Chemometric approaches in calibration experiments of trilinolenoylglycerol by liquid chromatography ion-trap mass spectrometry

The article presents a comprehensive account of the application of chemometric approaches to determine the factors that influence the tri-alpha-linolenoylglycerol (TALG) ammoniated adduct signal m/z 890.6 in an ion-trap mass spectrometer coupled to a liquid chromatograph and the estimation of different sources of errors involved in TALG calibration experiments. It was found that by using experimental design, the influence of the nebulizer pressure on the analytical signal is less pronounced than the influence of the drying gas flow and the chromatographic flow rate. The results revealed that without using tandem mass or atmospheric pressure chemical ionization, it is possible to fragment the TALG backbone and obtain the free alpha-linolenic acid by varying the drying gas flow and using an electrospray interface. The error decomposition approach revealed that the preparation error was 26 times higher than the instrumental error.     

On-line fermentation gas analysis: Error analysis and application of mass spectrometry

On-line fermentation gas analysis is of general interest because it permits the determination of metabolic rates in almost any biological process using living organisms. The consumption and production of gases (O₂, CO₂, CH₄, etc.) and volatile compounds may be determined without causing any risk of infection. Elemental balancing permits the determination of other metabolic rates if the stoichiometry is known. This was studied with the production of poly-β-hydroxybutyrate (PHB) by Alcaligenes latus. Estimations were based on the measurement of gas partial pressure and flow-rates, pH and alkali consumption rate. Experiments with a small quadrupole mass spectrometer showed unacceptable error propagation. Therefore, dynamic error propagation for all rates was studied using simulation. It was found that, for example, a 1% relative offset-calibration error for oxygen can result in an error in PHB estimation of > 50%. It is suggested that this culture is used in combination with elemental balancing for thorough tests of the accuracy of on-line gas analysis equipment. An on-line process gas analyser based on a quadrupole mass spectrometer (Balzers PGM 407) gave the following precision values (abs. vol.?%) during cultivation of Bacillus subtilis: nitrogen (m/z 14), 0.024; oxygen (m/z 32), 0.020; argon (m/z 40), 0.0011; and carbon dioxide (m/z 44), 0.0034. These values, combined with automatic recalibration, would be sufficient for reasonable estimation of PHB, biomass and substrates.     

Optimization of the Ion Source-Mass Spectrometry Parameters in Non-Steroidal Anti-Inflammatory and Analgesic Pharmaceuticals Analysis by a Design of Experiments Approach

The flow rates of drying and nebulizing gas, heat block and desolvation line temperatures and interface voltage are potential electrospray ionization parameters as they may enhance sensitivity of the mass spectrometer. The conditions that give higher sensitivity of 13 pharmaceuticals were explored. First, Plackett-Burman design was implemented to screen significant factors, and it was concluded that interface voltage and nebulizing gas flow were the only factors that influence the intensity signal for all pharmaceuticals. This fractionated factorial design was projected to set a full 2² factorial design with center points. The lack-of-fit test proved to be significant. Then, a central composite face-centered design was conducted. Finally, a stepwise multiple linear regression and subsequently an optimization problem solving were carried out. Two main drug clusters were found concerning the signal intensities of all runs of the augmented factorial design. p-Aminophenol, salicylic acid, and nimesulide constitute one cluster as a result of showing much higher sensitivity than the remaining drugs. The other cluster is more homogeneous with some sub-clusters comprising one pharmaceutical and its respective metabolite. It was observed that instrumental signal increased when both significant factors increased with maximum signal occurring when both codified factors are set at level +1. It was also found that, for most of the pharmaceuticals, interface voltage influences the intensity of the instrument more than the nebulizing gas flowrate. The only exceptions refer to nimesulide where the relative importance of the factors is reversed and still salicylic acid where both factors equally influence the instrumental signal.

Open image in new window

Graphical Abstract ?

