Dynamics of phase transitions induced by femtosecond laser pulse irradiation of indium phosphide

The structural transformation dynamics of single-crystalline indium phosphide (InP) irradiated with 150 fs laser pulses at 800 nm has been investigated by means of time-resolved reflectivity measurements covering a time window from 150 fs up to 500 ns. The results obtained show that for fluences above a threshold of 0.16 J/cm² thermal melting of the material occurs on the timescale of 1–2 ps. The evolution of the reflectivity on a longer timescale reveals the reflectivity of the liquid phase and shows resolidification times typically around 10–30 ns after which an amorphous layer several tens of nanometers thick is formed on the surface. This amorphous layer significantly alters the optical properties of the surface and finally leads to a reduced ablation threshold for subsequent laser pulses. Single-pulse ablation at higher fluences (>0.23 J/cm²) is preceded by an ultrafast phase transition (non-thermal melting) occurring within 400 fs after the arrival of the pulse to the surface. PACS 79.20.Ds; 78.47.+p; 64.70.-p     

Influence of film thickness on laser ablation of hydrogenated amorphous carbon films

Single-pulse damage thresholds of hydrogenated amorphous carbon (a-C:H) films were measured for 8-ns laser pulses at 532-nm wavelength. Layer thicknesses from below the optical penetration depth to above the thermal diffusion length (60 nm–13 μm) were examined. After correction of the damage-threshold values for the fraction of energy effectively absorbed by the material, the damage threshold was found to increase linearly with the layer thickness, also for film thicknesses below the optical penetration depth of a-C:H. The threshold fluence reached the bulk value for a layer thickness equal to the thermal diffusion length. The thermal diffusion coefficient was obtained from fitting the experimental data. Several phenomena like graphitization, blistering, exfoliation, and ablation were observed for different fluence regimes and film thicknesses. PACS 79.20.Ds; 06.60.Jn; 78.66.Jg     

Direct observation of laser-induced crystallization of a-C:H films

The post-growth modification of diamond-like amorphous hydrogenated carbon a-C:H films by laser treatment has been studied by transmission electron microscopy and Raman spectroscopy. a-C:H films grown on Si substrates by benzene decomposition in a rf glow discharge were irradiated with 15 ns pulses of a KrF-excimer laser with fluences in the range of E=50–700 mJ/cm². At fluences below 100 mJ/cm² an increase in the number of graphitic clusters and in their ordering was evidenced from Raman spectra, while the film structure remained amorphous according to electron microscopy and electron diffraction observations. At higher fluences the appearance of diamond particles of 2–7 nm size, embedded into the lower crystallized graphitic matrix, was observed and simultaneously a progressive growth of graphite nanocrystals with dimensions from 2 nm to 4 nm was deduced from Raman measurements. The maximum thickness of the crystallized surface layer (400 nm) and the degree of laser annealing are limited by the film ablation which starts at E>250 mJ/cm². The laser-treated areas lose their chemical inertness. In particular, chemical etching in chromium acid becomes possible, which may be used for patterning the highly inert carbon films.     

Picosecond laser ablation of SiO2 layers on silicon substrates

In this work, we report on laser ablation of thermally grown SiO₂ layers from silicon wafer substrates, employing an 8–9 ps laser, at 1064 (IR), 532 (VIS) and 355 nm (UV) wavelengths. High-intensity short-pulse laser radiation allows direct absorption in materials with bandgaps higher than the photon energy. However, our experiments show that in the intensity range of our laser pulses (peak intensities of <2×10¹² W/cm²) the removal of the SiO₂ layer from silicon wafers does not occur by direct absorption in the SiO₂ layer. Instead, we find that the layer is removed by a “lift off” mechanism, actuated by the melting and vaporisation of the absorbing silicon substrate. Furthermore, we find that exceeding the Si melting threshold is not sufficient to remove the SiO₂ layer. A second threshold exists for breaking of the layer caused by sufficient vapour pressure. For SiO₂ layer ablation, we determine layer thickness dependent minimum fluences of 0.7–1.2 J/cm² for IR, 0.1–0.35 J/cm² for VIS and 0.2–0.4 J/cm² for UV wavelength. After correcting the fluences by the reflected laser power, we show that, in contrast to the melting threshold, the threshold for breaking the layer depends on the SiO₂ thickness.     

