Dithieno[2,3‐d:2',3'‐d']benzo[1,2‐b:4,5‐b']dithiophene (DTBDAT)‐based copolymers for high‐performance organic solar cells

P(BDT‐TCNT) and P(DTBDAT‐TCNT) , which has an extended conjugation length, were designed and synthesized for applications in organic solar cell (OSCs). The solution absorption maxima of P(DTBDAT‐TCNT) with the extended conjugation were red‐shifted by 5–15 nm compared with those of P(BDT‐TCNT) . The optical band gaps and highest occupied molecular orbital (HOMO) energy levels of both P(BDT‐TCNT) and P(DTBDAT‐TCNT) were similar. The structure properties of thin films of these materials were characterized using grazing‐incidence wide‐angle X‐ray scattering and tapping‐mode atomic force microscopy, and charge carrier mobilities were characterized using the space‐charge limited current method. OSCs were formed using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as the electron acceptor and 3% diphenylether as additive suppress aggregation. OSCs with P(BDT‐TCNT) as the electron donor exhibited a power conversion efficiency (PCE) of 4.10% with a short‐circuit current density of J_SC = 9.06 mA/cm², an open‐circuit voltage of V_OC = 0.77 V, and a fill factor of FF = 0.58. OSCs formed using P(DTBDAT‐TCNT) as the electron donor layer exhibited a PCE of 5.83% with J_SC = 12.2 mA/cm², V_OC = 0.77 V, and FF = 0.62. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3182–3192     

Anthracene‐Containing Wide‐Band‐Gap Conjugated Polymers for High‐Open‐Circuit‐Voltage Polymer Solar Cells

The synthesis, characterization, and photophysical and photovoltaic properties of two anthracene‐containing wide‐band‐gap donor and acceptor (D–A) alternating conjugated polymers ( P1 and P2 ) are described. These two polymers absorb in the range of 300–600 nm with a band gap of about 2.12 eV. Polymer solar cells with P1 :PC₇₁BM as the active layer demonstrate a power conversion efficiency (PCE) of 2.23% with a high V_oc of 0.96 V, a J_sc of 4.4 mA cm⁻², and a comparable fill factor (FF) of 0.53 under simulated solar illumination of AM 1.5 G (100 mW cm⁻²). In addition, P2 :PC₇₁BM blend‐based solar cells exhibit a PCE of 1.42% with a comparable V_oc of 0.89 V, a J_sc of 3.0 mA cm⁻², and an FF of 0.53.

     

Highly Efficient Dye‐Sensitized Solar Cells Based on Panchromatic Ruthenium Sensitizers with Quinolinylbipyridine Anchors

Panchromatic Ru^II sensitizers TF‐30–TF‐33 bearing a new class of 6‐quinolin‐8‐yl‐2,2′‐bipyridine anchor were synthesized and tested under AM1.5 G simulated solar irradiation. Their increased π conjugation relative to that of the traditional 2,2′:6′,2′′‐terpyridine‐based anchor led to a remarkable improvement in absorptivity across the whole UV–Vis–NIR spectral regime. Furthermore, the introduction of a bulky tert‐butyl substituent on the quinolinyl fragment not only led to an increase in the J_SC value owing to the suppression of dye aggregation, but remarkably also resulted in no loss in V_OC in comparison with the reference sensitizer containing a tricarboxyterpyridine anchor. The champion sensitizer in DSC devices was found to be TF‐32 with a performance of J_SC=19.2 mA cm^?2, V_OC=740 mV, FF=0.72, and η=10.19 %. This 6‐quinolin‐8‐yl‐2,2′‐bipyridine anchor thus serves as a prototype for the next generation of Ru^II sensitizers with any tridentate ancillary.     

