相位调制信号对窄线宽光纤放大器线宽特性和受激布里渊散射阈值的影响

高功率窄线宽光纤放大器的输出功率主要受限于受激布里渊散射(SBS)效应,通过相位调制进行线宽展宽可以有效抑制SBS效应.基于窄线宽光纤放大器中的SBS动力学模型,研究了正弦信号、白噪声信号和伪随机编码信号(PRBS)对窄线宽光纤放大器光谱特性与SBS阈值的影响.研究发现,采用不同信号进行相位调制时,调制频率和调制深度等参数对调制后激光光谱的谱线间隔、谱线数目与光谱平整度的影响存在较大差异,进而影响放大器的线宽特性和SBS阈值.通过对比分析,给出了调制信号的类型选择和参数优化原则,能够为窄线宽光纤放大器的相位调制系统设计提供参考.     

基于微波电光调制的布里渊光时域分析传感器

针对布里渊光时域分析分布式传感原理和受激布里渊散射的特点,应用微波电光调制分布反馈式半导体激光器产生频移可调的探测光,和传感光纤中相反方向传输的脉冲激励光进行受激布里渊散射作用,当探测光和激励光的频率差在布里渊频移附近时,频移探测光和激励光产生受激布里渊散射,通过改变探测光的频移值,检测探测光功率信号,可得到沿光纤各处的布里渊频移,再利用布里渊频移和应变（或温度）的关系,计算得到沿光纤分布的传感量。设计了基于微波电光调制的布里渊光时域分析传感器实验系统,实现了25km的分布式温度传感,达到5m的空间分辨力和3℃的温度分辨力。     

Effect of Brillouin slow light on distributed Brillouin fiber sensors

The effect of Brillouin slow light on distributed Brillouin fiber sensors (DBFSs) is studied. We demonstrate Brillouin slow light for a 1.2 ns pulse with peak powers (PS) from 3.3 to 56.2 mW on depletion of the pump power (PP) ranging from 1.3 to 83.2 mW in conventional optical fibers (SMF-28). Experiments show that, when pump power depletion is not negligible, for a given PP the Brillouin gain and delay time of a pulse decrease when PS increases in a long (> or =10 km) sensing fiber. The optimum pump beam depletion resulting from strong interaction of the pump and the probe in the fiber provides accurate temperature and strain information at a high spatial resolution. Our study reveals that at low PP the spatial resolution error caused by the pulse delay for a DBFS with centimeter spatial resolution is less than 5% of the pulse length.     

基于双向拉曼放大的布里渊光时域分析系统

报道了一种基于双向拉曼放大的布里渊光时域分析系统(Brillouin optical time domain analyzer,BOTDA).利用双向拉曼抽运对信号光进行拉曼放大以补偿光纤损耗及布里渊抽运波的消耗,从而使光纤后端的测量分辨率得到改善,测量分辨率在整段传感光纤趋于一致,同时避免了调制不稳定性引起的频谱扩展,克服了传统BOTDA存在的信号强度指数下降的弊端,使传感精度得到进一步提高.实验实现了50 km传感距离, 温度分辨率达0.6 ℃,空间分辨率为50 m.实验测量并分析了基于双向拉曼放大的BOTDA信噪比和光功率分布特性. 关键词： 分布式光纤传感 受激拉曼放大 布里渊增益 布里渊光时域分析     

Enhanced four-wave mixing in a high-finesse highly nonlinear fiber Fabry-Perot resonator

We have achieved a four-wave mixing process in a high-finesse highly nonlinear fiber Fabry-Perot resonator, where the amplified signal and idler were enhanced in transmission by 6 dB and 10 dB respectively comparing with those in a single fiber. We used a 6 m long low-loss Fabry-Perot resonator with two high-reflectivity fiber Bragg gratings written directly into a highly nonlinear fiber provided by Sumitomo Electric Inc., where the minimised intracavity loss resulted in the finesse in excess of 100. The resonator length was locked for 30 min by means of a modified Pound-Drever-Hall technique. The maximum intracavity power was increased by 14.3 dB by increasing the stimulated Brillouin scattering threshold with periodic phase modulation by a pseudo-random bit sequence, with length matching that of the cavity.     

一种基于暗脉冲光布里渊时域分析仪的延长传感距离的方法

基于暗脉冲的布里渊时域分析仪系统中泵浦光和探测光的功率较高,相互作用强烈,严重限制了系统的有效传感距离。而现有的系统众多采用利用多段具有不同布里渊散射频率的光纤相互连接延长传感距离的方法,降低每段光纤上的受激布里渊散射效应,延长有效传感距离,但这种方案会增加的系统的复杂度,影响实际应用.本文提出一种简单的暗脉冲光布里渊时域分析仪的结构,可在满足高空间分辨率的条件下,有效的延长系统的传感距离,取代通常的利用多段具有不同布里渊散射频率的光纤相互连接延长传感距离的方法.利用基于光抑制载波的技术,产生具有两个边带的斯托克斯光.斯托克斯光的两个边带和泵浦光相互作用,同时激发布里渊散射增益和衰减效应,在接收端利用两者接收信号的差,可抵消原有暗脉冲泵浦信号中准连续光对传感距离的影响,从而有效地延长系统的传感距离,并利用数值仿真的方法验证了此方法的有效性.     

