利用双水相体系的温度诱导效应萃取甘草酸

利用双水相分配技术结合温度诱导效应提取甘草酸，研究甘草酸单铵盐在环氧乙烷－环氧丙烷共聚物（EOPO）／混合磷酸钾（KHP）体系中的分配行为，通过实验确定了最佳体系：EOPO L64浓度为28（wt)%，K2HPO4浓度为32（wt）％。甘草酸单铵盐最大总收率达68.4%，为工业上采用双水相技术提取干草酸提供了一种新途径。     

Aqueous two-phase extraction as an effective tool for isolation of geniposide from gardenia fruit

Natural products are normally obtained by organic solvent extraction and many subsequent chromatographic separations. Compounds of interest are often isolated with very low yield and limited purity. An aqueous two-phase extraction process combined with a simple ethanol treatment, for removing excess inorganic salt, has been developed for preparation of geniposide from gardenia. The system was comprised of PE62, a random copolymer composed of 20% ethylene oxide and 80% propylene oxide, KH2PO4 and ethanol. To find optimal conditions, the partition behavior of geniposide under an aqueous two-phase system was investigated. Various factors were considered, including the concentration of salt, the concentration of polymer, the sample loading, and the addition of ethanol. The experimental results demonstrated that increasing salt concentration or decreasing PE62 concentration results in enhancement of the geniposide partition in the salt-rich phase. The addition of ethanol and higher sample loading also promoted the partition efficiency of geniposide. Based on this study, an optimized system containing 5% PE62, 7.5% KH2PO4, and 10% ethanol was tested on a large-scale extraction. A 39.0-g aliquot of final product (in powder form) with 77% purity of geniposide can be effectively extracted from 500 g of gardenia fruit. This process is proved to be useful for industrial application of geniposide preparation.     

环氧乙烷环氧丙烷开环聚合反应动力学研究

环氧乙烷和环氧丙烷由于具有较高的环张力,因而容易发生开环聚合。本文综述了环氧乙烷合环氧丙烷开环聚合反应的动力学研究进展,考察了环氧乙烷和环氧丙烷开环聚合反应的机理,分别讨论了各类催化剂体系中环氧乙烷和环氧丙烷开环聚合的动力学常数、两者的竞聚率及开环聚合产物的分子量分布,并指出了开环聚合反应动力学研究对于环氧乙烷和环氧丙烷的开环聚合研究及工业应用的重要性。     

Dynamic elasticity of triblock copolymer of poly(ethylene oxide) and poly(propylene oxide) on a water surface

Dilatational viscoelasticity of adsorbed and spread films of the poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymer at the air-water interface is studied by the capillary waves and oscillating barrier techniques. At the surface pressure below 10 mN/m, dynamic surface properties of these films coincide with those of poly(ethylene oxide). At higher surface pressures, the results obtained indicate the desorption of poly(propylene oxide) segments from the monolayer and their interaction with poly(ethylene oxide) segments in an aqueous phase. At a surface pressure close to 19 mN/m, the behavior of adsorbed and spread poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) films becomes different. The real part of dynamic surface elasticity of spread films tends toward its maximum value (20 mN/m) and, upon further compression, films begin to dissolve. At the same time, the surface elasticity of adsorbed films decreases nearly twofold upon the achievement of the maximum value that testifies the formation of looser structure of the surface layer.     

Cutinase-peptide fusions in thermoseparating aqueous two-phase systems. Prediction of partitioning and enhanced tag efficiency by detergent addition

It is of increasing importance to develop efficient purification methods for recombinant proteins where the number of steps can be minimised. The aim has been to establish a method for predicting the partitioning of the wild-type target protein in an aqueous two-phase system, and with this as basis, develop fusion tags and optimise the phase system for enhanced partitioning of the target protein. The surface of the lipolytic enzyme cutinase from Fusarium solani pisi was investigated with a computer program, Graphical Representation and Analysis of Surface Properties (GRASP). The accessible surface areas for the different amino acid residues were used together with peptide partitioning data to calculate the partition coefficient for the protein. The separation system was composed of a thermoseparating random copolymer of ethylene oxide and propylene oxide. Breox PAG 50A 1000, as top phase forming polymer and a hydroxypropyl starch polymer, Reppal PES 200, as bottom phase polymer. The calculated partition coefficient for the wild-type protein (K= 1.0) agreed reasonably well with the experimentally determined value (K=0.85). Genetic engineering was used to construct fusion proteins expressed in Saccharomyces cerevisiae based on cutinase and peptide tags containing tryptophan, to enhance the partitioning in aqueous two-phase systems. The partitioning of the cutinase constructs could qualitatively be predicted from peptide partitioning data, i.e. the trends in partitioning could be predicted. A spacer peptide introduced between protein and tag increased the partitioning of the protein towards the ethylene oxide-propylene oxide (EOPO) copolymer top phase. The aqueous two-phase system was modified by addition of detergent to increase the partitioning of the cutinase variants towards the EOPO copolymer phase. Triton and a series of C12En detergents selectively increased the partitioning of cutinase constructs with (WP)4-based tags up to 14 times compared to wild-type cutinase. The protein partition could almost quantitatively be predicted from the peptide partition data.     

