Modeling the atomic structure of an amorphous Ni71Nb29 alloy produced by mechanical alloying using reverse Monte Carlo simulations

The local atomic structure of an amorphous Ni₇₁Nb₂₉ alloy produced by mechanical alloying technique was determined using only one X-ray total structure factor S(K) as input data for reverse Monte Carlo (RMC) simulations. The results showed that the amorphous alloy has a local atomic structure similar to that predicted by the additive hard sphere (AHS) model for a Ni and Nb mixture with same composition of the alloy, and quite different of that found in the rhombohedral NiNb crystal. The obtained coordination numbers for the first neighbors showed that the amorphous alloy has a preference to form homopolar pairs.     

Potentiodynamic polarization studies on amorphous Zr46.75Ti8.25Cu7.5Ni10Be27.5, Zr65Cu17.5Ni10Al7.5, Zr67Ni33 and Ti60Ni40 in aqueous HNO3 solutions

Potentiodynamic polarization studies were carried out on virgin specimens of Zr-based bulk amorphous alloys Zr_46.75Ti_8.25Cu_7.5Ni₁₀Be_27.5 and Zr₆₅Cu_17.5Ni₁₀Al_7.5, and conventional-type binary amorphous alloys Zr₆₇Ni₃₃ and Ti₆₀Ni₄₀ in solutions of 0.2 M, 0.5 M and 1.0 M HNO₃ at room temperature. The values of the corrosion current density (I_corr) for the bulk amorphous alloy Zr_46.75Ti_8.25Cu_7.5Ni₁₀Be_27.5 were found to be comparable with those of Zr₆₅Cu_17.5Ni₁₀Al_7.5 in 0.2 M and 0.5 M HNO₃, but the value of I_corr for the former was almost three times more than that of the latter in 1.0 M HNO₃. In the case of conventional binary amorphous alloys, Ti₆₀Ni₄₀ showed lower value of I_corr as compared to Zr₆₇Ni₃₃ in 0.5 M and 1.0 M HNO₃ and a comparable value of I_corr in 0.2 M HNO₃. In general, the binary Ti₆₀Ni₄₀ displayed the best corrosion resistance among all the alloys in all the cases and the corrosion current density (I_corr) for all the alloys was found to increase with the increasing concentration of nitric acid. It is noticed that the bulk amorphous alloys do not possess superior corrosion resistance as compared to conventional binary amorphous alloys in aqueous HNO₃ solutions. The observed differences in their corrosion behavior are attributed to different alloy constituents and composition of the alloys investigated.     

Properties characterization of the Cu68.5Ni12P19.5 alloy at elevated temperatures

The Cu_68.5Ni₁₂P_19.5 alloy was cast into the ribbons using melt spinning (23 m/s). The amorphous ribbon in the as-cast state was investigated by differential thermal analysis (DTA), dynamic mechanical analysis (DMA), resistivity measurements and X-ray diffraction ‘in situ’ at different temperatures. The work presents attempts to find correlation between the changes of the mechanical properties presented by DMA cycles and during the other tests. The measurements of the relative resistivity R/R₀ versus temperature for repeated heating and cooling cycles to different temperatures show changes of the temperature coefficient of resistivity (TCR) indicating reversible and irreversible transformations in the studied alloy.     

Structure of Ni/SiO2 films prepared by sol-gel dip coating

The sol-gel dip coating technique has been used to deposit composite oxide films (NiO)_x(SiO₂)_1−x with x = 0.1 on silicon wafers. Single and multilayer coatings allowed a variation of the film thickness from 70 to 400 nm. Film morphology, atomic structure and atomic composition have been investigated by transmission electron microscopy (TEM) and Rutherford backscattering spectrometry (RBS). The local environment of the Ni atoms was characterized by extended X-ray absorption fine structure (EXAFS). The samples were studied in the as-prepared state and after annealing in H₂ at 600 °C for 1 h. The structural and chemical state evolution of clusters present inside the silica matrix is discussed in terms of out-of-equilibrium reaction processes specific to low-dimensional objects and superficial effects.     

