分子动力学模拟研究外电场对咪唑类离子液体振动谱的影响（英文）

本文利用分子动力学模拟研究了外电场对咪唑类离子液体1-乙基-3-甲基咪唑六氟磷酸盐(EMIMPF6)从0到4000cm~(-1)范围内振动谱的影响。研究结果表明,在没有外电场时利用分子动力学模拟计算得到的从400到4000 cm~(-1)的振动带可以重现实验测得的谱。当外电场从0到9 V?nm~(-1)变化时,在50.0和199.8 cm~(-1)处的振动带强度持续增强然后趋于饱和,而从400到4000 cm~(-1)的振动带强度明显减弱并最终消失。此外,在外电场从0变到2 V?nm~(-1)时,50.0 cm~(-1)的振动带红移了16.7 cm~(-1),然后当外电场变化到3 V?nm~(-1)及更大时,该振动带红移增大到33.3 cm~(-1)。在外电场从0变到3 V?nm~(-1)时,3396.6 cm~(-1)的振动带红移大约16.7 cm~(-1),然后当外电场增大到4 V?nm~(-1)甚至更大时,该振动带红移33.3 cm~(-1),但是从0到4000 cm~(-1)的其他振动带的位置几乎没有变化。基于对模拟结果和先前报道文献的进一步分析,对于50.0 cm~(-1)的振动带,增加的外电场增强了阳离子和阴离子之间的极性使阳离子和阴离子间的偶极矩增大,因此该振动带的强度不断增大然后达到饱和。对于199.8 cm~(-1)的振动带增加的外电场增强了乙基链的扭转,使该振动带的强度增大并达到饱和。对于从400到4000 cm~(-1)的其他振动带,增加的外电场使EMIMPF_6中的阳离子和阴离子的取向更一致,并且可以推测这种更一致的取向可能会削弱振动带的强度甚至使它们消失。50.0 cm~(-1)处振动带的红移可能是由于外电场破坏了EMIMPF_6内部的静电场分布进而减弱了阳离子和阴离子间的相互作用。3396.6 cm~(-1)处振动带的红移可归功于外电场减弱了氮原子与阳离子咪唑环上酸性氢原子间形成的氢键的拉伸振动。对于其他的振动带,由于官能团固有的拉伸、弯曲、转动振动不受外电场的影响,外电场没有改变振动带的位置。     

密度泛函理论模拟外电场对铁氧体电子结构的影响

通过密度泛函理论(DFT)模拟了3种典型的铁氧体(Fe₂O₃、Fe₃O₄和α-FeOOH)受外电场作用下的电子结构,研究了外电场对不同铁氧体电子结构的影响。DFT模拟结果显示:外电场的存在能够有效提高Fe₂O₃、Fe₃O₄和α-FeOOH晶体结构的价带位置,从而导致3种铁氧体的带隙出现明显的降低;当外电场强度为0.01 V·nm^-1时,Fe₂O₃、Fe₃O₄和α-FeOOH的带隙分别降低了0.36、0.12和0.34 eV;当电场增大至0.1 V·nm^-1时,Fe₂O₃晶体出现击穿现象,Fe—O化学键断裂导致Fe原子的电子沿外电场方向高度离域至相邻Fe原子,而Fe₃O₄和α-FeOOH则仅出现不同...     

二氧化钛分子电致发光激发特性研究

采用密度泛函B3P86方法优化得到了沿分子平面不同外电场作用下TiO₂分子的基态稳定构型, 在优化构型下利用杂化CIS (CI-Singles)-B3P86方法在6-311＋G*基组水平上, 研究了不同外电场下TiO₂分子前六个激发态的激发能和跃迁波长等激发特性. 研究结果表明, TiO₂分子多个激发态满足偶极跃迁定则, 跃迁光谱对应多个峰值, 在分子水平上, 可以增大利用太阳光的比例. 在外电场作用下, 能隙随电场的增大而减小, 电子易从最高占据轨道跃迁到最低空轨道形成空穴, 各个激发态跃迁波长均有随电场增大发生红移的趋势, 最长589 nm, 因而利用外电场可以控制材料的发光光谱范围在可见光区域扩展.     

