A low-noise SIS receiver measured from 480 GHz to 650 GHz using Nb junctions with integrated RF tuning circuits

A heterodyne receiver using an SIS waveguide mixer with two mechanical tuners has been characterized from 480 GHz to 650 GHz. The mixer uses either a single 0.5 × 0.5 µm² Nb/AlO_x/Nb SIS tunnel junction or a series array of two 1 µm² Nb tunnel junctions. These junctions have a high current density, in the range 8 – 13 kA/cm². Superconductive RF circuits are employed to tune the junction capacitance. DSB receiver noise temperatures as low as 200 ± 17 K at 540 GHz, 271 K ± 22 K at 572 GHz and 362 ± 33 K at 626 GHz have been obtained with the single SIS junctions. The series arrays gave DSB receiver noise temperatures as low as 328 ± 26 K at 490 GHz and 336 ± 25 K at 545 GHz. A comparison of the performances of series arrays and single junctions is presented. In addition, negative differential resistance has been observed in the DC I–V curve near 490, 545 and 570 GHz. Correlations between the frequencies for minimum noise temperature, negative differential resistance, and tuning circuit resonances are found. A detailed model to calculate the properties of the tuning circuits is discussed, and the junction capacitance as well as the London penetration depth of niobium are determined by fitting the model to the measured circuit resonances.     

100 GHz mixer vertically integrated (stacked) SIS junction array

A Vertically Integrated Array (stacked array) of single windowSIS junctions (VIA SIS), based on a stacked five layer structure of Nb-AlO_x-Nb-AlO_x-Nb, has been fabricated and tested in a quasi optical mixer configuration at 106 GHz. This particular VIA SIS design has two stacked junctions fabricated by standard tri-layer process employing photolithography, reactive ion and wet etching processes. A simple expression for calculating the specific capacitance of single and arrayed SIS junctions is suggested. Due to the absence of interconnection leads between the individual junctions and reduced overall capacitance, compared to a single SIS junction, has the VIA SIS good future prospects for use in submillimeter wave SIS mixers The VIA SIS may be regarded as a lumped rather than a distributed structure at least up to the gap frequency at 730 GHz for Nb. DC-IV measurements show high quality of the Individual SIS junctions and good reproducibility of the array parameters over the substrate area. The first VIA SIS mixer experiments yielded a receiver noise temperature of 95 K (DSB) at a LO frequency of 106 GHz.     

A Tuning Circuit with Two Half-Wave Distributed Junctions for All-NbN SIS Mixers

A novel broadband tuning circuit composed of two low-current-density half-wave NbN/MgO/NbN tunnel junctions connected by a half-wave NbN/MgO/NbN microstrip line has been successfully tested in a quasi-optical mixer at frequencies above 700 GHz. The circuit had a designed center frequency of 870 GHz, was integrated in a center-fed twin-slot antenna, and was fed via a quarter-wave impedance transformer. Heterodyne measurments showed double-side-band receiver noise temperatures equivalent to 6-9 quanta from 675 to 810 GHz for a mixer with a current density of 6.7 kA/cm². The RF bandwidth was broader than that of a conventional mixer using a full-wave junction with the same current density.     

Wide-band low noise MM-wave SIS mixers with a single tuning element

Several SIS quasiparticle mixers have been designed and tested for the frequency range from 80 to 115 GHz. The sliding backshort is the only adjustable RF tuning element. The RF filter reactance is used as a fixed RF matching element. A mixer which uses a single 2×2 m² Pb-alloy junction in a quarter-height waveguide mount has a coupled conversion gain of G_M(DSB)=2.6±0.5 dB with an associated noise temperature of T_M(DSB)=16.4±1.8 K at the best DSB operation point. The receiver noise temperature T_R(DSB) is 27.5±0.8 K for the mixer test apparatus. This mixer provides a SSB receiver noise temperature below 50 K over the frequency range from 91 to 96 GHz, the minimum being T_R(SSB)=44±4 K. Another mixer with an array of five 5×5 m² junctions in series in a full-height wave-guide mount has much lower noise temperature T_M(DSB)=6.6±1.6 K, but less gain G_M(DSB)=–5.1±0.5 dB.Contribution of the U.S. Government, not subject to copyright     

A 275–370 GHz Receiver Employing Novel Probe Structure

We present the results of the development of a 275–370 GHz, fixed-tuned double sideband (DSB) receiver based on superconductor-insulator-superconductor (SIS) junction mixer. The mixer block uses a full height rectangular waveguide and employs a novel radial-like probe structure with integrated bias-T. The measured uncorrected receiver noise temperature is 30–50 K corresponding to about 2–3 quantum noise across the full frequency band with an IF from 3.8 to 7.6 GHz. The mixer is to be used on the Atacama Pathfinder EXperiment (APEX) submillimeter telescope in Chile.     

