端羟基聚丁二烯/增塑剂共混物相容性的分子动力学模拟

固体推进剂和炸药的力学性能在很大程度上依赖于配方中高分子粘结剂与增塑剂的相容性. 本文对相容和非相容两种体系进行了分子动力学(MD)模拟, 以考察分子模拟方法的实用性. 为预测固体推进剂中端羟基聚丁二烯(HTPB)与增塑剂癸二酸二辛酯(DOS)、硝化甘油(NG)的相容性, 采用MD模拟方法在COMPASS力场下, 对HTPB、DOS、NG和共混物HTPB/DOS、HTPB/NG的密度、内聚能密度及溶度参数等进行了模拟计算. 通过比较溶度参数差值(△δ)的大小、分子间径向分布函数和模拟前后体系密度变化情况均可以预测HTPB/DOS属于相容体系,而HTPB/NG属于不相容体系, 与实验结果一致. 径向分布函数分析同时揭示了HTPB/增塑剂组分之间的相互作用及本质. 本文的模拟方法可以作为预测聚合物与增塑剂相容性的有利工具, 也可以为固体推进剂和炸药的配方设计提供理论指导.     

端羟基聚丁二烯/增塑剂共混物相容性的分子动力学模拟和介观模拟

应用分子动力学(MD)和介观动力学(MesoDyn)模拟方法对固体推进剂中端羟基聚丁二烯(HTPB)与增塑剂癸二酸二辛酯(DOS)、硝化甘油(NG)的相容性进行了研究. 采用MD模拟方法在COMPASS力场下, 对纯物质、HTPB/增塑剂共混物的密度、内聚能密度、溶度参数和共混物分子间的Flory-Huggins作用参数及结合能等进行了模拟计算, 通过比较溶度参数差值(Δδ)的大小、模拟前后体系密度变化情况均可以预测HTPB与增塑剂的相容性, 结合能的分析揭示了HTPB/增塑剂共混物组分间的相互作用及本质. 将Flory-Huggins作用参数转化为MesoDyn模拟的输入参数, 采用MesoDyn模拟方法对HTPB/增塑剂共混体系的介观形貌与动力学演变过程进行了研究, 通过模拟得到的等密度图、自由能密度和有序度参数等可以判断共混体系的相容性. MD和MesoDyn模拟结果均表明: HTPB/DOS属于相容体系, 而HTPB/NG属于不相容体系, 其结论与实验结果一致.     

HTPB固体推进剂增塑剂选取分子模拟研究

固体推进剂中增塑剂要求同粘合剂体系相容性良好,并提高体系的低温性能.本文采用分子动力学(MD)方法,首先计算了端羟基聚丁二烯(HTPB)粘合剂及增塑剂癸二酸二辛酯(DOS)、己二酸二辛酯(DOA)、壬酸异癸酯(TOA)、邻苯二甲酸二丁酯(DBP)和邻苯二甲酸二辛酯(DOP)的溶度参数,以此从相容性角度选取推进剂增塑剂;计算数值基本吻合实验值,表明常用的增塑剂从相容性都能满足要求.其次模拟获取了HTPB及HTPB/增塑剂混合体系的比体积-温度关系得到了体系的玻璃化转变温度(Tg),揭示增塑剂对HTPB体系低温性能的影响.结果显示:(1)HTPB的Tg模拟值为202K,基本吻合实验值196K.(2)HTPB/DOS混合体系中,当增塑剂DOS的质量含量从12%、22%、29%到36%(摩尔含量分别为50%、66%、75%和90%)增加时,体系的Tg线性降低;TOA和DOP增塑的粘合剂体系(摩尔含量为75%)Tg也降低,而增塑剂DOA和DBP对体系的Tg影响不大.因此,基于相容性及提高粘合剂低温性能考虑,DOS、DOA和DOP作为HTPB的增塑剂优于TOA和DBP.     

