Flame retardant epoxy polymers based on all phosphorus-containing components

A phosphorus-containing epoxy resin, bis(3-t-butyl-4-glycidyloxyphenyl-2,4-di-t-butylphenyl)resorcinol diphosphate, was synthesized and subsequently cured with non-phosphorus containing amines, and/or novel phosphorus-containing aromatic or polyoxyalkylene amines. Chemical structures of these materials were characterized with FTIR, NMR, elemental analysis, and amine titration. The introduction of soft -P-O- linkage, polyoxyalkyene, or hard aromatic group into the backbones of the synthesized phosphorus-containing amines provides epoxy polymers with high phosphorus contents and tailored flexibility. Thermal analysis of differential scanning calorimeter and thermal gravimetric analysis (TGA) reveals that these resulted epoxy polymers possess moderate T_gs and thermal stability. Furthermore, high char yields in TGA analysis and high limited oxygen index values indicate that these phosphorus-containing epoxy polymers possess excellent flame retardant properties.     

Thermal degradation of a reactive flame retardant based on cyclotriphosphazene and its blend with DGEBA epoxy resin

Hexaglycidyl cyclotriphosphazene (HGCP) was synthesized, and characterized by FTIR, ³¹P, ¹H, and ¹³C-NMR. This compound was used as a reactive flame retardant to blend with commercial epoxy resin DGEBA (Diglycidyl ether of bisphenol A). Its effect on the DGEBA decomposition pathways was characterized by studying both gas and solid phases produced during thermogravimetric analysis (TGA). The gases evolved during TGA in air were studied by means of thermogravimetry coupled with Fourier transform infrared spectroscopy (TG–FTIR), while the solid residues were analysed by FTIR and scanning electron microscopy (SEM). The results showed that HGCP presents a good dispersion in DGEBA, and the blend thermoset with 4,4′-methylene-dianiline (MDA) curing agent leads to a significant improvement of the thermal stability at elevated temperature with higher char yields compared with pure DGEBA thermoset with the same curing agent. Improvement has also been observed in the fire behaviour of blend sample.     

Thermal properties of epoxy resin nanocomposites based on hydrotalcites

Epoxy resin nanocomposites containing home-made hydrotalcites (HTlc) have been prepared and their properties have been studied and compared with those of montmorillonite (MMT)-type layered silicates-based nanocomposites. Nanofiller dispersion in the polymer matrix has been evaluated by transmission (TEM) electron microscopy and wide angle X-ray diffraction (WAXD), while nanocomposite thermal properties have been studied in detail by thermogravimetric analysis (TGA/DTG) and cone calorimeter tests.The morphological studies have shown that the compatibilisation of the above two type of nanofillers allowed us to obtain nanostructured materials. As far as thermal properties are concerned, nanocomposites based on HTlc are found to decompose, both in air and nitrogen, following a trend similar to that of the neat polymer matrix, while in the case of the nanocomposite based on the organophilic MMT a slight improvement was found in air. Conversely, cone calorimetric tests have demonstrated that only the organophilic hydrotalcite was capable of decreasing the peak of the heat release rate in a relevant way.     

The non-halogen flame retardant epoxy resin based on a novel compound with phosphaphenanthrene and cyclotriphosphazene double functional groups