Effect of long alkyl chains of aniline donor on the photovoltaic performance of D‐π‐A zinc porphyrin for dye‐sensitized solar cells

Three novel dyes of JJ1 , JJ2 , and JJ6 featured zinc porphyrin as a basic core structure; N, N‐alkyl‐4‐(prop‐1‐yn‐1‐yl)aniline as an electron donor linked to meso‐10‐position; 4‐(prop‐1‐yn‐1‐yl)benzoic acid as an electron acceptor linked to meso‐20‐position; and 2,6‐bis(dodecyloxy)phenyl or 2,6‐bis(octyloxy)phenyl respectively linked to meso‐5 and meso‐15‐positions of zinc porphyrin have been synthesized and used for dye‐sensitized solar cells. Porphyrin JJ6 featured the shortest alkyl group (─C₄H₉) on the donor, whereas JJ2 contained the longest alkyl groups (─C₁₂H₂₅), and JJ1 has a medium length of octyl groups. With these new porphyrin sensitizers, we observed that JJ6 has 7.55% power conversion efficiency under simulated one‐sun illumination (AM 1.5 G, 100 mW/cm²) with J_SC = 18.64 mA/cm², V_OC = 0.66 V, and fill factor (FF) = 0.61, which was higher than the other two; JJ1 (7.35%) with J_SC = 18.83 mA/cm², V_OC = 0.68 V, and FF = 0.60; and JJ2 (6.33%) with J_SC = 15.69 mA/cm², V_OC = 0.62 V, and FF = 0.65. The power conversion efficiency of JJ6 and JJ1 were higher than JJ2 , demonstrating that the lengthy alkyl groups on the aniline cause a decrease in efficiency of the devices.     

D-A-D-based Unsymmetrical Thiosquaraine Dye for the Dye-Sensitized Solar Cells†

In dye-sensitized solar cell, modulating the electronic properties of the sensitizer by varying the donor, π-spacer, acceptor and anchoring groups help optimizing the structure of the dye for better device performance. Here, a donor–acceptor–donor-based unsymmetrical thiosquaraine sensitizer ( SQ5S ) has been designed and synthesized. Photophysical, electrochemical, theoretical and photovoltaic characterizations of SQ5S dye have been compared with its oxygen analog, SQ5 . The incorporation of the sulfur atom in the acceptor unit of SQ5S dye showed an intense peak at 688 nm, which was 38 nm of red-shifted and showed the panchromatic light harvesting response with the onset of 850 nm compared with SQ5 dye. The LUMO and HOMO energy levels are well aligned with the conduction band of TiO₂ and the redox potential of electrolyte for the charge injection and the dye-regeneration processes, respectively. Photovoltaic efficiency of 1.51% (V_OC 610 mV, J_SC 3.07 mA cm⁻², ff 81%) has been achieved for SQ5S dye, whereas SQ5 showed the device performance of 5.43% (V_OC 723 mV, J_SC 9.3 mA cm⁻², ff 80%). The decreased device performance for the dye SQ5S has been attributed to the favorable intersystem crossing process associated with the photoexcited SQ5S that reduces the driving force for the charge injection process.     

Synthesis and photovoltaic properties of copolymers with a fluoro quinoxaline unit

Two novel accepter units, namely, difluoroquinoxaline and monofluoroquinoxaline, were prepared and used for the synthesis of the conjugated polymers containing electron donor–acceptor pairs for use in organic photovoltaics. The introduction of a fluorine atom into the quinoxaline moiety resulted in polymers with lowered highest occupied molecular orbital (HOMO) energy levels; this increased the open circuit voltage of the devices based on the synthesized polymers. The conjugated polymers containing difluoroquinoxaline and monofluoroquinoxaline, namely, thiophene and benzodithiophene, were synthesized using the Stille polymerization reaction to produce PEHBQxF2, PEHBQxF1, PEHBDTQxF2, and PEHBDTQxF1. The HOMO energy levels of PEHBQxF2, PEHBQxF1, PEHBDTQxF2, and PEHBDTQxF1 were determined to be −5.66, −5.52, −5.54, and −5.39 eV, respectively. The device with PEHBDTQxF2/PC₇₁BM (1:2, w/w) and containing diiodooctane (3 vol %) exhibited the best photovoltaic performance, with its V_OC being 0.79 V, J_SC being 10.44 mA/cm², FF being 68%, and PCE being 5.58%. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 821–830     

Synthesis and characterization of a wide-bandgap polymer based on perfluorinated and alkylthiolated benzodithiophene with a deep highest occupied molecular orbital level for organic photovoltaics

