Fabrication and properties of novel low-melting glasses in the ternary system ZnO-Sb2O3-P2O5

Glasses in the ternary system ZnO-Sb₂O₃-P₂O₅ were investigated as potential alternatives to lead based glasses for low temperature applications. The glass-forming region of ZnO-Sb₂O₃-P₂O₅ system has been determined. Structure and properties of the glasses with the composition (60 − x)ZnO-xSb₂O₃-40P₂O₅ were characterized by infrared spectra (IR), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results of IR indicated the role of Sb³⁺ as participant in glass network structure, which was supported by the monotonic and remarkable increase of density (ρ) and molar volume (V_M) with increasing Sb₂O₃ content. Glass transition temperature (T_g) and thermal stability decreased, and coefficient of thermal expansion (α) increased with the substitution of Sb₂O₃ for ZnO in the range of 0-50 mol%. XRD pattern of the heat treated glass containing 30 mol% Sb₂O₃ indicated that the structure of antimony-phosphate becomes dominant. The improved water durability of these glasses is consistent with the replacement of easily hydrated phosphate chains by corrosion resistant P-O-Sb bonds. The glasses containing ?30 mol% Sb₂O₃ possess lower T_g (<400 °C) and better water durability, which could be alternatives to lead based glasses for practical applications with further composition improvement.     

Synthesis and physical properties of glasses in the Sb2O3-PbCl2-MoO3 system

Lead chloroantimonite glasses form stable binary glasses that may accommodate numerous oxides or halides as a third component. Molybdenum trioxide is a glass progenitor leading to molybdate glasses. Ternary glasses have been synthesized and studied in the Sb₂O₃-PbCl₂-MoO₃ system. Compositional limits of glass formation are reported and two series of glass samples have been prepared corresponding to the general formulas: (90 − x)Sb₂O₃-xPbCl₂-10MoO₃ and (90 − x)Sb₂O₃-xMoO₃-10PbCl₂. Glass transition temperature is close to 290 °C at high Sb₂O₃ content and decreases as antimony oxide is substituted by MoO₃ or PbCl₂. Position, width and intensity of crystallization peak suggest that devitrification rate is small in some composition ranges. The evolution of density, thermal expansion, refractive index and microhardness has been studied as a function of composition parameter x. Deviations from linearity are observed. They suggest structural changes in the case of the MoO₃/Sb₂O₃ substitution while it appears that molar volume increases linearly versus lead content in the other series of glasses. Refractive index is close to 2.04. Optical transmission ranges from 550 nm in the visible spectrum to 5.5 μm in the infrared. It is limited by extrinsic absorption bands arising from hydroxyls and silicon impurities. Young's, bulk and shear moduli have been measured for the two series of samples.     

Electron spin resonance and magnetic studies on CaO-SiO2-P2O5-Na2O-Fe2O3 glasses

Room temperature electron spin resonance (ESR) spectra and temperature dependent magnetic susceptibility measurements have been performed to investigate the effect of iron ions in 41CaO · (52 − x)SiO₂ · 4P₂O₅ · xFe₂O₃ · 3Na₂O (2 ? x ? 10 mol%) glasses. The ESR spectra of the glass exhibited the absorptions centered at g ≈ 2.1 and g ≈ 4.3. The variation of the intensity and linewidth of these absorption lines with composition has been interpreted in terms of variation in the concentration of the Fe²⁺ and Fe³⁺ in the glass and the interaction between the iron ions. The magnetic susceptibility data were used to obtain information on the relative concentration and interaction between the iron ions in the glass.     

Temperature-assisted electrical poling of TeO2-Bi2O3-ZnO glasses for non-linear optical applications

The suitability for effective thermal poling of the ternary tellurite glasses with the compositions (100 − 2x)TeO₂-xBi₂O₃-xZnO (x = 5, 10 and 15, in molar percentage) for the second harmonic generation (SHG) was analyzed. The glass transitions and crystallization temperatures were studied via differential thermal analysis. The structural properties of the annealed glasses and furtherly heat-treated samples were probed by extended X-ray absorption fine structure (EXAFS) spectroscopy. Thermal poling of the glasses was undertaken conventionally at various temperatures close to the glass transition temperature under high vacuum and the second harmonic generated signals were compared. A new technique of two stage poling was tested for comparison. The non-linear second harmonic signal of the poled glasses was analyzed using the Maker-fringe technique and it was found that the two stage poling enhanced the non-linear efficiency when compared to the conventionally poled samples.     

