H2SO4处理的Nb2O5/γ -Al2O3催化剂表面酸性与催化性能研究

用Hammett指示剂法、红外光谱（IR）、示差扫描量热-热重法（DSC-TG）和微型催化反应装置等研究了H₂SO₄处理的负载型Nb₂O₅/γ-Al₂O₃催化剂表面酸性和催化异丁烯（IB）与异丁醛（IBA）反应生成2，5-二甲基-2，4-己二烯（DMHD）的催化性能。结果表明随所用H₂SO₄浓度增加，Nb₂O₅/γ-Al₂O₃催化剂表面酸性增强，B酸量增加，L酸量先增加后下降。经H₂SO₄处理的Nb₂O₅/γ-Al₂O₃催化剂的催化活性明显增加，但当H₂SO₄浓度超过0.05 mol·L^-1时催化活性又急剧下降，这可能是因为在H₂SO₄处理的催化剂表面形成的强酸中心上，产物分子进一步转化为积炭且封闭催化剂活性表面，导致催化活性下降。     

纳米固体超强酸SO42-/Fe2O3的制备及其催化合成乙酸乙酯

将Fe₂O₃纳米粉体经一定浓度的H₂SO₄浸泡活化后制成纳米固体超强酸SO₄^2-/Fe₂O₃,将其用于催化合成乙酸乙酯以考察其活性。利用均匀设计分析了超强酸制备过程及酯化反应过程中各因素的影响,研究结果表明较好的制备条件是:H₂SO₄浓度:2.5mol·L^-1;浸泡时间:1h;活化温度:167℃;活化时间:1h,此时获得的固体超强酸SO₄^2-/Fe₂O₃的粒径小于50nm。当催化剂用量为冰乙酸质量的5%,n(乙醇)∶n(冰乙酸)为3∶1,反应3.5h后乙酸的转化率高于80%。该催化剂经H₂SO₄溶液浸泡、活化再生后可重新使用,推断出其酸强度H₀<-14.5。     

Fe2O3填充碳纳米管作为锂离子电池负极材料的电化学性能

通过碳纳米管与硝酸铁水热反应和随后烧结处理合成了Fe₂O₃填充多壁碳纳米管，透射电子显微镜(TEM)和X-射线衍射(XRD)分析显示，Fe₂O₃多数填充入碳纳米管管腔内，在碳纳米管外壁极少发现有附着物，碳纳米管中Fe₂O₃颗粒具有γ-Fe₂O₃结构，这与水热法制备的的纺锤状Fe₂O₃(α-Fe₂O₃相)明显不同。这是因为硝酸将管壁及管端腐蚀，Fe³⁺由于毛细管作用进入管腔。文章初步研究了Fe₂O₃填充多壁碳纳米管、水热法合成的纳米Fe₂O₃颗粒和硝酸纯化的多壁碳纳米管的电化学嵌/脱锂性能。研究发现，Fe₂O₃填充多壁碳纳米管具有Fe₂O₃的高的放电容量和碳纳米管的低放电电位特征。由于碳纳米管的限定作用，缓解了碳纳米管空腔内γ-Fe₂O₃在反复锂嵌/脱过程中的结构应变，该复合材料表现出具有良好的循环稳定性。     

磁性固体超强酸SO42-/ZrO2-Al2O3-Fe3O4的制备与性能研究

利用化学共沉淀法将磁性基质与固体酸组装制备磁性纳米固体超强酸催化剂，利用XRD、Raman、TG-DSC、M?ssbauer、TEM、HRTEM等手段对样品性质进行表征。结果表明：磁性基质的引入赋予固体超强酸以超顺磁性；Fe₃O₄、Al₂O₃粒子弥散在ZrO₂基质中，烧结过程中阻碍了扩散传质的进行以及晶界移动，抑制了ZrO₂晶体生长，稳定了四方晶相(T-ZrO₂)；样品粒径分布集中，平均约为32 nm；HRTEM显示T-ZrO₂晶体生长取向于(101)方向，晶面间距d(101)=0.29 nm；Hammett指示剂法测得经600 ℃焙烧后产物的酸强度H_o＜-13.8，酸强度大于浓硫酸(H_o=-11.93)。以柠檬酸三丁酯的合成作为磁性固体超强酸SO₄^2-/ZrO₂-Al₂O₃-Fe₃O₄催化剂的探针反应，结果表明外磁场的引入提高了柠檬酸的转化率。     