粘度法研究氯化聚丙烯和涂料树脂间的相容性

用稀溶液粘度法研究了氯化聚丙烯与石油树脂、丙烯酸树脂和醇酸树脂间的相容性,并用α判据对相容性结果进行判别。结果显示,石油树脂/氯化聚丙烯的共混体系是相容的;丙烯酸树脂/氯化聚丙烯的共混体系是不相容的。而醇酸树脂与氯化聚丙烯的相容性情况复杂,由二者的组成决定。当m(醇酸树脂)∶m(氯化聚丙烯)1∶1时,体系是相容的;当m(醇酸树脂)∶m(氯化聚丙烯)1∶1时,体系是不相容的。通过共溶剂法和涂膜宏观特性对上述体系的相容性进行测定,所得结果与α判据的结果相符合,印证了稀溶液粘度法研究溶液中高分子间的相互作用来预测涂料树脂的相容性具有一定可行性。     

改性酚氧树脂/聚(甲基丙烯酸丁酯-co-4-乙烯基吡啶)共混物的相容-络合行为和表面表征

合成了一系列不同4-乙烯基吡啶含量的聚(甲基丙烯酸丁酯-co-4-乙烯基吡啶)(BVPy)共聚物,并对酚氧树脂(Phenoxy)的仲羟基进行了不同乙酰化程度的改性.用粘度法和激光光散射(LLS)研究了BVPy/改性Phenoxy共混物在溶液中的络合行为对氢键相互作用基团密度的依赖性,并用DSC研究了共混体系在本体中的相容性.将粘度法及LLS的结果结合起来,得到了改性Phenoxy/BVPy共混体系的不相容-相容-络合转变相图.在此基础上,用XPS初步考察了共混物的相容性对其表面组成的影响.结果表明,大分子间的络合相互作用可抑制共混物的表面富集.     

SAN共聚物组成对PVC/ABS共混物相容性的影响

采用乳液聚合技术通过改变共聚单体的投料比(St/AN)合成了一系列不同AN结合量的ABS接枝共聚物粉料和SAN共聚物.将其与聚氯乙烯(PVC)和邻苯二甲酸二辛酯(DOP)熔融共混分别制得了PVC/ABS、PVC/SAN、PVC/ABS/DOP和PVC/SAN/DOP共混物,利用SEM、TEM和动态力学粘弹谱仪(DMA)对共混物的相容性和相结构进行了表征.结果发现,在PVC/ABS共混体系中,尽管改变接枝SAN共聚物的AN结合量,PVC和SAN共聚物均为不相容体系;在该共混物中引入增塑剂DOP后,虽然当SAN共聚物AN结合量小于23.4 wt%时,共混物在室温以上只存在一个tanδ峰,但形态结构研究结果表明共混物仍为不相容体系,共混物的相区尺寸明显地依赖于SAN共聚物中的AN结合量,当AN结合量为23.4 wt%时相区尺寸最小.     

硝酸酯增塑剂力学性能和界面相互作用的分子动力学模拟

运用分子动力学(MD)方法, 模拟研究了硝化甘油(NG)及其与硝化三乙二醇(TEGDN)组成的硝酸酯增塑剂的低温力学性能. 结果表明, NG/TEGDN混合体系较NG单组分体系的刚性减弱, 延展性和各向同性增强. 结合能计算和径向分布函数分析揭示了混合型硝酸酯增塑剂组分之间的相互作用及其本质.     

显微镜图像分析研究聚丙烯/尼龙1010共混物相结构及其性能

用扫描电子显微镜图像分析研究了聚丙烯/聚酰胺1010共混物及其部分相容体系的相形态结构,计算了表征相结构和尺寸的结构参数,如分散相的平均直径、平均弦长和分散相的质心相关距等.并分别讨论了聚丙烯/聚酰胺1010共混物及其部分相容体系的相形态以及其结构参数与共混物组成的关系.测定了聚合物及其共混物体系的力学性能,讨论了共混物组成与力学性能的关系.聚丙烯/聚酰胺1010共混物的拉伸模量与组成的关系较为复杂,但其部分相容体系的拉伸模量与组成呈线性关系.聚丙烯/聚酰胺1010及其共混物体系的屈服强度与共混物组成均呈线性关系.表征相结构的两相平均弦长比(l-1/-l2)与组成以及共混物体系力学性能与组成的关系,二者相似.同时讨论了体系力学性能随相尺寸等的变化规律.     

