A new visible photoluminescence in the conducting Ta-Si-N nanocomposite thin films

The conventional visible photoluminescence (PL) behavior at room temperature (RT) is observed in the semiconducting or insulating nanostructured materials with large bandgaps. Here, we have demonstrated the visible-color PL behavior at RT of the conducting Ta-Si-N thin films nanocomposite using simple magnetron sputtering without any post annealing. X-ray diffraction, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) depth profile results evidence that the microstructure of conducting Ta-Si-N with a low resistivity of 220-375 μΩ cm exhibits (Ta_x,Si_y)N nanocrystalline grains embedded in an amorphous matrix, which can emit the distinct PL intensity from 390 to 750 nm wavelengths. No PL is detected in the coarse-grain polycrystalline films. Qin's extended quantum confinement/luminescence center model [G.G. Qin, Mater. Res. Bull. 33 (1998) 1857-1866] was adopted and modified to discuss the RT PL mechanism in the conducting Ta-Si-N films using three types of competitive photoexcitation/photoemission processes.     

Relationship between crystal morphology and photoluminescence in polynanocrystalline lead sulfide thin films

Thin films of lead sulfide (PbS) nanoparticles were grown on corning glass and Si(1 0 0) substrates by polyethylene glycol-assisted chemical bath deposition (CBD) method. This paper compares the morphology and the luminescence properties (PL) of the deposited thin films in the presence (or absence) of PEG300 and investigates the effect of deposition temperatures. Surface morphology and photoluminescence properties of samples were analyzed. The PL data show a blue-shift from the normal emission at ∼2900 nm in PbS bulk to ∼360 nm in nanoparticles of PbS thin films. Furthermore, the PL emission of the films obtained without the addition of PEG300 (type 1) was slightly shifted from that of the films obtained in presence of PEG300 (type 2) from ∼360 to ∼470 nm. The blue-shifting of the emission wavelengths from 2900 to ∼360 or 470 nm is attributed to quantum confinement of charge carriers in the restricted volume of nanoparticles, while the shift between the two types of PbS nanoparticles thin films is speculated to be due to an increase in the defect concentration. The blue-shift increased with increase of the deposition temperature, which suggests that there has been a relative depletion in particle sizes during the CBD of the films at higher temperatures. The PbS nanocrystalline thin films obtained in the presence of PEG300 at 60 °C exhibit a high blue luminescence.     

Gradients of topographical structure in thin polymer films

We report the fabrication of centimeter-long gradients of topography. Structured polymer thin films were made by spin-coating an immiscible poly(methyl methacrylate)/poly(2-vinylpyridine) (PMMA/P2VP) blend from a common solvent on a substrate presenting a surface-energy gradient. Due to the interplay between polymer-wetting of the substrate and polymer phase-separation, different morphologies were observed along the sample. Atomic force microscopy (AFM) revealed a gradual transition from a flat to a structured morphology as the surface energy of the substrate was reduced. The transition occurred for a well-defined range of surface energies. A selective solvent was used to remove one of the polymer phases, increasing the topographical contrast and providing insight into the different stages of the transition. Image analysis allowed a quantitative characterization of the structure gradient.     

Effect of solution concentrations on crystal structure,surface topographies and photoluminescence properties of ZnO thin films

Zinc oxide thin films were deposited on silicon substrates via hydrothermal method. Microstructures, surface topographies and optical properties of ZnO thin films were systematically investigated by X-ray diffraction, atomic force microscopy and fluorescence spectrophotometer. The mean grain size and surface roughness of the thin films decrease first and then increase with increasing the concentration of zinc nitrate hexahydrate. The photoluminescence spectra of ZnO thin films, excited by the 240, 320, 360, 380 and 400 nm excitation wavelength, were investigated in detail. Based on our analysis, it can be noted that mechanisms of the ultraviolet, violet and blue emissions are attributed to the transitions from the localized levels below the conduction band, zinc vacancy, interstitial zinc and extended interstitial zinc levels to the valance band, respectively. Blue–violet emissions of ZnO have great potential in light emitting and biological fluorescence labeling applications.     

