Bi2WO6量子点(QDs)修饰Bi2MoO6-xF2x异质结的构筑及其催化活性增强机理

采用简单沉积-沉淀法合成了Bi₂WO₆@Bi₂MoO_6-xF_2x（BWO/BMO6-xF2x）异质结,借助XRD、XPS、TEM、SEM、EDS、UV-Vis-DRS、PC和EIS等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征,并以模型污染物罗丹明B（RhB）的光催化降解作为探针反应来评价Bi₂WO₆@Bi₂MoO_6-xF_2x异质结的光催化活性增强机制。形貌分析表明,所得Bi₂MoO₆微球由大量厚度为20~50 nm的纳米片组成;FE-SEM和HR-TEM分析表明,尺寸约为10 nm的Bi₂WO₆量子点均匀沉积在Bi₂MoO_6-xF_2x微球表面,形成新颖的Bi₂WO₆@Bi₂MoO_6-xF_2x异质结;与纯Bi₂MoO₆或者Bi₂WO₆相比,1∶1Bi₂WO₆@Bi₂MoO_6-xF_2x异质结表现出更好的光催化活性和光电流性质,其对RhB光催化降解的表观速率常数分别为纯BMO和BWO的6.4和11.6倍。PC和EIS图谱分析表明,Bi₂WO₆量子点表面沉积显著提高Bi₂MoO_6-xF_2x光生电子/空穴的分离效率和迁移速率;活性物种捕获实验证明了·O₂^-和h⁺是主要的活性物种。根据实验结果,探讨了F^-掺杂和Bi₂WO₆量子点之间的协同效应对Bi₂MoO₆的光催化活性的影响机制。     

溴代烷烃与活性氮的反应发光研究

在流动余辉装置上, 利用N₂空心阴极放电制备活性氮, 研究了活性氮与溴代烷烃(CHBr₃、CH₂Br₂、C₂H₅Br、C₄H₉Br) 反应的化学发光.上述所有反应中, 在550～750 nm波段均观察到了较强的NBr (b¹Σ+→X³Σ^-)跃迁发射谱. 同时在活性氮与CHBr₃和CH₂Br₂的反应中, 在流动管下游还观察到了CN (A²π, B²π→X²Σ⁺)的发射谱. 验证性的实验表明, 激发态NBr (b¹Σ⁺)是由二步过程形成: N(⁴S)与溴代烷烃反应生成NBr (X³Σ^-), 再通过N₂ (A ³Σ_u⁺)分子能量转移到激发态NBr (b¹Σ⁺); 而激发态的CN是通过N(⁴S) + CBr→CN(A, B) + Br过程形成的.     

三元体系YCl3-CdCl2-H2O和四元体系YCl3-CdCl2-HCl(～8.8%)-H2O (25 ℃)的相平衡及其固相新化合物的研究

The equilibrium solubilities of the ternary system YCl₃-CdCl₂-H₂O, the quaternary system YCl₃-CdCl₂-HCl(～8.8%)-H₂O were determined at 25 ℃ and the phase diagrams were constructed. The results show that the ternary system was complicated with six equilibrim solid phases CdCl₂·2.5H₂O, CdCl₂·H₂O, 8CdCl₂·YCl₃·15H₂O (8∶1 type), 4CdCl₂·YCl₃·13H₂O(4∶1 type), 5CdCl₂·2YCl₃·26H₂O (5∶2 type) and YCl₃·6H₂O. The quaternary system was also complicated with four equilibrim solid phase CdCl₂·H₂O, 4CdCl₂·YCl₃·13H₂O (4∶1 type), 5CdCl₂·2YCl₃·26H₂O(5∶2 type) and YCl₃·6H₂O. Among the three new compounds 8CdCl₂·YCl₃·15H₂O, 4CdCl₂·YCl₃·13H₂O and 5CdCl₂·2YCl₃·26H₂O, 8CdCl₂·YCl₃·15H₂O was a kind of metastable compound only in ternary system, and it was changed into 4CdCl₂·YCl₃·13H₂O with time. Both 4∶1 type and 5∶2 type existed in ternary and quaternary system, but they were also congruently soluble compounds in quaternary system. They have been prepared from the system and have been characterized by XRD, TC-DTG and DSC.     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

