Hydrolytic degradation of poly[(4,4′-oxydiphenylene)pyromellitic amido acid] in concentrated sulphuric acid and in dimethylformamide via hydrodynamic investigations

Translational diffusion and viscosity measurements were performed for poly[(4,4′-oxydiphenylene)pyromellitic amido acid] in DMF, LiCl/DMF, and 96% H₂SO₄ solutions to characterise the rate of the polymer degradation in 96% H₂SO₄ in comparison with its relative stability in organic solutions. The hydrodynamic data were obtained in different stages of hydrolytic polymer degradation at various temperatures from 20 to 80 °C. The mechanism of the degradation is discussed as well as the possibility of molecular investigations of the polymer under conditions of quasi-stable solution.     

Preparation of phosphorus-containing polymers. XXV. Polyamide-imides that contain phenoxaphosphine rings

New phenoxaphosphine-containing polyamide-imides were prepared by cyclodehydration of the polyamide-amic acids obtained from 8-chloroformyl-10-phenylphenoxaphosphine-2,3-dicarboxylic anhydride 10-oxide and diamines by a low-temperature solution polycondensation. Polymers with reduced viscosities of 0.10–0.59 dl/g in DMA or concentrated H₂SO₄ at 30°C were obtained in 64–97% yields. All the polyamide-imides were soluble in m-cresol, concentrated H₂SO₄, and dichloroacetic acid and some of them were soluble in DMF, DMA, and DMSO; the polyamide-imides had better solubility in organic solvents than phenoxaphosphine-containing polyimides. The phenoxaphosphine-containing polyamide-imides derived from aromatic diamines exhibited excellent thermal properties and little degradation below about 400°C, whereas the polymers from aliphatic diamines began to lose weight at about 250°C. They appeared to have thermal stability between phenoxaphosphine-containing polyimides and polyamides. These polyamide-imides exhibited self-extinguishing behavior.     

Hydrolytic degradation and thermal stability of poly(naphthylimides) based on naphthalene-1,4,5,8-tetracarboxylic dianhydride and bis(naphthalic anhydrides)

The molecular properties of a number of new poly(naphthylimides) derived from naphthalene-1,4,5,8-tetracarboxylic dianhydride and bis(naphthalic anhydrides) have been studied. On the basis of hydrodynamic studies of the polymers at various stages of their thermal degradation in 96% H₂SO₄ and thermogravimetric measurements, the hydrolytic stability and thermooxidative resistance of the polymers have been compared. A correlation between the experimental data and the chemical structure of molecular chains has been established.     

Soluble aromatic polyamide and polyimides derived from di(aminophenyl) acetylenediurea

New aromatic polyamide and polyimides were prepared from di(aminophenyl)acetylenediurea. In addition, model compounds were synthesized and their IR spectra were in agreement with those of the corresponding polymers. The polymers were amorphous and readily soluble in polar aprotic solvents (DMF, NMP, DMSO) and certain acids (H₂SO₄, CCl₃COOH). The hydrophilicity of polyamide was estimated by measuring the isothermal water absorption. The polyamide softened at 260°C but no softening was observed for polyimides. The glass transition temperatures of polymers were determined by the TMA method and they were in the range of 235–310°C. The polymers were stable up to 359–404°C in N₂ or air and afforded char yields of 53–65% at 800°C in N₂. © 1996 John Wiley & Sons, Inc.     

New benzimidazole-2-yl-substituted polybenzimidazoles: Synthesis, properties, and hydrodynamic characteristics

The synthesis of novel benzimidazole-2-yl-substited polybenzimidazoles and initial compounds has been described. The polymers are studied by FTIR spectroscopy, TGA, and TMA. The hydrodynamic properties of macromolecules are investigated by translational diffusion and viscometry in 96% H₂SO₄; the molecular characteristics of the polymers are determined. Positive temperature dependences for intrinsic viscosities of the polymers are obtained. The polymers under study possess high hydrolytic stability with respect to sulfuric acid solutions up to 150°C and high thermal stability in the bulk. The TGA data correlate with the chemical structure of the polymers. The new polybenzimidazoles may be used as materials for the production of medium-temperature proton-conducting membranes.     