Metal Enhanced Fluorescence Solution-based Sensing Platform 2: Fluorescent Core-Shell Ag@SiO<Subscript>2</Subscript> Nanoballs

In this Rapid Communication, we present the development of monodisperse core-shell (silver core-silica shell) nanoparticles with various shell thicknesses featuring a fluorophore, subsequently named Metal-Enhanced Fluorescence (MEF) nanoballs. MEF nanoballs consist of a ≈130 nm silver nanoparticle core, a silica shell with up to 35 nm thickness and fluorophores doped within the silica shell. Fluorescent nanobubbles where the silver core is removed by chemical etching are used as control samples to show the benefits of using silver nanoparticles, i.e, Metal-Enhanced Fluorescence. Finally, we demonstrate the broad potential biological applications of MEF nanoballs by employing near-infra red emitting probes (Rhodamine 800) within the silica shell, for potential applications in cellular imaging and solution-based sensing. Kadir Aslan, Meng Wu, Contributed equally     

Surface enhanced Raman scattering in organic thin films covered with silver, indium and magnesium

In situ resonant Raman spectroscopy was applied for the investigation of the interface formation between silver, indium and magnesium with polycrystalline organic semiconductor layers of 3,4,9,10-perylene tetra-carboxylic dianhydride (PTCDA). The spectral region of internal as well as external vibrational modes was recorded in order to achieve information related to the chemistry and the structure of the interface as well as to morphology of the metal layer. The experiments benefit from a strong enhancement of the internal mode scattering intensities which is induced by the rough morphology of deposited metals leading to surface enhanced Raman scattering (SERS). The external modes, on the other hand, are attenuated at different rates indicating that the diffusion of the metal atoms into the crystalline layers is highest for indium and lowest for magnesium.     

Tunability of the photoluminescence in porous silicon due to different polymer dielectric environments

In this report we demonstrate control over porous silicon (PSi) emission properties by changing the dielectric environment surrounding the silicon crystallites, as well as provide information on the effects of pore infiltration of PSi. This is achieved by making PSi–polymer nanocomposites by diffusing or polymerizing a range of varying dielectric constant polymers into the pores. The degree of modification in photoluminescence (PL) depends on the dielectric constant of the polymers. By increasing the dielectric constant of the environment surrounding the crystallites, a blue shift in PL as high as 222 meV has been observed. The blue shift is attributed to the high dielectric constant of the polymers relative to PSi, which causes a partial screening of the excitons allowing the excitonic levels to shift closer to the bandgap. The shift in excitonic levels increases when the dielectric constant of the polymer increases. PSi–polymer nanocomposites also exhibit an increase in PL intensity, which suggest that the inert infiltrated polymers are able to passivate existing nonradiative channels.     

Photoluminescence studies on nanostructured cadmium sulfide thin films prepared by chemical bath deposition method and annealed at different temperatures

Nanostructured cadmium sulfide (CdS) thin films have been prepared by chemical bath deposition (CBD) method and after post deposition annealing of the thin films at different temperatures, photoluminescence (PL) property has been studied. The effects of various photoexcitation wavelengths on the PL behaviour of different annealed films of CdS were studied by recording the PL spectra. The intensity of PL, the profile of the PL spectra and the effects of photoexcitation wavelength depend drastically on the temperature of the post deposition annealing of the thin films. The XRD patterns of the films show the presence of both the hexagonal and cubic phases (mixed phases). The emission peak arises from the surface defects of the CdS nanocrystalline thin films. Significant modification in the surface morphology of the CdS films upon annealing has been observed from the FESEM images. The morphology of the thin films is expected to influence the PL behaviour of the CdS thin films. The quantum size effect and size dependant PL have been observed.     

Proton radiation effects of conjugated polymer thin films

Polymeric-thin-film-based electronic and optoelectronic materials and devices are attractive for potential space and certain radiation-related applications due to their inherent features such as lightweight, flexible, biocompatible, etc. Proton radiation is a major form of ionizing radiation in space, particularly in the so-called inner Van Allen belt region where most near-earth satellites are orbiting, yet very few literature and data are available on proton radiation effects on conjugated polymer systems. In this report, the proton radiation effects on potential electronic/optoelectronic properties of several conjugated polymers and their composites are briefly evaluated. Specifically, UV–VIS absorption spectra of several conjugated polymers and/or their composite thin films were measured and compared right before and after the proton radiations at different dosages. The results revealed that proton radiation has very little or insignificant impact up to 800?rad on the optoelectronic properties of poly-3-hexyl-thiophene (P3HT), P3HT:PC₆₀BM blend, a light harvesting donor-bridge-acceptor (DBA) and a novel donor-bridge-fluorinated-acceptor (DBfA)-type block copolymer thin films.     