分子动力学模拟研究聚乳酸/聚酰胺11共混物的相容性

采用分子动力学(MD)模拟方法在COMPASS力场下,研究了不同质量比(10/90,30/70,50/50,70/30和90/10)聚乳酸(PLA)/聚酰胺11(PA11)共混物的相容性.研究结果表明:不同比例下PLA/PA11共混物的Gibbs自由能变化均大于零,其共混物很难形成均相体系;共混体系结合能的计算以及不同组分分子间C—C原子对径向分布函数的分析揭示了PLA和PA11的相互作用主要源自其分子间的范德华力;此外,模拟得到的所有比例下共混物的Flory-Huggins相互作用参数(χ)均大于临界Flory-Huggins相互作用参数(χcritical),进一步证明PLA与PA11不能形成相容体系。     

苯酰化聚苯醚/聚苯乙烯共混物相容性研究

采用DSC方法研究了聚苯乙烯(PS)和苯甲酰化聚苯醚(APPO)共混体系的相容性.相容共混体系Gordon-Taylor方程K参数随苯甲酰化程度(取代度)增加而变小,其玻璃化转变区随取代度增加而变宽,取代度大于76mol％时,共混物呈现双玻璃化转变.APPO/PS共混体系热诱导相图同时存在LCST和UCST现象,且相行为是可逆的.     

Mechanical and thermal properties of poly(3-hydroxybutyrate) blends with starch and starch derivatives

Poly(3-hydroxybutyrate) (PHB) is a highly crystalline, biodegradable and biocompatible thermoplastic. However, its limited utilization as a commodity plastic is associated to both high cost and very poor mechanical properties. Blending PHB with a natural polymer, such as starch, is one way to improve its properties and to get low price raw materials, though they are not miscible since there are no strong interactions between the hydrophilic starch and the hydrophobic PHB. In this study binary blends of PHB were prepared with natural starch, starch-adipate and grafted starch-urethane derivatives. The PHB blends were characterized in terms of their mechanical and thermal properties. For all blends a decrease of the Young modulus was observed as compared to the pure PHB. However, blends containing natural starches and starch adipate resulted in brittle materials. A significant decrease of both glass transition temperature (Tg) and melting point (Tm) was observed for all formulations. The best results, lower modulus and Tg were obtained with grafted starch-urethane blends using poly(propylene glycol).     

Miscible blends through hydrogen bonding: effects on polymer properties

Miscible blends through hydrogen bonding have been intensively studied. The effects of a variety of miscible hydrogen bonded polymer blends on properties such as thermal and thermal oxidative stability, moisture sensitivity, modulus and glass transition temperature are discussed. In addition, the preparation of semi-interpenetrating polymer networks (IPNs) and studies of the effect of crosslinking on the miscibility in hydrogen bonded polymer blends are reviewed.     

PPEKK/PEI共混物的相容性及拉伸性能

作为相容体系 ,聚芳醚酮与聚醚酰亚胺 (ＰＥＩ)共混物体系的研究受到了研究者的重视[1～ 4] .由于现在已商品化的聚芳醚酮基本上都是半结晶型聚合物 ,所以有有关无定型聚芳醚酮与聚醚酰亚胺共混物的研究鲜见报道 .含二氮杂萘酮结构聚芳醚酮酮 (ＰＰＥＫＫ)是一种新型耐高温聚合物 ,相比于已经商品化的各种聚芳醚酮 ,ＰＰＥＫＫ除具有优异的综合性能外 ,它最大的特点表现在以下两方面 ,ＰＰＥＫＫ耐热性突出 ,玻璃化转变温度 (Ｔｇ)为 2 4 5℃左右 ,远高于各种商品化的聚芳醚酮 ;ＰＰＥＫＫ为无定型聚合物 ,易溶于多种有机极性溶剂 ,大大的扩…     

Miscibility of semirigid thermotropic liquid crystalline polycarbonate with poly(vinyl chloride)

Miscibility and morphology of polymer blends of semirigid thermotropic liquid crystalline (LC) polycarbonate (LCPC) with three commercial amorphous poly(vinyl chloride)s (PVC) having various molecular weights were investigated by means of differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). No phase separation was observed in the LCPC/PVC polymer blends. LCPC forms miscible polymer blends with the PVCs independent of molecular weight. The dynamic storage modulus of the LCPC/PVC polymer blends changes systematically with blend composition.     