Synthesis and Characterization of Organosoluble Polyimides Containing Pyridyl Moiety with Ether Linkages

Two novel diamine monomers, bis(4‐amino‐3,5‐dimethylphenyl)‐3‐pyridyl methane and bis(4‐aminophenoxy‐3,5‐dimethylphenyl)‐3‐pyridyl methane were synthesized. A series of pyridine containing aromatic polyimides derived from the diamines were synthesized through a typical two‐step polymerization method. Most of the polymers show good solubility in NMP, DMAc, DMF, DMSO and CHCl₃ at room temperature. These polyimides exhibit T_g in the range of 249–317°C and 10% wt loss (T₁₀) takes place in the range of 474–564°C in N₂ and 469–558°C in air. The polymers have tensile strength in the range of 88–96 MPa, elongation at break in the range of 8.5–12.5% and tensile modulus in the range of 1.5–2.1 GPa. These polyimides also have low dielectric constant (3.26–3.64 at 1 KHz and 3.24–3.61 at 10 KHz) and low moisture absorption (0.42–0.89%).     

New sulfonated engineering polymers via the metalation route. I. Sulfonated poly(ethersulfone) PSU Udel® via metalation-sulfination-oxidation

A new process has been developed for the sulfonation of arylene polymers which can be lithiated, like polysulfone Udel®. The sulfonation process consists of the following steps: (1) lithiation of the polymer at temperatures from −50 to −80°C under argon, (2) gassing of the lithiated polymer with SO₂; (3) oxidation of the formed polymeric sulfinate with H₂O₂, NaOCl, or KMnO₄; (4) ion-exchange of the lithium salt of the sulfonic acid in aqueous HCl. The advantages of the presented sulfonation procedure are: (1) in principle all polymers which can be lithiated can be subjected to this sulfonation process; (2) by this sulfonation procedure the sulfonic acid group is inserted into the more hydrolysis-stable part of the molecule; (3) this process is ecologically less harmful than many common sulfonation procedures. The sulfonated polymers were characterized by NMR, titration and elemental analysis, by IR spectroscopy, and by determination of ionic conductivity. Also the hydrolytic stability of the sulfonated ion-exchange polymers was investigated. Polymers with an ion-exchange capacity of 0.5 to 3.2 mequiv SO₃H/g Polymer have been synthesized and characterized. The following results have been achieved: membranes made from the sulfonated polymers show good conductivity, good permselectivity (>90%), and good hydrolytic stability in 1N HCl and water at temperatures up to 80°C. © 1996 John Wiley & Sons, Inc.     

Crosslinkable aromatic polyimides containing 2,3-dicyanopyrazine rings

New crosslinkable aromatic polyimides were synthesized from 2,3-dicyano-5,6-di(aminophenyl)pyrazine ( 1b ) and 2,3-dicyanopyrazino [5,6–9,10] diaminophenanthrene ( 2b ). They were characterized by viscosimetry, IR, NMR, x-ray, DTA, TMA, TGA, and isothermal gravimetric analysis. The polyimides derived from 1b were amorphous whereas those prepared from 2b showed microcrystalline or crystalline character. The polymers were soluble in polar aprotic solvents (DMF, NMP, DMSO) at ambient temperature or upon heating. They dissolved also completely or partially in certain hot inorganic and organic acids (H₂SO₄, CCl₃COOH). Their glass transition temperatures were in the range of 257–370°C. The crosslinked polymers obtained after an appropriate thermal treatment, were stable up to 397–426°C in N₂ or air and afforded anaerobic char yields of 62–75% at 800°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1303–1311, 1997     

Preparation of phosphorus-containing polymers—XV. Preparation of phosphorus-containing polyamide-imides from N,N′-bis(4-carboxyphthalimido)-3,3′-diphenylalkylphosphine oxide and aromatic diacetamides

Phosphorus-containing polyamide-imides were prepared from N,N′-bis(4-carboxyphthalimido)-3,3′-diphenylalkylphosphine oxide and aromatic diacetamido derivatives by acidolysis; the reaction conditions are discussed. The resulting polymers were fairly soluble in DMA, DMF and conc. H₂SO₄; the reduced viscosities of polymers in DMA or cone. H₂SO₄ (0.2 g/dl) at 30° were 0.19–0.32. The phosphorus-containing polymers have good thermal stability, and are self-extinguished immediately after the flame is removed. Most of the i.r. absorption bands of polymers vanished on heating at above 600°.     