     

Matrix-assisted laser desorption/ionization imaging mass spectrometry revealed traces of dental problem associated with dental structure

Periodontal disease is a serious dental problem because it does not heal naturally and leads to tooth loss. In periodontal disease, inflammation at periodontal tissue is thought as predominant, and its effect against tooth itself remains unclear. In this study, we applied matrix-assisted laser desorption/ionization imaging mass spectrometry (IMS) to teeth for the first time. By comparing anatomical structure of tooth affected with periodontal disease with normal ones, we analyzed traces of the disease on tooth. We found signals characteristic of enamel, dentin, and dental pulp, respectively, in mass spectra obtained from normal teeth. Ion images reconstructed using these signals showed anatomical structures of the tooth clearly. Next, we performed IMS upon teeth of periodontal disease. Overall characteristic of the mass spectrum appeared similar to normal ones. However, ion images reconstructed using signals from the tooth of periodontal disease revealed loss of periodontal ligament visualized together with dental pulp in normal teeth. Moreover, ion image clearly depicted an accumulation of signal at m/z 496.3 at root surface. Such an accumulation that cannot be examined only from mass spectrum was revealed by utilization of IMS. Recent studies about inflammation revealed that the signal at m/z 496.3 reflects lyso-phosphatidylcholine (LPC). Infiltration of the signal is statistically significant, and its intensity profile exhibited the influence has reached deeply into the tooth. This suggests that influence of periodontal disease is not only inflammation of periodontal tissue but also infiltration of LPC to root surface, and therefore, anti-inflammatory treatment is required besides conventional treatments.     

Non-invasive imaging of shallow bubble columns using electrical capacitance tomography

This paper deals with application of non-invasive electrical capacitance tomography to study the hydrodynamics of shallow bed bubble columns. Two bubble columns with different height to diameter ratio were used. Air–kerosene system that represents dielectric two-phase mixture was investigated. The ECT provided good measurement of the gas holdup at different gas velocities compared to the classical pressure measurements. The ECT was able to provide the gas hold up and the bubble velocities distribution across the column diameter at different gas velocities. The study revealed that spatial gas holdup and bubble velocity distributions are sharp with parabolic shape in the small bubble column (H_D/D_C = 5). However, in the large bubble column (H_D/D_C = 4) the gas holdup and bubble velocity profiles were flatter indicating improvement in the mixing homogeneity and leading to well-mixed reactor. 3D graphical visualization of the flow regimes and transition points were also examined using the ECT. In the small bubble column flow regimes were heterogeneous to slugs flow especially at high flow rate, resulted in downward flow near the walls and imperfect mixing.     

A systematic study on the influence of carbon on the behavior of hard-to-ionize elements in inductively coupled plasma–mass spectrometry

A systematic study on the influence of carbon on the signal of a large number of hard-to-ionize elements (i.e. B, Be, P, S, Zn, As, Se, Pd, Cd, Sb, I, Te, Os, Ir, Pt, Au, and Hg) in inductively coupled plasma–mass spectrometry has been carried out. To this end, carbon matrix effects have been evaluated considering different plasma parameters (i.e. nebulizer gas flow rate, r.f. power and sample uptake rate), sample introduction systems, concentration and type of carbon matrix (i.e. glycerol, citric acid, potassium citrate and ammonium carbonate) and type of mass spectrometer (i.e. quadrupole filter vs. double-focusing sector field mass spectrometer). Experimental results show that P, As, Se, Sb, Te, I, Au and Hg sensitivities are always higher for carbon-containing solutions than those obtained without carbon. The other hard-to-ionize elements (Be, B, S, Zn, Pd, Cd, Os, Ir and Pt) show no matrix effect, signal enhancement or signal suppression depending on the experimental conditions selected. The matrix effects caused by the presence of carbon are explained by changes in the plasma characteristics and the corresponding changes in ion distribution in the plasma (as reflected in the signal behavior plot, i.e. the signal intensity as a function of the nebulizer gas flow rate). However, the matrix effects for P, As, Se, Sb, Te, I, Au and Hg are also related to an increase in analyte ion population caused as a result of charge transfer reactions involving carbon-containing charged species in the plasma. The predominant specie is C⁺, but other species such as CO⁺, CO₂⁺, C₂⁺ and ArC⁺ could also play a role. Theoretical data suggest that B, Be, S, Pd, Cd, Os, Ir and Pt could also be involved in carbon based charge transfer reactions, but no experimental evidence substantiating this view has been found.     