Influence of Gd and Fe on crystallization of Al87Y5Ni8 amorphous alloy

Crystallization of amorphous Al-based alloys (Al-Y-Gd-Ni-Fe) was investigated by applying differential scanning calorimetry (DSC), X-ray diffraction (XRD) and high resolution electron microscopy (HREM). It was shown that the crystallization in the examined alloys proceeds in three stages (DSC maxima). The two first stages are attributed to formation of solid solution of fcc Al(RE) nanograins in amorphous matrix. In the third stage the precipitation of ternary compound Al₁₉Ni₅RE₃ of the orthorhombic Al₁₉Ni₅Gd₃-type structure was observed. A partial substitution of Ni by Fe causes a change of stoichiometry and crystal structure of the ternary compounds: Al₈TM₄RE (TM = Fe, Ni; RE = Y, Gd) of the tetragonal ThMn₁₂ (Al₈Mn₄Ce)-type structure. A partial replacing of Y atoms by Gd in the Al₈₇Y₅Ni₈ based alloy shifts the Al(RE) nanocrystallization to lower temperatures. In contrast to this a partial replacing of Ni by Fe shifts the nanocrystallization to higher temperatures.     

Structural transformation on Se0.8Te0.2 chalcogenide glass

Using X-ray diffraction and differential scanning calorimetry (DSC), the structure and the crystallization mechanism of Se_0.8Te_0.2 chalcogenide glass has been studied. The structure of the crystalline phase has been refined using the Rietveld technique. The crystal structure is hexagonal with lattice parameter a = 0.443 nm and c = 0.511 nm. The average crystallite size obtained using Scherrer equation is equal 16.2 nm, so it lies in the nano-range. From the radial distribution function, the short range order (SRO) of the amorphous phase has been discussed. The structure unit of the SRO is regular tetrahedron with (r₂/r₁) = 1.61. The Se_0.8Te_0.2 glassy sample obeys the chemical order network model, CONM. Some amorphous structural parameters have been deduced. The crystallization mechanism of the amorphous phase is one-dimensional growth. The calculated value of the glass transition activation energy (E_g) and the crystallization activation energy (E_c) are 159.8 ± 0.3 and 104.3 ± 0.51 kJ/mol, respectively.     

Structure and properties of Ni60(Nb100−xTax)34Sn6 bulk metallic glass alloys

Refractory bulk metallic glasses and bulk metallic glass composites are formed in quaternary Ni-Nb-Ta-Sn alloy system. Alloys of composition Ni₆₀(Nb_100−xTa_x)₃₄Sn₆ (x = 20, 40, 60, 80) alloys were prepared by injection-casting the molten alloys into copper molds. Glassy alloys are formed in the thickness of half mm strips. With thicker strips (e.g., 1 mm), Nb₂O₅ and Ni₃Sn phases and the amorphous phase form an in situ composite. Glass transition temperatures, crystallization temperatures, and ΔT_x, defined as T_x1 − T_g (T_x1: first crystallization temperature, T_g: glass transition temperature) of the alloys increase dramatically with increasing Ta contents. These refractory bulk amorphous alloys exhibit high Young’s modulus (155-170 GPa), shear modulus (56-63 GPa), and estimated yield strength (3-3.6 GPa).     

Compositional dependence of the optical properties of amorphous Sb2Se3−xSx thin films

Thin films of Sb₂Se_3−xS_x solid solutions (x = 0, 1, 2, and 3) were deposited by thermal evaporation of presynthesized materials on glass substrates held at room temperature. The films compositions were confirmed by using energy dispersive analysis of X-rays (EDAX). X-ray diffraction studies revealed that all the as-deposited films as well as those annealed at T_a < 423 K have amorphous phase. The optical constants (n, k) and the thickness (t) of the films were determined from optical transmittance data, in the spectral range 500-2500 nm, using the Swanepoel method. The dispersion parameters were determined from the analysis of the refractive index. An analysis of the optical absorption spectra revealed an Urbach’s tail in the low absorption region, while in the high absorption region an indirect band gap characterizes the films with different compositions. It was found that the optical band gap energy increases quadratically as the S content increases.     

