Laser scribing of gallium doped zinc oxide thin films using picosecond laser

We report on a comprehensive study of picosecond laser scribing of gallium doped zinc oxide (GZO) thin films deposited on glass substrates using 355 nm, 532 nm and 1064 nm radiation, respectively. In this study, we investigated the influence of front side and rear side irradiation and determined single pulse ablation thresholds for all three wavelengths. Good ablation quality with full electrical isolation, steep groove walls and a smooth groove bottom was achieved by 355 nm rear side processing with a scanning speed of 224 mm/s. Ridges at the groove rims were found to be between 15 nm and 45 nm high. At similar scanning speed, laser scribing using 532 nm and 1064 nm radiation resulted in a lower ablation quality due to a higher roughness of the groove bottoms or higher ridges at the groove rims.     

Cathodoluminescence properties of silicon nanocrystallites embedded in silicon oxide thin films

Cathodoluminescence (CL) spectra for the Si nanocrystallites embedded in a matrix of silicon oxide films are measured at room temperature. The CL spectra consist of two principal bands whose peak energies are in a near-infrared (NIR) region (<1.6 eV) and in a blue region (2.6 eV), respectively. The spectral feature of the NIR CL band is similar to the corresponding PL spectra. The strong correlation between the presence of Si nanocrystallites and the formation of the NIR CL band are found as well as the PL spectrum. The peak energy of the blue CL band is slightly lower than that of the luminescence band originating from oxygen vacancies (≡Si–Si≡) in SiO₂. Therefore, the blue CL band is considered to come from Si_n clusters with n3 in the oxide matrix. Under irradiation of electron beams, degradation of the intensity is observed for both the CL bands but the decay characteristics are different.     

离子束反应溅射沉积SiO2薄膜的光学特性

 主要研究采用离子束反应溅射（RIBS）制备SiO2薄膜的折射率、消光系数、化学计量比与氧气在氩氧混合工作气体中含量及其沉积速率的关系。研究结果表明：RIBS制备的SiO2薄膜在0.63 μm处折射率n= 1.48,消光系数小于10-5;随着沉积速率的增加,薄膜的折射率和消光系数随之变大,当沉积速率超过0.3 nm/s,即使是在纯氧环境溅射,折射率值也不低于1.5;通过对红外透射光谱的主吸收峰位置研究得到沉积的SiO2薄膜为缺氧型,化学计量比不超过1.8,且红外吸收峰位置和SiO2折射率存在对应关系,因此在不加热衬底情况下使用RIBS制备SiO2薄膜时,会限制沉积速率的提高。     

纳秒激光作用下二氧化钒薄膜相变特性

采用脉冲激光沉积法制备了VO2薄膜,应用X射线衍射和X射线光电子能谱分析表明样品为多晶薄膜。采用泵浦-探针方法研究了二氧化钒薄膜的相变特性,实验结果表明当激光重复频率为160 Hz时,样品最小相变响应为12 ns,相变恢复时间与激光能量按照自然指数关系变化。仿真结果表明当激光能量一定时,二氧化钒薄膜相变恢复时间与衬底材料的热导率、热扩散系数有关。     

纳秒激光作用下二氧化钒薄膜相变特性

采用脉冲激光沉积法制备了VO2薄膜,应用X射线衍射和X射线光电子能谱分析表明样品为多晶薄膜。采用泵浦-探针方法研究了二氧化钒薄膜的相变特性,实验结果表明当激光重复频率为160 Hz时,样品最小相变响应为12ns,相变恢复时间与激光能量按照自然指数关系变化。仿真结果表明当激光能量一定时,二氧化钒薄膜相变恢复时间与衬底材料的热导率、热扩散系数有关。     

Patterned laser annealing of silicon oxide films

UV-absorbing silicon monoxide (SiO _x , x≈1) thin films on fused silica substrates are irradiated by an ArF excimer laser (wavelength 193 nm) in the sub-ablation threshold regime. Multi-pulse irradiation of films with ∼200-nm thickness at a fluence of about 100 mJ/cm² leads to a significant increase of the UV transmission, indicating the oxidation of SiO _x to SiO₂. The quality of the obtained films after this laser annealing process depends on the oxygen content of the environment. Irradiation in air at atmospheric pressure leads to the formation of sub-micron-sized oxide particles on top of the film. Structured illumination is applied either to form areas of the film with changed transmission and refractive index, or for the formation of regular particle patterns with sub-micron periods. These processes can be utilized for the fabrication of phase masks or for various types of surface functionalization.     