不同温度下VUV光激发的Pr3+离子的发光性质

The luminescent properties of Pr³⁺-doped LaB₃O₆, SrAl₁₂O₁₉, SrB₄O₇ and NaYF₄ in the vaccum ultraviol-et (VUV) range at different temperatures were investigated under the excitation of high-energetic synchrotron radiation. For Pr³⁺ ions in LaB₃O₆, SrAl₁₂O₁₉ and SrB₄O₇, only the parity-forbidden ¹S₀→4f² transitions were observ-ed in the emission spectra at relatively low temperature; but the parity-allowed 4f5d→4f² transitions appeared simultaneously when the temperature was high enough. And the intensity of broad 4f5d→4f² emission increased relative to the intensity of ¹S₀→4f² emissions with increasing temperature. Then the thermal equilibrium model of energy levels was employed to the lowest 4f5d state and ¹S₀ state of Pr³⁺ in the three hosts. The calculated curves were in good agreement with the experimental values, indicating the occurrence of the thermal excitation from ¹S₀ state to 4f5d states at high temperatures when the lowest 4f5d state lies higher than ¹S₀ state and the photon energy is high enough.     

纳米Mn-Zn铁氧体的制备和研究

Nanosize manganese zinc ferrites were fabricated by hydrothermal precipitation route using Fe₂(SO₄)₃, ZnSO₄·7H₂O, MnSO₄·H₂O as material, then some calcinated at 500 ℃ and studied by XRD, TEM, IR and VSM. The results showed that the products were spinel crystal structure and uniformly sized nanoparticles (15～25 nm) with little aggregation. The analysis of IR showed that the superficial water can be eliminated, but that was embedded in crystal lattice can not be removed by calcinating. The effect Zn content x on the lattice (a) of nanosize Mn_1-xZn_xFe₂O₄ was also discussed. The lattice of nanosize Mn_1-xZn_xFe₂O₄ decreases with x increasing; and its value deviated the standard lattice (a₀) of normal size manganese zinc ferrites. A lot of water was absorbed during the hydrothermal process owing to the large surface of nanosize particles. The change of magnetic properties of Mn_xZn_1-xFe₂O₄ with x increasing was studied: nanosize Mn_xZn_1-xFe₂O₄ particles synthesized by us exhibited peculiar magnetic properties curve with Zn content (x) increasing, Superparamagnetic behaviors of the synthesized ZnFe₂O₄ samples were confirmed by magnetic characterization, which can be explained by the difference between the distribution of the metal ions (Mn²⁺, Zn²⁺ and Fe³⁺) among the tetrahedral (A) and the octahedral (B) sites of nanosize ferrite and that of bulk ferrite.     

新半金属Fe2LaO4磁电性能的第一性原理计算

利用基于密度泛函理论的第一性原理赝势法设计并优化了含稀土元素的新半金属Fe₂LaO₄。详细计算了其电荷分布,分子磁矩等磁电性能，并结合配位场理论分析了其电子结构。结果表明，Fe₂LaO₄是一种含稀土元素的铁磁性的新ⅡB型半金属；它的稳定相晶格常数约为0.623 nm，分子磁矩约为1.0μ_B；Fe₂LaO₄属软铁磁性半金属；La较多的外层电子增强了Fe₂LaO₄内部的库仑斥力,导致了配合物ML₄和ML₆均受强场作用,从而使Fe₂LaO₄具有软铁磁性；考虑自旋分布后ML₄和ML₆的电子结构分别为a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓e_g²↑e_g²↓t_2g³↑t_2g³↓和a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓t_2g³↑t_2g³↓e_g²↑e_g²↓e_g^*1↑,这些电子属于分子轨道。     