Crystallization processes in amorphous Zr54Cu46 alloy

The crystallization of amorphous Zr₅₄Cu₄₆ alloy was investigated by using X-ray diffraction (XRD), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM) techniques. The experimental results show that an endothermic peak in DSC traces for amorphous Zr₅₄Cu₄₆ alloy exists at about 1006 K, indicating following eutectoid reaction occurs, namely, Cu₁₀Zr₇+CuZr₂↔CuZr in amorphous Zr₅₄Cu₄₆ alloy during heating. With increasing the heating rate, the glass transition temperature T_g and onset crystallization temperature T_x of amorphous Zr₅₄Cu₄₆ alloy increase in parallel, and the supercooled liquid region ΔT_x (=T_x−T_g) holds almost constant with an average value of 44 K. Both XRD and TEM results prove that Cu₁₀Zr₇ and CuZr₂ are main crystallization products for amorphous Zr₅₄Cu₄₆ alloy under continuous heating conditions. No CuZr phase is identified because of its small precipitation amount. Finally, the crystallization processes of amorphous Zr₅₄Cu₄₆ alloy were summarized.     

Magnetic susceptibility and atomic structure of paramagnetic Zr–(Co, Ni, Cu) amorphous alloys

The experimental results for the magnetic susceptibility and superconducting transition temperature of amorphous Zr–(Co, Ni, Cu) alloys extending over a wide composition range are analyzed in some detail. By combining the results of this analysis with the literature results for the electronic density of states at E_F for the same alloy systems we obtained a set of parameters associated with the electronic structure of the amorphous Zr. The comparison of these parameters with the results of the band structure calculations for different crystalline phases of Zr and with the results of the atomic structure and crystallization studies of the same alloy systems indicates an fcc-like local atomic structure for amorphous Zr.     

Fabrication and properties of novel low-melting glasses in the ternary system ZnO-Sb2O3-P2O5

Glasses in the ternary system ZnO-Sb₂O₃-P₂O₅ were investigated as potential alternatives to lead based glasses for low temperature applications. The glass-forming region of ZnO-Sb₂O₃-P₂O₅ system has been determined. Structure and properties of the glasses with the composition (60 − x)ZnO-xSb₂O₃-40P₂O₅ were characterized by infrared spectra (IR), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results of IR indicated the role of Sb³⁺ as participant in glass network structure, which was supported by the monotonic and remarkable increase of density (ρ) and molar volume (V_M) with increasing Sb₂O₃ content. Glass transition temperature (T_g) and thermal stability decreased, and coefficient of thermal expansion (α) increased with the substitution of Sb₂O₃ for ZnO in the range of 0-50 mol%. XRD pattern of the heat treated glass containing 30 mol% Sb₂O₃ indicated that the structure of antimony-phosphate becomes dominant. The improved water durability of these glasses is consistent with the replacement of easily hydrated phosphate chains by corrosion resistant P-O-Sb bonds. The glasses containing ?30 mol% Sb₂O₃ possess lower T_g (<400 °C) and better water durability, which could be alternatives to lead based glasses for practical applications with further composition improvement.     

Partial correlations in Ni60Nb40 metallic glass

Combined X-ray and neutron diffraction experiments were performed on the Ni₆₀Nb₄₀ metallic glass samples prepared by rapid quenching from the melt with natural Ni^nat and isotope ⁵⁸Ni, respectively. The partial structure factors were separated for the three kinds of atomic pairs: NiNi, NiNb and NbNb. The partial distribution functions were calculated by means of Fourier transformation and the following atomic distances were obtained: $\text{r}{}_{\mathrm{<mtext>NiNi</mtext>}}\text{=2.52}\text{A}\text{?}\text{, r}{}_{\mathrm{<mtext>NiNb</mtext>}}\text{=2.72}\text{A}\text{?}$ and $\text{r}{}_{\mathrm{<mtext>NbNb</mtext>}}\text{=2.70}\text{A}\text{?}$. The values n_NiNi=7.3, n_NiNb=4.5, n_NbNi=6.8 and n_NbNb=5.4 were obtained for the number of nearest neighbours.     