Effects of Nb2O5 Replacement by Er2O3 on elastic and structural properties of 75TeO2-(10 − x)Nb2O5-15ZnO-(x)Er2O3 glass

Tellurite 75TeO₂-(10 − x)Nb₂O₅-15ZnO-(x)Er₂O₃; (x = 0.0-2.5 mol%) glass system with concurrent reduction of Nb₂O₅ and Er₂O₃ addition have been prepared by melt-quenching method. Elastic properties together with structural properties of the glasses were investigated by measuring both longitudinal and shear velocities using the pulse-echo-overlap technique at 5 MHz and Fourier Transform Infrared (FTIR) spectroscopy, respectively. Shear velocity, shear modulus, Young's modulus and Debye temperature were observed to initially decrease at x = 0.5 mol% but remained constant between x = 1.0 mol% to x = 2.0 mol%, before increasing back with Er₂O₃ addition at x = 2.5 mol%. The initial drop in shear velocity and related elastic moduli observed at x = 0.5 mol% were suggested to be due to weakening of glass network rigidity as a result of increase in non-bridging oxygen (NBO) ions as a consequence of Nb₂O₅ reduction. The near constant values of shear velocity, elastic moduli, Debye temperature, hardness and Poisson's ratio between x = 0.5 mol% to x = 2.0 mol% were suggested to be due to competition between bridging oxygen (BO) and NBO ions in the glass network as Er₂O₃ gradually compensated for Nb₂O₅. Further addition of Er₂O₃ (x > 2.0 mol%) seems to further reduce NBO leading to improved rigidity of the glass network causing a large increase of ultrasonic velocity (v_L and v_S) and related elastic moduli at x = 2.5 mol%. FTIR analysis on NbO₆ octahedral, TeO₄ trigonal bipyramid (tbp) and TeO₃ trigonal pyramid (tp) absorption peaks confirmed the initial formation of NBO ions at x = 0.5 mol% followed by NBO/BO competition at x = 0.5-2.0 mol%. Appearance of ZnO₄ tetrahedra and increase in intensity of TeO₄ tbp absorption peaks at x = 2.0 mol% and x = 2.5 mol% indicate increase in formation of BO.     

Thermal and some physical properties of glasses in the La2O3−CaO−B2O3 ternary system

Glasses in the La₂O₃−CaO−B₂O₃ ternary system were studied. The glass forming range as determined by the appearance of the annealed cast was found to match previously published findings. Clear glasses were formed in the composition range of 5.7−19.1 mol% La₂O₃ with constant B₂O₃ content of 71.4 mol%, and in glasses of constant La₂O₃:CaO ratio of 1:4 with B₂O₃ content in the range of 71.4-55.0 mol%. The non-linear optical crystalline phase La₂Ca₂B₁₀O₁₉ was crystallized from the clear glasses after heat treatments, as determined by powder XRD. Two types of the LaBO₃ crystalline phases were detected in the partially and the fully crystallized glass compositions outside the glass forming range. Data are reported for the glass transition temperature (T_g), dilatometric softening point (T_d), linear coefficient of expansion (α), onset crystallization temperature (T_x), exothermal peak temperature (T_P), density (ρ) and index of refraction (n_D) in the clear glasses.     

Thermodynamical miscibility in 0.8[xB2O3-(1 − x)P2O5]-0.2K2O glasses

The thermodynamical miscibility in 0.8[xB₂O₃-(1 − x)P₂O₅]-0.2K₂O glasses has been studied by measuring the glass transition temperature and the mixing enthalpy. Measurements have been performed by differential scanning calorimeter and hydrofluoric acid solution calorimetry at 298 K. The enthalpies of mixing are significantly negative over the whole range of composition. The results are discussed in terms of intermolecular associations.     

Effect of P2O5 content in two series of soda lime phosphosilicate glasses on structure and properties - Part I: NMR

