Ligandless cloud point extraction of Cr(III), Pb(II), Cu(II), Ni(II), Bi(III), and Cd(II) ions in environmental samples with Tween 80 and flame atomic absorption spectrometric determination

A cloud point extraction (CPE) procedure has been developed for the determination trace amounts of Cr(III), Pb(II), Cu(II), Ni(II), Bi(III), and Cd(II) ions by using flame atomic absorption spectrometry. The proposed cloud point extraction method was based on cloud point extraction of analyte metal ions without ligand using Tween 80 as surfactant. The surfactant-rich phase was dissolved with 1.0 mL 1.0 mol L⁻¹ HNO₃ in methanol to decrease the viscosity. The analytical parameters were investigated such as pH, surfactant concentration, incubation temperature, and sample volume, etc. Accuracy of method was checked analysis by reference material and spiked samples. Developed method was applied to several matrices such as water, food and pharmaceutical samples. The detection limits of proposed method were calculated 2.8, 7.2, 0.4, 1.1, 0.8 and 1.7 μg L⁻¹ for Cr(III), Pb(II), Cu(II), Ni(II), Bi(III), and Cd(II), respectively.     

Determination of Cu, Pb, Cd, and Zn in river sediment extracts by sequential injection anodic stripping voltammetry with thin mercury film electrode

Determination of Cu, Pb, Cd and Zn was performed in sediment extracts obtained according to the three steps sequential extraction procedure proposed by the European Community Standards, Measurements and Testing Program. The metal content was determined by anodic stripping voltammetry with a thin mercury film electrode controlled by a sequential injection (SIA) system. The proposed method improved the reproducibility of conventional anodic stripping voltammetry, as well as the sample throughput, allowing analysis of 30 to 45 samples per hour. The influence of flow rate and sample volume was studied to achieve an adequate sensitivity for the leachate studied. No interferences due to adsorption of organic matter, colloids, or complexes with slow rate of dissociation were observed. The intermetallic formation of Cu-Zn was avoided by forming the mercury film in presence of Ga(III) ions in the SIA system, resulting in low consumption of reagent in comparison to flow injection or continuous flow systems. Results were in good agreement with those obtained by Induced Coupled Plasma – Atomic Emission Spectroscopy (ICP- AES). Received: 18 October 1999 / Revised: 14 December 1999 / Accepted: 19 December 1999     

A new chelating resin for preconcentration and determination of Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) by flame atomic absorption spectrometry

A new polychelatogen, AXAD-16-1,2-diphenylethanolamine, was developed by chemically modifying Amberlite XAD-16 with 1,2-diphenylethanolamine to produce an effective metal-chelating functionality for the preconcentration of Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) and their determination by flame atomic absorption spectrometry. Various physiochemical parameters that influence the quantitative preconcentration and recovery of metal were optimized by both static and dynamic techniques. The resin showed superior extraction efficiency with high-metal loading capacity values of 0.73, 0.80, 0.77, 0.87, 0.74, and 0.81 mmol/g for Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II), respectively. The system also showed rapid metal-ion extraction and stripping, with complete saturation in the sorbent phase within 15 min for all the metal ions. The optimum condition for effective metal-ion extraction was found to be a neutral pH, which is a great advantage in the preconcentration of trace metal ions from natural water samples without any chemical pretreatment of the sample. The resin also demonstrated exclusive ion selectivity toward targeted metal ions by showing greater resistivity to various complexing species and more common metal ions during analyte concentration, which ultimately led to high preconcentration factors of 700 for Cu(II); 600 for Mn(II), Ni(II), and Zn(II); and 500 for Cd(II) and Pb(II), arising from a larger sample breakthrough volume. The lower limits of metal-ion detection were 7 ng/mL for Mn(II) and Ni(II); 5 ng/mL for Cu(II), Zn(II), and Cd(II), and 10 ng/mL for Pb(II). The developed resin was successful in preconcentrating metal ions from synthetic and real water samples, multivitamin-multimineral tablets, and curry leaves (Murraya koenigii) with relative standard deviations of < or = 3.0% for all analytical measurements, which demonstrated its practical utility.     