Tuning of surface properties of thin polymer films by electron beam treatment

The aim of our work was to understand the impact of electron treatment on polymer thin films, particularly on their surface properties as well as the possibilities and limitations to tune these properties. Two different polymers, polystyrene (PS) and poly-2-vinlypyridine (P2VP), were chosen to form thin polymer films by grafting of end-terminated linear polymer chains to a surface with sufficient grafting density, forming so called “polymer brushes”. We were able to identify the surface properties and specify ongoing physico-chemical changes after electron beam treatment by using zeta potential and contact angle measurements. By varying the absorbed dose it was possible to tune the surface properties over a wide range. The detailed knowledge about the latitude of functionalization of the tested polymers was a prerequisite for the creation of wettability gradients by electron beam treatment by adapting a special mask of known thickness and density. Hence, electron beam treatment opens an easy reproducible way to generate surface gradients in functionality.     

纳米粒子修饰硅胶整体柱的制备及其在柱表面增强拉曼光谱应用研究

通过溶胶-凝胶法以四甲氧基硅烷(TMOS)和甲基三甲氧基硅烷(MTMS)作为混合的前体,聚乙二醇(PEG)为致孔剂,制备了具有贯通孔道结构的双孔硅胶整体柱,采用3-巯基丙基三甲氧基硅烷(MTPMS)对硅胶整体柱表面进行巯基化修饰后,分别将金、 银纳米粒子组装在整体柱材料表面。 利用透射电子显微镜(TEM)、 紫外-可见吸收光谱(UV-Vis)、 扫描电子显微镜(SEM)对金、 银纳米粒子形貌、 吸收光谱及组装金、 银纳米粒子前后整体柱的形貌进行了表征。 以对巯基苯胺(PATP)为探针分子,分别采用波长为633和532 nm的激发光作为激发光源,研究金和银纳米粒子修饰的硅胶整体柱的在柱表面增强拉曼光谱(SERS)性能。 结果表明,该基底呈现出很强的SERS活性,结合整体柱的分离富集优势将在食品/环境领域现场痕量检测方面具有广泛的应用前景。     

Mechanism of gain narrowing in conjugated polymer thin films

Received: 19 January 1998     

Influence of polyethylene glycol-300 addition on nanostructured lead sulfide thin films properties

The concentration of polyethylene glycol-300 was found to play a crucial role in the formation of nanoparticles in PbS-chemical bath deposition process. We report here an endeavor to set up a relation between the variation of lead sulfide (PbS) nanocrystalline thin film properties, grown by (CBD) process at room temperature on corning glass and Si(100) substrates, with amount fluctuations of polyethylene glycol-300 in the solution. The transmittance of the films, for a fixed reaction time, increased up to ∼ 80% with the increase of % polyethylene glycol-300 in the solution, indicating the formation of very thin films due to the decrease of reaction rate with the increase of the concentration of polyethylene glycol-300. The optical band gaps were found to strongly rely on the composition of the bath deposition and increase with the increase of the polyethylene glycol-300 amount in the solution. Particle sizes between 2.8 and 8.7 nm were obtained by varying the % of polyethylene glycol-300 from 0.2 to 1.5. The concentration of polyethylene glycol-300 not only affects the reaction rate but also the morphology of the obtained films. PbS nanoparticles were found to be oriented preferentially along the < 200> plane. The absorption shifts towards short wavelength indicating a blue-shifting as a consequence of quantum confinement.     

Enhanced photo-induced hydrophilicity of the sol-gel-derived ZnO thin films by Na-doping

Na-doped ZnO thin films with different Na/Zn ratio were prepared by sol-gel method. The microstructure, chemical composition, surface morphology, and wettability of the thin films were investigated by X-ray diffraction, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy, and water contact angle apparatus. The relation of wettability and Na/Zn ratio has been studied in detail. The wetting behavior of the thin films can be reversibly switched from hydrophobic to hydrophilic, through alternation of UV illumination and dark storage (or thermal treatment). Photo-induced hydrophilicity of the thin films increases with increasing Na/Zn ratio up to 0.08 and then decreases. The mechanism can be attributed to surface nanostructure and the concentration of Na doping.     

Synthesis and time-resolved photoluminescence spectroscopy of capped CdS nanocrystals

Here, we report the synthesis of colloidal CdS nanoparticles by capping with starch, phenol and pyridine. We also study the photophysical properties of CdS nanoparticles by steady state and time-resolved photoluminescence spectroscopy. The experimental results show that the relaxation of the excited state of CdS nanoparticles is composed of two different components. Our analysis suggests that the fast and slow components decay times of these capped CdS nanocrystals are due to trapping of carriers in surface state and e–h radiative recombination processes, respectively.     

