杂质对溶胶-凝胶SiO2薄膜激光损伤的影响

 采用溶胶-凝胶法制备了含有吸收性杂质和非吸收性杂质的SiO₂增透膜,采用波长为1 064 nm的激光对其进行了小光斑激光预处理,对比研究了预处理前后的激光损伤差异,研究表明：激光预处理对于洁净的SiO₂薄膜影响不大;含10 μm SiO₂颗粒杂质的样品微透镜效应很明显,容易成为损伤起始的种子,激光预处理后情况有所改善;含有CeO₂颗粒杂质的样品表现出了很强的吸收性质,损伤阈值降低到不足洁净样品的一半。所有样品激光预处理后损伤形貌未发生变化,透光率峰值均有约50 nm的蓝移。     

ZrO_2/SiO_2溶胶-凝胶薄膜膜层间的渗透行为

分别以丙醇锆和正硅酸乙酯为原料,采用溶胶-凝胶工艺制备了性能稳定的ZrO2和SiO2溶胶。用旋转镀膜法在K9玻璃上分别制备了单层SiO2薄膜、单层ZrO2薄膜、ZrO2/SiO2双层膜和SiO2/ZrO2双层膜。采用原子力显微镜观察了薄膜的表面形貌,用椭偏仪测量薄膜的厚度与折射率,用紫外-可见光分光光度计测量了薄膜的透射率。对薄膜的透射光谱和椭偏仪模拟的数据进行分析,发现SiO2/ZrO2双层膜之间的渗透十分明显,而ZrO2/SiO2双层膜之间几乎不发生渗透。利用TFCalc模系设计软件,采用三层膜模型对薄膜的透射率进行模拟,得出的透射曲线与用紫外-可见光分光光度计测量的透射曲线十分符合。     

溶胶-凝胶ZrO_2/SiO_2薄膜的激光损伤研究

采用溶胶-凝胶工艺分别制备了SiO2和ZrO2单层薄膜、ZrO2/SiO2双层膜以及ZrO2/SiO2多层高反膜。用输出波长为1064nm、脉宽为6.3ns的YAG激光器对薄膜进行了激光损伤实验。观察了薄膜经强激光辐照后的损伤情况,讨论了薄膜的激光损伤行为,并从理论上分析了产生这些损伤的原因,为进一步镀制高质量的ZrO2/SiO2多层高反膜提供了依据。     

HfO_2/SiO_2高反射膜的缺陷及其激光损伤

用原子力、Normaski和扫描电子显微镜等分析仪器 ,对高损伤阈值薄膜常采用的 Hf O2 /Si O2 薄膜进行了表面显微图象研究 ,分析了薄膜常见的表面缺陷 ,如节瘤 ,孔洞和划痕等。薄膜表面缺陷的激光损伤实验表明 ,不同缺陷的抗激光损伤能力大不相同 ,节瘤缺陷最低 ,约为 1 5 J/ cm2 ,薄膜的损伤阈值主要由其决定 ,孔洞的激光损伤能力与节瘤相比较高 ,约为节瘤的 2～ 3倍。节瘤缺陷在低能量密度的激光损伤所形成的孔洞 ,与镀制过程中形成的孔洞形貌相似 ,激光再损伤能力也相似。低能量密度的激光把节瘤缺陷变为孔洞缺陷是激光预处理提高薄膜损伤阈值的原因之一     

Accumulation effect of SiO_2 protective layer on multi-shot laser-induced damage in high-reflectivity HfO_2/SiO_2 coatings

The accumulation effects in high-reflectivity(HR) HfO2/SiO2 coatings under laser irradiation are investigated.The HR HfO2/SiO2 coatings are prepared by electron beam evaporation at 1 064 nm.The laser-induced damage threshold(LIDT) are measured at 1 064 nm and at a pulse duration of 12 ns,in 1-on-1 and S-on-1 modes.Multi-shot LIDT is lower than single-shot LIDT.The laser-induced and native defects play an important role in the multi-shot mode.A correlative theory model based on critical conduction band electron density is constructed to elucidate the experimental phenomena.     