The effect of the variation in phosphate (P₂O₅) content on the structure of two series of bioactive glasses in the quaternary system SiO₂-Na₂O-CaO-P₂O₅ was studied. The first series (I) was a simple substitution of P₂O₅ for SiO₂ keeping the Na₂O:CaO ratio fixed (1.00:0.87). The second series was designed to ensure charge neutrality in the orthophosphate , therefore as P₂O₅ was added the Na₂O and CaO content was varied to provide sufficient Na⁺ and Ca²⁺ cations to charge balance the orthophosphate present. The glass network connectivity (NC) was calculated for each glass and a modification for the presence of a separate P₂O₅ phase was included (NC′). ³¹P and ²⁹Si magic-angle-spinning nuclear magnetic resonance (MAS-NMR) spectroscopy was performed on glass series I and II to determine the structural units present and their relation to glass properties. ³¹P MAS-NMR spectra of series I resulted in a broad resonance around 9 ppm corresponding to orthophosphate in an amorphous environment. The 9.25 mol% P₂O₅ glass shown to be partially crystalline by X-ray diffraction was heat treated, and the ³¹P MAS-NMR spectrum showed a sharp peak around 3 ppm corresponding to calcium orthophosphate or sodium pyrophosphate and overlapping broader peaks at 8.5, 10.5 and 14 ppm possibly corresponding to two mixed calcium-sodium orthophosphate phases and amorphous sodium orthophosphate respectively. ³¹P MAS-NMR spectra of series II resulted in a broad resonance around 10.5 ppm corresponding to orthophosphate in an amorphous environment. ²⁹Si MAS-NMR spectra of glasses from series I showed a shift in the resonance peak from around −78 to −86 ppm indicating an increase in Q³ species in the glass and a reduction in Q² with phosphate addition confirming the presence of orthophosphate. The heat treated sample showed a sharp ²⁹Si-NMR resonance at −88 ppm, indicating a crystalline Q² six-membered combeite (Na₂O · 2CaO · 3SiO₂) silicate-type phase, which was confirmed by powder X-ray diffraction. ²⁹Si MAS-NMR spectra of glasses from series II showed no shift in the resonance at around −78 ppm across the series, confirming an orthophosphate environment.     

Synthesis and characterization of calcium phosphate based bioactive quaternary P2O5-CaO-Na2O-K2O glasses

Calcium phosphate based bioactive quaternary glass systems P₂O₅-CaO-Na₂O-K₂O were prepared by melt growth technique. Glasses were prepared in five different compositions by fixing P₂O₅ at 47 mol% and CaO at 30.5 mol% and by varying the K₂O and Na₂O concentrations. The structural properties of the glasses are analyzed using X-ray diffraction (XRD) studies and scanning electron microscopy (SEM) studies; and the composition of the glasses are studied using energy dispersive X-ray spectrum (EDS). The microhardness of the glass systems are studied by Vickers hardness measurements and the bioactivity of the glasses are studied using in vitro study. The thermal properties have been examined by means of thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The ultrasonic velocity measurements show that the addition of K₂O contents produces non-bridging oxygen ion and hence weaken of the glass structure. The weakening of the glass structure reduces the ultrasonic velocity and hence an increase in attenuation.     

Spectral properties of PbO-P2O5 glasses

The optical absorption spectra of xPbO-(100 − x) P₂O₅ glasses where x = 5, 10, 15, 20, 25, and 30 is reported. The spectral absorption of these glasses was measured in the spectral range 300-900 nm at room temperature. Optical absorption spectra show that the absorption edge has a tail extending towards lower energies. The edge shifts nearly linearly towards higher energies with increasing PbO content. The degree of the edge shift was found to depend on the PbO content and is mostly related to the structural rearrangement and the relative concentrations of the glass basic units. The optical energy gap increases, from 2.55 to 3.05 eV by increasing PbO content from 5 to 30 mol%. The width of the localized states is decreased by increasing PbO content.     

Dielectric analysis of tungsten-phosphoniobate 20A2O-30WO3 -10Nb2O5 -40P2O5 (A = Li, Na) glass-ceramics

New phosphate glasses of the quaternary system A₂O-Nb₂O₅-WO₃-P₂O₅, where X = Li and Na were prepared by the melt-quenching method. The introduction of WO₃ in the glass composition was based on the proposal of analysing the effect of the diminishing of the molar amount of the alkaline oxide and thus decreasing the molar ratio between network modifiers and network formers (M/F).In the present work we present the preparation of 20A₂O-30WO₃-10Nb₂O₅-40P₂O₅ (A = Li, Na) transparent glasses. These glasses were heat-treated in air, at 550 °C and 650 °C for 4 h. The structure of the obtained samples was studied by X-ray powder diffraction (XRD) and Raman spectroscopy and the morphology by scanning electron microscopy (SEM). The dc (σ_dc), ac (σ_ac) conductivity and dielectric spectroscopy measurements were performed in the function of the temperature and were related with the structural changes of the glass structures.     

The glass transition temperature and infrared absorption spectra of: (70−x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Glasses of the system: (70−x) TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by melt quench technique. Dependencies of their glass transition temperatures (T_g) and infrared (IR) absorption spectra on composition were investigated. It is found that the gradual replacement of oxides, TeO₂ by Li₂O, decreases the glass transition temperature and increases the fragility of the glasses. Also, IR spectra revealed broad weak and strong absorption bands in the investigated range of wave numbers from 4000 to 400 cm⁻¹. These bands were assigned to their corresponding bond modes of vibration with relation to the glass structure.     