Spectrophotometric determination of Cu(II) with sequential injection analysis

A sequential injection system, based on the reaction of Cu(II) with diethyldithiocarbamate (DDTC), was developed for the determination of Cu(II) in plant food and water samples. The extraction procedure, generally used to extract the Cu(II)–DDTC complex for subsequent analysis was eliminated in this procedure. The complex was detected spectrophotometrically in aqueous solutions at 460 nm. The physical and chemical parameters depicting the system were studied to obtain optimum conditions for sample analysis. The system developed is fully computerized and able to monitor Cu(II) in samples at seven samples per hour with a relative standard deviation of <4.50%. The calibration curve is linear from 0.5–5.0 mg/l with a detection limit of 0.2 mg/l. Interferences were reduced by introducing multiple flow reversals, to increase mixing between the reagent and sample zones, and subsequently enhance working of the masking agents (EDTA/citrate).     

Determination of Cu, Pb, Cd, and Zn in river sediment extracts by sequential injection anodic stripping voltammetry with thin mercury film electrode

Determination of Cu, Pb, Cd and Zn was performed in sediment extracts obtained according to the three steps sequential extraction procedure proposed by the European Community Standards, Measurements and Testing Program. The metal content was determined by anodic stripping voltammetry with a thin mercury film electrode controlled by a sequential injection (SIA) system. The proposed method improved the reproducibility of conventional anodic stripping voltammetry, as well as the sample throughput, allowing analysis of 30 to 45 samples per hour. The influence of flow rate and sample volume was studied to achieve an adequate sensitivity for the leachate studied. No interferences due to adsorption of organic matter, colloids, or complexes with slow rate of dissociation were observed. The intermetallic formation of Cu-Zn was avoided by forming the mercury film in presence of Ga(III) ions in the SIA system, resulting in low consumption of reagent in comparison to flow injection or continuous flow systems. Results were in good agreement with those obtained by Induced Coupled Plasma - Atomic Emission Spectroscopy (ICP-AES).     

Dynamic fractionation of trace metals in soil and sediment samples using rotating coiled column extraction and sequential injection microcolumn extraction: A comparative study

Dynamic fractionation has been recognized as an appealing alternative to conventional equilibrium-based sequential extraction procedures (SEPs) for partitioning of trace elements (TE) in environmental solid samples. This paper reports the first attempt for harmonization of flow-through dynamic fractionation using two novel methods, the so-called sequential injection microcolumn (SIMC) extraction and rotating coiled column (RCC) extraction. In SIMC extraction, a column packed with the solid sample is clustered in a sequential injection system, while in RCC, the particulate matter is retained under the action of centrifugal forces. In both methods, the leachants are continuously pumped through the solid substrates by the use of either peristaltic or syringe pumps.A five-step SEP was selected for partitioning of Cu, Pb and Zn in water soluble/exchangeable, acid-soluble, easily reducible, easily oxidizable and moderately reducible fractions from 0.2 to 0.5 g samples at an extractant flow rate of 1.0 mL min⁻¹ prior to leachate analysis by inductively coupled plasma-atomic emission spectrometry.Similarities and discrepancies between both dynamic approaches were ascertained by fractionation of TE in certified reference materials, namely, SRM 2711 Montana Soil and GBW 07311 sediment, and two real soil samples as well. Notwithstanding the different extraction conditions set by both methods, similar trends of metal distribution were in generally found. The most critical parameters for reliable assessment of mobilisable pools of TE in worse-case scenarios are the size-distribution of sample particles, the density of particles, the content of organic matter and the concentration of major elements. For reference materials and a soil rich in organic matter, the extraction in RCC results in slightly higher recoveries of environmentally relevant fractions of TE, whereas SIMC leaching is more effective for calcareous soils.     