Non-spectral interferences encountered with a commercially available high resolution ICP-mass spectrometer

Results of a systematic study concerning non-spectral interferences observed with a commercially available high resolution ICP-mass spectrometer are reported and compared to observations made with a quadrupole-based instrument. In general, matrix effects were observed to be to a large extent comparable for both instruments used. In all cases, the matrix-induced signal suppression or enhancement was seen to depend in a regular way on the mass number of the nuclides monitored. In most cases, the ionization potential of the nuclides has little or no influence on the extent of suppression or enhancement. For As, Se and Te, the introduction of 2.5% ethanol, 0.5 mol/l H₂SO₄, or to a lesser extent 0.5 mol/l H₃PO₄, leads to an exceptional increase in the signal intensity for both instruments. Registration of signal behaviour plots (signal intensity as a function of the nebulizer gas flow rate) in different matrices revealed that both the height of the plot and the optimum nebulizer gas flow rate are a function of the matrix composition. Finally, no indication was found that the acceleration of the extracted ions over 8000 V with the high resolution instrument would lead to an alleviation of space charge effects when compared to a quadrupole-based ICP-mass spectrometer.     

Study on Tissue Distribution of A Variety of Endogenous Metabolites By Air Flow Assisted Ionization-Ultra High Resolution Mass Spectrometry Imaging

As a promising new molecular imaging technique, mass spectrometry imaging (MSI) has attracted more and more attention in the field of biomedicine. A method of air flow assisted ionization-ultra high resolution mass spectrometry-based mass spectrometric imaging (AFAI-MSI) was developed to profile endogenous metabolites in rat kidney tissue in this study. Rat kidneys were collected and cut into frozen tissue sections, and then were analyzed on an AFAI-MSI system operated in positive ion mode using acetonitrile- isopropanol-water (4:4:2, V/V, 5 μL min^?1) as spray solvent, nitrogen gas as spray gas (0.6 MPa) and air as assisting gas (45 L min^?1). The mass range and resolution were set to be 70–1000 Da and 70000, respectively. As a result, a total of 38 metabolites, ranging from 10³ to 10⁷ in signal strength and belonging to different metabolite types, including organic amines, sugars, vitamins, peptides, neurotransmitters, organic acids, phospholipids, sphingolipids, glycerides, and cholesterol esters, were identified and imaged to characterize their tissue-specific distribution in kidney tissues. Some metabolites, such as choline, acetycholine, betaine, phosphocholine, and glycerolphosphocholin were found to have distinct distribution along the cortex-medulla axis, which may be involved in the formation of osmotic pressure gradient in the kidney. The proposed ultra high resolution mass spectrometry based AFAI-MSI method can work without sample pretreatment, showing high sensitivity and wide metabolite coverage, and is expected to provide a new analytical approach in the research of in situ characterization and metabolic regulation mechanism of endogenous metabolites in kidney.     

Drying Effects on Chemical Composition and Antioxidant Activity of Lippia thymoides Essential Oil,a Natural Source of Thymol

Leaves of Lippia thymoides (Verbenaceae) were dried in an oven at 40, 50 and 60 °C and the kinetic of drying and the influence of the drying process on the chemical composition, yield, and DPPH radical scavenging activity of the obtained essential oils were evaluated. The composition of the essential oils was determined with gas chromatography-mass spectrometry and gas chromatography-flame ionization detection analyses. The influence of drying on the chemical composition of the essential oils of L. thymoides was evaluated by multivariate analysis, and their antioxidant activity was investigated via the 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay. The Midilli model was the most appropriate to describe the behavior of drying kinetic data of L. thymoides leaves. Thymol was the major compound for all analyzed conditions; the maximum content was obtained from fresh leaves (62.78 ± 0.63%). The essential oils showed DPPH radical scavenging activity with an average of 73.10 ± 12.08%, and the fresh leaves showed higher inhibition (89.97 ± 0.31%). This is the first study to evaluate the influence of drying on the chemical composition and antioxidant activity of L. thymoides essential oils rich in thymol.     