Preparation of phosphorus-containing polymers—XXIII: Phenoxaphosphine-containing polyimides

New phenoxaphosphine-containing polyimides were synthesized from 10-phenylphenoxaphosphine-2,3,7,8-tetracarboxylic dianhydride 10-oxide (IV) and diamines via polyamic acids in two steps. (IV) was prepared by dehydration of 10-phenylphenoxaphosphine-2,3,7,8-tetracarboxylic acid 10-oxide (III) derived from 2,3,7,8-tetramethyl-10-phenylphenoxaphosphine (I) or 2,3,7,8-tetramethyl-10-phenylphenoxaphosphine 10-oxide (II) by pyridine-permanganate oxidation. (I) was synthesized from bis(3,4-dimethylphenyl)ether and phenylphosphonous dichloride by the Friedel-Crafts reaction. The resulting polyimides had reduced viscosities of 0.13–0.84 di/g in cone H₂SO₄ at 30°. They were also soluble in dichloroacetic acid and some of them dissolved in DMA, DMSO. DMF and chloroform. Aromatic phenoxaphosphine-containing polyimides exhibited excellent thermal properties and hardly degraded below about 500°; the aliphatic polyimides decomposed at around 500. The aromatic polyimides had thermal stability similar or superior to aromatic polypyromellitimides and better heat resistance than linear open-chain phosphorus-containing polyimides. These polyimides showed retardance to inflammation.     

Synthesis and characterization of polyimides containing heterocyclic units

Five new polyimides containing phenoxaphosphine as well as dibenzothiophene, phenoxathiin, and thianthrene units have been synthesized from 10-phenylphenoxaphosphine-2,3,7,8-tetracarboxylic dianhydride-10-oxide and heterocyclic diamines by the cyclopolycondensation method. These polyimides had inherent viscosities in the 0.75–1.10 dL/g range in conc. H₂SO₄ at 30°C. All the polymers were characterized by elemental analysis, density, solubility, crystallinity, IR spectra, and thermal methods.     

Synthesis and crosslinking of cyano-substituted polyamides and polyimides prepared from 1-(2,2-dicyano-1-hydroxyviyl)-3,5-diaminobenzene,sodium salt

3,5-Dinitrobenzoyl chloide was condensed with malononitrile in the presence of sodium hydroxide under phase-transfer conditions to afford 1-(2,2-dicyano-1-hydroxyvinyl)-3,5-dinitrobenzene, sodium salt, which was catalytically hydrogenated to the corresponding diamine. The latter was used as starting material for the preparation of unsaturated cyanosubstituted polyamides and polyimides. The polymers were soluble in polar aprotic solvents, dilute sodium hydroxide, and certain strong inorganic and organic acids. Upon curing at 300°C for 65 h, crosslinked polymers were obtained that were stable up to 392–404°C in N₂ or air and afforded an anaerobic char yield of 60–71% at 800°C. Their glass transition temperatures as determined by thermal mechanical analysis (TMA) were 221–275°C. © 1995 John Wiley & Sons, Inc.     

Heat-resistant polymers containing thianthrene analogs units. I. Polyimides

Polyimides that contained thianthrene and dibenzo-p-dioxins units were synthesized. The tricyclic fused rings were successfully incorporated by polymerizing the diamines of the units with aromatic tetracarboxylic dianhydrides. The resulting polyamic acids were converted to polyimides by thermal cyclodehydration. The influence of the tricyclic units on the properties of the polyimides has been investigated. Polyimides that contained dibenzo-p-dioxins (ODP) exhibited sufficient thermal stability but were insoluble even in concentrated sulfuric acid. The introduction of a methyl group did not produce an appreciable increase in solubility. Thianthrene polyimides were considerably less stable than the equivalent polymers derived from open-chain diamine, 4,4′-diaminodiphenyl sulfide but were partly soluble in acid solvents. The results are discussed in terms of packing the polymer molecules.     