Relationship between vegetable metal and soil-extractable metal contents by the BCR sequential extraction procedure: chemometrical interpretation of the data

The contents of heavy metals in soil and vegetable samples collected from an urban garden in Kayseri, Turkey, were investigated. Both wet- and dry-ashing methods were used for dissolving vegetable samples. A sequential extraction procedure proposed by the Commission of the European Communities, Community Bureau of Reference (now superseded by the Standards, Measurement and Testing Programme, SM&T) was applied to the soil samples to extract the metals which are present in exchangeable and acid soluble (i.e. bound to carbonates), reducible (bound to Fe/Mn oxides), and oxidisable forms (bound to organic matter and sulphides) in the soil samples. Trace metals in the soil and vegetable samples were determined using flame atomic absorption spectrometry (FAAS). The total metal contents acquired by summing of metal levels in all the sequential extraction steps were compared with pseudo-total metal levels obtained with aqua regia for all the soil samples. The recovery values obtained by proportioning the results obtained by the BCR procedure to those of the pseudo-total digestion were found to be satisfactory. The limits of detection for the elements investigated were in the range of 0.04 to 0.59?µg?mL^?1 for all the extraction stages of the BCR procedure. Similarities among the variables were identified by correlation analysis, principal component analysis and hierarchical cluster analysis. The relationship between the vegetable metal and soil-extractable metal concentrations was examined in order to evaluate the bioavailability of metals.     

Sequential injection flow system with improved sample throughput: determination of glycerol and ethanol in wines

The performance of sequential injection (SI) systems has often been criticized for its low sampling frequency. The present work describes a SI system where an injection valve and an additional pump were incorporated to enhance sample throughput rate. The proposed system was applied to the enzymatic determination of glycerol and ethanol in wines, using spectrophotometric detection and immobilized glycerol and alcohol dehydrogenases. The method proposed was applied to the determination of ethanol between 0.10 and 0.50% (v/v) and glycerol between 0.03 and 0.30 g l⁻¹. These ranges were appropriate for determination in table and port wines, since samples were diluted 50 times before introduction into the system. The results obtained from 15 wine samples were statistically comparable to those obtained by the reference methods, with good repeatability (R.S.D.<3.4%, n=10). The sampling rate was 22.5 h⁻¹, corresponding to 45 determinations per hour. This way, the time required for each determination was decreased by 30% when compared to a conventional SI system.     

Simultaneous determination of iron(II), iron(III), and titanium(IV) by flow injection analysis using kinetic spectrophotometry with Tiron

Summary Two flow injection analysis systems have been worked out for the simultaneous determination of Fe(III), Fe(II), and Ti(IV) based on the kinetic spectrophotometry with Tiron. The first system uses a silver reductor column and a single detector with two flow cells aligned in the same optical path to yield two peaks corresponding to (a) Ti(IV)-Tiron and (b) Ti(IV) plus total iron(III)-Tiron complexes. An another sample injection without the silver column yields a single peak which corresponds to Ti(IV) plus Fe(III)-Tiron complexes. With the two sample aliquot injections the system permits simultaneous determinations with throughput of 30 samples/h in the g to several tens g range of each species. The second system is a multidetection system with or without the silver reductor column using the same spectrophotometry with Tiron, in which the entrapment of the sample plug into a closed system allows its repetitive passage through a single detector. With the advantage of much simpler instrumentation, the system permits 6 samples/h to be analyzed for the three metal species with somewhat lower precisions than the first system.     

A robust multi-syringe system for process flow analysis. Part 3. Time based injection applied to the spectrophotometric determination of nickel(II) and iron speciation.

