-defined core-shell structure and their sizes were 100-150 A depending on the hydrophobic and hydrophilic chain length ratio. The micelle size and shape were unaffected by addition of up to 0.5 M salt. The absence of polymer adsorption at the water surface with micelle formation in a bulk solution, which is now known as a universal characteristic for strongly ionized amphiphilic block copolymers, was attributed to the image charge effect at the air/water interface due to the many charges on the hydrophilic segment.  相似文献   

7.
Diblock and multiblock copolymers composed of a poly(D,L-lactide) (PLA) or poly(trimethylene carbonate) (PTMC) core with a hydrophilic chain of poly(ethylene glycol) (PEG) were prepared. These copolymers, in which the core is connected to PEG through a polyfunctional molecule such as citric, mucic, or tartaric acid, may be used to form nanoparticles for drug delivery applications. Branched copolymers were prepared by direct amidation between the polyfunctional acid and methoxy PEGamine, followed by ring-opening polymerization of lactide or trimethyl carbonate to form the PLA and PTMC block copolymers. In addition, a complex multiblock copolymer of biotin-PEG-poly[lactic-co-(glycolic acid)] (PLGA) for application in an avidin-biotin system was prepared for possible design of nanospheres with targeting properties. Studies of drug release from polymeric systems containing multiblock copolymers and studies of polymer degradation were also performed.  相似文献   

8.
Poly(lactic acid) (PLA) and poly(lactic/glycolic acid) copolymers (PLGA) are biodegradable drug carriers of great importance, although successful pharmaceutical application requires adjustment of the surface properties of the polymeric drug delivery system to be compatible with the biological environment. For that reason, reduction of the original hydrophobicity of the PLA or PLGA surfaces was performed by applying a hydrophilic polymer poly(ethylene oxide) (PEO) with the aim to improve biocompatibility of the original polymer. PEO-containing surfaces were prepared by incorporation of block copolymeric surfactants, poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (Pluronic), into the hydrophobic surface. Films of polymer blends from PLA or PLGA (with lactic/glycolic acid ratios of 75/25 and 50/50) and from Pluronics (PE6800, PE6400, and PE6100) were obtained by the solvent casting method, applying the Pluronics at different concentrations between 1 and 9.1% w/w. Wettability was measured to monitor the change in surface hydrophobicity, while X-ray photoelectron spectroscopy (XPS) was applied to determine the composition and chemical structure of the polymer surface and its change with surface modification. Substantial reduction of surface hydrophobicity was achieved on both the PLA homopolymer and the PLGA copolymers by applying the Pluronics at various concentrations. In accordance with the wettability changes the accumulation of Pluronics in the surface layer was greatly affected by the initial hydrophobicity of the polymer, namely, by the lactide content of the copolymer. The extent of surface modification was also found to be dependent on the type of blended Pluronics. Surface activity of the modifying Pluronic component was interpreted by using the solubility parameters.  相似文献   

9.
The effect of crystallinity of polylactide (PLA) on the structure and properties of tough PLA blends with PEG-b-PPG-b-PEG block copolymers was studied. PLA was melt blended with a set of the copolymers with varying ratio of the hydrophilic (PEG) and hydrophobic (PPG) blocks. Although the blend phase structure depended on the copolymer molar mass and PEG content, as well as on the copolymer concentration in the blend, crystallinity also played an important role, increasing the copolymer content in the amorphous phase and enhancing phase separation. The influence of crystallinity on the thermal and mechanical properties of the blends depended on the copolymer used and its content. The blends, with PLA crystallinity of 25 ÷ 34 wt%, exhibited relatively high glass transition temperature ranging from 45 to 52 °C, and melting beginning above 120 °C. Although with a few exceptions crystallinity worsened the drawability and toughness, these properties were improved with respect to neat crystalline PLA in the case of partially miscible blends, in which fine liquid inclusions of the modifier were dispersed in PLA rich matrix. About 20-fold increase of the elongation at break and about 4-fold increase of the tensile impact strength were reached at a small content (10 wt%) of the modifier. Moreover, crystallinity decreased oxygen and water vapor transmission rates through neat PLA and the blend, and the barrier property for oxygen of the latter was better than that of neat polymer.  相似文献   