Error of sample preparation in pressing emitters for X-ray fluorescence analysis

When determining element concentrations in geological samples by X-ray fluorescence spectrometry using emitters obtained by pressing tablets from powder samples, we revealed the effect of a significant difference in line intensities of characteristic long-wavelength emission (ΔI _i) from opposite sides of the emitter. The effects of compacting pressure, mass of emitter, and its surface area on ΔI _i were investigated. It was shown that the account of this effect can reduce the error of sample preparation in using compacting pressures lower than 20 t.     

An improved method for the simultaneous analysis of phenolic and steroidal estrogens in water and sediment

This paper describes an improved method for the extraction and analysis of seven endocrine disrupting chemicals with wide-ranging polarities from water and sediments using gas chromatography-tandem mass spectrometry (GC-MS/MS). The analytes were 4-tert-octylphenol, 4-nonylphenol, bisphenol A, estrone, 17β-estradiol, 17α-ethynylestradiol and 16α-hydroxyestrone. The optimised GC-MS/MS method produces increased selectivity and sensitivity compared to GC-MS, with limit of detection ranging from 0.01 to 0.49 ng L⁻¹ in water and from 0.05 to 0.14 ng g⁻¹ in sediment. Extraction from aqueous samples was performed by solid-phase extraction (SPE) and from sediment samples by microwave-assisted extraction (MAE). The improved method for the clean-up of sediment extracts carried out by SPE enhanced EDC recovery (86-102%) while reducing matrix interference and sample drying time. Derivatisation of final sample extracts was achieved using N,O-bis(trimethylsilyl)trifluoroacetamide and pyridine, and their stability was enhanced by reconstituting the derivatised extracts with hexane. The method was validated by spiking experiments which showed good recovery and reproducibility. The method was applied to samples taken from the Medway estuary in Kent, UK, where non-conservative behaviour of EDCs was demonstrated.     

Comparison of the internal energy deposition of direct analysis in real time and electrospray ionization time-of-flight mass spectrometry

The internal energy (E_int) distributions of a series of p-substituted benzylpyridinium ions generated by both direct analysis in real time (DART) and electrospray ionization (ESI) were compared using the “survival yield” method. DART mean E_int values at gas flow rates of 2, 4, and 6 L min⁻¹, and at set temperatures of 175, 250, and 325 °C were in the 1.92–2.21 eV range. ESI mean E_int at identical temperatures in aqueous and 50% methanol solutions ranged between 1.71 and 1.96 eV, and 1.53 and 1.63 eV, respectively. Although the results indicated that ESI is a “softer” ionization technique than DART, there was overlap between the two techniques for the particular time-of-flight mass spectrometer used. As a whole, there was an increase in E_int with increasing reactive and drying gas temperatures for DART and ESI, respectively, indicating thermal ion activation. Three dimensional computational fluid dynamic simulations in combination with direct temperature measurements within the DART ionization region revealed complex inversely coupled fluid-thermal phenomena affecting ion E_int values during atmospheric transport. Primarily, that DART gas temperature in the ionization region was appreciably less than the set gas temperature of DART due to the set gas flow rates. There was no evidence of E_int deposition pathways from metastable-stimulated desorption, but fragmentation induced by high-energy helium metastables was observed at the highest gas flow rates and temperatures.     

In situ sulfur isotopes (δS and δS) analyses in sulfides and elemental sulfur using high sensitivity cones combined with the addition of nitrogen by laser ablation MC-ICP-MS