A perfluorinated and alkylthiolated benzodithiophene (BDT)-ttTPD-based donor polymer (P2FS-ttTPD) was synthesized via a Stille polymerization, and found to have a number average molecular weight (M_n) of 13,000 g/mol (Đ = 2.3). P2FS-ttTPD has a wide bandgap (1.96 eV) and a deep highest occupied molecular orbital (HOMO) level (−5.70 eV). The perfluorination and alkylthiolation of the polymer backbone lower the polymer's HOMO level significantly. The hole and electron mobilities of P2FS-ttTPD were determined to be 1.12 × 10⁻⁴ and 9.38 × 10⁻⁷ cm²/V s, respectively. Polymer solar cell devices prepared with a P2FS-ttTPD:IT-4F (1:1) blend as the active layer were found to exhibit power conversion efficiencies of 4.15%, a short-circuit current density (J_SC) of 10.29 mA/cm², an open-circuit voltage (V_OC) of 0.97 V, and a fill factor of 41.6%. The (1:1) blend devices were found to exhibit high V_OC and low E_loss values.     

Enhanced Performance of Organic Photovoltaic Cells Fabricated with a Methyl Thiophene‐3‐Carboxylate‐Containing Alternating Conjugated Copolymer

A new donor‐acceptor copolymer, containing benzodithiophene (BDT) and methyl thiophene‐3‐carboxylate (3MT) units, is designed and synthesized for polymer solar cells (PSCs). The 3MT unit is used as an electron acceptor unit in this copolymer to provide a lower highest occupied molecular orbital (HOMO) level for obtaining polymer solar cells with a higher open‐circuit voltage (V_OC). The resulting bulk heterojunction PSC made of the copolymer and [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM) exhibits a power conversion efficiency (PCE) up to 4.52%, a short circuit current (J_SC) of 10.5 mA·cm‐², and a V_OC of 0.86 V.     

Cyclometalated Ruthenium(II) Complexes Featuring Tridentate Click‐Derived Ligands for Dye‐Sensitized Solar Cell Applications

A series of heteroleptic bis(tridentate) Ru^II complexes featuring N^C^N‐cyclometalating ligands is presented. The 1,2,3‐triazole‐containing tridentate ligands are readily functionalized with hydrophobic side chains by means of click chemistry and the corresponding cyclometalated Ru^II complexes are easily synthesized. The performance of these thiocyanate‐free complexes in a dye‐sensitized solar cell was tested and a power conversion efficiency (PCE) of up to 4.0 % (J_sc=8.1 mA cm^?2, V_oc=0.66 V, FF=0.70) was achieved, while the black dye ((NBu₄)₃[Ru(Htctpy)(NCS)₃]; Htctpy=2,2′:6′,2′′‐terpyridine‐4′‐carboxylic acid‐4,4′′‐dicarboxylate) showed 5.2 % (J_sc=10.7 mA cm^?2, V_oc=0.69 V, FF=0.69) under comparable conditions. When co‐adsorbed with chenodeoxycholic acid, the PCE of the best cyclometalated dye could be improved to 4.5 % (J_sc=9.4 mA cm^?2, V_oc=0.65 V, FF=0.70). The PCEs correlate well with the light‐harvesting capabilities of the dyes, while a comparable incident photon‐to‐current efficiency was achieved with the cyclometalated dye and the black dye. Regeneration appeared to be efficient in the parent dye, despite the high energy of the highest occupied molecular orbital. The device performance was investigated in more detail by electrochemical impedance spectroscopy. Ultimately, a promising Ru^II sensitizer platform is presented that features a highly functionalizable “click”‐derived cyclometalating ligand.     

Synthesis and photovoltaic properties of conjugated copolymers based on benzimidazole and various thiophene

A new accepter unit, dimethyl‐2H‐benzimidazole, was prepared and used for the synthesis of the conjugated polymers containing electron donor–acceptor pair for organic photovoltaics (OPVs). Dimethyl‐2H‐benzimidazole unit was designed to substitute the BT unit of poly(N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)) (PCDTBT). A series of new semiconducting polymers with 2,2‐dimethyl‐2H‐benzimidazole, 9‐heptadecanyl‐9H‐carbazole, and thiophene (or bithiophene) units was synthesized using Stille polymerization to generate PCDTMBIs (or PCBBTMBIs). In dimethyl‐2H‐benzimidazole, the sulfur at 2‐position of BT unit was replaced with dialkyl substituted carbon, while keeping the 1,2‐quinoid form, to improve the solubility of the polymers. The absorption spectra of PCDTMBIs with thiophene units exhibit two maximum peaks at about 430 and 613–645 nm in solution. The solutions of PCBBTMBIs show two absorption peaks at about 445–456 and 630–645 nm which is red‐shifted about 20 nm when compared with PCDTMBIs caused by the introduction of bithiophene units. In most efficient polymer PCBBTMBI3, the device annealed at 100 °C for 10 min demonstrated a V_OC value of 0.60 V, a J_SC value of 4.31 mA/cm², and a FF of 0.35, leading to the power conversion efficiency (PCE) of 0.91%, under white light illumination (AM 1.5 G and 100 mW/cm²). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