Effective interaction parameter of linear/star polymer blends and comparison with that of linear/linear and star/star blends

The authors present a detailed study of the microscopic parameters, which control the miscibility in binary linear/star polymer blends. The effective interactions of linear/star polymer blends are studied by means of Monte Carlo simulations and comparison is made with linear/linear and star/star blends, which they also determined. Using the bond fluctuation model on a simple cubic lattice, the authors are able to simulate symmetric linear/linear, star/star, and, for the first time, linear/star blends with a moderate number of arms. The simulations were performed at a volume fraction of occupied lattice sites phi=0.5, which corresponds to dense polymer mixtures for this algorithm. In particular, we study star/star blends with 4, 8, and 12 arms and the respective linear/linear blends as well as linear/star blends, all having the same total number of units equal to 73 and 121. The authors find that linear/star blends are more miscible than the corresponding linear/linear blends, which is in agreement with recent experimental and theoretical results. They find that linear/star mixtures are less miscible than star/star blends, a result which is also verified by theoretical findings.     

Network architecture and modulus of miscible heteropolymer blends

The architecture and entanglement density of a multicomponent polymer network composed of miscible, flexible chains is related to the corresponding properties and concentrations of the pure components. It is assumed that the coupling frequency between different chain species is proportional to their fractional participation in the blend and that the entanglement ability of polymers can be affected by the presence of heteropolymer neighbors. The theory, equally applicable to temporary and permanent networks, estimates the molecular weight between entanglements and their total number along a chain in the blend. This information is used in establishing a mixing law for the rubbery plateau modulus of a fluid polymer blend and in deriving a relationship for the equilibrium modulus of an interpenetrating polymer network containing trapped entanglements and dangling segments. The theoretical predictions are compared with experimental results from the literature on several miscible polymer blends.     

Hydroxyl-terminated Polyethylenes Bearing Functional Side Groups: Facile Synthesis and Their Properties

A series of hydroxyl-terminated polyethylenes(HTPE) bearing various functional side groups(e.g. carboxyl, ester and butane groups)were synthesized by the combination of ring-opening metathesis polymerization(ROMP) and visible light photocatalytic thiol-ene reaction. The products are named as α,ω-dihydroxyl-poly[(propionyloxythio)methinetrimethylene](HTPE~(carboxyl)), α,ω-dihydroxyl-poly[(methylpropionatethio)methinetrimethylene](HTPE~(ester)) and α,ω-dihydroxyl-poly[(butylthio) methinetrimethylene](HTPE~(butane)), respectively. The investigation of ROMP indicated that the molecular weight of resultant hydroxyl-terminated polybutadiene(HTPB) can be tailored by varying the feed ratios of monomer to chain transfer agent(CTA). The exploration of the photocatalytic thiol-ene reaction between HTPB precursor and methyl 3-mercaptopropionate revealed that blue light as well as oxygen accelerated the reaction. 1 H-NMR and ~(13) C-NMR results verified all the double bonds in HTPB can be modified, and the main chain of resultant polymer can be considered as polyethylene. Subsequently, relationship between the structure of side groups and the thermal properties of functional PEs was studied. And the results suggested that the T_g was in the order of HTPE~(butane)HTPE~(ester)HTPE~(carboxyl). Greater interaction between side groups resulted in higher T_g. Moreover, all the functional PE samples exhibited poor thermostability as compared to HTPB. Finally, the promising applications for functional PEs were explored. HTPE~(carboxyl) can be utilized as a smart material with p H-responsive properties due to its p H-dependent ionization of carboxyl side groups. HTPE~(butane) can be employed as a macro-initiator for building the triblock copolymer due to the presence of active hydroxyl end groups. HTPE~(ester) can serve as a plasticizer for PVC which can enhance the ductility of PVC without obviously sacrificing strength.     

Comparison of the glass transition temperature and fragility parameter of isomalto-olygomer predicted by molecular dynamics simulations with those measured by differential scanning calorimetry

The purpose of this study is to examine whether molecular dynamics (MD) simulations using a commercially available software for personal computers can estimate the glass transition temperature (Tg) of amorphous systems containing pharmaceutically-relevant excipients. MD simulations were carried out with an amorphous matrix model constructed from isomaltoheptaose, and the Tg estimated from the calculated density versus temperature profile was compared with the Tg measured by differential scanning calorimetry (DSC) for freeze-dried isomalto-oligomer having an average molecular weight close to that of isomaltoheptaose. The Tg values determined by DSC were lower by 10 to 20 K than those extrapolated from the Tg values estimated by MD simulation. Fragility parameter was estimated to be 56 and 51 from MD simulation and from DSC measurement, respectively. Thus, the results suggest that MD simulation can provide approximate estimates for the Tg and fragility parameter of amorphous formulations. However, a reduction of the cooling rate, achievable by sufficiently elongating the simulation duration, is necessary for more accurate estimation.