Comparative study between IR and UV laser radiation applied to the removal of graffitis on urban buildings

The present article focuses on a comparison between cleaning process of graffitis on urban buildings by using laser radiation at 308 nm (XeCl excimer laser) and 1064 nm (Nd:YAG laser). Laser-induced breakdown spectroscopy (LIBS) elemental analysis was applied as real-time diagnostic technique, safeguarding against possible damage of the substrate during ablation rate studies. The morphological analysis of the etched surfaces by optical microscopy and environmental scanning electron microscopy reveals remarkable features of interest to understand the wavelength dependence of the ablation efficiency. The ablation threshold fluences of different paints sprayed on several substrates were determined applying a photoacoustic technique. To remove graffitis from urban buildings the laser radiation at 1064 nm was observed to be the most efficient wavelength, supporting the best result.     

Femtosecond laser ablation characteristics of nickel-based superalloy C263

Femtosecond laser (180 fs, 775 nm, 1 kHz) ablation characteristics of the nickel-based superalloy C263 are investigated. The single pulse ablation threshold is measured to be 0.26±0.03 J/cm² and the incubation parameter ξ=0.72±0.03 by also measuring the dependence of ablation threshold on the number of laser pulses. The ablation rate exhibits two logarithmic dependencies on fluence corresponding to ablation determined by the optical penetration depth at fluences below ∼5 J/cm² (for single pulse) and by the electron thermal diffusion length above that fluence. The central surface morphology of ablated craters (dimples) with laser fluence and number of laser pulses shows the development of several kinds of periodic structures (ripples) with different periodicities as well as the formation of resolidified material and holes at the centre of the ablated crater at high fluences. The debris produced during ablation consists of crystalline C263 oxidized nanoparticles with diameters of ∼2–20 nm (for F=9.6 J/cm²). The mechanisms involved in femtosecond laser microprocessing of the superalloy C263 as well as in the synthesis of C263 nanoparticles are elucidated and discussed in terms of the properties of the material.     

Chemical, morphological and accumulation phenomena in ultrashort-pulse laser ablation of TiN in air

Ultrashort-pulse laser ablation (τ=130 fs, λ=800 nm, repetition rate 2–20 Hz) of titanium nitride was investigated for laser fluences between 0.3 and 4.5 J/cm² using the direct focusing technique in air. The influence of the laser pulse number and the peak fluence was investigated by means of several surface analytical techniques (optical microscopy, dynamic friction atomic force microscopy, scanning Auger electron microscopy and small-spot electron spectroscopy for chemical analysis). The correlation of the results about optical, physical and chemical properties of the irradiated areas allows us to propose a simple oxidation model, which explains different observed phenomena associated with surface damage such as mound formation and crater widening and clarifies the incubation behavior reported earlier for this material. Received: 8 May 2000 / Accepted: 9 May 2000 / Published online: 13 September 2000     

Model for laser-induced thermal degradation and ablation of polymers

Ablation of organic polymers is described on the basis of photothermal bond breaking within the bulk material. Here, we assume a first-order chemical reaction, which can be described by an Arrhenius law. Ablation starts when the density of broken bonds at the surface reaches a certain critical value. In order to understand the ablation behavior near the threshold fluence, φ_th, non-stationary regimes must be considered. The present treatment reveals several qualitative differences with respect to models that treat ablation as a surface process: (i) Ablation starts sharply with a front velocity that has its maximum value just after the onset. (ii) The transition to the quasi-stationary ablation regime is faster. (iii) Near threshold, the ablated depth h has a square-root dependence on laser fluence, i.e., h∝(φ-φ_th)^1/2. The ablation velocity is very high even near φ_th. (iv) With φ≈φ_th ablation starts well after the laser pulse. (v) The depletion of species is responsible for the Arrhenius tail observed with fluences φ≤φ_th. (vi) Residual modification of material has maximum near the threshold. (vii) Stationary regimes of ablation demonstrate change of effective activation energy with laser intensity. The model calculations are applied to Polyimide (Kapton^TM H). Here, differences in single-pulse ablated depth determined from mass loss and profilometry should be about 10 nm. Received: 16 February 1999 / Accepted: 18 February 1999 / Published online: 28 April 1999     