Optical Properties of Bi2O3-TeO2-B2O3 Glasses

Glasses of the Bi₂O₃-TeO₂-B₂O₃ ternary system were developed and their linear and nonlinear optical properties were investigated. The absorption edges of these glasses were found to be 367-384 nm with a good transmittance in visible wavelength, although they exhibit the refractive indices as high as 1.98-2.12 at 633 nm. The absorption edges are quite steep and they are analyzed by the Urbach theory. The obtained Urbach energies of these glasses are 73-79 meV which are comparable to silica glasses. The high refractive index and its glass composition dependency are discussed according to the basics of the electronic polarizability and optical basicity. The high third order nonlinear susceptibility χ⁽³⁾ = 2.0 × 10^− 12 esu at 800 nm was also obtained in the 36Bi₂O₃-18TeO₂-46B₂O₃ glass.     

Structure and electrical conductivity of new Li2O-CeO2-B2O3 glasses

Fourier transformation infrared spectra, density and DC electrical conductivity of 30Li₂O · xCeO₂⋅(70 − x)B₂O₃ glasses, where x ranged between 0 and 15 mol%, have been investigated. The results suggested that CeO₂ plays the role of network modifier up to 7.5 mol%. At higher concentrations it plays a dual role; where most of ceria plays the role of network former. The density was observed to increase with increasing CeO₂ content. The effect on density of the oxides in the glasses investigated is in the succession: B₂O₃ < Li₂O < CeO₂. Most of CeO₂ content was found to be associated with B₂O₃ network to convert BO₃ into B O₄⁻ units. The contribution of Li⁺ ions in the conduction process is much more than that due to small polarons. The conductivity of the glasses is mostly controlled by the Li⁺ ions concentration rather than the activation energy for CeO₂ > 5 mol%. Lower than 5 mol% CeO₂ the conductivity is controlled by both factors. The dependence of W on BO₄⁻ content supports the idea of ionic conduction in these glasses.     

A sharp thermally reversing window in As45Te55−xIx chalcohalide glasses revealed by alternating differential scanning calorimetry and photo thermal deflection studies

The composition dependence of different thermal parameters such as glass transition temperature, non-reversing enthalpy, thermal diffusivity etc., of bulk As₄₅Te_55−xI_x chalcohalide glasses (3 ? x ? 10), has been evaluated using the temperature modulated Alternating Differential Scanning Calorimetry (ADSC) and Photo Thermal Deflection (PTD) studies. It is found that there is not much variation in the glass transition temperature of As₄₅Te_55−xI_x glasses, even though there is a wide variation in the average coordination number . This observation has been understood on the basis that the variation in glass transition temperature of network glasses is dictated by the variation in average bond energy rather than . Further, it is found that both the non-reversing enthalpy (ΔH_nr) and the thermal diffusivity (α) exhibit a sharp minimum at a composition x = 6. A broad hump is also seen in glass transition and crystallization temperatures in the composition range 5 ? x ? 7. The results obtained clearly indicate a sharp thermally reversing window in As₄₅Te_55−xI_x chalcohalide glasses around the composition x = 6.     

Crystallization behavior and microstructure of powdered and bulk ZnO-Al2O3-SiO2 glass-ceramics

The crystallization behavior of glass with the composition: 55.6 mol% SiO₂, 22.8 mol% Al₂O₃, 17.7 mol% ZnO and 3.84 mol% of TiO₂ as nucleating agent and with different particle sizes has been studied by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and tranmission electron microscopy (TEM). In glass powders two crystalline phases: zinc-aluminosilicate s.s. with high-quartz structure, Zn_x/2Al_xSi_3−xO₆, (x varies dependent on heat-treatment temperature) and gahnite are formed. The ratio of these phases depends on particle sizes. In bulk glass, however, gahnite is the sole crystalline phase. The composition of initially formed zinc-aluminosilicate s.s. was determined by Rietveld refinement of XRD patterns to be Zn_0.69Al_1.38Si_1.62O₆. With temperature increase, the amount of zinc-aluminosilicate s.s decreased with simultaneous reduce of zinc and aluminum incorporated in the structure. Eventually at 1423 K almost pure high-quartz structure was formed. The activation energies of zinc-aluminosilicate s.s. and gahnite crystallization were determined by non-isothermal method to be 510 ± 18 and 344 ± 17 kJ mol⁻¹, respectively. The latter value matches well with those cited in literature for crystal growth of gahnite in similar glasses. That is attributed to the fact that the high-quartz structure acts as a precursor for gahnite crystallization.     