Alternative total synthesis of (+)-aspicilin

The total synthesis of an 18-membered polyhydroxylated macrolide (+)-Aspicilin was accomplished starting from commercially available enantiopure propylene oxide and D-(+)-gluconolactone by asymmetric synthetic approach. The key reactions involved are Witttig reaction, Sharpless asymmetric dihydroxylation, and Yamaguchi macrolactonization.     

Effects of organic solvents on the partitioning of enzymes in aqueous two-phase systems

Organic solvents (ethylene glycol, glycerol, dimethyl sulphoxide, dimethylformamide, dioxane, methanol and propanol-2, as well as sucrose and urea) have been included in aqueous two-phase (liquid-liquid) systems comprised of water, dextran and poly(ethylene glycol). The concentration of the organic solvent was in most cases 20% (w/w). The influence of these solvents on the phase-forming properties, the volume ratio, the freezing point and the partitioning of a polymer-bound ligand, Procion Red HE-3B poly(ethylene glycol), has been studied. The partition coefficients for alkaline phosphatase decrease with ethylene glycol, glycerol, sucrose and urea (factors of 0.25-0.5), but increase with the other substances (factors of 1.2-1.6). The temperature effects on the partitioning of alkaline phosphatase from calf intestine as well as of phosphofructokinase from yeast in systems containing ethylene glycol have been studied and compared with partitioning in standard systems, not containing solvents. The possible uses of the above systems for partitioning studies of enzymes are discussed.     

Purification of human immunoglobulin G by thermoseparating aqueous two-phase systems

The purification of human immunoglobulin G (IgG) from a Chinese hamster ovary (CHO) cells supernatant was studied using an aqueous two-phase system (ATPS) composed of ethylene oxide/propylene oxide (UCON) and dextran. In UCON/dextran systems IgG partitions preferentially to the less hydrophobic dextran-rich phase (Kp<1). The addition of triethylene glycol-diglutaric acid (TEG-COOH) shifted the IgG partition into the upper phase showing significant improvements in both the recovery yields and purity. The purification of IgG from a CHO cell supernatant with UCON 2000/dextran/TEG-COOH system was optimised using a central composite design. Using an ATPS composed of 8% UCON, 6% dextran and 20% TEG-COOH, IgG was purified, in two steps, with a global yield of 85% and 88% purity. Statistical valid models were obtained to predict the effect of the experimental conditions on the IgG yield and purity, for both extraction and back-extraction steps. A system composed of 10% UCON, 5.5% dextran and 20% TEG-COOH was identified as the best compromise between final purity and yield.     

Temperature-dependent aggregation and disaggregation of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer in aqueous solution

Aggregation and disaggregation of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) block copolymers, Pluronics P103 and P104, in aqueous solutions during a heating and cooling cycle were investigated by dynamic laser scattering (DLS) and 1H NMR spectroscopy. Temperature hysteresis was observed by DLS when cooling the copolymer aqueous solutions because larger aggregates existed at temperatures lower than critical micellization temperature (CMT), but no temperature differences were observed by NMR. This phenomenon was explained as the forming of water-swollen micelles at temperatures lower than CMT during the cooling process.     

Intermolecular interactions governing solubilization in micelles of poly(alkylene oxide) surfactants

Partition coefficients for 39 low-molecular-mass compounds between water and micelles of an ethylene oxide-propylene oxide block copolymer (Pluronic P85) and the monolauryl ether of poly(ethylene oxide) (Brij 35) have been measured by the methods of fluorescence spectroscopy, fluorescence anisotropy, and dialysis kinetics. The tested compounds include aromatic hydrocarbons, phenols, naphthols, xanthene dyes, anthracycline antibiotics, and porphyrins. The multifactor analysis of the partition coefficients in terms of the linear free-energy relationships has been performed. It has been shown that the H-donating ability of compounds facilitates their solubilization in Pluronic micelles and has no effect on solubilization in micelles of monolauryl ether of poly(ethylene oxide). This difference indicates that, when solubilization occurs in Pluronic micelles, the compounds under study appear in a hydrophobic core composed of poly(propylene oxide) blocks.     