Polycondensation of pyridine-2,6-dicarboxylic acid with some di- and tetraamino compounds

Pyridine-2,6-dicarboxylic acid phenyl ester was condensed with 3,3′-diaminobenzidine and 3,3′,4,4′-tetraaminodiphenyl ether. Polyamides were also synthesized by condensation of the above ester with p-phenylenediamine, benzidine, 4,4′-diaminodiphenyl sulfide and 4,4′-diaminodiphenyl sulfone. These amides had higher inherent viscosities and greater thermal stability than was reported before. Model compounds of imidazoles were prepared by condensation of the same ester with o-phenylenediamine and 2,3-diaminopyridine and of polyamides by condensation with aniline and 2-aminopyridine. In the case of the polyimidazole, the completely closed ring of imidazole did not form. The ultraviolet spectra of model compounds were compared with those of the polymers. The thermogravimetric curves show that the polymers are stable up to more than 400°C under argon atmosphere. All polymers were insoluble in most organic and inorganic solvents. They dissolved only partially in DMSO and DMF. Inherent viscosity was measured for the soluble polymer fraction.     

Preparation of phosphorus-containing polymers—XVI. Synthesis of phosphorus-containing polyanhydride-imides

Phosphorus-containing polyanhydride-imides were synthesized from N,N-bis(4-carboxyphthalimido)-3,3′-diphenylalkylphosphine oxide, 3,3′-[N,N′-bis(4-carboxyphthalimido)]benzophenone and their mixtures in two steps via the diacetyl derivatives of the bisimide-carboxylic acids. The resulting polymers have reduced viscosities of 0.06–0.14 dl/g and are soluble in polar aprotic solvents such as DMA, DMF and DMSO, and conc. H₂SO₄ etc. They have good hydrolytic stability for moisture and water. Phosphorus-containing polymers have little heat-resistance and poor flame-retardance. The benefit of incorporating phosphorus in the polymers is small.     

Solubility and transport of water vapor in some 6FDA-based polyimides

Permeability, diffusion, and solubility coefficients for H₂O vapor in four different 6FDA-based polyimides were determined at temperatures between 25 and 45°C and over a wide range of relative humidities. The solubility of H₂O vapor in some of the polyimides studied can be described by the “dual-mode sorption” model whereas in other polyimides it is represented by the Flory-Huggins equation, which suggests that the latter polymers are plasticized by H₂O. The solubility of H₂O vapor in the polyimides decreases as the temperature is raised and increases with increasing polarity of the polymer. The diffusion coefficients for H₂O in the polyimides studied either increase or pass through a weak maximum with increasing H₂O activity, or concentration in the polymers. The latter behavior is probably due to a clustering of H₂O molecules in the polyimides at higher H₂O activities or concentrations. The diffusion coefficients for H₂O decrease as the chain-packing density of the polyimides increases. The permeability coefficients for H₂O vapor in 6FDA-based polyimide membranes either increase slightly or are constant as the H₂O activity is increased. The experimental values of the permeability coefficients are consistent with the values determined from diffusion and solubility coefficients. The permeability of the polyimides to H₂O vapor appears to be controlled by the solubility of H₂O in the polymers. The polyimides studied exhibit a very high selectivity for H₂O vapor relative to CH_4, and therefore are potentially useful membrane materials for the dehydration of natural gas. ©1995 John Wiley & Sons, Inc.     

The preparation of novel silica modified polyimide membranes: synthesis,characterization, and gas separation properties

In this study, new monomers having siloxane groups were synthesized as an intermediate for preparation of siloxane modified polyimide polymers. Then with these monomers, the synthesis of uncrosslinked and crosslinked polyimide–siloxane hybrid polymer membranes were achieved. The purposes of the preparation of modified polyimides were to modify the thermal and chemical stability, and mechanical strength of polyimides, and to improve the gas separation properties of polymers. The new diamine monomer having siloxane groups was prepared from 3,5‐diaminobenzoic acid (3,5‐DABA) and 3‐aminopropyltrimethoxysilane (3‐APTMS) in N‐methyl‐2‐pyrollidone (NMP) at 180°C. The modified polyimide membranes having different amount of siloxane groups were synthesized from pyromellitic dianhydride (PMDA), 4,4‐oxydianiline (ODA), and 3,5‐diaminobenzamido‐N‐propyltrimethoxy silane (DABA/PTMS) in NMP using a two‐step thermal imidization process. The synthesis of modified polyimide membranes were characterized by Fourier transform infrared spectroscopy (FTIR). The thermal analysis of the polyimides were carried out by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Water absorption and swelling experiments were also carried out for the investigation of structural properties of polymers. FTIR observations confirmed that the polyimide membranes with new diamine intermediate were successfully obtained. Thermal analysis showed that the uncrosslinked copolyimides exhibited two glass transition temperatures, indicating that they were separated microphases and it was found that all the modified copolyimides had showed higher glass transition temperature (T_g) than unmodified polyimides. The separation properties of the prepared polyimide membranes were also characterized by permeability for O₂ and N₂ gases and ideal selectivity values were calculated. Copyright © 2009 John Wiley & Sons, Ltd.     