Optical field enhancement effects in laser-assisted particle removal

We report on the role of local optical field enhancement in the neighborhood of particles during dry laser cleaning (DLC) of silicon wafer surfaces. Samples covered with spherical colloidal particles (PS, SiO₂) and arbitrarily shaped Al₂O₃ particles with diameters from 320–1700 nm were cleaned using laser pulses with durations from 150 fs to 6.5 ns and wavelengths ranging from 400–800 nm. Cleaned areas were investigated with scanning electron and atomic force microscopy. Holes in the substrate with diameters of 200–400 nm and depths of 10–80 nm, depending on the irradiation conditions, were found at the former positions of the particles. For all pulse durations analyzed (fs, ps, ns), holes are created at laser fluences as small as the threshold fluence. Calculations of the optical field intensities in the particles’ neighbourhood by applying Mie theory suggest that enhancement of the incident laser intensity in the near field of the particles is responsible for these effects. DLC for sub-ns pulses seems to be governed by the local ablation of the substrate rather than by surface acceleration. Received: 31 May 2000 / Accepted: 7 September 2000 / Published online: 22 November 2000     

Picosecond laser ablation of thin copper films

The ablation process of thin copper films on fused silica by picosecond laser pulses is investigated. The ablation area is characterized using optical and scanning electron microscopy. The single-shot ablation threshold fluence for 40 ps laser pulses at 1053 nm has been determinated toF _thres = 172 mJ/cm². The ablation rate per pulse is measured as a function of intensity in the range of 5 × 10⁹ to 2 × 10¹¹ W/cm² and changes from 80 to 250 nm with increasing intensity. The experimental ablation rate per pulse is compared to heat-flow calculations based on the two-temperature model for ultrafast laser heating. Possible applications of picosecond laser radiation for microstructuring of different materials are discussed.     

Evolution of InP surfaces under low fluence pulsed UV irradiation

An InP wafer was irradiated in air by a series of UV pulses from a nitrogen laser with fluences of 120 mJ/cm² and 80 mJ/cm². These fluences are below the single-pulse ablation threshold of InP. Over the studied region the distribution of the radiation intensity was uniform. The number of pulses varied from 50 to 6000. The evolution of the surface morphology and structure was characterized by atomic force microscopy, optical microscopy and Raman spectroscopy. The relationship between mound size and the number of pulses starts out following a power law, but saturates for a sufficiently high number of pulses. The crossover point is a function of fluence. A similar relation exists for the surface roughness. Raman spectroscopic investigations showed little change in local crystalline structure of the processed surface layer.     

Microscopic investigation of single-crystal diamond following ultrafast laser irradiation

We present a structural investigation of single-crystal diamond following ultrafast laser irradiation of the surface and the bulk material. Optical microscopy, atomic force microscopy, scanning electron microscopy, and focused-ion beam and transmission electron microscopy techniques were utilized to selectively examine the final state of the samples. Laser induced periodic surface structures (LIPSS) with high- and low-spatial frequencies were obtained with multiple-pulse surface irradiation under both stationary and translated target conditions. High magnification transmission electron microscopy analysis of cross sections of the LIPSS revealed modified layers of a few tens of nanometers in thickness capping the crystalline diamond matrix. Sub-surface irradiation of diamond at high laser fluences led to damaged regions and cracks in the bulk material. When translational bulk irradiation of the diamond was performed, substantially sub-wavelength periodic structures were observed at the unpolished side facet of the diamond plate where the laser focus was translated out of the bulk. Spatial periods were 140 nm and the structures largely consisted of single-crystal diamond with a 10 nm modified layer. Finally, preliminary studies of single-shot laser ablation craters at high laser fluences exhibited suppression of material removal for peak values above 45 J/cm².     