空气中合成固溶体荧光粉Ba2(Zn, Mg)Si2O7:Ce3+,Eu2+,Eu3+及其发光特性

采用高温固相法在空气中合成了Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu,yCe³⁺系列荧光粉。分别采用X-射线衍射和荧光光谱对所合成荧光粉的物相和发光性质进行了表征。在紫外光330~360 nm激发下,固溶体荧光粉Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu的发射光谱在350~725 nm范围内呈现多谱峰发射,360和500 nm处有强的宽带发射属于Eu²⁺离子的4f⁶5d¹-4f⁷跃迁,590~725 nm红光区窄带谱源于Eu³⁺的⁵D₀-⁷F_J (J=1,2,3,4)跃迁,这表明,在空气气氛中,部分Eu³⁺在Ba_1.97-yZn_1-xMg_xSi₂O₇基质中被还原成了Eu²⁺;当x=0.1时,荧光粉Ba_1.97Zn_0.9Mg_0.1Si₂O₇:0.03Eu的绿色发光最强,表明Eu³⁺被还原成Eu²⁺离子的程度最大。当共掺入Ce³⁺离子后,形成Ba_1.97-yZn_0.9Mg_0.1Si₂O₇:0.03Eu,yCe³⁺荧光粉体系,其发光随着Ce³⁺离子浓度的增大由蓝绿区经白光区到达橙红区;发现名义组成为Ba_1.96Zn_0.9Mg_0.1Si₂O₇:0.01Ce³⁺,0.03Eu的荧光粉的色坐标为(0.323,0.311),接近理想白光,是一种有潜在应用价值的白光荧光粉。讨论了稀土离子在Ba₂Zn_0.9Mg_0.1Si₂O₇基质中的能量传递与发光机理。     

CeCl3-CdCl2-H2O和CeCl3-CdCl2-HCl-H2O的相平衡

测定了三元系CeCl₃-CdCl₂-H₂O (25 ℃)和四元系CeCl₃-CdCl₂-HCl(～8.4％)-H₂O(25 ℃) 的相平衡溶度数据,绘制了相应的溶度图.该三元系是由5个固相区CdCl₂&;#8226;2.5H₂O(原始盐)、CdCl₂&;#8226;H₂O(原始盐)、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O、4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O、CeCl₃&;#8226;7H₂O(原始盐)组成的复杂体系.该四元系是由5个固相区CdCl₂&;#8226;H₂O(原始盐)、9CdCl₂&;#8226;CeCl₃&;#8226;19H₂O、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O、4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O、CeCl₃&;#8226;7H₂O(原始盐)组成的复杂体系.其中6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O在该三元系是介稳化合物.9CdCl₂&;#8226;CeCl₃&;#8226;19H₂O 、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O和4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O用X射线粉末衍射及TG-DTG和DSC等方法进行了研究,并对X射线粉末衍射进行了指标化.     

掺杂和取代对红色荧光材料SrAl12O19:Mn4+发光性能的影响

SrAl₁₂O₁₉：Mn⁴⁺是一种用于高显色性白光发光二极管的候选红色荧光材料。本论文研究了Mg²⁺、Zn²⁺和Ge⁴⁺离子的掺杂效应以及Ga³⁺、Ca²⁺和Ba²⁺离子的取代效应对SrAl₁₂O₁₉：Mn⁴⁺荧光材料性能的影响。样品通过高温固相反应制备,焙烧温度在1 250~1 500 ℃之间。利用X射线衍射技术表征了材料的相纯度,用荧光激发光谱和发射光谱表征了材料的荧光性能。研究结果指出,与未进行Mg²⁺或Zn²⁺掺杂的样品相比,Mg²⁺或Zn²⁺离子对Al³⁺格位的掺杂可以使材料的发光强度提高~60%,其原因被认为是掺杂促进了激活剂Mn⁴⁺离子进入晶格,其过程可以表示为：MO+MnO₂⇔M_Al^''+M_Al^·+3O_O^×（M=Mg,Zn）,电子顺磁共振谱支持这一结果。Ge⁴⁺离子的掺杂使材料的发光性能明显下降。Ga³⁺离子可以取代Al³⁺离子形成全范围的固溶体,其中少量Ga³⁺离子的掺杂可以使材料的荧光发射强度提高~13%,而掺杂量进一步提高使材料的荧光性能下降。Ca²⁺和Ba²⁺对Sr²⁺的取代仅形成有限范围的固溶体。Ca²⁺的取代使材料的发光性能提高;而 Ba²⁺的取代使材料的发光强度下降。     

Carbonaceous species of TSP in urban and rural sites around coal-fired power stations in northwestern Greece