10.
Polystyrene–poly(ethylene oxide) PS–PEO di- and triblock copolymers have been used as stabilizers in the emulsion polymerization of styrene and styrene–butylacrylate for the preparation of “hairy latexes”. The polymerization kinetics and the efficiency of these polymeric surfactants were correlated with the molecular characteristics of the block copolymer. It was shown that the efficiency decreased with increasing molecular weight and PS content of the block copolymer. The PEO frige, with a thickness of 4–25 nm, on the latex particle surface could be characterized and it was shown by differential scanning calorimetry (DSC) that water is strucured in that PEO layer. Film formation with “hairy latexes” was also examined both by DSC and thermomechanical analysis. The properties and application possibilities, such as in controlled latex flocculation, have been reviewed.  相似文献   

11.
In many applications surfaces are modified using polymer films and the polymers used are often complex copolymers. In biomedical applications it is critical to determine the surface properties of a substrate as it is these that mediate the cellular interactions. The surface structure of copolymer films can only rarely be established from their bulk composition alone. In this study angle resolved XPS was used to build a model of the structure of copolymer films produced on glass substrates from a family of poly(acrylamide) copolymers containing cationic blocks. The thickness of the copolymer films was demonstrated to be dependent on the concentration of the polymer solution and the ratio of non‐cationic to cationic blocks in the copolymer. The data demonstrated that the cationic blocks of the copolymer preferentially segregated to the glass surface and the non‐cationic poly(acrylamide) blocks preferentially segregated to the air–vacuum interface. A low concentration of the cationic functional groups was present throughout the poly(acrylamide) layer and it was suggested that this resulted from a small fraction of the cationic blocks being pulled into the poly(acrylamide) layer at points along the polymer chain where the two blocks are connected. Evidence of a thin surface hydrocarbon contamination layer was also observed. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

12.
We reported previously (Macromolecules 2003, 36, 5321; Langmuir, 2004, 20, 7412) that amphiphilic diblock copolymers having polyelectrolytes as a hydrophilic segment show almost no surface activity but form micelles in water. In this study, to further investigate this curious and novel phenomenon in surface and interface science, we synthesized another water-soluble ionic amphiphilic diblock copolymer poly(hydrogenated isoprene)-b-sodium poly(styrenesulfonate) PIp-h2-b-PSSNa by living anionic polymerization. Several diblock copolymers with different hydrophobic chain lengths were synthesized and the adsorption behavior at the air/water interface was investigated using surface tension measurement and X-ray reflectivity. A dye-solubilization experiment was carried out to detect the micelle formation. We found that the polymers used in this study also formed micelles above a certain polymer concentration (cmc) without adsorption at the air-water interface under a no-salt condition. Hence, we further confirmed that this phenomenon is universal for amphiphilic ionic block copolymer although it is hard to believe from current surface and interface science. For polymers with long hydrophobic chains (more than three times in length to hydrophilic chain), and at a high salt concentration, a slight adsorption of polymer was observed at the air-water interface. Long hydrophobic chain polymers showed behavior "normal" for low molecular weight ionic surfactants with increasing salt concentration. Hence, the origin of this curious phenomenon might be the macroionic nature of the hydrophilic part. Dynamic light scattering analysis revealed that the hydrodynamic radius of the block copolymer micelle was not largely affected by the addition of salt. The hydrophobic chain length-cmc relationship was found to be unusual; some kind of transition point was found. Furthermore, very interestingly, the cmc of the block copolymer did not decrease with the increase in salt concentration, which is in clear contrast to the fact that cmc of usual ionic small surfactants decreases with increasing salt concentration (Corrin-Harkins law). These behaviors are thought to be the special, but universal, characteristics of ionic amphiphilic diblock copolymers, and the key factor is thought to be a balance between the repulsive force from the water surface by the image charge effect and the hydrophobic adsorption.  相似文献   

13.
高分子表面活性剂P(AM-co-OPMA)的合成与表征   总被引:1,自引:1,他引:0  
辛基酚聚氧乙烯醚(10)(OP-10)与马来酸酐在95℃下反应,合成了辛基酚聚氧乙烯醚马来酸单酯(OPMA);并在水溶液中与丙烯酰胺(AM)单体进行共聚合,获得了高分子表面活性剂P(AM-co-OPMA);考察了引发剂用量、单体组成、单体总浓度及反应温度对共聚物特性粘数与阴离子度的影响.通过红外光谱、紫外光谱、荧光发射光谱和电导滴定对共聚物结构和组成进行了表征;利用视频光学接触角测量仪分别测定了共聚物表面和界面张力.结果表明,在聚丙烯酰胺分子主链上引入OPMA链节后,不仅保持了PAM优良的增稠能力(特性粘数达764.31 mL/g),且赋予了共聚物较高的表面活性(浓度为1.5 g/L共聚物水溶液的表面和界面张力分别可达53.94 mN/m和5.41 mN/m).  相似文献   