Spectroscopic and magnetic behavior of xNd2O3(1−x)(3Bi2O3 · PbO) glasses

Glasses of the xNd₂O₃(1−x)(3Bi₂O₃ · PbO) system with 0?x?0.30 were obtained and studied by IR spectroscopy, X-ray photoelectron spectroscopy (XPS), density and magnetic susceptibility measurements. IR and density measurements show that the addition of neodymium ions produces structural changes and the neodymium ions play a network modifier role in the host glass matrix. XPS investigation permitted following the evolution of the structural disorder, of the degree of polymerization of bismuthate chains and of the fraction of bridging oxygens with respect to the neodymium ion concentration of the studied glasses. Magnetic susceptibility data show that the Nd³⁺ ions are present as isolated species for x?0.05 and as both isolated and exchange coupled species for higher x values.     

Phase separation and crystallization in the system SiO2-Al2O3-P2O5-B2O3-Na2O glasses

The phase separation and crystallization behavior in the system (80 − X)SiO₂ · X(Al₂O₃ + P₂O₅) · 5B₂O₃ · 15Na₂O (mol%) glasses was investigated. Glasses with X = 20 and 30 phase separated into two phases, one of which is rich in Al₂O₃-P₂O₅-SiO₂ and forms a continuous phase. Glasses containing a larger amount of Al₂O₃-P₂O₅ (X = 40 and 50) readily crystallize and precipitates tridymite type AlPO₄ crystals. It is estimated that the phase separation occurs forming continuous Al₂O₃-P₂O₅-SiO₂ phase at first, and then tridymite type AlPO₄ crystals precipitate and grow in this phase. Highly transparent glass-ceramics comparable to glass can be successfully obtained by controlling heat treatment precisely. The crystal size and percent crystallinity of these transparent glass-ceramics are 20-30 nm and about 50%, respectively.     

Effect of P2O5 content in two series of soda lime phosphosilicate glasses on structure and properties - Part II: Physical properties

The effect of the variation in phosphate (P₂O₅) content on the properties of two series of bioactive glasses in the quaternary system SiO₂-Na₂O-CaO-P₂O₅ was studied. The first series (I) was a simple substitution of P₂O₅ for SiO₂ keeping the Na₂O:CaO ratio fixed (1:0.87). The second series (II) was designed to ensure charge neutrality in the orthophosphate (), therefore as P₂O₅ was added the Na₂O and CaO content was varied to provide sufficient Na⁺ and Ca²⁺ cations to charge balance the orthophosphate present. Network connectivity’s of the glasses were calculated, and densities and thermal expansion coefficients predicted using the Appen and Doweidar models, respectively. Theoretical densities were measured using the Archimedes principle. Characteristic temperatures, namely the glass transition temperature, T_g, and crystallization temperatures, T_x, were obtained using differential analysis (DTA). Two crystallization exotherms were observed for both glass series (T_xi and T_xii). Both T_g and T_x decreased with P₂O₅ addition for both series. The working range of the glasses, T_x-T_g was shown to increase to a maximum at around 4 mol% P₂O₅ then decrease at higher P₂O₅ contents for both series. Thermal expansion coefficients were measured using dilatometry increasing with P₂O₅ addition and showed good agreement with the Appen values. Dilatometric softening points, T_s, were also measured, which increased with P₂O₅ addition. X-ray diffraction (XRD) was performed on the glasses to confirm their amorphous nature. The glass containing 9.25 mol% P₂O₅ from series I exhibited well-defined peaks on the XRD trace, indicating the presence of a crystalline phase.     

Studies of some mechanical and optical properties of: (70 − x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Specimens of the glassy system: (70 − x)TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by the melt-quenching. An ultrasonic pulse-echo technique was employed, at 5 MHz, for measuring: the ultrasonic attenuation, longitudinal and shear wave velocities, elastic moduli, Poisson ratio, Debye temperature and hardness of the present glasses. It is found that the gradual replacement of TeO₂ by Li₂O in the glass matrix up to 30 mol% leads to decrease the average crosslink density and rigidity of prepared samples which affects the properties, i.e., the hardness, ultrasonic wave velocities and elastic moduli are decreased, while the Poisson ratio and the ultrasonic attenuation are increased. Also, optical absorption spectra were recorded in the range, 200-800 nm for these glasses. The obtained results showed that a gradual shift in the fundamental absorption edge toward longer wavelengths occurred. Values of both of the optical energy gap, E_opt, and width tails, ΔE, are determined. It is observed that E_opt is decreased and ΔE increased with the increase of Li₂O in the glass matrix up to 30 mol%. The compositional dependences of the above properties are discussed and correlated to the structure of tested glasses.