Total suspended particles from urban and rural locations around an industrial complex with four coal-fired power stations were collected for a period of 6 months (January-June 2001). Mass concentrations of TSP and carbonaceous species (TC, EC, OC and BC) were determined for seven sampling sites of the studied area. The contribution of TC mass to the total particle mass was similar for all sites with an average value of 12.36±1.27%. The fraction of elemental carbon (EC) was estimated between 32 and 46% of the total carbon (TC). The relationship between organic and elemental carbon showed the primary origin of organic carbon (direct emissions). The OC/BC ratio values were also considered in order to get information about the enrichment of aerosols in organic carbon. Four conditional categories out of the sampling site ‘collection were additionally extracted (“urban”, “rural”, “far” and “close” location to the power stations) and considered with respect to the values of the ratios OC/BC and OC/EC and the multiple correlation coefficients R² for the concentrations of OC, BC and EC. It has been found that in some cases the correlation coefficients rather than the ratios could inform on the type of site.     

THEORETICAL COMPARISON OF THE BONDING OF CHALCOCARBONYL LIGANDS

Abstract

Fenske-Hall molecular orbital calculations on the complexes CpFe(CO)₂(CX)⁺ (X = O, S, Se, and Te) have been used to quantify the nature of bonding between the CX ligands and the metal atom. In addition, conclusions have been reached about the reactivity of the complexes under both nucleophilic and electrophilic attack. The previously established trend of increasing metal—ligand bond strength as X changes from O to S to Se is demonstrated by our molecular orbital calculations, and found to extend to Te. The mechanism for nucleophilic attack, variously explained in the past by either charge control or orbital control, is quantitatively ascribed to orbital control only. The nature of electrophilic attack on these complexes is also found to begin with orbital control.     

多孔炭材料的研究进展及前景

近年来多孔炭材料在国内外的研究和开发应用都十分活跃。本文从制备原料的扩展, 形态特征的增多, 纳米空间的控制, 功能特性的改进, 微细组织的察, 应用途径的开拓等不同方面综述了多孔炭材料的研究和应用开发的新进展。     

Spiro-Carbon: A Metallic Carbon Allotrope Predicted from First Principles Calculations

A structurally stable microporous metallic carbon allotrope, poly(spiro[2.2]penta-1,4-diyne) or, for short, spiro-carbon, with I4₁/amd (D_4h) symmetry is predicted by first-principles calculations using density functional theory (DFT). The calculations of electronic, vibrational, and structural properties show that spiro-carbon has lower relative energy than other elusive carbon allotropes such as T-Carbon and 1-diamondyne (Y-Carbon). Its structure can be pictured as a set of trans-cisoid-polyacetylene chains tangled and interconnected together by sp³ carbon atoms. Calculations reveal a metallic electronic structure arising from an “intrinsic doping” of trans-cisoid-polyacetylene chains with sp³ carbon atoms. Possible synthetic routes and various simulated spectra (XRD, NMR, and IR absorption) are provided in order to guide future efforts to synthesize this novel material.     

新型碳材料作为直接醇类燃料电池催化剂载体的评述

 电催化反应过程涉及固、液、气传输以及电子和质子传导, 为确保反应的顺利进行和提高催化剂中贵金属的利用率及延长催化剂的寿命, 理想的电催化剂载体必须同时具备高比表面积、导电性好、合适的孔结构、耐腐蚀以及合适的表面基团等. 为此, 碳载体的改性工作受到关注, 常用的方法是通过酸、碱、氧化和高分子等手段改变载体的结构和表面性质, 以期接近理想电催化剂载体的要求; 同时在开发新型碳载体方面做了更大量的工作. 本文简要评述了商品炭载体如碳黑 Vulcan XC-72R 以及其它的乙炔黑、黑珍珠-2000、Printex XE-2 和 Ketjen Black EC 等碳材料在直接醇燃料电池中的应用, 但对纳米碳纤维、碳纳米管、有序多孔碳、中间相碳小球、碳纳米角、碳纳米卷和碳气凝胶等新型碳载体则进行了较全面的评述. 与商品碳载体相比, 新型碳载体在一定程度上都表现出比 XC-72R 更优的性能, 这主要是因为新型碳材料具有特殊的结构、更高的结晶性能 (导电性) 和更好的传质能力.     