Noise and thermal properties of a submillimeter mixer with the SINS tunnel junction

In this work we present for the first time a low-noise submillimeter receiver with a mixer using Superconductor-Insulator-Normal metal-Superconductor (SINS) junctions. Junctions containing a normal metal layer may be free of the Josephson current and of the related perturbations of mixer operation specific for the standard SIS mixers. This SINS mixer quality is important for the application in the multibeam submillimeter receiver. The SINS mixer stability of operation and independence on the magnetic field have been confirmed in our experiment. Minimum SINS receiver noise in the 290 – 330 GHz band is about 135 K when the junction R_NC is about 30. Noise, conversion gain and thermal properties of the SINS mixer have been studied and compared with the SIS mixers. The limit of SINS mixer operation improvement is discussed at the end of the work.     

Low noise 80–115 GHz quasiparticle mixer with small Nb/Al-Oxide/Nb tunnel junctions

Millimeter-wave characterization of a heterodyne receiver using (2 m²) Nb/Al-Ox/Nb Superconducting-Insulator-Superconducting (SIS) junctions arrays is reported. The fabrication of the Nb/Al-Ox/Nb SIS junction arrays as a heterodyne mixer is described. The leakage current of these junctions is below 2A at 4.2K and unmeasurable at 2.5K. The receiver gave a noise temperature Double Side Band (DSB) between 63K and 187K over the frequency range 80 to 115 GHz at the first conversion peak. The results are comparable to those obtained with SIS receivers using well researched lead junctions. Contrary to the lead junctions, our mixer using all Nb junctions have proven remarkably stable with respect to thermal cycling, characteristics which are required for space applications. To our knowledge, this is the most reliable low noise receiver operating in this frequency range.     

A 650-GHz Band SIS Receiver for Balloon-Borne Limb-Emission Sounder

A superconducting low-noise receiver has been developed for atmospheric observations in the 650-GHz band. A waveguide-type tunerless mixer mount was designed based on one for the 200-GHz band. Two niobium SIS (superconductor-insulator-superconductor) junctions were connected by a tuning inductance to cancel the junction capacitance. We designed the R_nC_j product to be 8 and the current density to be 5.5 kA/cm². The measured receiver noise temperature in DSB was 126-259 K in the frequency range of 618-660 GHz at an IF of 5.2 GHz, and that in the IF band (5-7 GHz) was 126-167 K at 621 GHz. Direct detection measurements using a Fourier transform spectrometer (FTS) showed the frequency response of the SIS mixer to be in the range of about 500-700 GHz. The fractional bandwidth was about 14%. The SIS receiver will be installed in a balloon-borne limb-emission sounder that will be launched from Sanriku Balloon Center in Japan.     

A Low-Noise 230 GHz SIS Receiver for Radio Astronomy Employing Untuned Nb/AlOx/Nb Tunnel Junctions

A heterodyne receiver based on a 1/3 reduced height rectangular waveguide SIS mixer with two mechanical tuners has been built for astronomical observations of molecular transitions in the 230 GHz frequency band. The mixer used an untuned array (R_nC_j3, R_n70 ) of four Nb/AIOx/Nb tunnel junctions in series as a nonlinear mixing element. A reasonable balance between the input and output coupling efficiencies has been obtained by choosing the junction number N=4. The receiver exhibits DSB (Double Side Band) noise temperature around 50 K over a frequency range of more than 10 GHz centered at 230 GHz. The lowest system noise temperature of 38 K has been recorded at 232.5 GHz. Mainly by adjusting the subwaveguide backshort, the SSB (Single Side Band) operation with image rejection of 15 dB is obtained with the noise temperature as low as 50 K. In addition, the noise contribution from each receiver component has been studied further. The minimum SIS mixer noise temperature is estimated as 15 K, pretty close to the quantum limit v/k11 K at 230 GHz. It is believed that the receiver noise temperatures presented are the lowest yet reported for a 230 GHz receiver using untuned junctions.     

A 691 GHz sis receiver for radio astronomy

We report the development of a low noise heterodyne receiver optimized for astronomical observations in the 650 GHz atmospheric window, and specifically for the CO(J=65) line at 691.5 GHz. The system is based on an open structure SIS heterodyne mixer pumped by a continuously tunable solid state oscillator. A niobium SIS junction double array is placed at the end of an integrated V-Antenna. For broad band impedance matching a combination of microstrip impedance transformer and radial stub was used. Receiver noise temperatures of 550 K DSB at 684 GHz were achieved at a 1.8 K physical temperature. The performance improved substantially when decreasing the temperature from 4.2 to 1.8 K. Comparison of model calculations and Fourier transform direct detection measurements of the tuning structure implies that this effect is likely due to the coincidence of operational frequency and the gap frequency of the niobium.     