Pulsed laser deposition of oxide thin films

The pulsed laser deposition (PLD) process was studied in detail during oxide thin film growth by constructing a sophisticated PLD chamber combined with an energy-stable excimer laser. It was revealed that the transmitting laser energy at the entrance view port decreased exponentially with deposition runs, roughly by A e^−0.02x%, where A is the original transmission and x is the run number, and transmission loss could become considerable (up to 90%) in 100 deposition runs. In addition, area of the focused spot on the target was found a function of charging high voltage, which is a parameter of excimer laser operation, even through a slit forming rectangular sharp-edge beam profile. Laser energy density is one of the most important parameter governing grown film properties, and therefore accurate laser energy and spot area calibration is vital for reproducible film growth. In course of this study, the importance of spot area as well as the energy density is discussed in the view of deposition rate.     

碳化硅薄膜脉冲激光晶化特性研究

采用XeCl准分子激光对非晶碳化硅(a-SiC)薄膜的脉冲激光晶化特性进行了研究.通过原子力显微镜（AFM）和Raman光谱技术对退火前后薄膜样品的形貌、结构及物相特性进行了分析.结果表明，选用合适的激光能量采用激光退火技术能够实现a-SiC薄膜的纳米晶化.退火薄膜中的纳米颗粒大小随着激光能量密度的增加而增大；Raman谱分析结果显示了退火后的薄膜的晶态结构特性并给出了伴随退火过程存在的物相分凝现象.根据以上结果并结合激光退火特性，对a-SiC的脉冲激光晶化机理进行了讨论. 关键词： 激光退火 晶化 碳化硅     

Photoluminescence from Er-doped silicon rich oxide thin films

 Photoluminescence (PL) properties of Er-doped silicon rich oxide thin films deposited on Si substrate by co-evaporation of silicon monoxide and Er under different atmospheres are investigated. The samples exhibit luminescence peak at 1.54 μm which could be assigned to the recombination in intra-4f Er³⁺ transition. PL shows that this transition is highest when ammonia atmosphere is used during deposition followed by an annealing temperature at 850 °C in 95% N₂+5% H₂ gas (forming gas). In fact, we believe that the presence of the N atoms around Er ions increases the intensity of the 1.54 μm luminescence.     

Morphological and optical properties of silicon thin films by PLD

Silicon thin films have been prepared on sapphire substrates by pulsed laser deposition (PLD) technique. The films were deposited in vacuum from a silicon target at a base pressure of 10⁻⁶ mbar in the temperature range from 400 to 800 °C. A Q-switched Nd:YAG laser (1064 nm, 5 ns duration, 10 Hz) at a constant energy density of 2 J × cm⁻² has been used. The influence of the substrate temperature on the structural, morphological and optical properties of the Si thin films was investigated.Spectral ellipsometry and atomic force microscopy (AFM) were used to study the thickness and the surface roughness of the deposited films. Surface roughness values measured by AFM and ellipsometry show the same tendency of increasing roughness with increased deposition temperature.     

溶胶-凝胶法制备纳米多孔SiO2薄膜

以正硅酸乙酯(TEOS)为原料，采用旋转涂敷的方法，结合溶胶-凝胶技术在硅衬底上制备超低介电常数多孔SiO₂薄膜.采用两种不同的改性方法对薄膜表面进行改性，傅里 叶变换红外光谱分析发现改性后薄膜中含有大量的—CH₃键，从而减少了孔洞塌陷.用扫 描电子显微镜观察薄膜的表面形貌，发现薄膜内孔洞尺寸在70—80 nm之间.调节溶胶pH值，发现pH值越小凝胶时间越长.对改性样品热处理的结果表明，在300 ℃时介电常数最低达2.05. 关键词： 2')" href="#">多孔SiO₂ 低介电常数 溶胶-凝胶     

Structural and electrical properties of lithium manganese oxide thin films grown by pulsed laser deposition

LiMn₂O₄ thin films were deposited by reactive pulsed laser deposition technique and studied the microstructural and electrical properties of the films. The LiMn₂O₄ thin films deposited in an oxygen partial pressure of 100 mTorr and at a substrate temperature of 573 K from a lithium rich target were found to be nearly stoichiometric. The films exhibited predominantly (111) orientation representing the cubic spinel structure with Fd3m symmetry. The intensity of (111) peak increased and a slight shift in the peak position was observed with the increase of substrate temperature. The lattice parameter increased from 8.117 to 8.2417 Å with the increase of substrate temperature from 573 to 873 K. The electrical conductivity of the films is observed to be a strong function of temperature. The evaluated activation energy for the films deposited at 873 K is 0.64 eV.     