A new software-controlled time-based system for sample or reagent introduction in process flow injection analysis was developed. By using a multi-syringe burette coupled with one multi-port selection valve, the time-based injection of precise known volumes was accomplished. Characteristics and performance of the injection system were studied by injecting an indicator in a buffered carrier. Two multi-syringe time-based injection (MS-TBI) systems were implemented: first, the injection of a sample in a multiple-channel manifold where the sample would sequentially merge and react with different reagents, and second, the sequential injection of several solutions (sample and reagents) into a particular flowing stream. The first system was applied to the spectrophotometric determination of nickel(II) in diluted samples from the acidic nickel ore leaching process, by using ammonium citrate as carrier, a saturated solution of iodine as oxidizing agent and alkaline dimethylglyoxime as chromogenic reagent. The sampling frequency attained was 57 h-1. Determinations on process samples compared well at the 95% confidence level with the reference values obtained by ICP-OES. The second time-based injection system was applied to the speciation of iron. Total iron and iron(II) concentrations were separately and sequentially determined using 1,10-phenanthroline in acetic buffer medium as reagent. The developed manifold allowed the optional use of two different carrier solutions, containing or not containing ascorbic acid, for performing the separate determinations. Also, in the sequential procedure, plugs of reducing carrier were alternatively intercalated before the sample injections used for total iron determinations. Sampling frequencies of 68 injections per hour were routinely used. Accuracy was assessed by analyzing synthetic known mixtures of Fe(III) and Fe(II) standard solutions. Recoveries of 98-100.5% with a maximum relative standard deviation of 3.6% were found. Results obtained for various samples of fertilizers agreed well with those attained by the standard batch procedure.     

Polythiophene-coated Fe3O4 nanoparticles as a selective adsorbent for magnetic solid-phase extraction of silver(I), gold(III), copper(II) and palladium(II)

We have developed a fast method for sensitive extraction and determination of the metal ions silver(I), gold(III), copper(II) and palladium(II). Fe₃O₄ magnetic nanoparticles were modified with polythiophene and used for extraction the metal ions without a chelating agent. Following extraction, the ions were determined by flow injection inductively coupled plasma optical emission spectrometry. The influence of sample pH, type and volume of eluent, amount of adsorbent, sample volume and time of adsorption and desorption were optimized. Under the optimum conditions, the calibration plots are linear in the 0.75 to 100 μg L^?1 concentration range (R²?>?0.998), limits of detection in the range from 0.2 to 2.0 μg L^?1, and enhancement factors in the range from 70 to 129. Precisions, expressed as relative standard deviations, are lower than 4.2 %. The applicability of the method was demonstrated by the successful analysis of tap water, mineral water, and river water.

Extraction of Fe(III), Cu(II), Co(II), Ni(II) and Pb(II) with thenoyltrifluoroacetone using the ternary solvent system water/ethanol/methylisobutylketone

Single-phase solutions (1.72 x 10(-2)M in TTA) of water/ethanol/MIBK, when added to an excess of water, break down into two immiscible liquid layers and TTA complexes of Fe(III), Co(II), Ni(II), Cu(II) and PB(II) are extracted into the organic layer. Quantitative extractions were obtained for the five metals and separations of Fe(III) from a 1000-fold excess of Co(II), NI(II) or PB(II) are obtained. The reactions of the metal ions with TTA were studied in the single-phase solutions before the extraction step, giving useful information as to their complexation behavior.     

Asynchronous merging zones system: spectrophotometric determination of Fe(II) and Fe(III) in pharmaceutical products

An asynchronous merging zones was proposed with simultaneous introduction of the sample and of the modifier reagent, ascorbic acid in the studied case, for sequential determination of Fe(II) and Fe(III) in pharmaceutical products. The sample and reagent attained a merging point at different times owing to the use of a delay reactor in the reagent channel. By inserting a large sample and controlling the dispersion in the flow system, Fe(II) and Fe(III) were sequentially measured in the front and in the rear of the sample zone, respectively. The results obtained for Fe redox speciation in pharmaceutical products are in agreement at a 95% confidence level with those obtained with a manual spectrophotometric procedure. The analytical frequency with the proposed flow analysis system was 54 samples h(-1), i.e. 108 determinations h(-1).     