The sulfur isotope is an important geochemical tracer in diverse fields of geosciences. In this study, the effects of three different cone combinations with the addition of N₂ on the performance of in situ S isotope analyses were investigated in detail. The signal intensities of S isotopes were improved by a factor of 2.3 and 3.6 using the X skimmer cone combined with the standard sample cone or the Jet sample cone, respectively, compared with the standard arrangement (H skimmer cone combined with the standard sample cone). This signal enhancement is important for the improvement of the precision and accuracy of in situ S isotope analysis at high spatial resolution. Different cone combinations have a significant effect on the mass bias and mass bias stability for S isotopes. Poor precisions of S isotope ratios were obtained using the Jet and X cones combination at their corresponding optimum makeup gas flow when using Ar plasma only. The addition of 4–8 ml min⁻¹ nitrogen to the central gas flow in laser ablation MC-ICP-MS was found to significantly enlarge the mass bias stability zone at their corresponding optimum makeup gas flow in these three different cone combinations. The polyatomic interferences of OO, SH, OOH were also significantly reduced, and the interference free plateaus of sulfur isotopes became broader and flatter in the nitrogen mode (N₂ = 4 ml min⁻¹). However, the signal intensity of S was not increased by the addition of nitrogen in this study. The laser fluence and ablation mode had significant effects on sulfur isotope fractionation during the analysis of sulfides and elemental sulfur by laser ablation MC-ICP-MS. The matrix effect among different sulfides and elemental sulfur was observed, but could be significantly reduced by line scan ablation in preference to single spot ablation under the optimized fluence. It is recommended that the d₉₀ values of the particles in pressed powder pellets for accurate and precise S isotope analysis should be less than 10 μm. Under the selected optimized analytical conditions, excellent agreements between the determined values and the reference values were achieved for the IAEA-S series standard reference materials and a set of six well-characterized, isotopic homogeneous sulfide standards (PPP-1, MoS₂, MASS-1, P-GBW07267, P-GBW07268, P-GBW07270), validating the capability of the developed method for providing high-quality in situ S isotope data in sulfides and elemental sulfur.     

Reduction of irradiation off-odor and lipid oxidation in ground beef by α-tocopherol addition and the use of a charcoal pack

A combination of a charcoal pack during irradiation and α-tocopherol addition into ground beef was applied to eliminate an irradiation characteristic off-odor and to retard the lipid oxidation caused by the irradiation process. Ground beef was mixed with 200 ppm α-tocopherol and gamma irradiated with 0, 5, and 10 kGy with or without a charcoal pack present during the irradiation treatment. The pH of the control group was lower than that of α-tocopherol and charcoal pack treatment initially but increased rapidly and showed higher pH at day 7. Addition of α-tocopherol with or without charcoal pack addition showed lower 2-thiobarbituric acid reactive substances values in irradiated ground beef at days 3 and 7 compared to those without addition. The color of ground beef was not significantly affected by the treatment. However, odor preference result showed that 10 kGy-irradiated ground beef with a combination of charcoal pack and α-tocopherol addition had higher scores than the control group regardless of irradiation. Solid-phase microextraction (SPME) gas chromatograph/mass spectrometry (GC/MS) analysis identified various volatile compounds that were created by irradiation of ground beef. These compounds were reduced or eliminated when a charcoal pack was used during the irradiation process. The results of the present study imply that combination of packaging with a charcoal pack during the irradiation process and addition of α-tocopherol into ground beef is a good method to effectively eliminate an irradiation off-odor and retard the lipid oxidation development in ground beef caused by irradiation.     

Metabolic studies of mesterolone in horses

Mesterolone (1α-methyl-5α-androstan-17β-ol-3-one) is a synthetic anabolic androgenic steroid (AAS) with reported abuses in human sports. As for other AAS, mesterolone is also a potential doping agent in equine sports. Metabolic studies on mesterolone have been reported for humans, whereas little is known about its metabolic fate in horses. This paper describes the studies of both the in vitro and in vivo metabolism of mesterolone in racehorses with an objective to identify the most appropriate target metabolites for detecting mesterolone administration.In vitro biotransformation studies of mesterolone were performed by incubating the steroid with horse liver microsomes. Metabolites in the incubation mixture were isolated by liquid-liquid extraction and analysed by gas chromatography-mass spectrometry (GC-MS) after acylation or silylation. Five metabolites (M1-M5) were detected. They were 1α-methyl-5α-androstan-3α-ol-17-one (M1), 1α-methyl-5α-androstan-3β-ol-17-one (M2), 1α-methyl-5α-androstane-3α,17β-diol (M3), 1α-methyl-5α-androstane-3β,17β-diol (M4), and 1α-methyl-5α-androstane-3,17-dione (M5). Of these in vitro metabolites, M1, M3, M4 and M5 were confirmed using authentic reference standards. M2 was tentatively identified by mass spectral comparison to M1.For the in vivo metabolic studies, Proviron^® (20 tablets × 25 mg of mesterolone) was administered orally to two thoroughbred geldings. Pre- and post-administration urine samples were collected for analysis. Free and conjugated metabolites were isolated using solid-phase extraction and analysed by GC-MS as described for the in vitro studies. The results revealed that mesterolone was extensively metabolised and the parent drug was not detected in urine. Three metabolites detected in the in vitro studies, namely M1, M2 and M4, were also detected in post-administration urine samples. In addition, two stereoisomers each of 1α-methyl-5α-androstane-3,17α-diol (M6 and M7) and 1α-methyl-5α-androstane-3,16-diol-17-one (M8 and M9), and an 18-hydroxylated metabolite 1α-methyl-5α-androstane-3,18-diol-17-one (M10) were also detected. The metabolic pathway for mesterolone is postulated. These studies have shown that metabolites M8, M9 and M10 could be used as potential screening targets for controlling the misuse of mesterolone in horses.     