14.
The “topological polymer chemistry” of amphiphilic linear and cyclic block copolymers at an air/water interface was investigated. A cyclic copolymer and two linear copolymers (AB‐type diblock and ABA‐type triblock copolymers) synthesized from the same monomers were used in this study. Relatively stable monolayers of these three copolymers were observed to form at an air/water interface. Similar condensed‐phase temperature‐dependent behaviors were observed in surface pressure–area isotherms for these three monolayers. Molecular orientations at the air/water interface for the two linear block copolymers were similar to that of the cyclic block copolymer. Atomic force microscopic observations of transferred films for the three polymer types revealed the formation of monolayers with very similar morphologies at the mesoscopic scale at room temperature and constant compression speed. ABA‐type triblock linear copolymers adopted a fiber‐like surface morphology via two‐dimensional crystallization at low compression speeds. In contrast, the cyclic block copolymer formed a shapeless domain. Temperature‐controlled out‐of‐plane X‐ray diffraction (XRD) analysis of Langmuir–Blodgett (LB) films fabricated from both amphiphilic linear and cyclic block copolymers was performed to estimate the layer regularity at higher temperatures. Excellent heat‐resistant properties of organized molecular films created from the cyclic copolymer were confirmed. Both copolymer types showed clear diffraction peaks at room temperature, indicating the formation of highly ordered layer structures. However, the layer structures of the linear copolymers gradually disordered when heated. Conversely, the regularity of cyclic copolymer LB multilayers did not change with heating up to 50 °C. Higher‐order reflections (d002, d003) in the XRD patterns were also unchanged, indicative of a highly ordered structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 486–498  相似文献   

15.
《先进技术聚合物》2018,29(3):1094-1106
The introduction of non‐modified kraft LignoBoost® lignin (KL) to produce polymer hybrid latex has received much attention in recent years because it is derived from renewable resources. The focus of this work is to develop a polymer hybrid latex by emulsion and miniemulsion copolymerization of styrene with n‐butyl acrylate and methacrylic acid in the presence of different concentrations of KL furnished by the pulp and paper industry. The study intends to substitute a styrene in the system to understand the effect of non‐modified KL on the properties not only of the latexes, but also on the copolymers themselves. Each polymerization was carried out by shot‐process of tertbutyl hydroperoxide and sodium formaldehyde sulfoxylate as the redox system. The polymer latexes were characterized in relation to overall conversion, particle diameter, particle morphology, coagulum formation, surface tension, zeta potential, and atomic force microscopy. The polymers were evaluated through gel permeation chromatography, water absorption, and thermal properties. The results show that the addition of non‐modified KL results in inhibition of the polymerization and that KL acts as a colloid stabilizer. Small particles were generated in the initial stages of the polymerizations. The presence of the KL altered the color of the latexes; the increase in KL concentration resulted in increase in the absorption of water of the polymer films; the increase in KL concentration resulted in decrease of the molar mass of the copolymers.  相似文献   

16.
用含氟丙烯酸酯无规共聚物制备超疏水膜   总被引:4,自引:0,他引:4  
用微乳液聚合法制备了丙烯酸全氟烷基乙酯和甲基丙烯酸甲酯的无规共聚物,并对其进行了表征.采用溶剂挥发成膜法一步制备了具有超疏水性的该聚合物膜,水滴在该聚合物膜上的静态接触角可达151°~160°,滚动角小于3°.通过扫描电子显微镜观察发现该聚合物膜表面分布了许多乳突状突起和微孔洞,并具有微米和纳米尺度相结合的复合杂化结构.该类超疏水表面的形成是由适度粗糙的表面和低表面能相互结合引起的.探讨了该类超疏水膜的形成机理.  相似文献   