Sequential injection spectrophotometric determination of zinc(II) in pharmaceuticals based on zinc(II)–PAN in non-ionic surfactant medium

A sequential injection analysis (SIA) spectrophotometric method for the determination of trace amounts of zinc(II) with 1-(2-pyridylazo)-2-naphthol (PAN) is described. The method is based on the measurement of absorbance of the zinc(II)–PAN chelate solubilized with a non-ionic surfactant, Triton X-100, no extraction procedure is required in the proposed method, yielding a pink colored complex at pH 9.5 with absorption maximum at 553 nm. The SIA parameters that affect the signal response have been optimized in order to get the better sensitivity and minimum reagent consumption. A linear relationship between the relative peak height and concentration was obtained in the concentration range of 0.1–1.0 μg ml⁻¹. The limit of detection (LOD, defined as 3σ) and limit of quantification (LOQ, defined as 10σ) were 0.02 and 0.06 μg ml⁻¹, respectively. The sample throughput about 40 samples/h was obtained. The repeatability were 1.32 and 1.24% (n = 10) for 0.1 and 0.5 μg ml⁻¹, respectively. The proposed method was successfully applied to the assay of zinc(II) in three samples of multivitamin tablets. The results were found to be in good agreement with those obtained by flame atomic absorption spectrophotometric method and with the claimed values by the manufactures. The t-test showed no significant difference at 95% confidence level.     

Application of Short Sequential Extraction Procedure（SSEP） for the Determination of Zn, Cu, and Cd Contents in Riverbed Sludge in Hejiagou, Harbin, China

IntroductionThe environment is contaminated by high concen-trations of metals from different sources such as conta-minated soils[1—10], sediments[11—15], and sewage orindustrial sludge[16—20]. However, there has been noreport on the determination of he…     

Selective enrichment of U(VI), Th(IV) and La(III) from high acidic streams using a new chelating ion-exchange polymeric matrix

An off-line extraction chromatographic technique has been developed using Amberlite XAD-16 (AXAD-16)-N,N-dihexylcarbamoylmethyl phosphonic acid, as the stationary phase for the extraction of uranium, thorium and lanthanum from nuclear spent fuels as well as from geological and natural water resources. The chemical modifications of the polymeric matrix were monitored using FT-IR spectroscopy, CHNPS elemental analysis and also by thermo gravimetric analysis for water regain measurements. Various physio-chemical parameters influencing the quantitative metal ion extraction by the resin phase were optimized by both static and dynamic methods. The developed resin matrix showed good distribution ratio values under wide concentrations of acidity and pH conditions. Moreover, the sequential separation of analytes is also possible at sample pH 6.5. Also, the polymeric matrix showed superior metal sorption capacities and rapid metal exchange kinetics with a high sample flow rate value of 26 cm³ min⁻¹ for all the three analytes. Thus, reducing the time of analyte extraction from large number of samples anticipated in nuclear waste management programs. The quantitative metal ion recovery of >99.8% was effected with 0.5 M (NH₄)₂CO₃ solution. The method was highly sensitive with lower limits of detections to be 10, 20 and 15 ng cm⁻³ for U(VI), Th(IV) and La(III), respectively, with a better pre-concentration values of 333 for U(VI) and Th(IV) and 400 for La(III), respectively paving way for its applicability in pre-concentrating trace analytes from large sample volumes. The analytical data were within 4.2% R.S.D. reflecting the reproducibility and reliability of the developed method.     

Immersed single-drop microextraction interfaced with sequential injection analysis for determination of Cr(VI) in natural waters by electrothermal-atomic absorption spectrometry

Single-drop microextraction (SDME) and sequential injection analysis have been hyphenated for ultratrace metal determination by Electrothermal-Atomic Absorption Spectrometry (ETAAS). The novel method was targeted on extraction of the Cr(VI)-APDC chelate and encompasses the potential of SDME as a miniaturized and virtually solvent-free preconcentration technique, the ability of sequential injection analysis to handle samples and the versatility of furnace autosamplers for introducing microliter samples in ETAAS.     