New Conjugated Molecules with Two and Three Dithienyldiketopyrrolopyrrole (DPP) Moieties Substituted at meta Positions of Benzene toward p‐ and n‐Type Organic Photovoltaic Materials

Two conjugated molecules, TADPP3 and TADPP2‐TT , are reported, in which three and two dithienyldiketopyrrolopyrrole (DPP) moieties, respectively, are substituted at the meta positions of benzene. Based on cyclic voltammetry and absorption data, TADPP3 and TADPP2‐TT possess similar HOMO and LUMO energies of about ?5.2 and ?3.4 eV, respectively. Thin films of TADPP3 and TADPP2‐TT exhibit p‐type semiconducting behavior with hole mobilities of 2.36×10^?3 and 3.76×10^?4 cm² V^?1 s^?1 after thermal annealing. Molecules TADPP3 and TADPP2‐TT were utilized as p‐type photovoltaic materials to fabricate organic solar cells after blending with phenyl C₇₁ butyric acid methyl ester ( PC₇₁BM ) and phenyl C₆₁ butyric acid methyl ester ( PC₆₁BM ). The relatively low J_SC and fill factor values can be attributed to poor film morphologies based on AFM and XRD studies. A solar cell with a thin film of TADPP3 with PC₇₁BM in a weight ratio of 1:2 exhibits a high open‐circuit voltage (V_OC) of 0.99 V and a power conversion efficiency (PCE) of 2.47 %. Interestingly, TADPP3 can also be employed as an n‐type photovoltaic material. The blended thin film of TADPP3 with P3HT in a weight ratio of 1:2 gave a high V_OC of 1.11 V and a PCE of 1.08 % after thermal annealing.     

Molecular Engineering of Simple Phenothiazine‐Based Dyes To Modulate Dye Aggregation,Charge Recombination,and Dye Regeneration in Highly Efficient Dye‐Sensitized Solar Cells

A series of simple phenothiazine‐based dyes, namely, TP , EP , TTP , ETP , and EEP have been developed, in which the thiophene (T), ethylenedioxythiophene (E), their dimers, and mixtures are present to modulate dye aggregation, charge recombination, and dye regeneration for highly efficient dye‐sensitized solar cell (DSSC) applications. Devices sensitized by the dyes TP and TTP display high power conversion efficiencies (PCEs) of 8.07 (J_sc=15.2 mA cm^?2, V_oc=0.783 V, fill factor (FF)=0.679) and 7.87 % (J_sc=16.1 mA cm^?2, V_oc=0.717 V, FF=0.681), respectively; these were measured under simulated AM 1.5 sunlight in conjunction with the I^?/I₃^? redox couple. By replacing the T group with the E unit, EP ‐based DSSCs had a slightly lower PCE of 7.98 % with a higher short‐circuit photocurrent (J_sc) of 16.7 mA cm^?2. The dye ETP , with a mixture of E and T, had an even lower PCE of 5.62 %. Specifically, the cell based on the dye EEP , with a dimer of E, had inferior J_sc and V_oc values and corresponded to the lowest PCE of 2.24 %. The results indicate that the photovoltaic performance can be finely modulated through structural engineering of the dyes. The selection of T analogues as donors can not only modulate light absorption and energy levels, but also have an impact on dye aggregation and interfacial charge recombination of electrons at the interface of titania, electrolytes, and/or oxidized dye molecules; this was demonstrated through DFT calculations, electrochemical impedance analysis, and transient photovoltage studies.     