A study of benzobisoxazole and benzobisthiazole compounds and polymers under hydrolytic conditions

The stability of benzobisoxazole and benzobisthiazole compounds and polymers under hydrolytic conditions was studied. 2,6-Bis(4-tert-butylphenyl)benzo[1,2-d;4,5-d′]bisoxazole (1) dissolved in acetonitrile containing sulfuric acid and water at 80°C is stable. A suspension of 2,6-bis[4-(2-benzoxazoyl)phenyl]benzo[1,2-d;5,4-d′]bisoxazole (2) in 0.2 N H₂SO₄ or 0.2 N NaOH solution at 100°C for 21 days is stable. The intrinsic viscosity of a poly(p-phenylene)benzobisoxazole (PBO) fiber sample soaked in 0.2 N H₂SO₄, water with 1 wt % polyphosphoric acid (PPA), or 0.2 N NaOH remained the same. Under very severe hydrolytic conditions such as dissolution of compound 2 or PBO in PPA or methanesulfonic acid with residual water followed by coagulation in water, benzobisoxazole underwent bond cleavage to generate carboxylic acid and o-aminophenol functional groups. This is in contrast to an earlier hypothesis that the decrease in intrinsic viscosity under these conditions was due to chain association. Poly(p-phenylene)benzobisthiazole (PBT) also underwent bond cleavage under these very severe conditions, which are unlikely to be encountered in normal applications. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2637–2643, 1999     

Polyanhydrides: Stability and novel composition

New types of polyanhydrides with advantageous properties with respect to biomedical use were synthesized. The first are aliphatic-aromatic homopolyanhydrides of the structure: -(OOC-C₆H₄-O(CH₂)x- CO-)_n (=1−10). These polymers display a zero-order hydrolytic degradation profile for two to ten weeks, the time period of degradation is a function of the length of the aliphatic chain. Stability studies under anhydrous conditions showed that these polymers underwent reversible self-depolymerization in chloroform but were stable in solid state for over 6 months at 25°C. The second type of polymer, unsaturated polyanhydride of the structure: [-(OOC-CH=CH-CO)_x-(OOC-R-CO)_y-]_n, have the advantage of secondary polymerization of double bonds to create a crosslinked matrix. These polymers were prepared from the corresponding diacids polymerized by melt condensation or in solution. Molecular weights of up to 44 000 and 30 000 were achieved for polyanhydrides of p-carboxyphenoxyalkanoic acid and fumaric acid, respectively.     

Novel processable aromatic thermoplastic polyimides: Films,adhesives, moldings,and graphite composites

Novel hot-melt type flexible, tough, thermally stable, processable, thermoplastic, aromatic polyimides have been synthesized involving reaction of a keto-ether containing diamine with hinged aromatic dianhydrides followed by thermal and chemical cyclodehydration. Inherent viscosity in DMAC at 35°C of the synthesized polymers ranged 1.02 to 1.4 dl/g (0.5% solution). The polymers showed a glass transition temperature (T_g) of 250°C to 180°C as determined by differential scanning calorimetry (DSC) and thermomechanical analysis (TMA). Thermogravimetric analysis showed polymer stability up to 510°C, in both air and nitrogen atmospheres. All the polymers have shown good melt-flow. Films of 1.5–2.8 ml thickness were made and tested for mechanical properties at room temperature, 177°C and 210°C. The developed films are suitable for adhesion of Ti/Ti specimens and showed a lap shear strength of 5575 psi. Melt-fusion of the polymers gave tough moldings. Graphite cloth composites have been made and tested for mechanical properties.