A novel flame retardant additive hexa-(phosphaphenanthrene -hydroxyl-methyl-phenoxyl)-cyclotriphosphazene (HAP-DOPO) with phosphazene and phosphaphenanthrene double functional groups has been synthesized from hexa-chloro-cyclotriphosphazene, 4-hydroxy-benzaldehyde and 9,10-dihydro-9-oxa-10- phosphaphenanthrene 10-oxide(DOPO). The structure of HAP-DOPO was characterized by Fourier transformed infrared (FT-IR) spectroscopy and ¹H nuclear magnetic resonance (¹H NMR) and ³¹P nuclear magnetic resonance (³¹P NMR). The additive HAP-DOPO was blended into diglycidyl ether of bisphenol-A (DGEBA) to prepare flame retardant epoxy resins. The flame retardant properties and thermal properties of the epoxy resins cured by 4, 4′-Diamino-diphenyl sulfone (DDS) were investigated from the differential scanning calorimeter (DSC), the thermogravimetric analysis (TGA), UL94 test, the limiting oxygen index (LOI) test and Cone calorimeter. Compared to traditional DOPO-DGEBA and ODOPB-DGEBA thermosets, the HAP-DOPO/DGEBA thermosets have higher T_gs at the same UL94 V-0 flammability rating for their higher crosslinking density and have higher char yield and lower pk-HRR at same 1.2 wt.% phosphorus content which confirm that HAP-DOPO has higher flame retardant efficiency on thermosets. The scanning electron microscopy (SEM) results shows that HAP-DOPO in DGEBA/DDS system obviously accelerate formation of the sealing, stronger and phosphorus-rich char layer to improve flame retardant properties of matrix during combustion.     

Synthesis of three novel phosphorus-containing flame retardants and their application in epoxy resins

One symmetric diamine (4) and two symmetric phenols (5) and (6) were synthesized as phosphorus-containing flame retardants. The synthesis comprised a two-step procedure: the condensation of p-phenylenediamine with benzaldehyde, 4-hydroxybenzaldehyde and 2-hydroxybenzaldehyde respectively, followed by the addition of 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide to the imine linkage. The structures of (4)-(6) were characterized by FTIR, NMR and mass spectra. (4)-(6) served as co-curing agents of diaminodiphenylmethane for epoxy resins, and epoxy thermosets exhibited excellent flame retardancy, moderate changes in glass transition temperature (T_g) and thermal stability. When the phosphorus content reached 1.0 wt.%, the epoxy resin system met the UL-94 V-0 classification and the limiting oxygen index (LOI) reached more than 35.6, probably because of the nitrogen-phosphorus synergistic effect.     

Pyrolysis and fire behaviour of epoxy resin composites based on a phosphorus-containing polyhedral oligomeric silsesquioxane (DOPO-POSS)

The pyrolysis and fire behaviour of epoxy resin (EP) composites based on a novel polyhedral oligomeric silsesquioxane containing 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO-POSS) and diglycidyl ether of bisphenol A (DGEBA) have been investigated. The pre-reaction between the hydroxyl groups of DOPO-POSS and the epoxy groups of DGEBA at 140 °C is confirmed by FTIR, which means that DOPO-POSS molecules of hydroxyl group could easily disperse into the epoxy resin at the molecular level. The EP composites with the DOPO-POSS were prepared through a curing agent, m-phenylenediamine (m-PDA). The morphologies of the EP composites observed by SEM indicate that DOPO-POSS disperses with nano-scale particles in the EP networks, which implies good compatibility between them. The thermal properties and pyrolysis of the EP composites were analyzed by DSC and TGA, TGA-FTIR, and TGA-MS. The analysis indicates that the DOPO-POSS change the decomposition pathways of the epoxy resin and increase its residue at high temperature; moreover, the release of phosphorous products in the gas phase and the existence of Si-O and P-O structures in the residue Is noted. The fire behaviour of the EP composites was evaluated by cone calorimeter (CONE). The CONE tests show that incorporation of DOPO-POSS into epoxy resin can significantly improve the flame retardancy of EP composites. SEM and XPS were used to explore micro-structures and chemical components of the char from CONE tests of the EP composites, they support the view that DOPO-POSS makes the char strong with the involvement of Si-O and P-O structures.     