Synthesis and characterization of low‐bandgap copolymers based on dihexyl‐2h‐benzimidazole and cyclopentadithiophene

A series of new semiconducting polymers based on 4,4‐dihexyl‐4H‐cyclopenta[2,1‐b:3,4‐b′]dithiophene, 2,2‐dihexyl‐2H‐benzimidazole, and thiophene units was synthesized. The polymers show good solubility at room temperature in organic solvents owing to long alkyl chain in new acceptor, 2,2‐dihexyl‐2H‐benzimidazole. The advantage of dihexyl‐2H‐benzimidazole compared to the benzothiadiazole is to improve the solubility of the polymer. It was found that these polymers can finely be tuned for photovoltaic application by adjusting the contents ratio of the dihexyl‐2H‐benzimidazole unit. The spectra of the solid films show absorption bands with maximum peaks in the range of 421–577 nm and the absorption onsets at 588–683 nm, corresponding to band gaps of 2.11–1.82 eV. The devices with PCPDTDTHBI‐1 :PC₇₁BM showed an open‐circuit voltage (V_OC) of 0.46 V, a short‐circuit current density (J_SC) of 3.83 mA/cm², and a fill factor of 0.36, giving a power conversion efficiency of 0.64%. Decrease of the dihexyl‐2H‐benzimidazole contents in the polymers induced red‐shift of the UV absorptions, and increased V_OC and J_SC values, to improve the efficiency of organic photovoltaics. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Conjugated polymer consisting of dibenzosilole and quinoxaline as donor materials for organic photovoltaics

The new D–A type polymers poly(dibenzosilole-diphenylquinoxaline) (PSiPDTQ) and dibenzosilole-dibenzophenazine) (PSiFDTQ), both of which adopted benzosilole as a donor, were polymerized through a Suzuki coupling reaction. PSiPDTQ and PSiFDTQ were able to be dissolved in organic solvents and exhibited high thermal stability. Due to the appropriate LUMO energy levels, an effective charge transport was observed in PSiPDTQ and PSiFDTQ. According to X-ray diffraction measurements, a single broad diffraction peak was detected at approximately 20.5°. The π–π stacking distances (d_π) for PSiPDTQ and PSiFDTQ were 4.4 and 4.3 Å, respectively. When PSiPDTQ and PC₇₁BM were blended in a 1:3 ratio and used as the active layer in a solar cell, the resulting V_oc, J_sc, FF and PCE were 0.89 V, 5.1 mA/cm², 30.2% and 1.4%, respectively. For solar cells using a 1:6 ratio of PSiFDTQ to PC₇₁BM, the resulting V_oc, J_sc, FF and PCE were 0.98 V, 3 mA/cm², 52.8% and 1.6%, respectively. In addition, for a PSiPDTQ and PC₇₁BM blended film (1:3 ratio) with an additional layer of PFN, the PCE of the resulting solar cells was improved (relative to solar cells without PFN) to 2.1% due to the interfacial adhesion of PFN.     

钛掺杂钙钛矿制备高效率钙钛矿太阳能电池

采用钛离子掺杂钙钛矿薄膜的方法修饰钙钛矿晶界缺陷。研究表明钛离子富集在晶界处,有效地钝化了晶界缺陷,同时有助于连续、平整、高质量薄膜的形成。经过钛离子掺杂后的钙钛矿太阳能电池电流(JSC)达到22.3 mA·cm~(-2),开路电压(VOC)达1.1 V,填充因子(FF)高达72.4%,光电转换效率(PCE)优化至17.4%,远高于未掺杂钙钛矿太阳能电池。     

A New D–A conjugated polymer P(PTQD‐BDT) with PTQD acceptor and BDT donor units for BHJ polymer solar cells application