应变梯度对布里渊光时域反射计测量精度的影响

基于脉冲抽运的布里渊光时域反射计技术具有米数量级的空间分辩力。为了分析在其空间分辨力范围内的应变梯度增加对布里渊谱测量的影响,建立了后向布里渊散射谱与应变梯度的函数关系。数值分析结果表明应变梯度增大,不仅使布里渊频移随之线性增大,也会使后向布里渊散射谱峰值非线性降低,谱峰变得平坦。空间分辨力10m的100με／m应变梯度相对于零应变梯度,引起的布里渊频移测量误差增加2．04倍。传感光纤固定于悬臂梁上以模拟不同应变梯度,采用对频宽小于1MHz的激光脉冲调制和基于相干平衡检测的布里渊光时域反射计系统,实验测得了沿传感光纤的后向布里渊散射谱数据和应变分布。布里渊谱数据经最小二乘法拟合后,得到的不同应亦梯度的谱曲线变化与理论分析相吻合。     

Impact of Brillouin amplification on the spatial resolution of noise-correlated Brillouin optical reflectometry

To obtain high spatial resolution over a long sensing distance in Brillouin optical correlation domain reflectometry(BOCDR), a broad laser spectrum and high pump power are used to improve the signal-to-noise ratio(SNR). In this Letter, we use a noise-modulated laser to study the variation of the Brillouin spectrum bandwidth and its impact on the coherent length of BOCDR quantitatively. The result shows that the best spatial resolution(lowest coherent length) is achieved by the lowest pump power with the highest noise-modulation spectrum. Temperature-induced changes in the Brillouin frequency shift along a 253.1 m fiber are demonstrated with a 19 cm spatial resolution.     

Distributed strain measurement using a tellurite glass fiber with Brillouin optical correlation-domain reflectometry

A tellurite glass fiber with a high Brillouin gain was employed for distributed strain measurement with Brillouin optical correlation-domain reflectometry (BOCDR). First, the spatial resolution of BOCDR was evaluated using the tellurite fiber. With the high Brillouin gain of the fiber, it was confirmed clearly in the experiment that the spatial resolution is limited by the Rayleigh scattering-induced noise. Then, the dependence of the Brillouin frequency shift (BFS) on strain in the tellurite fiber was investigated, showing a negative dependence with a coefficient of −0.023 MHz/με. Using this tellurite fiber, the distribution of the BFS around a 1-cm strain-applied section was successfully measured with BOCDR of a nominal spatial resolution of 6 mm.     

Brillouin power spectrum analysis for partially uniformly strained optical fiber

Due to the restriction of the spatial resolution, about 1 m for current commercially available system, strain distribution measured by Brillouin optical time domain reflectometer (BOTDR) is slightly different from the actual one. In this paper, the equation of the Brillouin power spectrum for partially uniformly strained fiber within the spatial resolution is theoretically derived. Based on the derived results, investigation has been made on the shape characteristics of the superposed Brillouin power spectrum, as well as the dependence of the calculated strain of BOTDR on the actual strain of the fiber. It was found that the difference between the calculated strain and the actual strain depends mainly on the strain value of the fiber and the strained length within the spatial resolution for the given distributed sensing system.     

High-repetition-rate distributed Brillouin sensor based on optical correlation-domain analysis with differential frequency modulation

A kind of high-repetition-rate distributed Brillouin sensor is proposed and experimentally demonstrated based on optical correlation-domain analysis with differential frequency modulation, where the optical frequencies of the pump and the probe waves are modulated at slightly different RFs so that the temporal position of the measurement is continuously and repeatedly swept along a fiber under test. A distribution map of Brillouin frequency variation along a 100 m optical fiber is acquired at a repetition rate of 20 Hz with an accuracy of ±2.5 MHz and a spatial resolution of about 80 cm.     

基于超长环形激光器泵浦的94 km布里渊分布式传感系统

首次将超长光纤环形激光器的光放大应用于布里渊光时域分析(BOTDA)传感系统,以延伸传感距离。 通过对布里渊泵浦消耗、 拉曼泵浦相对强度噪声(RIN)转移的抑制及拉曼泵浦功率分布的优化,基于对布里渊增益谱分析的原理在94 km的传感距离上实现了3 m空间分辨率,以及全程28 με/1.4 ℃应变/温度精度。     

57-km single-ended spontaneous Brillouin-based distributed fiber temperature sensor using microwave coherent detection

We present a novel technique for performing single-ended distributed fiber temperature measurements by use of microwave heterodyne detection of spontaneous Brillouin scattering. Brillouin frequency-shift measurements were obtained for a sensing length of 57 km, with a spatial resolution of 20 m. The rms error in frequency measurements at the far end of the sensing fiber was less than 3 MHz, and the overall frequency dependence on temperature was 1.07+/-0.06 MHz/K.     