345 GHZ PROTOTYPE SIS MIXER WITH INTEGRATED MMIC LNA

We report on heterodyne measurements at submillimeter wavelengths using a receiver with a Superconductor-Insulator-Superconductor (SIS) mixer device and a Microwave Monolithic Integrated Circuit (MMIC) cryogenic low noise amplifier (LNA) module integrated into the same block. The mixer characterization presented in this work demonstrates the feasibility of operating a MMIC LNA in close proximity to the SIS device without penalty in mixer performance due to heating effects. Verification of this functionality is crucial for the ongoing development of SuperCam, a 64-pixel focal plane array receiver consisting of eight, 1 × 8 integrated mixer/LNA modules. The test setup included a mixer block modified to accept a MMIC amplifier. Our tests show that the LNA can be operated over a broad range of V_drain voltages from 0.40–1.40 V, corresponding to dissipative powers of 2.6–29 mW. We observe no significant effect on the measured uncorrected receiver noise temperatures in the 345 GHz band.     

A 40 GHz band SIS receiver using Nb/Al?AlOx/Nb array junctions

A 40 GHz band SIS mixer receiver has been built using Nb/Al–AlOx/Nb array junctions and a 4.3 K closed cycle helium refrigerator. The minimum conversion loss of the mixer is 2±1 dB and the single sideband receiver noise temperature (T_RX (SSB)) is as low as 110±10 K at 36 GHz. T_RX (SSB) is almost constant in the IF bandwidth of 600 MHz. The mixer saturation level is as high as 15 nW, which is comparable to the injected LO power.Nobeyama Radio Observatory (NRO), a branch of the Tokyo Astronomical Observatory, University of Tokyo, is a cosmic radio observing facility open for outside users.     

A Multibeam SIS Mixer Module for a Focal Plane Array Receiver

The integration of many receiver units into a receiver array is a common method of improvement of imaging systems. This approach, well known in the mm band for Schottky mixer arrays, has not so far been developed for Superconductor - Insulator - Superconductor (SIS) junction mixers, which give the best sensitivity in the short mm wave range and in the submm range.We demonstrate for the first time a practical low noise multibeam receiver module using SIS mixer technology. The basis for the integration of several SIS mixers with a common local oscillator source is given by the saturation of the SIS receiver noise dependence upon local oscillator power. The module comprises three identical SIS mixers integrated with a common local oscillator, coupled through a three branch waveguide directional coupler. The multibeam module has been developed for a focal plane array receiver of the 30 meter radio telescope of the Institut de Radioastronomie Millimétrique (IRAM).     

A Fixed Tuned Low Noise 600-700 GHz SIS Receiver

We have designed and fabricated a fixed tuned low noise 600-700 GHz SIS mixer. Twin junctions connected in parallel was employed in the mixer design. A short microstrip tuning structure was used to minimize the RF signal loss at frequency above the energy gap. A receiver noise temperature below 200 K (without any loss correction) in the frequency range of 630 to 660 GHz was recorded. The lowest noise temperature of the receiver was 181 K (without any loss correction) at 656 GHz.     

180–425 GHz low noise SIS waveguide receivers employing tuned Nb/AIOx/Nb tunnel junctions

We report recent results on a 20% reduced height 270–425 GHz SIS waveguide receiver employing a 0.49 µm² Nb/AlO _x /Nb tunnel junction. A 50% operating bandwidth is achieved by using a RF compensated junction mounted in a two-tuner reduced height waveguide mixer block. The junction uses an end-loaded tuning stub with two quarter-wave transformer sections. We demonstrate that the receiver can be tuned to give 0–2 dB of conversion gain and 50–80% quantum efficiency over parts of it's operating range. The measured instantaneous bandwidth of the receiver is 25 GHz which ensures virtually perfect double sideband mixer response. Best noise temperatures are typically obtained with a mixer conversion loss of 0.5 to 1.5 dB giving uncorrected receiver and mixer noise temperatures of 50K and 42K respectively at 300 and 400 GHz. The measured double sideband receiver noise temperature is less than 100K from 270 GHz to 425 GHz with a best value of 48K at 376 GHz, within a factor of five of the quantum limit. The 270–425 GHz receiver has a full 1 GHz IF passband and has been successfully installed at the Caltech Submillimeter Observatory in Hawaii. Preliminary tests of a similar junction design in a full height 230 GHz mixer block indicate large conversion gain and receiver noise temperatures below 50K DSB from 200–300 GHz. Best operation is again achieved with the mixer tuned for 0.5–1.5 dB conversion loss which at 258 GHz resulted in receiver and mixer noise temperature of 34K and 27K respectively.     