A novel donor–acceptor ( D–A ) copolymer comprising of weak electron donating BDT moiety and strong 9‐(2‐octyldodecyl)?8H‐pyrrolo[3,4‐b] bisthieno[2,3‐f:3',2'‐h] quinoxaline‐8,10(9H)‐dione (PTQD) unit denoted as P(PTQD‐BDT) was synthesized as donor material for polymer solar cells. P(PTQD‐BDT) shows a broad visible‐near‐infrared absorption band with an optical bandgap of 1.74 eV and possesses a relatively low‐lying HOMO level at ?5.28 eV. Bulk‐heterojunction polymer solar cell with the optimized blend of 1:2 (weight ratio) P(PTQD‐BDT):PC₇₁BM (processed with chloroform) shows an open circuit voltage of 0.92 V, a short circuit current density of 7.84 mA/cm², and a fill factor of 0.50, achieving a power conversion efficiency (PCE) of 3.61%. The PCE has been further improved to 5.55 % (J_sc = 10.34 mA/cm², V_oc = 0.88V and FF = 0.61), when 3% v ol 1,8‐diio‐dooctane (DIO) was used as solvent additive for the processing of P(PTQD‐BDT):PC₇₁BM blended film. The enhancement in J_sc is as a result of the appropriate morphology and efficient exciton dissociation into free charge carrier. The increase in PCE has been attributed to the favorable nanoscale morphology for efficient exciton dissociation and charge transport (reduction in the electron to hole mobility ratio). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2390–2398     

Dihydrophenazine-based double-anchoring dye for dye-sensitized solar cells

A novel dihydrophenazine-based organic di-anchoring dye DK-11 was synthesized by utilizing a simple synthetic protocol. The dye was characterized by optical and electrochemical studies and used as a sensitizer for dye-sensitized solar cell. The proposed butterfly structure was supported by IR experiments which ensured the binding of both carboxylic acid units on the semiconductor surface. Using the dye DK-11 , the device generated an efficiency of 5.07% with J_SC, V_OC, and FF values of 10.65 mA/cm², 0.67 V, and 0.71, respectively.     

D–π–A–π–A Strategy to Design Benzothiadiazole–carbazole‐based Conjugated Polymer with High Solar Cell Voltage and Enhanced Photocurrent

The theoretical calculations are used to find that D–π–A–π–A style conjugated polymer PC‐TBTBT is more efficient for solar cells application than the D–π–A analog PC‐TBT because the D–π–A–π–A structure has a narrower band gap and higher molar absorption coefficient and redshift spectrum. Motivated by the theoretical prediction, 5,6‐bis(octyloxy)‐2,1,3‐benzothiadiazole and 2,7‐carbazole are adopted to synthesize the D–π–A–π–A style PC‐TBTBT (M_w = 31.1 kDa) and D–π–A analog PC‐TBT (M_w = 87.5 kDa) by Suzuki coupling reaction. Experimental results confirm that D–π–A–π–A PC‐TBTBT ‐based solar cell shows a power conversion efficiency (PCE) of 4.74% with high V_OC of 0.99 V and enhanced J_SC of 9.70 mA cm⁻². The PCE and J_SC achieve improvements of 17% and 26%, respectively, compared to the D–π–A PC‐TBT ‐based solar cell.

     

Fused structures in the polymer backbone to investigate the photovoltaic and electrochromic properties of donor–acceptor‐type conjugated polymers

In this study, two new benzotriazole (BTz) and dithienothiophene (DTT) containing conjugated polymers were synthesized. After successful characterizations of the monomers by proton‐nuclear magnetic resonance (¹H NMR) and carbon‐NMR (¹³C NMR) techniques, poly(4‐(dithieno[3, 2‐b:2′,3′‐d]thiophen‐2‐yl)‐2‐(2‐octyldodecyl)‐2H‐benzo[d][1,2,3] triazole) P1 and poly(4‐(5‐(dithieno[3,2‐b:2′,3′‐d]thiophen‐2‐yl)thiophen‐2‐yl)‐2‐(2‐octyldodecyl)‐7‐(thiophen‐2‐yl)‐2H‐benzo[d][1,2,3]triazole) P2 were synthesized via a typical Stille coupling. Electrochemical and spectroelectrochemical studies showed that both polymers can be multipurpose materials and used in electrochromic and photovoltaic applications. Reported study indicated that incorporation of DTT into the structure leads to fast switching times compared with BTz‐based polymers and competent percentage transmittance in the near‐infrared region. Multichromism is important in the context of low‐cost flexible display device technology and both polymers are ambipolar and processable as well as multichromic. Throughout the preliminary photovoltaic studies, the best performances of photovoltaic devices were found as V_oc = 0.49 V, J_sc = 0.83 mA/cm², fill factor (FF) = 34.4%, and power conversion efficiency (PCE) = 0.14% for P1 , and as V_oc = 0.35 V, J_sc = 1.57 mA/cm², FF = 38.2%, and PCE = 0.21% for P2 . © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013