布里渊动态光栅原理及其在光纤传感中的应用

自从2007年布里渊动态光栅被首次提出用于实现光存储以来,该技术得到了国际上的广泛关注和研究.布里渊动态光栅本质上是由相干声波场激发的折射率光栅,一般情况下两束抽运光(频率差等于光纤的布里渊频移)以相同的偏振态从光纤两端注入到光纤中,通过受激布里渊散射效应激发出相干声波场,即形成布里渊动态光栅.光纤布里渊动态光栅因具有全光产生、参数灵活可控的优点,已被广泛研究应用于光纤传感、光纤特性表征、光存储、全光信号处理、微波光子学和高精度光谱分析等.本文分析布里渊动态光栅产生和探测原理,重点探讨在高性能分布式光纤传感上的应用,这些应用包括高灵敏度温度和应变分布式传感、温度和应变同时解调、分布式横向压力传感、分布式静压力(气压或液压)传感、高空间分辨率分布式传感和高精度光谱分析.     

提高布里渊光时域反射应变仪测量空间分辨力的等效脉冲光拟合法

由于探测光脉冲宽度受到限制,布里渊光时域反射仪(BOTDR)在对光纤上的应变进行分布式测量时,空间分辨力只能达到1 m。针对布里渊光时域反射仪单次采样接收背向布里渊散射信号(BBS)需要一定的时间,提出了基于等效脉冲光的多洛仑兹拟合法以提高其应变测量的空间分辨力。该方法将探测光脉冲在布里渊光时域反射仪完成单次采样所需的时间上进行积分,将积分函数作为等效脉冲光的表达式,再根据等效脉冲光的形状将布里渊光时域反射仪接收到的背向布里渊散射谱(BBS)细分,并对它进行多洛仑兹迭代拟合,准确求得每个细分布里渊散射谱的中心频率,进而利用光纤中布里渊频移与应变的对应关系,得到光纤中与细分布里渊散射谱对应的细分光纤单元上的应变情况。实验结果表明,利用这种方法,可使布里渊光时域反射仪应变测量的空间分辨力提高至0.05 m。     

Distributed strain measurement with millimeter-order spatial resolution based on Brillouin optical correlation domain analysis

Distributed strain sensing with millimeter-order spatial resolution is demonstrated in optical fibers based on Brillouin optical correlation domain analysis. A novel beat lock-in detection scheme is introduced to suppress background noises coming from the reflection of Brillouin pump waves. The Brillouin frequency shifts of 3 mm fiber sections are successfully measured with a theoretical spatial resolution of 1.6 mm.     

Spatial Resolution Enhancement in BOTDR by Spectrum Separation Method

BOTDR (Brillouin optical-fiber time domain reflectometry) is a promising technique for measuring the strain distribution along an optical fiber which can be used for diagnosing civil structures. However, there is a trade-off between the spatial and the frequency resolutions, and its practical spatial resolution is limited to about 1 m; to date the application scope has been restricted. In order to enhance the spatial resolution without decreasing the measurement accuracy, we intentionally introduce two kinds of strain within the spatial resolution length determined by the optical pulse width, which results in Brillouin gain spectrum separation. In this paper, we describe the theoretical analysis of the spectrum separation method together with experimental verification, where a spatial resolution of 0.5 m is demonstrated. We further propose a new parabolic data fitting method especially effective in the spectrum separation method.     

Long-range simplex-coded BOTDA sensor over 120 km distance employing optical preamplification

In this Letter, we combine the use of optical preamplification at the receiver and optical pulse coding techniques with an optimized modulation format to effectively extend the sensing range of Brillouin optical time-domain analysis (BOTDA) sensors. Combining a return-to-zero modulation format with 25% duty cycle and linear gain preamplification allows for temperature and strain measurements over 120 km of standard single-mode fiber with 3 m spatial resolution and an rms strain-temperature accuracy of 3.1 °C/60 με respectively.     

波分复用串联的布里渊散射分布式光纤传感器

在一定分辨率和响应时间要求下，应用波分复用技术来串联布里渊散射分布式光纤传感器，解决了同时进行传感和通信存在的信号干扰.具体是采用波分复用来隔离传感光信号与通信光信号，同时应用光相干外差接收来分离传感与通信之间的电信号频谱.实现了两台布里渊散射分布式光纤传感器之间的串联，单台传感器的传感距离为25 km，串联后达到50 km.     

光脉冲编码对基于拉曼放大的布里渊光时域分析系统的影响

报道了光脉冲编码对基于拉曼放大的布里渊光时域分析系统(BOTDA)的影响. 实验表明,光脉冲编码能够在保证较高空间分辨率的同时减小布里渊频移的不确定性. 实验实现了49.6 km传感距离, 在整段传感光纤上温度分辨率1 ℃,空间分辨率2.5 m. 本文实验测量并分析了系统的信噪比和光功率分布特性. 关键词： 分布式光纤传感 受激拉曼散射 布里渊增益 布里渊光时域分析系统(BOTDA)