MoP-NC纳米球负载Pt纳米粒子用于高效甲醇电解

实现绿色甲醇电解制氢需要高效的双功能催化剂。本文采用热处理结合乙二醇还原法成功制备了MoP-NC纳米球负载的超细Pt纳米粒子(平均粒径为2.53 nm)复合催化剂(Pt/MoP-NC)用于高效甲醇电解制氢。MoP-NC纳米球不仅能提高Pt纳米粒子的分散性并且增强Pt的抗中毒能力。电化学测试表明Pt/MoP-NC催化剂在酸性甲醇氧化反应(MOR)和析氢反应(HER)中具有较高的催化性能;其中,MOR的正向扫描峰值电流密度为90.7 mA∙cm⁻²,是商业Pt/C催化剂的3.2倍,在10 mA∙cm⁻²的电流密度下,HER的过电位低至30 mV,与商业Pt/C接近。由Pt/MoP-NC||Pt/MoP-NC组装的两电极电解槽驱动10 mA∙cm⁻²的电流密度仅需要0.67 V的电压,比相同条件下电解水的电压低1.02 V,大大降低了能量输入。Pt/MoP-NC的高催化性能主要来源于Pt活性中心与相邻层状多孔球形结构的MoP-NC载体之间电子效应及配体效应引起的抗一氧化碳中毒能力的提升和含氧物种的容易生成。     

溶液浓度对拉曼光谱线宽和频移影响的实验研究

将液芯光纤技术用于傅里叶变换拉曼光谱测量中,提高拉曼光谱强度10²～10⁴倍.应用该技术,在实验上研究了溶液浓度变化对β-carotene,rhodamine在CS²中的CC键π-π^*跃迁拉曼线频移和线宽的影响.实验结果表明,随着浓度降低(1×10^-7～1×10^-12mol/L),拉曼光谱线峰值发生红移,线宽变窄.     

NaNO3和NaClO4在N,N-二甲基甲酰胺中的离子溶剂化

利用红外光谱研究了NaNO₃和NaClO₄在N,N-二甲基甲酰胺(DMF)溶剂中发生离子-溶剂和离子-离子的相互作用, 分析结果表明, DMF的OC-N谱带发生了明显的变化. 定量计算了在Na⁺浓度为0.22~1.24 mol/kg范围内的溶剂化数为1~4. 对谱图中酰胺基上C-N和CO的特征峰强度随Na⁺浓度变化的对比, 推测离子溶剂化作用导致DMF的酰胺基内部形成共轭键. 利用量子化学方法进行优化及热力学性质计算, 得到C-N键伸缩振动频率及红外光谱强度变化规律. 优化结构与实验结论相符合. 由NaNO₃的ν₂谱带及NaClO₄的ν₁谱带的解析得到溶液中阴离子缔合效应的一般规律, 并通过阴离子缔合特征峰与酰胺基上的N-C-N面外振动峰(865 cm^-1)的变化情况, 讨论了溶液中的离子溶剂化作用.     

阴离子对水的羟基伸缩振动拉曼光谱的影响

通过比较纯水、NaX(X=F, Cl, Br, I)、Na2S、NaOH、NaNO3、Na2CO3、Na2SO4溶液的羟基伸缩振动拉曼光谱, 发现所研究的阴离子对水的结构都有破坏作用. 通过比较阴离子对水的羟基伸缩振动拉曼光谱的影响, 可将所研究的阴离子分为两类, 一类阴离子有F−、OH−、S2−、CO32−, 另一类阴离子有Cl−、Br−、I−、NO3−和SO42−. 它们的主要区别在于对羟基伸缩振动拉曼光谱3600 cm−1、2900−3100 cm−1处影响不同, 产生这些区别的原因在于阴离子与水分子之间氢键的强弱. 阴离子对水的羟基伸缩振动拉曼光谱的影响因素有离子半径、离子电荷和离子结构, 它们的影响程度为离子结构>离子电荷>离子半径.     