KrF Laser-induced Damage to ZrO_2/SiO_2 Coatings

ＫｒＦＬａｓｅｒ－ｉｎｄｕｃｅｄＤａｍａｇｅｔｏＺｒＯ_２／ＳｉＯ_２Ｃｏａｔｉｎｇｓ￥ＷＡＮＧＮａｉｙａｎ；ＧＡＯＨｕａｉｌｉｎ（ＣｈｉｎａＩｎｓｔｉｔｕｔｅｏｆＡｔｏｍｉｃＥｎｅｒｇｙ，Ｐ．Ｏ．Ｂｏｘ２７５－７，Ｂｅｊｉｊｎｇ１０２４１３，Ｃｈｉｎ...     

高抗激光损伤阈值介孔SiO2 减反射膜

 用P123作模板剂,通过正硅酸乙酯的水解缩聚和溶剂蒸发自组装过程在K9玻璃上制备介孔SiO₂膜。应用FT-IR,XRD,N₂ 吸附-脱附,AFM和UV-Vis表征手段研究了薄膜的介孔结构和光学性能,并使用“R-on-1”模式,以Nd:YAG脉冲激光（9.2 ns, 1 064 nm）测试了薄膜的激光损伤阈值。结果表明:所镀制单层介孔SiO₂膜具有规整的2D p6 mm长周期结构,为SBA-15型,膜层表面比较平整（均方根粗糙度为2.923 nm）,在1 064 nm处的透过率为99.5%, 换算为激光脉宽为1 ns时,膜层的激光损伤阈值为21.6 J/cm²,显示出了较好的减反性能和抗激光损伤性能。     

Effect of standing-wave field distribution on femosecond laser-induced damage of HfO_2/SiO_2 mirror coating

Single-pulse and multi-pulse damage behaviors of "standard"(with λ/4 stack structure) and "modified"(with reduced standing-wave field) HfO2/SiO2 mirror coatings are investigated using a commercial 50-fs,800-nm Ti:sapphire laser system.Precise morphologies of damaged sites display strikingly different features when the samples are subjected to various number of incident pulses,which are explained reasonably by the standing-wave field distribution within the coatings.Meanwhile,the single-pulse laser-induced damage threshold of the "standard" mirror is improved by about 14% while suppressing the normalized electric field intensity at the outmost interface of the HfO2 and SiO2 layers by 37%.To discuss the damage mechanism,a theoretical model based on photoionization,avalanche ionization,and decays of electrons is adopted to simulate the evolution curves of the conduction-band electron density during pulse duration.     

单层SiO2物理膜与化学膜激光损伤机理的对比研究

采用离子束溅射沉积技术和溶胶-凝胶技术在K9基片上镀制了厚度相近的SiO2单层介质膜,用表面热透镜技术对两类膜层分别进行了热吸收及实时动态热畸变实验测试,结合散射光阈值测试及实验前后膜层的显微观测,对相同基底、相同膜层材料而采用不同方法镀制的光学膜层,发现化学膜的强激光损伤阈值远高于相应物理膜;从热力学响应及膜层特性差异的角度揭示了化学膜层的强激光损伤阈值远高于相应物理膜层的微观机理,即物理膜具有高吸收下的致密膜层快传导的基底热冲击效应,而化学膜则有低吸收下的疏松空隙填充慢传导的延缓效应,大量的实验数据及现象都证实了这一结论.     

单层SiO2物理膜与化学膜激光损伤机理的对比研究

采用离子束溅射沉积技术和溶胶-凝胶技术在K9基片上镀制了厚度相近的SiO₂单层介质膜，用表面热透镜技术对两类膜层分别进行了热吸收及实时动态热畸变实验测试，结合散射光阈值测试及实验前后膜层的显微观测，对相同基底、相同膜层材料而采用不同方法镀制的光学膜层，发现化学膜的强激光损伤阈值远高于相应物理膜；从热力学响应及膜层特性差异的角度揭示了化学膜层的强激光损伤阈值远高于相应物理膜层的微观机理，即物理膜具有高吸收下的致密膜层快传导的基底热冲击效应，而化学膜则有低吸收下的疏松空隙填充慢传导的延缓效应，大量的实验数据及现象都证实了这一结论. 关键词： 强激光辐照损伤 损伤形貌 热冲击 热吸收     