Electrical and optical properties of indium tin oxide thin films grown by pulsed laser deposition

Indium tin oxide (ITO) thin films (200-400 nm in thickness) have been grown by pulsed laser deposition (PLD) on glass substrates without a post-deposition anneal. The electrical and optical properties of these films have been investigated as a function of substrate temperature and oxygen partial pressure during deposition. Films were deposited at substrate temperatures ranging from room temperature to 300 °C in O₂ partial pressures ranging from 0.1 to 100 mTorr. For 300 nm thick ITO films grown at room temperature in oxygen pressure of 10 mTorr, the electrical conductivity was 2.6᎒^-3 Q^-1cm^-1 and the average optical transmittance was 83% in the visible range (400-700 nm). For 300 nm thick ITO films deposited at 300 °C in 10 mTorr of oxygen, the conductivity was 5.2᎒^-3 Q^-1cm^-1 and the average transmittance in the visible range was 87%. Atomic force microscopy (AFM) measurements showed that the RMS surface roughness for the ITO films grown at room temperature was ~7 Å, which is the lowest reported value for the ITO films grown by any film growth technique at room temperature.     

Pulsed laser deposition of NiMnGa thin films on silicon

Thin films of the magnetic shape-memory (MSM) material NiMnGa have been deposited on Si(100) substrates using pulsed laser deposition. The -–200 300nm-thick films were prepared at substrate temperatures ranging from 450 °C to 650 °C and at different background Ar pressures. Large saturation magnetizations, up to 60% of the bulk value, were measured for the films. Only the films deposited in vacuum or at Ar pressures below 10^-3 mbar and at temperatures between 500 °C and 600 °C were ferromagnetic. The films are mainly crystallized in the austenitic phase and they have a smooth surface with a low droplet density (0.01 m^-2). The magnetization and surface quality are sufficient that the films could be utilized in the realization of thin-film MSM devices. PACS 75.70.Ak     

Pulsed laser deposition of molybdenum oxide thin films

Thin films of molybdenum oxide were deposited in vacuum by pulsed laser ablation using a xenon fluoride (351 nm) and a krypton fluoride (248 nm) excimer lasers. The films were deposited on unheated substrates and were post-annealed in air in the temperature range 300–500°C. The structural, morphological, chemical, and optical properties of the films were studied. As-deposited films were found to be dark. The transparency of the films was improved with annealing in air. The films were polycrystalline with diffraction peaks that belong to the orthorhombic phase of MoO₃. The surface morphology of the films showed a layered structure. Both the grain size and surface roughness increased with annealing temperature. The stoichiometry of the films improved upon annealing in air, with the best stoichiometry of MoO_2.95 obtained for films deposited by the XeF laser and annealed at 400°C. Similarly, the best transparency, with a transmittance exceeding 80%, was obtained with the films annealed in the temperature range 400–450°C.     

Electrical properties of thin PECVD silicon oxynitride films

Thin silicon oxynitride films with excellent uniformity were prepared by plasma enhanced CVD. Oxygen incorporation leads to improved breakdown behavior and to reduction of the film conductivity compared to PECVD silicon nitride layers. Thin PECVD silicon oxynitride films deposited on single crystal and poly-Si exhibit good insulation properties in both cases.     

Deposition of zinc oxide thin films by reactive pulsed laser ablation

Thin films of zinc oxide have been deposited by reactive pulsed laser ablation of Zn and ZnO targets in presence of a radio frequency (RF) generated oxygen plasma. The gaseous species have been deposited at several substrate temperatures, using the on-axis configuration, on Si (1 0 0). Thin films have been characterized by scanning electron microscopy, atomic force microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and infrared spectroscopy. A comparison among conventional PLD and reactive RF plasma-assisted PLD has been performed.     

Optical properties of stannous oxide thin films

Thin films of stannous oxide (SnO) have been prepared by the electron-beam evaporation method. Film properties, such as refractive indexn, extinction indexk, and absorption coefficient, were studied in the wavelength range between 200 nm and 2 000 nm with different methods. The surface roughness of SnO thin films has been found to depend linearly on the film thickness in the range 400 <d < 2 000 nm. The optical transition in SnO thin films shows direct transition corresponding to an optical gap of 2.85 eV.