新型氮杂18-冠-6衍生物的合成及其与阳离子的配位性能

通过1,10-二氧-4,7,13,16-四氮杂18-冠-6 (1)与2-羟基-5-硝基苄基溴反应合成了一个四硝基酚取代的氮杂18-冠-6衍生物(2). 采用UV-Vis光谱法研究了混合溶剂中冠醚2对H^＋, Mg^2＋, Ca^2＋, Sr^2＋, Ba^2＋和Pb^2＋的光谱响应及配位性能. 结果表明, 随溶液pH值的增大, 冠醚2的最大吸收峰由319 nm逐渐红移到426 nm, 并伴随着强度的增大; 其与几种阳离子形成配合物的稳定常数随阳离子半径的增加而增大, 从而展示了对Ba^2＋和Pb^2＋高的配位能力.     

N-(2,4-二硝基苯基)-N -取代苯腙衍生物对阴离子识别研究

合成了4种N-(2,4-二硝基苯基)-N -取代苯腙类阴离子结合受体(1～4, 取代基 R＝H, o-OCH₃, o-Cl, o-OH), 应用紫外吸收光谱方法研究了其与阴离子的相互作用, 以及考察N -苯环取代基对受体分子之阴离子亲合力和选择性的影响. 实验显示: 乙腈中F^－、CH₃CO 等阴离子使受体分子吸收光谱红移, 溶液由黄色转变为红色, 其中受体分子2对 F^－表现出高选择性的灵敏响应. 实验表明受体-阴离子间形成了氢键型超分子配合物, Job作图法给出了受体分子与阴离子的1∶1结合计量比, ¹H NMR滴定为受体分子与阴离子间的氢键作用本质提供了直接证据.     

十二烷基苯磺酸钠和无机阳离子之间相互作用的密度泛函理论研究

研究阴离子表面活性剂和阳离子之间的相互作用对于理解阴离子表面活性剂的沉淀和溶解现象具有十分重要的理论和实际意义,但关于两者相互作用的相关理论模型鲜有报道。本文采用密度泛函理论(DFT)方法研究了十二烷基苯磺酸根阴离子(DBS^-)与阳离子(Na⁺, Mg²⁺和Ca²⁺)在溶液内及气/液界面处的相互作用。在溶液内,在两种不同溶液环境中(水相和正十二烷)构建DBS^-/阳离子相互作用模型,并对其进行优化。结果表明, DBS^-能够与阳离子以双齿结构稳定结合。DBS^-与阳离子的结合能不仅取决于参与的无机盐离子种类,还与溶剂的性质有关。在气/液界面处, DBS^-与六个水分子相互作用形成的水合物DBS^-·6H₂O最为稳定。但是,无机盐离子的引入会严重破坏DBS^-·6H₂O水合物的水化层结构。本文定义无量纲参量def用来对水化层结构的变化程度进行评价。无机盐离子对DBS^-·6H₂O水化层结构破坏程度的顺序为:Ca²⁺ > Mg²⁺ >Na⁺。电荷分析结果表明水化层在十二烷基苯磺酸钠(SDBS)头基与阳离子的相互作用中起了重要作用。     

外电场作用下离子液体振动光谱变化的分子动力学模拟研究

Vibrational spectroscopy is a powerful tool for studying the microstructure of liquids, and anatomizing the nature of the vibrational spectrum (VS) is promising for investigating changes in the properties of liquid structures under external conditions. In this study, molecular dynamics (MD) simulations have been performed to explore changes in the VS of 1-ethyl-3-methylimidazolium hexafluorophosphate ([Emim][PF₆]) ionic liquid (IL) under an external electric field (EEF) ranging from 0 to 10 V·nm^-1 at 350 K. First, the vibrational spectra for [Emim][PF₆] IL as well as its cation and anion are separately obtained, and the peaks are strictly assigned. The results demonstrate that the VS calculated by MD simulation can well reproduce the main characteristic peaks in the experimentally measured spectrum. Then, the vibrational spectra of the IL under various EEFs from 0 to 10 V·nm^-1 are investigated, and the intrinsic origin of the changes in the vibrational bands (VBs) at 50, 183, 3196, and 3396 cm^-1 is analyzed. Our simulation results indicate that the intensities of the VBs at 50 and 183 cm^-1 are enhanced. In addition, the VB at 50 cm^-1 is redshifted by about 16 cm^-1 as the EEF is varied from 0 to 2 V·nm^-1, and the redshift wavenumber increases to 33 cm^-1 as the EEF is increased to 3 V·nm^-1 and beyond. However, the intensities of the VBs at 3196 and 3396 cm^-1 show an obvious decrease. Meanwhile, the VB at 3396 cm^-1 is redshifted by about 16 cm^-1 when the EEF increases to 3 V·nm^-1, and the redshift increases to 33 cm^-1 with an increase in the EEF beyond 4 V·nm^-1. The intensity of the VB at 50 cm^-1 increases because of the increase in the total dipole moment of each anion and cation (from 4.34 to 5.46 D), and the redshift is attributed to the decrease in the average interaction energy per ion pair (from -378.7 to -298.0 kJ·mol^-1) with increasing EEF. The intensity of the VB at 183 cm^-1 increases on account of the more consistent orientations for cations in the system with increasing EEF. The VB at 3196 cm^-1 weakens visibly because a greater number of hydrogen atoms appear around the carbon atoms on the methyl/ethyl side chains and the vibrations of the corresponding carbon-hydrogen bonds are suppressed under the action of the EEF. Furthermore, the intensity of the VB at 3396 cm^-1 decreases due to the decrease in the intermolecular ⁺C-H···F^- hydrogen bonds (HBs), while the relaxation effect that is beneficial for the formation of HBs simultaneously exists in the system under the varying EEF, thus causing a redshift of the VB at 3396 cm^-1.     