Femtosecond laser-induced damage of gold films

Single- and multi-shot ablation thresholds of gold films in the thickness range of 31-1400 nm were determined employing a Ti:sapphire laser delivering pulses of 28 fs duration, 793 nm center wavelength at 1 kHz repetition rate. The gold layers were deposited on BK7 glass by an electron beam evaporation process and characterized by atomic force microscopy and ellipsometry. A linear dependence of the ablation threshold fluence F_th on the layer thickness d was found for d ≤ 180 nm. If a film thickness of about 180 nm was reached, the damage threshold remained constant at its bulk value. For different numbers of pulses per spot (N-on-1), bulk damage thresholds of ∼0.7 J cm⁻² (1-on-1), 0.5 J cm⁻² (10-on-1), 0.4 J cm⁻² (100-on-1), 0.25 J cm⁻² (1000-on-1), and 0.2 J cm⁻² (10000-on-1) were obtained experimentally indicating an incubation behavior. A characteristic layer thickness of L_c ≈ 180 nm can be defined which is a measure for the heat penetration depth within the electron gas before electron-phonon relaxation occurs. L_c is by more than an order of magnitude larger than the optical absorption length of α⁻¹ ≈ 12 nm at 793 nm wavelength.     

Multiscale analysis of single- and multiple-pulse laser-induced damages in HfO_2/SiO_2 multilayer dielectric films at 532 nm

Nanosecond single- and multiple-pulse laser damage studies on Hf O2∕Si O2high-reflection(HR) coatings are performed at 532 nm. For single-pulse irradiation, the damage is attributed to the defects and the electric intensity distribution in the multilayer thin films. When the defect density in the irradiated area is high, delamination is observed. Other than the 1064 nm laser damage, the plasma scalding of the 532 nm laser damage is not pits-centered for normal incidence, and the size of the plasma scalding has no relation to the defect density and position, but increases with the laser fluence. For multiple-pulse irradiations, some damage sites show deeper precursors than those from the single-shot irradiation due to the accumulation effects. The cumulative laserinduced damages behave as pits without the presence of plasma scalding, which is unaffected by the laser fluence and shot numbers. The damage morphologies and depth information both confirm the fatigue effect of a Hf O2∕Si O2 HR coating under 532 nm laser irradiation.     

杂质对溶胶-凝胶SiO2薄膜激光损伤的影响

采用溶胶-凝胶法制备了含有吸收性杂质和非吸收性杂质的SiO2增透膜,采用波长为1 064 nm的激光对其进行了小光斑激光预处理,对比研究了预处理前后的激光损伤差异,研究表明：激光预处理对于洁净的SiO2薄膜影响不大;含10 μm SiO2颗粒杂质的样品微透镜效应很明显,容易成为损伤起始的种子,激光预处理后情况有所改善;含有CeO2颗粒杂质的样品表现出了很强的吸收性质,损伤阈值降低到不足洁净样品的一半。所有样品激光预处理后损伤形貌未发生变化,透光率峰值均有约50 nm的蓝移。     

248 nm高反膜抗激光损伤性能

用电子束蒸发法在熔融石英基底上沉积了适用于248 nm的HfO2/SiO2高反膜,为提高其抗激光损伤能力,设计并制备了两种保护层,一种是在常规高反膜系的基础上镀制二分之一波长厚度的SiO2保护层,另一种是用Al2O3/MgF2做保护层。测试了3种高反膜样品的激光损伤情况,通过损伤形貌的变化分析了两种保护层使抗激光损伤能力提高的原因以及存在的问题。     

248 nm高反膜抗激光损伤性能

用电子束蒸发法在熔融石英基底上沉积了适用于248nm的HfO2/SiO2高反膜,为提高其抗激光损伤能力,设计并制备了两种保护层,一种是在常规高反膜系的基础上镀制二分之一波长厚度的SiO2保护层,另一种是用Al2O3/MgF2做保护层。测试了3种高反膜样品的激光损伤情况,通过损伤形貌的变化分析了两种保护层使抗激光损伤能力提高的原因以及存在的问题。     

Influence of substoichiometer on the laser-induced damage characters of HfO2 thin films

HfO₂ is one of the most important high refractive index materials for depositing high power optical mirrors. In this research, HfO₂ thin films were prepared by dual-ion beam reactive sputtering method, and the laser-induced damage thresholds (LIDT) of the sample were measured in 1-on-1 mode for laser with 1064 nm wavelength. The results indicate that the LIDT of the as-grown sample is only 3.96 J/cm², but it is increased to 8.98 J/cm² after annealing under temperature of 200 °C in atmosphere. By measuring the laser weak absorption and SIMS of the samples, we deduced that substoichiometer is the main reason for the low LIDT of the as-grown sample, and the experiment results were well explained with the theory of electronic-avalanche ionization.     