Ball milling induced abnormal crystallization behavior of an amorphous Fe78Si9B13 alloy

This paper investigates the effect of milling atmospheres on mechanical crystallization of an amorphous Fe₇₈Si₉B₁₃ alloy during ball milling. Under an air atmosphere, the amorphous alloy completely transforms into a single α-Fe(Si) phase after milling of 30 h. The crystallization process and products are different from those of thermal crystallization and milling induced crystallization under an argon atmosphere. Moreover, the milling atmosphere has a significant influence on the thermal crystallization of the amorphous phase in the as-milled alloy.     

Crystallization of amorphous Ni35Zr65 and Fe40Ni40P14B6 under proton irradiation

Two amorphous alloys, Ni₃₅Zr₆₅ and Fe₄₀Ni₄₀P₁₄B₆, were irradiated using 400 keV protons at several temperatures below the crystallization temperature, T_x, to peak doses in the neighborhood of 3.5 to 4.5 dpa. Irradiation at 250°C resulted in the crystallization of both alloys, which were examined by transmission electron microscopy of samples electrolytically polished to various distances from the irradiated surface to study the effect of dose. Samples masked from the proton beam remained amorphous during irradiation. In the Ni₃₅Zr₆₅ alloy crystallization of the equilibrium phases propagated throughout the entire sample, while the in the Fe₄₀Ni₄₀P₁₄B₆ alloy crystallization was observed only in those parts of the samples lying within the proton range. Neither alloy crystallized during irradiation at 100°C. In both these alloys the amorphous phase is therefore evidently stable at irradiation temperatures below approximately 0.6 T_x. An examination of the literature on irradiation damage of binary alloys and intermetallic compounds suggests that there is a tendency for initially amorphous alloys to remain amorphous at irradiation temperatures, T_irr < 0.3 T_L, where T_L (≈T_x) is the “melting” temperature (either a eutectic, peritectic or congruent melting temperature). Also, these same alloys, even when they are initially crystalline, transform to the amorphous state during irradiation at T < 0.3 T_L. Some other crystalline alloys have also been shown to transform to the amorphous state at T_irr < 0.3 T_L even though they have never been prepared in this condition by rapid quenching techniques. The temperature 0.3 T_L appears to be a lower limit, however, since the crystalline to amorphous transformation occurs in many of these alloys at temperatures greater than 0.3 T_L. It is suggested, by analogy with results on void formation in irradiated metals, that this low temperature limit is related to the low mobility of vacancies in these materials, although the mechanism of crystallization, or conversely amorphization, is not fully understood.     

Crystallization kinetics of (Ni0.75Fe0.25)78Si10B12 amorphous alloy

Amorphous ribbon specimen of (Ni_0.75Fe_0.25)₇₈Si₁₀B₁₂ has been prepared by a single roller melt-spinning technique in the air atmosphere. The crystallization kinetics of the alloy has been investigated using different thermal analysis by means of continuous heating and isothermal heating. The activation energy of the alloy has been calculated by using Kissinger plot method and Ozawa plot method based on differential thermal analysis data, respectively. The products of crystallization have been analyzed by X-ray diffraction. A single phase of γ-(Fe, Ni) solid solution with grain size of about 10.3 and 18.5 nm precipitates in the amorphous matrix after annealing at temperatures 715 and 745 K, respectively. The crystallized phases are γ-(Fe, Ni) solid solution, Fe₂Si, Ni₂Si, Fe₃B and unidentified phase after annealing at 765 K. The details of nucleation and growth during the isothermal crystallization are expatiated in terms of local Avrami exponent and local activation energy.     