石墨烯负载的氧配位钴单原子稳定金属锂负极

Lithium (Li)-based batteries are the dominant energy source for consumer electronics, grid storage, and electrified transportation. However, the development of batteries based on graphite anodes is hindered by their limited energy density. With its ultrahigh theoretical capacity (3860 mAh∙g⁻¹), low redox potential (−3.04 V), and satisfactorily low density (0.54 g∙cm⁻³), Li metal is the most promising anode for next-generation high-energy-density batteries. Unfortunately, the limited cycling life and safety issues raised by dendrite growth, unstable solid electrolyte interphase, and "dead Li" have inhibited their practical use. An effective strategy is to develop a suitable lithiophilic matrix for regulating initial Li nucleation behavior and controlling subsequent Li growth. Herein, single-atom cobalt coordinated to oxygen sites on graphene (Co-O-G SA) is demonstrated as a Li plating substrate to efficiently regulate Li metal nucleation and growth. Owing to its dense and more uniform lithiophilic sites than single-atom cobalt coordinated to nitrogen sites on graphene (Co-N-G SA), high electronic conductivity, and high specific surface area (519 m²∙g⁻¹), Co-O-G SA could significantly reduce the local current density and promote the reversibility of Li plating and stripping. As a result, the Co-O-G SA based Li anodes exhibited a high Coulombic efficiency of 99.9% at a current density of 1 mA∙cm⁻² with a capacity of 1 mAh∙cm⁻², and excellent rate capability (high current density of 8 mA∙cm⁻²). Even at a high plating capacity of 6 mAh∙cm⁻², the Co-O-G SA electrode could stably cycle for an ultralong lifespan of 1300 h. In the symmetric battery, the Co-O-G SA based Li anode (Co-O-G SA/Li) possessed a stable voltage profile of 18 mV for 780 h at 1 mA∙cm⁻², and even at a high current density of 3 mA∙cm⁻², its overpotential maintained a small hysteresis of approximately 24 mV for > 550 h. Density functional theory calculations showed that the surface of Co-O-G SA had a stronger interaction with Li atoms with a larger binding energy, −3.1 eV, than that of Co-N-G SA (−2.5 eV), leading to a uniform distribution of metallic Li on the Co-O-G SA surface. More importantly, when matched with a sulfur cathode, the resulting Co-O-G SA/lithium sulfur full batteries exhibited a high capacity of 1002 mAh∙g⁻¹, improved kinetics with a small polarization of 191 mV, and an ultralow capacity decay rate of 0.036% per cycle for 1000 cycles at 0.5C (1C = 1675 mA∙g⁻¹) with a steady Coulombic efficiency of nearly 100%. Therefore, this work provides novel insights into the coordination environment of single atoms for the chemistry of Li metal anodes for high-energy-density batteries.     