Effects of deposition parameters on laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited on BK7 substrates by e-beam evaporation with different deposition parameters such as substrate temperature (323-623 K), oxygen pressure (0.5-3.0×10⁻² Pa) and deposition rate (0.2-0.5 nm/s). Absorption, scattering and chemical composition were investigated by surface thermal lensing (STL) technique, total integrated scattering (TIS) measurement and X-ray photoelectron spectroscopy (XPS), respectively. The laser-induced damage threshold (LIDT) was assessed using pulsed Nd:YAG 1064 nm laser at a pulse length of 12 ns. The results showed that optical properties, absorption and LIDT were influenced by the deposition parameters and annealing. However, scattering was little correlated with the deposition parameters. On the whole, the LIDT increased with increasing substrate temperature and oxygen pressure, whereas it increased firstly and then decreased upon increasing deposition rate. After annealing at 673 K for 12 h, the LIDT of films improved significantly. The dependence of possible damage mechanism on deposition parameters was discussed.     

Stress, absorptance and laser-induced damage threshold properties of 355-nm HR coatings

A number of 355-nm Al₂O₃/MgF₂ high-reflectance (HR) coatings were prepared by electron-beam evaporation. The influences of the number of coating layers and deposition temperature on the 355-nm Al₂O₃/MgF₂ HR coatings were investigated. The stress was measured by viewing the substrate deformation before and after coating deposition using an optical interferometer. The laser-induced damage threshold (LIDT) of the samples was measured by a 355-nm Nd:YAG laser with a pulse width of 8 ns. Transmittance and reflectance of the samples were measured by a Lambda 900 spectrometer. It was found that absorptance was the main reason to result in a low LIDT of 355-nm Al₂O₃/MgF₂ HR coatings. The stress in Al₂O₃/MgF₂ HR coatings played an unimportant role in the LIDT, although MgF₂ is known to have high tensile stress.     

Preparation of sol-gel ZrO2-SiO2 highly reflective multilayer films and laser-induced damage threshold characteristic

Sol-gel (ZrO₂/SiO₂)¹² ZrO₂ films were prepared by spin coating method. The reflectivity spectrum of the films was measured with a Lambda 900 spectrometer. In order to investigate laser-induced damage threshold (LIDT) characteristic of highly reflective films, one-layer ZrO₂ and SiO₂ films, two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were also prepared by spin coating method. LIDT of each film was measured. Damage morphology after laser irradiation was characterized by optical microscopy (Nikon E600K). The experimental results showed that the reflectivity of (ZrO₂/SiO₂)¹² ZrO₂ film at 1064 nm and 355 nm wavelength is 99.7%. The LIDT results decreases as the number of layer of films increases. All the films have similar damage morphology. The experimental results are explained by the different temperature profiles of the films.     

Overcoat dependence of laser-induced damage threshold of 355 nm HR coatings

A series of HR coatings, with and without overcoat, were prepared by electron beam evaporation using the same deposition process. The laser-induced damage threshold (LIDT) was measured by a 355 nm Nd:YAG laser with a pulse width of 8 ns. Damage morphologies of samples were observed by Leica-DMRXE Microscope. The stress was measured by viewing the substrate deformation before and after coatings deposition using an optical interferometer. Reflectance of the samples was measured by Lambda 900 Spectrometer. The theoretical results of electric field distributions of the samples were calculate by thin film design software (TFCalc). It was found that SiO₂ overcoat had improved the LIDT greatly, while MgF₂ overcoat had little effect on the LIDT because of its high stress in the HR coatings. The damage morphologies were different among HR coatings with and without overcoats.