表面缺陷α-Fe2O3(001)纳米片双活性位点类芬顿催化剂用于降解污染物

纯Fe₂O₃表面活性位点较少具有较低的催化活性限制了其在多相芬顿催化体系中的应用。通常采用元素掺杂、贵金属负载以及与其它化合物质复合等改性措施来提升催化活性,然而这些措施存在催化剂制备复杂,制备成本高以及催化剂的精细结构难以精准控制等问题。因此,本文提出在α-Fe₂O₃表面引入氧空位缺陷构筑双活性位点（Fe²⁺和氧空位）用于促进H₂O₂分解提高降解污染物降解效率。实验结果发现α-Fe₂O_3-x-330/H₂O₂体系具有较宽的pH使用范围（pH=2~10）。当pH=4时,罗丹明B的降解速率常数为0.834 h^-1,而且催化剂具有磁性,易回收重复使用。催化机理研究表明氧空位缺陷α-Fe₂O_3-x催化剂的氧空位和Fe²⁺两种活性位点均可促进H₂O₂分解,而且氧空位的引入有利于污染物在催化剂表面的吸附进一步提高催化性能。     

Cu/SO42-/La2O3-ZrO2-Al2O3催化剂的制备及其对C3H6选择还原NO的催化性能

以Al₂O₃为基质，添加ZrO₂和La₂O₃，制成La₂O₃-ZrO₂-Al₂O₃复合载体，然后采用SO₄^2-进行改性，再负载上Cu²⁺，制备了铜基SO₄^2-改性的复合载体催化剂(Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃)。考察了它在富氧条件下对丙烯选择还原NO的催化性能，并借助XRD、SEM、TG、Py-IR、NH₃-TPD、FTIR和TPR等方法研究了Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃的结构和性能的关系。结果表明，ZrO₂的加入主要有利于提高催化剂的低温活性；La₂O₃的加入则主要有利于提高催化剂的热稳定性和还原性能；SO₄^2-能够与Zr形成螯合双配位结构，大幅度促使催化剂表面酸量增加并且酸性增强；因此，有效地提高了Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃在富氧条件下对丙烯选择还原NO的催化活性和水热稳定性。在无水条件下，Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃能使NO的最大转化率高达84.3%，即使在275 ℃ 10%水蒸气存在的情况下，仍能使NO的转化率高达81.2%。     

[NH3(CH2)5NH3][Fe2{O3PC(CH3)(OH)(PO3H)}2]·2H2O:一个新的二膦酸亚铁化合物的合成、结构与性质研究

通过水热合成得到一个新的有机二膦酸亚铁化合物[NH₃(CH₂)₅NH₃][Fe₂^Ⅱ{O₃PC(CH₃)(OH)(PO₃H)}₂]·2H₂O,该化合物包含阴离子型共价双链[Fe₂^Ⅱ{O₃PC(CH相似文献   

Li+，Na+//SO42-，B4O72--H2O交互四元体系288 K介稳相平衡研究

采用等温蒸发法研究了四元体系Li⁺，Na⁺//SO₄^2-，B₄O₇^2--H₂O 288 K介稳相平衡及平衡液相物化性质(密度、电导率、折光率、粘度和pH值)，测定了该四元体系288 K条件下介稳平衡溶液溶解度及物化性质。根据实验数据绘制了相应的介稳相图及物化性质组成图。研究发现：该体系介稳平衡中有复盐Li₂SO₄·Na₂SO₄形成。其介稳相图中有3个共饱和点，7条单变量曲线，平衡固相为：Li₂SO₄·H₂O，Na₂SO₄，Li₂SO₄·Na₂SO₄，Li₂B₄O₇·3H₂O，Na₂B₄O₇·10H₂O。复盐Li₂SO₄·Na₂SO₄和一水硫酸锂(Li₂SO₄·H₂O)有较小的结晶区，而Li₂B₄O₇·3H₂O和Na₂B₄O₇·10H₂O有较大的结晶区；该四元体系介稳平衡条件下未发现Na₂SO₄·10H₂O的结晶区。     

Fe3O4@SiO2@mTiO2介孔多功能纳米复合颗粒的制备及载药能力

以溶剂热法制备氨基功能化的Fe₃O₄纳米颗粒为磁核,结合溶胶-凝胶法和模板法在其表面先后包覆上致密的SiO₂层和介孔TiO₂层,制备了磁性-发光-微波热转换性-介孔结构为一体的多功能核-壳结构纳米复合颗粒,并对其结构、性能及载药能力进行了研究。XRD分析表明:Fe₃O₄表面包覆上了无定形结构的SiO₂和TiO₂。TEM照片表明:所得的纳米复合颗粒具有明显的核壳结构和完美的球形,构成核的Fe₃O₄颗粒的尺寸在40~50 nm之间,Fe₃O₄@SiO₂@mTiO₂核壳结构纳米复合颗粒的尺寸为60~70 nm,壳层厚度约10 nm,并可观察到壳层中清晰的孔状结构。磁性、荧光光谱和微波热转换特性分析表明:该复合颗粒同时具有良好的发光性、磁性和微波热转换特性。N₂气吸附及药物负载率分析表明,该复合颗粒具有较高的比表面积(640 m²·g^-1)和介孔结构(孔径约2.8 nm)并且具有较高的药物负载率。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.