Novel flame retardancy effects of DOPO-POSS on epoxy resins

A series of flame retarded epoxy resins (EP) was prepared with a novel polyhedral oligomeric silsesquioxane containing 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO-POSS). The flame retardancy of these EPs was tested by the LOI, UL-94, which indicates that DOPO-POSS has meaningful effects on the flame retardancy of EP composites. 2.5 wt.% DOPO-POSS incorporation into epoxy resin (EP-2.5), results in a LOI value 30.2 and UL-94 V-1 (t₁ = 8 s and t₂ = 3 s) rating. Moreover, self-extinguishing effect through the pyrolytic gases spurt is observed in UL-94 test for the EP-2.5. The pyrolytic gases and thermal stability of epoxy resins with and without DOPO-POSS were detected by TGA-FTIR under air atmosphere. Releases of gaseous species are found to be similar for the pure EP and EP-2.5. The details of fire behaviour, such as TTI, HRR, p-HRR, TSR, SEA, COPR, CO₂PR, and TML, were tested by cone calorimeter. It is notable that 2.5 wt.% DOPO-POSS could make COPR and CO₂PR reach a maximum, which could explain the blowing-out extinguishing effect.     

Influence of oxidation state of phosphorus on the thermal and flammability of polyurea and epoxy resin

The focus of this study is an investigation of the effect of oxidation state of phosphorus in phosphorus-based flame retardants on the thermal and flame retardant properties of polyurea and epoxy resin. Three different oxidation states of phosphorus (phosphite, phosphate and phosphine oxide) additives, with different thermal stabilities at a constant phosphorus content (1.5 wt.%) have been utilized. Thermal and flame retardant properties were studied by TGA and cone calorimetry, respectively. The thermal stability of both polymers decreases upon the incorporation of phosphorus flame retardants irrespective of oxidation state and a greater amount of residue was observed in the case of phosphite. Phosphate was found to be better flame retardant in polyurea, whereas phosphite is suitable for epoxy resin. Phosphite will react with epoxy resin by trans-esterification, which is demonstrated by FTIR and ³¹P NMR. Further, TG–FTIR and XPS studies also provide information on flame retardancy of both polymers with phosphorus flame retardants.     

Synthesis, characterization, thermal properties and flame retardancy of a novel nonflammable phosphazene-based epoxy resin

Hexakis(4-hydroxyphenoxy)-cyclotriphosphazene (PN-OH) was synthesized through nucleophilic substitution of the chloride atoms of hexachlorocyclotriphosphazene and reduction of the aldehyde groups, and its chemical structure was characterized by elemental analysis, ¹H and ³¹P NMR, and Fourier transform infrared (FTIR) spectroscopy. A new phosphazene-based epoxy resin (PN-EP) was successfully synthesized through the reaction between diglycidyl ether of bisphenol-A (DGEBA) and PN-OH, and its chemical structure was confirmed by FTIR and gel permeation chromatography. Four PN-EP thermosets were obtained by curing with 4,4′-diaminodiphenylmethane (DDM), dicyandiamide (DICY), novolak and pyromellitic dianhydride (PMDA). The reactivity of PN-EP with the four curing agents presents an increase in the order of DDM, PMDA, novolak and DICY. An investigation on their thermal properties shows that the PN-EP thermosets achieve higher glass-transition and decomposition temperatures in comparison with the corresponding DGEBA ones while their char yields increase significantly. The PN-EP thermosets also exhibit excellent flame retardancy. The thermosets with novolak, DICY and PMDA achieve the LOI values above 30 and flammability rating of UL94 V-0, whereas the one with DDM reaches the V-1 rating. The nonflammable halogen-free epoxy resin synthesized in this study has potential applications in electric and electronic fields in consideration of the environment and human health.     

Synthesis of phosphorus-based flame retardant systems and their use in an epoxy resin

Methods are proposed to synthesize efficient organophosphorous compounds and combine them with montmorillonite nanoparticles. The chemical-physical structure and mechanism of action of the new systems were studied in epoxy resin. Best results were achieved using the fully phosphorylated calixresorcinarene derivative: the heat release rate peak could be decreased by 61% and the LOI value was increased from 21 to 28. The salt form of additives in case of phosphorylated phloroglucine derivatives was not advantageous in epoxy resin, because the additives could not participate in the crosslinking process effectively due to their inhomogenous distribution in the matrix. The incorporation of the nanoparticles did not create the desired flame retardant effect which can be explained by the increased heat conductivity and lower mobility of the nanoparticles due to the crosslinked structure.     