Reversible wettability of nanostructured ZnO thin films by sol-gel method

Nanostructured ZnO thin films were deposited on Si(1 1 1) and quartz substrate by sol-gel method. The thin films were annealed at 673 K, 873 K, and 1073 K for 60 min. Microstructure, surface topography, and water contact angle of the thin films have been measured by X-ray diffractometer, atomic force microscopy, and water contact angle apparatus. XRD results showed that the ZnO thin films are polycrystalline with hexagonal wurtzite structure. AFM studies revealed that rms roughness changes from 2.3 nm to 7.4 nm and the grain size grow up continuously with increasing annealing temperature. Wettability results indicated that hydrophobicity of the un-irradiated ZnO thin films enhances with annealing temperature increase. The hydrophobic ZnO surfaces could be reversibly switched to hydrophilic by alternation of UV illumination and dark storage (thermal treatment). By studying the magnitude and the contact angle reduction rate of the light-induced process, the contribution of surface roughness is discussed.     

Post-annealing influence on electrical properties and photoluminescence of B-N codoping ZnO thin films

B-N codoped ZnO (ZnO:(B,N)) films were grown on quartz substrate by radio-frequency (rf) magnetron sputtering. The influence of post-annealing ambient on electrical and optical properties of ZnO:(B,N) films were investigated using Hall and Photoluminescence (PL) measurement, respectively. Electrical properties studies indicate that both post-annealing ZnO:(B,N) showed p-type conduction. However, compared with ZnO:(B,N) annealed in oxygen, the ZnO:(B,N) annealed in vacuum have low resistivity and high concentration. The PL spectra indicate that two new emission bands located at 3.303 and 3.208 eV originate from the recombination of A⁰X and FA related to N acceptor for the annealed p-ZnO:(B,N) in vacuum, but of A⁰X, FA related to Zn vacancy for the annealed p-ZnO:(B,N) in oxygen. The mechanism of influence of post-annealing on the electrical and optical properties of the ZnO:(B,N) film is discussed in this work.     

退火对ZnO:Al薄膜光致发光性能的影响

 采用溶胶-凝胶工艺在石英衬底上制备ZnO:Al（AZO）薄膜,通过不同温度的退火处理,研究了退火对AZO薄膜结构和光致发光特性的影响。XRD图谱表明：所制备的薄膜具有c轴高度择优取向,随着退火温度的升高,(002)峰的强度逐渐增强,同时(002)峰的半高宽逐渐减小,表明晶粒在不断增大。未退火样品的光致发光（PL）谱由361 nm附近的紫外带边发射峰和500 nm附近的深能级发射峰组成。样品经退火后,以500 nm为中心的绿带发射逐渐减弱,而带边发射强度有所增强,并且逐渐红移到366 nm附近,与吸收边移动的测试结果相吻合。对经过不同时间退火的样品分析表明,AZO薄膜的发光特性与退火时间也有很大关系,时间过短可见波段的发射较强,但时间过长会使晶粒发生团聚,导致紫外发射峰强度减弱。     

Preparation and photoluminescence of Sc-doped ZnO nanowires

We demonstrate bulk synthesis of single-crystal Sc-doped ZnO nanowires by using (Sc+Zn) powders at . These mass nanowires are characterized through X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy (TEM), selected area electron diffraction, and high-resolution TEM, which have uniform diameters of about 40 nm and microns of several decades in length. The growth of ZnScO nanowires is suggested for self-catalyzed vapor–liquid–solid. In particular, PL spectra of these nanowires show emission peaks that intensely shift to long wavelength with increasing Sc and the doping quantity is found responsible for the different characteristics, in which PL mechanism is explained in detail.     

Laser welding of thin polymer films to container substrates for aseptic packaging

Keyhole laser welding of polymers is a subject well covered and researched, but relatively little information exists regarding the welding of thin polymer films, particularly to a heavier substrate. This paper presents the design of a suitable test apparatus for laser welding thin film to a heavier substrate, and shows the results of an investigation into the feasibility of laser welding multi-layer polymer film lids to tubs for the manufacture of aseptic food containers. A consistent weld, free from defects, is the key to process success. Typical welding defects have been synthesised in order to investigate, and consequently remove, their cause. The result is a reliable welding method based on even film clamping. With careful attention to machine design, a seal of high mechanical strength and chemical integrity is possible.