Phase equilibrium and macrolide antibiotics partitioning in real water samples using a two-phase system composed of the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate and an aqueous solution of an inorganic salt

An ionic liquid-salt aqueous two-phase system (ILATPS) based on the hydrophilic ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim]BF₄) and inorganic salt was developed for direct separation and analysis of macrolide antibiotics coupled with molecular fluorescence spectrophotometry. Liquid–liquid equilibria of [Bmim]BF₄-salt aqueous two-phase systems were studied for different salts and temperatures. It was found that the salting-out ability of different salts may be related to the Gibbs energy of hydration of the ions, and the two-phase area was expanded with a decrease in temperature. The partition coefficients as well as extraction efficiencies of azithromycin and mydecamycin in [Bmim]BF₄-salt aqueous two-phase system were influenced by the types of salts, concentration of salt, and the extracting temperature. Under the optimum conditions, the average partition coefficient of azithromycin in [Bmim]BF₄-Na₂CO₃ ILATPS was 162, and that of mydecamycin in [Bmim]BF₄- NaH₂PO₄ ILATPS was 90.9. This method has been satisfactorily applied to the determination of azithromycin and mydecamycin in real water samples with detection limits of 0.059 µg mL^?1 and 0.019 µg mL^?1. This extraction method is a simple, non-toxic and effective sample pretreatment technique with promise also for the separation of other small biomolecules.     

Enantioselective total synthesis of β-zearalenol from (s)-propylene oxide

The total synthesis of 14-membered resorcylic acid macrolide, β-zearalenol, was accomplished starting from commercially available enantiomerically pure propylene oxide and methyl 2,4-dihydroxy-6-methylbenzoate using Grignard reaction, asymmetric dihydroxylation, Yamaguchi macrolactonization, and ring-closing metathesis as key steps.     

A new extraction method for the preparation of zinc oxide nanoparticles in aqueous two-phase systems

An extraction method was suggested for the preparation of differently shaped nano- and micrometer- sized zinc oxide particles at the interface boundary of aqueous two-phase systems based on polyethylene glycol (polyethylene oxide) and sodium sulfate using NaOH and aqueous ammonia as precipitating agents.     

Effect of sodium chloride on association behavior of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer in aqueous solutions

The effect of sodium chloride (NaCl) upon the thermally induced association behavior of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) block copolymer, Pluronic P103, has been investigated using pyrene fluorescence spectroscopy. The critical micellization temperature (CMT) of Pluronic P103 in aqueous solution is decreased by the addition of NaCl. The standard enthalpy and entropy of micellization for Pluronic P103 in water are increased in the presence of small amounts of NaCl, but further addition of NaCl decreases the standard enthalpy and entropy of micellization. The I1/I3 ratio of pyrene in aqueous Pluronic P103 solutions at temperature below the CMT decreases with increases of NaCl concentration, which is related to the decrease of PPO solubility. The decrease in polarity of the PPO shifts the CMT toward lower temperature.     

Purification of protein and recycling of polymers in a new aqueous two-phase system using two thermoseparating polymers

In this study we present a new aqueous two-phase system where both polymers are thermoseparating. In this system it is possible to recycle both polymers by temperature induced phase separation, which is an improvement of the aqueous two-phase system previously reported where one of the polymers was thermoseparating and the other polymer was dextran or a starch derivative. The polymers used in this work are EO50PO50, a random copolymer of 50% ethylene oxide (EO) and 50% propylene oxide (PO), and a hydrophobically modified random copolymer of EO and PO with aliphatic C14H29-groups coupled to each end of the polymer (HM-EOPO). In water solution both polymers will phase separate above a critical temperature (cloud point for EO50PO50 50 degrees C, HM-EOPO, 14 degrees C) and this will for both polymers lead to formation of an upper water phase and a lower polymer enriched phase. When EO50PO50 and HM-EOPO are mixed in water, the solution will separate in two phases above a certain concentration i.e. an aqueous two-phase system is formed analogous to poly(ethylene glycol) (PEG)/dextran system. The partitioning of three proteins, bovine serum albumin, lysozyme and apolipoprotein A-1, has been studied in the EO50PO50/HM-EOPO system and how the partitioning is affected by salt additions. Protein partitioning is affected by salts in similar way as in traditional PEG/dextran system. Recombinant apolipoprotein A-1 has been purified from a cell free E. coli fermentation solution. Protein concentrations of 20 and 63 mg/ml were used, and the target protein could be concentrated in the HM-EOPO phase with purification factors of 6.6 and 7.3 giving the yields 66 and 45%, respectively. Recycling of both copolymers by thermoseparation was investigated. In protein free systems 73 and 97.5% of the EO50PO50 and HM-EOPO polymer could be recycled respectively. Both polymers were recycled after aqueous two-phase extraction of apolipoprotein A-1 from a cell free E. coli fermentation solution. Apolipoprotein A-1 was extracted to the HM-EOPO phase with contaminating proteins in the EO50PO50 phase. The yield (78%) and purification factor (5.5) of apolipoprotein A-1 was constant during three polymer recyclings. This new phase system based on two thermoseparating polymers is of great interest in large scale extractions where polymer recycling is of increasing importance.     