Disorder in LixFePO4: From glasses to nanocrystallites

Li_xFePO₄ glasses have been prepared by fast-quenching method in the whole range of composition 0 ? x ? 1. The amorphous state of glassy materials is confirmed by X-ray diffraction. Information concerning the local environment of Li and Fe cations and the configuration of (PO₄)³⁻ oxo-anions is obtained by Fourier transform infrared (FTIR) spectroscopy. While the LiFePO₄ crystalline materials undergo a transition from the paramagnetic to the antiferromagnetic ordering at 52 K, no magnetic ordering is observed in the vitreous samples that realize random field systems, so that a spin glass-like freezing is observed at low temperature. The paramagnetic Curie temperature of Li_xFePO₄ is independent of x and shifted to θ = −60 K in the glassy state, due to a significant distortion of the FeO₆ octahedra that alters the superexchange path inside the atomic FeO₄ layers of the crystallized structure. On another hand, the PO₄ tetrahedra are not significantly distorted in the glassy phase. The results are compared with highly disordered, but nanocrystallized LiFePO₄ recently obtained at the early stage of synthesis by solid state reaction at 300 °C. In this latter case, the lack of long-range antiferromagnetic ordering is due to substitutional disorder among the cationic sublattice.     

Distorted icosahedral Ni5Nb3Zr5 clusters in the as-quenched and hydrogenated amorphous (Ni0.6Nb0.4)0.65Zr0.35 alloys

Local structures of the hydrogenated (Ni_0.6Nb_0.4)_1-xZr_x (x = 0.3-0.4) amorphous alloys attract much attention for the sake of their epoch-making electronic transport behaviors. We investigated the local structures by XAFS for the as-quenched (Ni_0.6Nb_0.4)_0.65Zr_0.35 and hydrogenated [(Ni_0.6Nb_0.4)_0.65Zr_0.35]_0.922H_0.078 amorphous alloys, in which ballistic conductivity has been observed. XAFS results of the Ni K-edge are analyzed based on the structure model deduced by the first principle calculation. The analysis suggests that highly distorted icosahedral Ni₅Nb₃Zr₅ cluster, which has a centered-Ni and a surrounding Nb triangle, is a main structural unit of (Ni_0.6Nb_0.4)_0.65Zr_0.35 and the [(Ni_0.6Nb_0.4)_0.65Zr_0.35]_0.922H_0.078 amorphous alloys. This distorted icosahedral Ni₅Nb₃Zr₅ cluster can be associated with the occurrence of the singular electronic transport behaviors of the hydrogenated (Ni_0.6Nb_0.4)_0.65Zr_0.35 alloy.     

Structural investigation of an amorphous Si24Nb76 alloy produced by mechanical alloying using reverse Monte Carlo simulations

The atomic structure of an amorphous Si₂₄Nb₇₆ alloy produced by mechanical alloying was investigated by using one X-ray total structure factor S(K) as input data for reverse Monte Carlo (RMC) simulations. The partial S_Si–Si(K), S_Si–Nb(K), S_Nb–Nb(K) structure factors and G_Si–Si(r), G_Si–Nb(r), G_Nb–Nb(r) pair probability functions were obtained from the RMC simulations. The structural parameters (interatomic distances and co-ordination numbers) for the first neighbors were extracted and compared with those found in the Nb₃Si compound. It was observed some resemblance between these phases.     

Crystallization of amorphous Cu60Zr40 prepared by magnetron sputter deposition

The crystallization of amorphous Cu₆₀Zr₄₀ prepared by magnetron sputter deposition was studied by differential scanning calorimetry, X-ray diffraction and transmission electron microscopy. Calorimetric results were similar to those reported in the literature for liquid-quenched Cu₆₀Zr₄₀, including the manifestation of a glass transition. Crystallization above and below the glass transition temperature, T_g, occurred by nucleation and growth of the equilibrium phase, Cu₁₀Zr₇. This phase was characterized by convergent beam electron diffraction. With isothermal annealing below T_g, the time scale for crystallization indicated that the vapor-quenched alloy was kinetically more stable than the liquid-quenched alloy. This was interpreted as a difference in the quenched-in structures, produced by the different synthesis methods. During longer anneals, TEM analysis indicated that the structure was being contaminated by oxygen.