Gasification of hydrolysis lignin with CO2 in the presence of Fe and Co compounds

The effect of the nature of the metal (Fe and Co) deposited on the surface of hydrolysis lignin, as well as the metal content (1, 3, 5 and 7 wt%), on the process of dry catalytic lignin reforming has been studied. The use of the catalyst led to a twofold increase in the conversion of carbon dioxide at temperatures of 500–800 °C, while both metals showed similar activity. The maximum specific catalytic effect is achieved when supporting 7 wt% of active metals.     

Applying diamond like carbon layer on carbon/carbon composites and its effect on the deposition of hydroxyapatite coating

The biomedical application of carbon/carbon (C/C) composites is limited by lacking bioactivity and releasing carbon debris. Hydroxyapatite (HA) coating has been used to improve the bioactivity of C/C composites, but it cannot reduce the release of carbon debris effectively because of poor wear resistance property. In this work, a wear‐resistant layer of diamond like carbon (DLC) is applied on C/C composites, followed by an ultrasound‐assisted electrochemical deposition to prepare HA coatings. The microstructure, morphology and chemical composition of the DLC layer and the HA coating are characterised by scanning electron microscopy, X‐ray diffraction, energy dispersive spectroscopy (EDS), X‐ray photoelectron spectroscopy, Fourier transformed infrared spectroscopy and Raman spectrum. The bonding strength between the HA coating and the DLC layer modified C/C composites is examined by a tensile test. The results show that the DLC layer has a spherical morphology and provides a uniform surface for the deposition of the HA coating. The HA coating shows flaky morphology with a compact structure. The tensile strength of the HA coating on the DLC layer modified C/C composites is 6.24 ± 0.40 MPa, which is significantly higher than that of HA coating on unmodified C/C composites(3.04 ± 0.20 MPa). Copyright © 2013 John Wiley & Sons, Ltd.     

炭材料对铀的吸附

铀既是核燃料的主要成分又是乏燃料后处理的关键核素。将铀从乏燃料后处理流程中的高放射性料液或者其他含铀废水中分离出来既可以将此宝贵的核燃料回收使用,又有利于降低乏燃料处理后期的处置费用,以及减少铀对环境的污染。而从海水、盐湖水、尾矿废水等贫铀水体中提取铀则可能是解决将来铀资源匮乏的主要方法。炭质材料具有较大的比表面积、较高的孔隙率,耐高温,抗辐射,对各种酸碱环境有很高稳定性,而且本身无毒,环境友好,有望作为吸附剂或固相萃取材料用于从水体中吸附分离铀。本文介绍了活性炭、介孔炭、碳纳米管等材料对铀的吸附研究进展。表面功能化可以提高炭材料对铀酰离子的吸附容量与选择性,对炭材料功能化的方法主要有表面氧化、浸渍、负载和接枝等手段。由于化学稳定性高,采用化学方法在炭材料表面接枝功能分子是具有应用前景的研究方向。采用碳纤维作电极,电吸附铀的方法可以大量地从水溶液中将铀吸附到电极表面,再通过电脱附回收铀,具有工业化应用前景。     

多色荧光碳点的制备新进展

碳点(碳量子点)是在紫外-可见光吸收区域具有有效吸收的、可多色发光的新型碳纳米材料,在生物医学、环境能源和催化领域有着重要的研究应用前景。但是,在过去的10年中,无论是自上而下还是自下而上的方法,所制备碳点的发光大部分集中在蓝光-橙光范围。最近,随着制备方法的改进,有多种方法制备出了红光或近红外发光的碳点。本文简述了近3年来各类代表性的制备碳点的方法,并主要介绍了红光或近红外发光碳点的制备新进展。     

诺贝尔奖宠儿——碳元素的前世今生

碳元素历史悠久,与现代人类社会联系紧密,对人类未来意义重大,多次斩获诺贝尔奖。在揭开碳元素的发现史之后,介绍了活性炭、碳纤维、玻璃碳等无定形碳以及热解炭等过渡碳的重要作用。此外,晶形碳的经典同素异形体--C60富勒烯、碳纳米管、石墨烯的独特结构造就了其在纳米材料领域的非凡用途;新型同素异形体的合成、发现与应用更是碳元素研究领域的热点。