Two-parameter determination in vinegar by a flow injection-pervaporation system

A flow injection method (FI) for the sequential determination of ethanol and acetic acid in vinegar is reported. The determination of ethanol is based on the oxidation of the pervaporated ethanol by K2Cr2O7. The acetic acid is determined by an acid-base reaction with Thymol Blue as the indicator. Both reactions are monitored photometrically at 600 nm using a single detector. Optimisation studies and assessment of the sequential Fl method are also reported. The linear determination range is 0-12% v/v for ethanol and 0-10% (grams of acetic acid in 100 ml) for acetic acid. The sample throughput of the sequential manifold is seven per hour. The new method was applied to vinegar samples and the results obtained were in excellent agreement with those from reference methods used in Spain.     

Cloud point extraction and simultaneous spectrophotometric determination of V(V), Co(II) and Cu(II) ions in water samples by 5-Br-PADAP using partial least squares regression

In this work, a new method has been proposed to simultaneously determine V(V), Co(II) and Cu(II) ions from aqueous solution by spectrophotometry after cloud point extraction using partial least squares regression (PLS). The metal ions in 10 ml of aqueous solution (containing 0.2 M sodium acetate buffer solution, pH 3.5) were formed complexes with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP). Then, Triton X-114 (2 %, v/v) was added to the solution. By increasing the temperature of the solution up to 55 °C, a phase separation occurred. After centrifugation at 3,000 rpm for 10 min, the surfactant-rich phase was dissolved and diluted to 0.5 mL with ethanol. The metal ions were then determined using spectrophotometry. At these optimal extraction and operating conditions, linearity was obeyed in the range 7–300, 3–100 and 15–700 ng mL^?1 of V(V), Co(II) and Cu(II), with the detection limit of 2.2, 1.0 and 4.5 ng mL^?1, respectively. The relative predictive error for the simultaneous determination of 15 test samples of different concentrations of V(V), Co(II) and Cu(II) was 3.28, 3.64 and 4.04 %, respectively. The root mean square error of prediction for applying the PLS method to 15 synthetic samples in the linear ranges of these metal ions was 3.4, 1.6 and 18.1 ng mL^?1. The interference effect of some anions and cations was also tested. The proposed method has been applied successfully to the simultaneous determination of V(V), Co(II) and Cu(II) ions in real matrix samples with the recoveries of 96.75–104.80 %.     

Simultaneous Voltammetric Determination of Zn(II), Pb(II), Cu(II), and Hg(II) in Ethanol Fuel Using an Organofunctionalized Modified Graphite‐Polyurethane Composite Disposable Screen‐Printed Device

A disposable screen‐printed device containing working, auxiliary, and reference electrodes is proposed for the simultaneous voltammetric determination of Zn(II), Pb(II), Cu(II), and Hg(II) in ethanol fuel. The working electrode was printed using an ink modified with 2‐benzothiazole‐2‐thiol organofunctionalized SBA‐15 silica, in order to increase sensitivity. The performance of this electrode was compared with that of bare and SBA‐15‐modified electrodes. After optimizing the experimental parameters, the device was applied in determination of the analytes in commercial ethanol fuel samples, using 0.10 mol L^?1 KCl/ethanol ratios of 30 : 70 (v/v), with [H⁺]=10^?5 mol L^?1. After 5 min of preconcentration at ? 1.3 V (vs. pseudo‐Ag/AgCl), four well‐resolved signals were obtained, enabling simultaneous determination of the four analytes using a differential pulse anodic stripping voltammetry (DPASV) procedure. The limits of detection were 0.30, 0.065, 0.030, and 0.046 µmol L^?1 for Zn(II), Pb(II), Cu(II), and Hg(II), respectively. The results of these analyses were in agreement with those obtained using graphite furnace atomic absorption spectroscopy (GFAAS) for Pb(II), Cu(II), and Hg(II), and high‐resolution continuum source flame atomic absorption spectrometry (HR‐CS‐FAAS) for Zn²⁺, at a 95 % confidence level. Analytes originally present in the samples could be detected, and the interference of some cations and anions was evaluated.