纳米颗粒结合ZIF-67衍生的PtCo-NC催化剂用于醇类燃料电氧化

Alcohols fuel electro-oxidation is significant to the development of direct alcohols fuel cells, that are considered as a promising power source for portable electronic devices. Currently, the catalyst was restricted by the serious poisoning effect and high cost of noble metals. Developing low-cost Pt alloy with high performance and anti-CO poisoning ability was highly desired. In this work, PtCo-NC catalyst was synthesized by combining Pt nanoparticles with ZIF-67 after annealing in the tube furnace and the in situ generated N-doped carbon from ZIF-67 was functionalized to support the PtCo alloy nanoparticle. The structure and morphology were probed by X-ray diffraction, scanning electron microscope and transmission electron microscope, and the electrochemical performance was evaluated for alcohols of methanol and ethanol oxidation in the acid electrolyte. Compared with the reference sample of Pt/C, several times performance enhancement for alcohols fuel oxidation was found on PtCo-NC catalyst as well as the good catalytic stability. Specifically, the peak current density of PtCo-NC was 79.61 mA∙cm⁻² for methanol oxidation, about 2.2 times higher than that of the Pt/C electrode (36.97 mA∙cm⁻²) and 2.5 times higher than that of the commercial Pt/C electrode (31.23 mA∙cm⁻²); it was 62.69 mA∙cm^–2 for ethanol oxidation, about 1.65 times higher than that of Pt/C catalyst (37.99 mA∙cm⁻²) and commercial Pt/C electrode (37.77 mA∙cm⁻²). These catalytic performances were also much higher than some analogous catalysts developed for alcohols fuel oxidation. A much higher anti-CO poisoning ability was demonstrated by the CO stripping voltammetry experiment, in which the CO_ad oxidation peak potential for PtCo-NC was 0.46 V, ca. 110 mV negative shift compared with Pt/C catalyst at 0.57 V. A strong electronic effect was indicated by the peak position shifting to the lower binding energy direction by 0.3 eV on PtCo-NC compared with Pt/C reference catalyst. According to the d-band center theory, the electron-enriched state of Pt will decrease the interaction strength of poisoning intermediates adsorbed on its surface; Moreover, according to the bifunctional catalytic mechanism, the presence of Co can form the adsorbed oxygen-containing species (―OH) more easily than Pt at low potentials, and this oxygen-species were helpful in the oxidation of CO_ad at neighboring Pt sites. The high catalytic performance for alcohols fuel oxidation could be due to the largely improved anti-CO poisoning ability and the synergistic effect between the in situ formed PtCo nanoparticles and the N-doped carbon support.     

钴钒水滑石纳米片用于电催化尿素氧化

电解水是一种常用的制氢方法,但高能耗的阳极析氧反应(OER)阻碍了其应用。尿素氧化反应(UOR)具有较低的热力学电势,是最有前景的OER替代反应之一。过渡金属基水滑石具有独特的层状结构和层间阴离子可交换等优点,被认为是性能优异的UOR催化剂,然而目前大多数研究主要聚焦于后过渡金属元素。该研究通过一步法制备了具有前/后过渡金属的CoV-LDHs纳米片。与相同方法制备的Co(OH)₂相比,CoV-LDHs纳米片具有以下优点：1)纳米片结构有利于暴露更多的活性位点。2) V的引入增强了CoV-LDHs的亲水性,提高了其本征电催化动力学。3) Co (3d⁷4s²)和V (3d³4s²)之间的d-电子补偿效应有利于促进尿素的吸附。因此,CoV-LDHs仅需要1.52 V (vs. RHE) 就可以达到10 mA∙cm⁻²的电流密度,比Co(OH)₂低了70 mV,同时CoV-LDHs较低的塔菲尔斜率表明了其较快的反应动力学。此外,CoV-LDHs在连续反应10 h后,驱动电位几乎没有增加,表明其具有良好的稳定性。该研究结果不仅证明了前/后过渡金属之间的d-电子补偿效应可以提高UOR催化性能,还为设计高效的UOR催化剂提供了可行的途径。     