Extraction of plasmid DNA from Escherichia coli cell lysate in a thermoseparating aqueous two-phase system

The primary purification of a 6.1 kilo base pair (kbp) plasmid from a desalted alkaline lysate has been accomplished by a thermoseparating aqueous two-phase system [(50% ethylene oxide-50% propylene oxide)-Dextran T 500]. The partitioning of the different nucleic acids (plasmid DNA, RNA, genomic DNA) in the thermoseparating aqueous two-phase system was followed both qualitatively by agarose gel electrophoresis and quantitatively by analytical chromatography (size exclusion- and anion-exchange mode) and PicoGreen fluorescence analysis. The experimental results showed a complete recovery of the plasmid DNA to the top phase, while 80% of total RNA and 58% of total protein was discarded to the bottom phase. Moreover, a 3.8-fold volume reduction of the plasmid DNA solution was achieved. By using a final thermoseparating step, the EO50PO50 polymer could be efficiently recycled, resulting in plasmid solution containing less than 1% polymer. The developed thermoseparating aqueous two-phase system shows great potential for the large-scale processing of plasmid DNA.     

聚乙二醇-硫酸铵双水相萃取次甲基蓝的研究

利用分光光度法研究了次甲基蓝在聚乙二醇-硫酸铵双水相体系的萃取行为,探索了质量配比(mPEc/m(NH4)2SO4)、温度和次甲基蓝的浓度对双水相及次甲基蓝萃取率(Y)的影响.实验表明:(1)在一定的温度和浓度下,随着mPEC/m(NH4)2SO4的减小,分配系数K( cup/clow)增加,萃取率Y略有减小;(2)在一定的质量配比和浓度下,分配系数K(cup/clow)随温度的升高而增大,但萃取率Y却基本保持不变;(3)在一定的质量配比和温度下,随着次甲基蓝浓度的增加,分配系数K(cup/clow)增大;萃取率Y略有增加.在mPEG/m( NH4) 2SO4为1.50∶1,c次甲基蓝=8.915×10-5mol/L、t=30℃的实验条件下,K(cup/clow)=22.14,萃取率(y)可达95.43％.     

New phase supports for partition chromatography of biopolymers

Liquid-liquid partition chromatography of bio-polymers requires aqueous two-phase systems for reasons of sample solubility and stability. Such aqueous two-phase systems form when thermodynamically incompatible polymers are co-dissolved in water. The most common polymer combination providing a two-phase system at reasonably low polymer concentrations is the combination of poly(ethylene glycol) (“PEG”) and dextran (“DX”), detected and introduced for the separation of biopolymers and cells by Albertsson about 30 years ago. The application of this powerful system for liquid-liquid partition chromatography requires support materials with surfaces able to immobilize selectively one of the two aqueous phases. This phase immobilisation may be achieved by exploiting incompatibilities between the polymers dominating in the phases and the hydrated support surface. Examples involving diol-modified silica and polyacrylamide coated diol-silica as support materials in aqueous PEG-DX and PEG-salt systems are presented. The application of such systems for the separation of biopolymers is demonstrated.     

Synthesis of new 14-membered macrolide antibiotics via a novel ring contraction metathesis

[reaction: see text] A novel ring opening ring closing metathesis (ROM-RCM) was demonstrated for cyclic conjugated dienes, effecting the excision of a C(2)H(2) unit and a net ring contraction. Applying the ring contraction metathesis, new 14-membered ring macrolide antibiotics were synthesized in a single step from existing 16-membered ring macrolides. This new class of macrolide antibiotics will provide access to new therapeutics for the treatment of macrolide-resistant bacterial infections.     

Application of centrifugal counter-current chromatography to the separation of macrolide antibiotic analogues. I. Selection of solvent systems based on solubility and partition coefficient investigations

As the first part of our studies on counter-current chromatography, the methodology for selecting suitable solvent systems was established based on detailed investigations of solubility and partition coefficients (log K) of macrolide antibiotic analogues. The solubility of two important macrolides, ascomycin and FK-506, was measured in a series of common solvents, where their polarities were ranked with dielectric constants. The partition coefficients of the two macrolides were compared in various binary, ternary, quaternary solvent systems. Hexane-tert.-butyl methyl ether-methanol-water system was selected based on suitable log K of solutes and hydrogen-bonding properties of solvents. In the further optimisation of composition proportions in the multicomponent solvent system, hexane-tert.-butyl methyl ether-methanol-water (1:3:6:5) showed the best solvent selectivity by giving the most prominent difference of partition coefficient (delta log K) between ascomycin and FK-506. With this solvent system, a baseline preparative separation of these two very closely related 23-membered macrolide antibiotics was successfully achieved by employing the newly introduced Quattro counter-current chromatograph.