Effect of spot size on cone formation in a XeCl laser ablation of polyethersulfone films

Radiation from the UV excimer lasers, with the fluence above the ablation threshold, can etch the polymer surfaces by photoablation. In some cases different microstructures may appear on the surface during the laser ablation. In this paper the effect of the laser spot size on the cone formation on polyethersulfone films has been investigated. The experiments have been performed with a XeCl laser at the wavelength of 308 nm and at the fluences of 70 and 100 mJ/cm² at air. For the investigation of the effect of the laser spot size on cone formation, the samples were irradiated at two different laser spot sizes of w₁ and w₂ = 0.1 w₁. The morphology of the processed surface was studied by scanning electron microscopy (SEM). It has shown that the shape, size and density of cones change with the change of the laser spot size. Also, the number of pulses and the pulse repetition rate which are needed for threshold of cone formation are affected by the laser beam spot size on the surface.     

KrF pulsed laser ablation of polyimide

In the present paper, polyimide surfaces were processed with pulsed KrF laser radiation at fluences near the ablation threshold. The morphology of the processed surfaces was studied by scanning electron microscopy and chemical analyses performed by electron dispersive spectroscopy. The formation of conical structures was observed for radiation fluences lower than 0.5 J/cm². The areal density of cones increases with the number of pulses and decreases with the radiation fluence. At low fluences (<150 J/cm²), cones are formed due to shadowing by calcium phosphate impurities while for higher fluences the main mechanism of cones formation is believed to be radiation hardening.     

Pulsed laser treatment of gold and black gold thin films fabricated by thermal evaporation

The effect of pulsed laser treatment of metal, and metal blacks, was studied. Gold and black gold thin films were fabricated by thermal evaporation of gold in a vacuum and nitrogen atmosphere respectively. Black gold films were grown in a nitrogen atmosphere at pressures of 200 Pa and 300 Pa. UV pulsed laser radiation (λ = 266 nm, τ = 4 ns), with fluence ranging from 1 mJ·cm⁻² to 250 mJ·cm⁻² was used for the film treatment in a vacuum and nitrogen atmosphere. The nitrogen pressure was varied up to 100 kPa. Surface structure modifications were analyzed by optical microscopy, atomic force microscopy (AFM) and scanning electron microscopy (SEM). Energy dispersive X-ray spectroscopy (EDX) was used for chemical characterization of the samples. A significant dependence of the film optical and structural properties on laser treatment conditions (laser fluence, ambient pressure and number of applied pulses) was found. The threshold for observable damage and initiation of changes of morphology for gold and black gold surfaces was determined. Distinct modifications were observed for fluences greater than 106 mJ·cm⁻² and 3.5 mJ·cm⁻² for the gold and black gold films respectively. Absorbtivity of the black gold film is found to decrease with an increase in the number of laser pulses. Microstructural and nanostructural modifications after laser treatment of the black gold film were observed. EDX analysis revealed that no impurities were introduced into the samples during both the deposition and laser treatment.      

Transient reflectivity and transmission changes during plasma formation and ablation in fused silica induced by femtosecond laser pulses

We have studied the plasma formation and ablation dynamics in fused silica upon irradiation with a single 120 fs laser pulse at 800 nm by using fs-resolved pump-probe microscope. It allows recording images of the laser-excited surface at different time delays after the arrival of the pump pulse. This way, we can extract both the temporal evolution of the surface reflectivity and transmission, at 400 nm, for different spatial positions in the spots (and thus for different local fluences) from single series of images. At fluences well above the visible ablation threshold, a fast and large increase of the reflectivity is induced by the formation of a dense free-electron plasma. The maximum reflectivity value is reached within ≈1.5 ps, while the normalized transmission decreases within ≈400 fs. The subsequent temporal evolution of both transient reflectivity and transmission are consistent with the occurrence of surface ablation. In addition, the time-resolved images reveal the existence of a free-electron plasma distribution surrounding the visible ablation crater and thus formed at local fluences below the ablation threshold. The lifetime of this sub-ablation plasma is ≈50 ps, and its maximum electron density amounts to 5.5×10²² cm⁻³.     