A 100-GHz-band heterodyne sis receiver for the trao telescope

A 100-GHz-band Superconductor-Insulator-Superconductor (SIS) receiver has been developed for radio astronomy. The mixer used in this receiver has no mechanical tuning elements, such as a backshort or an E-plane tuner. The SIS junction consists of an array of four Nb/Al-AIOx/Nb junctions in series. The quasi-optic system for this receiver has been designed by frequency-independent matching method. The average DSB receiver noise temperature measured in the frequency range from 85 to 115 GHz is 40 K. The receiver is being successfully operated at the Taeduk Radio Astronomy Observatory in Korea.     

Determination of the spectral response of sis-junctions by a direct detection measurement

We present a simple method to determine the spectral response of an SIS detector in the millimeter and submillimeter wavelength range from its current response to a chopped cold-load. This direct detection response is also a good indicator of quantum efficiency and mixer noise temperature when using the SIS junction in heterodyne mode. A simple experimental setup without local oscillator, cryogenic IF-amplifier or any quasioptical interferometer allows a quick diagnosis of integrated planar impedance matching structures.     

A Low Noise NbTiN-Based 850 GHz SIS Receiver for the Caltech Submillimeter Observatory

We have developed a niobium titanium nitride (NbTiN) based superconductor-insulator-superconductor (SIS) receiver to cover the 350 micron atmospheric window. This frequency band lies entirely above the energy gap of niobium (700 GHz), a commonly used SIS superconductor. The instrument uses an open structure twin-slot SIS mixer that consists of two Nb/AlN/NbTiN tunnel junctions, NbTiN thin-film microstrip tuning elements, and a NbTiN ground plane. The optical configuration is very similar to the 850 GHz waveguide receiver that was installed at the Caltech Submillimeter Observatory (CSO) in 1997. To minimize front-end loss, we employed reflecting optics and a cooled beamsplitter at 4 K. The instrument has an uncorrected receiver noise temperature of 205K DSB at 800 GHz and 410K DSB at 900 GHz. The degradation in receiver sensitivity with frequency is primarily due to an increase in the mixer conversion loss, which is attributed to the mismatch between the SIS junction and the twin-slot antenna impedance. The overall system performance has been confirmed through its use at the telescope to detect a wealth of new spectroscopic lines.     

Open structure log-periodic SIS receivers at 180 and 305 GHz

Two open structure heterodyne receivers have been designed and tested at 180 and 305 GHz. The RF signal is coupled via a seven teeth log-periodic planar antenna to the mixer. The beam efficiency of the antenna is 65 %. The coupling efficiency to the fundamental gaussian mode is higher than 90%. The mixer incorporates a series array of two SIS Nb-Al/AlO_x-Nb junctions. Photolithographical techniques have been employed to fabricate the antennas and the junctions. Double side band noise receiver temperatures of 95 K at 190 GHz and 160 K at 305 GHz have been measured.     

Simple 1 MM Receivers with a Fixed Tuned Double Sideband SIS Mixer and a Wideband INP MMIC Amplifier

We report on techniques to broaden the intermediate frequency (IF) bandwidth of the BerkeleyIllinoisMaryland Array (BIMA) 1mm SuperconductorInsulatorSuperconductor (SIS) heterodyne receivers by combining fixed tuned Double Side Band (DSB) SIS mixers and wideband Monolithic Microwave Integrated Circuit (MMIC) IF amplifiers. To obtain the flattest receiver gain across the IF band we tested three schemes for keeping the mixer and amplifier as electrically close as possible. In Receiver I, we connected separate mixer and MMIC modules by a 1 stainless steel SMA elbow. In Receiver II, we integrated mixer and MMIC into a modified BIMA mixer module. In Receiver III, we devised a thermally split block in which mixer and MMIC can be maintained at different temperatures–in this receiver module the mixer at 4 K sees very little of the 10–20 mW heat load of the biased MMIC at 10 K. The best average receiver noise we achieved by combining SIS mixer and MMIC amplifier is 45 50 K DSB for _LO = 215–240 GHz and below 80 K DSB for _LO = 205 270 GHz. Over an IF frequency band of 1 – 4 GHz we have demonstrated receiver DSB noise temperatures of 40 – 60 K. Of the three receiver schemes, we feel Receiver III shows the most promise for continued development.