锂负极失效的全固态薄膜锂电池的直接回收再利用

作为微电子器件的理想电源，全固态薄膜锂电池(TFB)已经被广泛地研究了几十年，并开始进入商业化应用。然而，目前关于失效TFB的回收与再利用的研究几乎没有，这将会阻碍TFB的可持续发展。本工作针对因金属锂负极失效而造成电池失效的TFB，提出了一种简单的基于最常见LiCoO₂ (LCO)/LiPON/Li TFB (F-TFB)的直接回收再利用的方法。研究发现，F-TFB中的金属锂负极薄膜在循环过程会被部分氧化从而造成电池失效。我们提出利用无水乙醇溶液有效地溶解并去除F-TFB上失效的金属锂负极部分，从而快速地回收底层的LCO/LiPON薄膜。结构分析和表面分析结果表明，回收的LCO/LiPON薄膜中的LCO正极的晶体结构、LCO/LiPON的界面结构以及LiPON电解质的表面保持完好，使其再利用成为了可能。进一步地，我们在回收的LCO/LiPON薄膜上依次沉积了LiPON和Li薄膜，构建得到了电化学性能恢复的LCO/LiPON/Li TFB，并获得了与新制备的TFB相一致的比容量(0.223 mAh∙cm⁻²)、良好的倍率性能和循环寿命(500次循环后容量保持率为77.3%)。这种简单而有效的回收再利用方法有望延长固态电池的使用寿命，减少能源和资源消耗，促进固态电池的可持续发展。     

碱性聚合物电解质膜的表面锥形阵列结构提升燃料电池性能

燃料电池作为一种清洁高效的能量转换装置,被认为是构建未来社会可再生能源结构的关键一环。不同于质子交换膜燃料电池(PEMFC),碱性聚合物电解质燃料电池(APEFC)的出现使非贵金属催化剂的使用成为可能,因而受到了日益广泛的关注和研究。APEFC的关键结构是膜电极,主要由聚合物电解质膜和阴阳极(含催化层、气体扩散层)组成,膜电极是电化学反应发生的场所,其优劣直接决定着电池性能的好坏。因此,基于现有的碱性聚合物电解质及催化剂体系,如何构筑更加优化的膜电极结构,使APEFC发挥出更高的电池性能是亟待开展的研究。本文首先通过模板法在碱性聚合物电解质膜的表面构建出有序的锥形阵列,再将具有阵列结构的一侧作为阴极来构筑膜电极,同时,作为对比,制备了由无阵列结构的聚合物电解质膜构筑而成的膜电极,最后对基于两种不同膜电极的APEFC的电化学性能进行了对比研究。实验结果表明,锥形阵列结构可以将APEFC的峰值功率密度由1.04 W·cm-2显著提高到1.48 W·cm-2,这主要归因于在APEFC的阴极侧具有锥形阵列结构的聚合物电解质膜的亲水性的提升和催化剂电化学活性面积的增加。本工作为碱性聚合物电解质燃...     

Simultaneous determination of anions and cations by ion-exclusion chromatography–cation-exchange chromatography with tartaric acid/18-crown-6 as eluent

Ion-exclusion chromatography–cation-exchange chromatography was developed for the simultaneous separation of common inorganic anions and cations (Cl⁻, NO₃⁻ and SO₄²⁻; Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺) on a weakly acidic cation-exchange column by elution with weak acid. Generally, the resolution among these monovalent cations was only moderate, thereby hindering the determination of these analytes in natural-water samples. Therefore, 18-crown-6 was added to the eluent to improve the resolution. A good separation of these anions and cations on a weakly acidic cation-exchange column was achieved in 30 min by elution with 5 mM tartaric acid/6 mM 18-crown-6/methanol–water (7.5:92.5). The ion-exclusion chromatography–cation-exchange chromatography method developed here was successfully applied to the separation of major anions and cations in an environmental water sample.     

Acid-rain monitoring in East Asia with a portable-type ion-exclusion–cation-exchange chromatographic analyzer

A monitoring system consisting of a portable-type conductimetric ion-exclusion–cation-exchange chromatographic (CEC) analyzer and a meteorological satellite data analyzer has been investigated for the evaluation of the effects of acid precipitation on natural and urban environments in East Asia. The portable ion-exclusion–CEC analyzer uses a polymethacrylate-based weakly acidic cation-exchange resin column in the H⁺-form and a weak-acid eluent (tartaric acid–methanol–water) and is applied for the simultaneous determination of anions (SO₄²⁻, NO₃⁻, and Cl⁻) and cations (Na⁺, NH₄⁺, K⁺, Mg²⁺, and Ca²⁺) in precipitation transported from mainland China to central Japan, as mapped by the meteorological satellite data analyzer. Linear calibration graphs of peak area versus concentration for anions and cations were observed in the concentration range 0–1.0 mM for the anions and 0–0.5 mM for the cations. Detection limits at a signal-to-noise ratio of 3 were in the range 5.18–12.1 ppb for the anions and 6.58–16.5 ppb for the cations. The practical utility of this monitoring system is presented.     