Characterization of excimer laser ablation generated pepsin particles using multi-wavelength photoacoustic instrument

Preparation of organic thin layers on various special substrates using the pulsed laser deposition (PLD) technique is an important task from the point of view of bioengineering and biosensor technologies. Earlier studies demonstrated that particle ejection starts during the ablating laser pulse resulting in significant shielding effects which can influence the real fluence on the target surface and consequently the efficiency of layer preparation. In this study, we introduce a photoacoustic absorption measurement technique for in-situ characterization of ablated particles during PLD experiments. A KrF excimer laser beam (λ=248 nm, FWHM=18 ns) was focused onto pepsin targets in a PLD chamber; the applied laser fluences were 440 and 660 mJ/cm². We determined the wavelength dependence of optical absorption and mass specific absorption coefficient of laser ablation generated pepsin aerosols in the UV–VIS–NIR range. On the basis of our measurements, we calculated the absorbance at the ablating laser wavelength, too. We demonstrated that when the laser ablation generated pepsin aerosols spread through the whole PLD chamber the effect of absorptivity is negligible for the subsequent pulses. However, the interaction of the laser pulse and the just formed particle cloud generated by the same pulse is more significant.     

Picosecond laser ablation of nickel-based superalloy C263

Picosecond laser (10.4 ps, 1064 nm) ablation of the nickel-based superalloy C263 is investigated at different pulse repetition rates (5, 10, 20, and 50 kHz). The two ablation regimes corresponding to ablation dominated by the optical penetration depth at low fluences and of the electron thermal diffusion length at high fluences are clearly identified from the change of the surface morphology of single pulse ablated craters (dimples) with fluence. The two corresponding thresholds were measured as F _th(D1)¹=0.68±0.02 J/cm² and F _th(D2)¹=2.64±0.27 J/cm² from data of the crater diameters D _1,2 versus peak fluence. The surface morphology of macroscopic areas processed with a scanning laser beam at different fluences is characterised by ripples at low fluences. As the fluence increases, randomly distributed areas among the ripples are formed which appear featureless due to melting and joining of the ripples while at high fluences the whole irradiated surface becomes grainy due to melting, splashing of the melt and subsequent resolidification. The throughput of ablation becomes maximal when machining at high pulse repetition rates and with a relatively low fluence, while at the same time the surface roughness is kept low.     

Ablation of polymers by focused EUV radiation from a table-top laser-produced plasma source

We have investigated ablation of polymers with radiation of 13.5 nm wavelength, using a table-top laser produced plasma source based on solid gold as target material. A Schwarzschild objective with Mo/Si multilayer coatings was adapted to the source, generating an EUV spot of 5 μm diameter with a maximum energy density of ∼1.3 J/cm². In combination with a Zirconium transmission filter, radiation of high spectral purity (2% bandwidth) can be provided on the irradiated spot. Ablation experiments were performed on PMMA, PTFE and PC. Ablation rates were determined for varying fluences using atomic force microscopy and white light interferometry. The slopes of these curves are discussed with respect to the chemical structure of the polymers. Additionally, the ablation behavior in terms of effective penetration depths, threshold fluences and incubation effects is compared to literature data for higher UV wavelength.     

Impact of the lasr wavelength and fluence on the ablation rate of aluminium

The dependence of the ablation rate of aluminium on the fluence of nanosecond laser pulses with wavelengths of 532 nm and respectively 1064 nm is investigated in atmospheric air. The fluence of the pulses is varied by changing the diameter of the irradiated area at the target surface, and the wavelength is varied by using the fundamental and the second harmonic of a Q-switched Nd-YAG laser system. The results indicate an approximately logarithmic increase of the ablation rate with the fluence for ablation rates smaller than ∼6 μm/pulse at 532 nm, and 0.3 μm/pulse at 1064 nm wavelength. The significantly smaller ablation rate at 1064 nm is due to the small optical absorptivity, the strong oxidation of the aluminium target, and to the strong attenuation of the pulses into the plasma plume at this wavelength. A jump of the ablation rate is observed at the fluence threshold value, which is ∼50 J/cm² for the second harmonic, and ∼15 J/cm² for the fundamental pulses. Further increasing the fluence leads to a steep increase of the ablation rate at both wavelengths, the increase of the ablation rate being approximately exponential in the case of visible pulses. The jump of the ablation rate at the threshold fluence value is due to the transition from a normal vaporization regime to a phase explosion regime, and to the change of the dimensionality of the hydrodynamics of the plasma-plume.