17.
Hydrophobic–hydrophilic block copolymers were prepared by “living” anionic polymerization. They consist of polystyrene and poly(ethylene oxide) blocks, and are soluble in water. Their interfacial properties were investigated, employing aqueous solutions. The block copolymers lowered the surface tension of water in analogy with the low molecular weight surfactants such as sodium lauryl sulfate and heptaethylene oxide n-dodecyl ether. Their aqueous solutions exhibited solubilization properties differing from those of polyethylene glycol. Therefore, it is thought that the polystyrene blocks produce solubilization phenomena. In samples of the same styrene content, the precipitation temperature of a high molecular weight copolymer in water was lower than that of a low molecular weight copolymer at the same concentration in the same solvent. The surface tension and precipitation temperature of aqueous solutions seem to be influenced by molecular weight and composition.  相似文献   

18.
Polymeric nanospheres consisting of poly(methyl methacrylate) (PMMA) cores and poly(ethylene glycol) (PEG) branches on their surfaces were prepared by free radical copolymerization of methyl methacrylate (MMA) with PEG macromonomers in ethanol/water mixed solvents. PEG macromonomers having a methacryloyl (MMA‐PEG) and p‐vinylbenzyl (St‐PEG) end group were used. It has become clear that the obtained polymer dispersions form three kinds of states, particle dispersion (milky solution), clear solution, and gel/precipitation. It was found that the reaction parameters such as MMA concentration, molecular weight, and concentration of PEG macromonomers, and water content can affect nanosphere formation in a copolymerization system. The water volume fraction of mixed ethanol/water solvents affected the particle size of the nanospheres. These differences in the formation of nanospheres were due to the solvophilic/solvophobic balance between the copolymers and solvents during the self‐assembling process of the copolymers. The sizes of nanospheres can be controlled by varying concentration of PEG macromonomer and water content in solvents. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1811–1817, 2000  相似文献   

19.
醇/水介质对PEG大分子单体与BMA分散共聚反应的影响   总被引:1,自引:0,他引:1  
通过端基反应法合成了苯乙烯单封端的聚乙二醇(St- PEG)大分子单体,使其与甲基丙烯酸丁酯(BMA)在乙醇 水混合介质中进行分散共聚,得到了聚乙二醇接枝的聚甲基丙烯酸丁酯(PBMA- g -PEG)高分子微球.PBMA- g -PEG共聚物的亲溶剂 疏溶剂平衡将影响微球的形成,反应结束时,体系随BMA浓度和介质中水含量的变化呈现出4种不同的状态,透明清液、乳液、伴有沉淀或凝胶的乳液和凝胶.用透射电子显微镜(TEM)和激光光散射(LLS)对乳液体系的粒径及其形态进行了表征,表明所得接枝高分子微球形态规整具有较好的单分散性.通过控制介质中水的含量和BMA的浓度可得粒径在4 0~5 0 0nm范围的PBMA -g -PEG微球.  相似文献   

20.
Well-defined ABC block copolymers consisting of poly(ethylene oxide) monomethylene ether (MPEO) as A block, poly(styrene) (PS) as B block and poly(γ-benzyl-l-glutamate) (PBLG) as C block were synthesized by the combination of atom transfer radical polymerization (ATRP) and click reactions. The bromine-terminated diblock copolymer poly(ethylene oxide) monomethylene ether-block-poly(styrene) (MPEO-PS-Br) was prepared by ATRP of styrene initiated with macro-initiator MPEO-Br, which was prepared from the esterification of MPEO and 2-bromoisobutyryl bromide, and converted into the azido-terminated diblock copolymer MPEO-PS-N3 by simple nucleophilic substitutions in DMF in the presence of sodium azide. Propargyl-terminated PBLGs were synthesized by ring-opening polymerization of γ-benzyl-l-glutamate-N-carboxyanhydride in DMF at room temperature using propargyl amine as an initiator. ABC triblock copolymers MPEO-PS-PBLG with a wide range of number-average molecular weights from 1.55 to 3.75 × 104 and a narrow polydispersity from 1.07 to 1.10 were synthesized via the click reaction of MPEO-PS-N3 and the propargyl-terminated PBLG in the presence of CuBr and 1,1,4,7,7-pentamethyldiethylenetriamine (PMDETA) catalyst system. The structures of these ABC block copolymers and corresponding precursors were characterized by NMR, IR and GPC. The results showed that click reaction was efficient. Therefore, a facile approach was offered to synthesize ABC triblock copolymers composed of crystallizable polymer MPEO, conventional vinylic polymer PS and rod-like α-helix polypeptide PBLG.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号