卤化物固态电解质研究进展

全固态电池因其高能量密度和高安全性而成为具有发展前景的下一代储能技术。开发具有高室温离子电导率、优异化学/电化学稳定性、良好正/负极兼容性的固态电解质是实现全固态电池实用化的关键。卤化物固态电解质因其优异的电化学窗口、高正极稳定性、可接受的室温锂离子电导率等优势,受到了广泛的关注。本文通过对近年来卤化物电解质的相关研究进行总结,综述了该类电解质的组成、结构、离子传导路径及制备方法,并分析了金属卤化物电解质的电导率、稳定性特点,归纳了近年来该电解质在全固态电池中具有代表性的应用,并基于以上总结和分析,指出了卤化物固态电解质的研究难点及发展方向。     

三维无溶剂含能Ag-MOF的制备、热分解动力学及爆炸性能

Solvent molecules can significantly reduce the heat of detonation and stability of energetic metal-organic framework (EMOF) materials, and the development of solvent-free EMOFs has become an effective strategy to prepare high-energy density materials. In this study, a solvent-free EMOF, [Ag₂(DTPZ)]_n (1) (N% = 32.58%), was synthesized by reacting a high-energy ligand, 2, 3-di(1H-tetrazol-5-yl)pyrazine (H₂DTPZ), with silver ions under hydrothermal conditions, and it was structurally characterized by elemental analysis, infrared spectroscopy, X-ray diffraction, and thermal analysis. In 1, the DTPZ²⁻ ligands that adopted a highly torsional configuration bridged the Ag⁺ ions in an octadentate coordination mode to form a three-dimensional framework (ρ = 2.812 g∙cm⁻³). The large steric effect and strong coordination ability of DTPZ²⁻ effectively prevented the solvent molecules from binding with the metal centers or occupying the voids of 1. Moreover, the strong π-π stacking interactions [centroid-centroid distance = 0.34461(1) nm] between the tetrazole rings in different DTPZ²⁻ ligands provided a high thermal stability to the framework (T_e = 619.1 K, T_p = 658.7 K). Thermal analysis showed that a one-step rapid weight loss with intense heat release primarily occurred during the decomposition of 1, suggesting potential energetic characteristics. Non-isothermal thermokinetic analyses (based on the Kissinger and Ozawa-Doyle methods) were performed using differential scanning calorimetry to obtain the thermoanalysis kinetic parameters of the thermodecomposition of 1 (E_a = 272.1 kJ·mol⁻¹, E_o = 268.9 kJ·mol⁻¹; lgA =19.67 s⁻¹). The related thermodynamic parameters [enthalpy of activation (ΔH^≠ = 266.9 kJ·mol⁻¹), entropy of activation (ΔS^≠ = 125.4 J·mol⁻¹·K⁻¹), free energy of activation (ΔG^≠ = 188.3 kJ·mol⁻¹)], critical temperature of thermal explosion (T_b = 607.1 K), and self-accelerating decomposition temperature (T_SADT = 595.8 K) of the decomposition reaction were also calculated based on the decomposition peak temperature and extrapolated onset temperature when the heating rate approached zero. The results revealed that 1 featured good thermal safety, and its decomposition was a non-spontaneous entropy-driven process. The standard molar enthalpy for the formation of 1 was calculated to be (2165.99 ± 0.81) kJ·mol⁻¹ based on its constant volume combustion energy determined using a precise rotating oxygen bomb calorimeter. Detonation and safety performance tests revealed that 1 was insensitive to impact and friction, and its heat of detonation (10.15 kJ·g⁻¹) was higher than that of common ammonium nitrate explosives, such as octogen (HMX), hexogene (RDX), and 2, 4, 6-trinitrotoluene (TNT), indicating that 1 is a promising high-energy and insensitive material.