Qualitative analysis of trace constituents by ion mobility increment spectrometer

Ion mobility increment spectrometry (IMIS) is a high sensitive selective ionization technology for detection and identification of ultra-trace constituents, including toxic compounds, CW-agents, drugs and explosives in ambient air or liquid sample. Like an ion mobility spectrometry (IMS), this technology rests on sampling air containing a mixture of trace constituents, its ionization, spatial separation of produced ions and separated ions detection. Unlike IMS, ions of different types in IMIS are separated by ion mobility increment, α. Value α, is a function of the parameters: electric field strength and form, atmospheric pressure. To exclude the influence of these parameters on an α, the method of explosives identification by a standard compound was suggested. As a standard compound iodine was used. The relationship among the mobility coefficient increments equal to the relationship among the compensation voltage α_i/α_iodine=U_i/U_iodine is determined, where i are ions of 1,3-dinitrobenzene, 1,3,5-trinitrobenzene, p-mononitrotoluene, 2,4-dinitrotoluene and 2,4,6-trinitrotoluene This relationship is practically independent of the above mentioned parameters in the range 25<E/N<90 Td. The limits of the relative error of this relationship are determined both from spectra of individual compounds and nitrocompound-iodine mixtures.     

High-resolution accurate mass measurements of biomolecules using a new electrospray ionization ion cyclotron resonance mass spectrometer

A novel electrospray ionization/Fourier transform ion cyclotron resonance mass spectrometer based on a 7-T superconducting magnet was developed for high-resolution accurate mass measurements of large biomolecules. Ions formed at atmospheric pressure using electrospray ionization (ESI) were transmitted (through six differential pumping stages) to the trapped ion cell maintained below 10^?9 torr. The increased pumping speed attainable with cryopumping (> 10⁵ L/s) allowed brief pressure excursions to above 10^?4 torr, with greatly enhanced trapping efficiencies and subsequent short pumpdown times, facilitating high-resolution mass measurements. A set of electromechanical shutters were also used to minimize the effect of the directed molecular beam produced by the ES1 source and were open only during ion injection. Coupled with the use of the pulsed-valve gas inlet, the trapped ion cell was generally filled to the space charge limit within 100 ms. The use of 10–25 ms ion injection times allowed mass spectra to be obtained from 4 fmol of bovine insulin (M_r 5734) and ubiquitin (M_r 8565, with resolution sufficient to easily resolve the isotopic envelopes and determine the charge states. The microheterogeneity of the glycoprotein ribonuclease B was examined, giving a measured mass of 14,898.74 Da for the most abundant peak in the isotopic envelope of the normally glycosylated protein (i.e., with five mannose and two N-acetylglucosamine residues (an error of approximately 2 ppm) and an average error of approximately 1 ppm for the higher glycosylated and various H₃PO₄ adducted forms of the protein. Time-domain signals lasting in excess of 80 s were obtained for smaller proteins, producing, for example, a mass resolution of more than 700,000 for the 4⁺ charge state (m/z 1434) of insulin.     