Synthesis and effect of hyperbranched (3-hydroxyphenyl) phosphate as a curing agent on the thermal and combustion behaviours of novolac epoxy resin

A novel type of hyperbranched (3-hydroxyphenyl) phosphate (HHPP) with high functionality as a curing agent of epoxy resins was synthesized and characterized by FTIR, ¹H NMR and vapor phase osmometry (VPO). The cured epoxy resin with HHPP possessed improved glass transition temperature. The thermostability and flame retardancy of O-cresol novolac epoxy resin cured with different contents of HHPP were investigated by thermogravimetric analysis (TGA), limiting oxygen index (LOI) and cone calorimetry. The obtained results show that the samples containing a higher percentage of HHPP exhibit relatively lower thermostability at lower temperature while higher thermostability at elevated temperature and more char was formed compared with those containing a lower percentage of HHPP. The LOI value increased from 22.0 to 30.0 when HHPP, instead of 1,3-dihydroxybenzene, was used as a curing agent. The 25 wt% addition of HHPP in the curing agent complex effectively decreased the heat release rate and improved the char yield to the content nearly similar as those of the epoxy resin cured with pure HHPP.     

Effect of a phosphorus-containing flame retardant on the thermal properties and ease of ignition of poly(lactic acid)

An aryl polyphenylphosphonate, poly(9-oxa-10-(2,5-dihydro-xyphenyl) phospha-phenanthrene-10-oxide) phenylphosphonate (WLA-3), was used to prepare a flame-retardant poly(lactic acid) (PLA) by direct melt compounding. The thermal behaviour, burning behaviour and mechanical properties of the flame-retardant PLA systems have been investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), vertical burning test (UL-94), limiting oxygen index (LOI), cone calorimeter test (CCT) and tensile test. The flame retardance mechanism has been studied via Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC), and P content analysis. The UL-94 ratings of PLA’s containing 7phr (W_7P) and 10phr (W_10P) of WLA-3 were enhanced to V-0 from no rating for neat PLA. However, the cone calorimetry of flame-retardant PLA (W_7P) only showed a little decrease in heat release rate (HRR), peak of heat release rate (PHRR) and total heat release (THR) compared to neat PLA. TGA results showed that the PLA containing different amounts of WLA-3 presented more complicated thermal decomposition behaviours than neat PLA. Additionally, the results from DSC and tensile tests showed that the addition of WLA-3 into PLA had a slight impact on the crystallization behaviours and tensile properties.     

The effect of a novel phosphorus-nitrogen reactive flame retardant curing agent on the performance of epoxy resin

A phosphorus-nitrogen reactive flame retardant curing agent poly-(isophorondiamine spirocyclic pentaerythritol bisphosphonate) (PIPSPB) was synthesized. The chemical structure of the obtained compound was identified by FTIR, ¹HNMR, and mass spectroscopies. Different proportions of DDS and PIPSPB were compounded as the curing agents to prepare a series of flame retardant epoxy resins with different phosphorus contents. The curing behavior of E-44/PIPSPB?+?DDS system was studied by DSC. A series of tests were conducted to characterize E-44/PIPSPB?+?DDS thermosetting system’s performance. The result demonstrates that the residual carbon content of EP/PIPSPB?+?DDS system is obviously higher than that of EP/DDS system after 500?°C with the increase of phosphorus content in the system, and the heat release rate of the system during combustion is significantly reduced. The generated phosphorus-containing carbon layer is obviously foamed, which shows that the flame retardancy of the system is the result of the combined action of condensed phase and gas phase. When the phosphorus content is 1.77wt%, EP-3 successfully passed UL94 V-0 flammability rating, the LOI value was as high as 29%, the impact strength and tensile strength of it were 6.08KJ/m² and 49.10MPa respectively, the adhesive strength could reach 13.89?MPa, the system presents a good overall performance.     