Signal enhancement in desorption nanoelectrospray ionization by custom‐made inlet with pressure regulation

The efficiency of desorption/ionization becomes more critical as the sampled surface area decreases. Desorption electrospray and desorption nanoelectrospray belong to ambient ionizations and enable direct surface analysis including mass spectrometric imaging. Lateral resolution in tens of micrometers was demonstrated for desorption nanoelectrospray previously, but sensitivity of the surface scan can be an issue. For desorption electrospray, the drag force in the source is driven by the flow of used gases and vacuum suction. Ion signal intensity can be improved by controlling the nebulizing gas flow rate or auxiliary pumping of a closed compartment in front of the mass spectrometer inlet. Because nanoelectrospray generates charged droplets without the assistance of a nebulizing gas, only vacuum suction drives the gas flow. In this study, the effect of pressure drop between the atmospheric and evacuated region of a mass spectrometer on the ion signal intensity was investigated for desorption nanoelectrospray. A modification of the commercial inlet was designed. An auxiliary pump was directly connected to an inner compartment of the modified mass spectrometer inlet through a needle valve that enabled the regulation of the reduced pressure. Adjustment of the pressure drop significantly increased signal intensity (more than one order of magnitude in some cases). To a lesser extent, the temperature of a heated capillary (an integral part of the inlet) also influenced the signal intensity. The applicability of desorption nanoelectrospray equipped with pressure regulation was demonstrated by the analysis of synthetic cathinones or a pill of paracetamol. Because pressure in the inlet depends on the diameters of orifices and the power of vacuum systems of mass spectrometers, the effect of the pressure regulation can be different for different instruments. Nevertheless, the presented results confirmed the importance of pressure drop‐driven transport for desorption nanoelectrospray efficiency and can encourage its new applications.     

A novel method for analyzing solanesyl esters in tobacco leaves using atmospheric pressure chemical ionization/mass spectrometer

A direct and simple method for analyzing solanesyl esters found in tobacco leaves was developed. Sample preparation was performed by accelerated solvent extractor 200 (ASE200™) using n-hexane followed by evaporating solution in vacuo and dissolving residue with acetone. The separation of analytes was conducted through high-performance liquid chromatography (HPLC) equipped with an SIL-C18/5C™ column and the non-aqueous reversed phase chromatography (NARP) technique using acetone and acetonitrile as the mobile phase with a linear gradient. Atmospheric pressure chemical ionization/mass spectrometer (APCI/MS) in positive mode was used to detect solanesyl esters in the following conditions: capillary voltage 4000 V, corona current 10 μA, drying gas flow 5 mL/min, fragmentor voltage 200 V, nebulizer pressure 60 psi, and vaporizer temperature 500 °C. Each solanesyl ester was identified by the comparison of analyte with synthesized solanesyl esters. Quantification was conducted by selected ion monitoring (SIM) mode in order to detect the specific product ion (613.6 m/z) fragmented from solanesyl ester. The calibration curve was made in the range of 0.1–40 μg/mL with a regression coefficient over 0.999 on almost all solanesyl esters. The limit of detection (LOD) and limit of quantification (LOQ) ranged from 0.01 to 0.05 μg/mL and from 0.03 to 0.15 μg/mL, respectively, on the SIM mode of MS for quantification. Recovery (%) ranged from about 80 to 120%. The direct quantification using the developed method succeeded in showing a different amount and composition of solanesyl esters among various tobacco leaves.     

Using high resolution and dynamic reaction cell for the improvement of the sensitivity of direct silicon determination in uranium materials by inductively coupled plasma mass spectrometry

The paper describes solving the problem of direct silicon determination at low levels in uranium materials, caused by the spectral interferences of polyatomic ions and the high value of blank levels, using inductively coupled plasma mass spectrometry (ICP MS). To overcome the interference problem, two primary techniques have been applied: double focusing high-resolution ICP MS and dynamic reaction cell (DRC) filled with highly reactive ammonia gas. All measurements were performed at high resolution (m/Δm = 4000) on an Element-2 mass spectrometer and pressurized mode of a dynamic reaction cell on an Elan DRC II mass spectrometer. The ways to reducing background levels are investigated. The effects of operating conditions, such as plasma parameters, DRC system original parameters, and uranium matrix influence on the analytical signals of silicon at m/z = 28 have been observed for different mass spectrometer types. The detection limits and the random error characteristics (relative standard deviation) of silicon determination in uranium materials were estimated.