Synthesis and properties of isosorbide based epoxy resin

Isosorbide based epoxy resin (IS-EPO) of epoxy number: 0.44 mol/100 g was synthesised in the one step reaction from 1,4:3,6-dianhydro-d-glucitol (isosorbide) and epichlorohydrin in the presence of concentrated aqueous NaOH. The product obtained was characterised by means of NMR, FT-IR and ESI MS spectroscopy. Compositions with typical hardeners were prepared and cured. The thermal and mechanical properties of the resulting materials were evaluated. Comparison with commercially available epoxy resin Epidian 5 shows relatively good mechanical performance of IS-EPO which makes isosorbide a promising candidate to replace bisphenol A (BPA).     

Synthesis and properties of a phosphorus-containing flame retardant epoxy resin based on bis-phenoxy (3-hydroxy) phenyl phosphine oxide

A reactive phosphorus-containing compound, bis-phenoxy (3-hydroxy) phenyl phosphine oxide (BPHPPO) was first successfully synthesized to produce the phosphorus-containing flame retardant epoxy resin (BPHPPO-EP). The chemical structures were characterized from FTIR, MS, NMR spectra and elemental analyses. Thermal degradation behaviors and flame retardant properties of the cured epoxy resins were investigated from the thermogravimetric analysis (TGA) and the limiting oxygen index (LOI) test using 4,4′-diaminodiphenylsulfone (DDS) as curing agent. The high char yields and the high limiting oxygen index values were found to certify the great flame retardancy of this phosphorus-containing epoxy resin.     

Studies on the effect of different levels of toughener and flame retardants on thermal stability of epoxy resin

A thermoplastic toughener, polyether sulphone (PES) and a number of different types of flame retardants were blended in different ratios with a commercial epoxy resin triglycidyl-p-aminophenol (TGAP) and 4,4-diamino diphenyl sulphone (DDS) a curing agent. The effect of type and levels of flame retardants (FR) and the toughening agent on the curing, thermal decomposition and char oxidation behaviour of the epoxy resin was studied by the simultaneous differential thermal analysis and thermogravimetric techniques. It was observed that the toughener slightly increases the curing temperature (by up to 20 °C) but had minimal effect on the decomposition temperature of the resin. Flame retardants, however affected all stages depending upon the type of flame retardant used. The curing peak for samples containing tougher and flame retardants although slightly changed depending upon the type of FR, was not more than ± 20 °C compared to that of samples containing toughener only. All flame retardants lowered the decomposition temperature of the epoxy resin. Phosphorus- and nitrogen-containing flame retardants reduced the char oxidation leading to more residual char, whereas halogen- containing flame retardants had less effect on this stage.     

Preparation and thermal properties of a novel flame-retardant coating

A novel silicone and phosphate modified acrylate (DGTH) was synthesized and characterized by ¹H NMR and FTIR. It was found that DGTH could be cured both by UV radiation and moisture mode with FTIR. The flammability and thermal behavior of the cured film were studied by the limited oxygen index (LOI), thermogravimetric analysis (TG) and real time Fourier transform infrared (RT-FTIR). The LOI value of the cured film is 48 and the TG data shows that the cured film has three characteristic degradation temperature regions, attributing to the decomposition of phosphate and polyurethane to alcohols and isocyanates, thermal pyrolysis of alkyl chains, and decomposition of unstable structures in char, respectively. The RT-FTIR data implies that the degraded products of phosphate form poly(phosphoric acid) further catalyse the breakage of carbonyl groups to form an intumescent char, preventing the samples from further burning.     

Effects of zinc-based flame retardants on the degradation behaviour of an aerospace epoxy matrix

Flame behaviour is a fundamental requirement for advanced aerospace composites. In this work, a commercial, low-viscosity epoxy system, typically used in liquid infusion composite processes, and its mixtures with three different zinc-based flame retardants (ZB, ZS, ZHS) at different weight percentages has been investigated by cone calorimetry and thermogravimetric analysis.Cone calorimetry has been performed to verify the flame retardancy effects induced by each filler composition. Nevertheless manufacturability issues require the evaluation of the rheological changes induced by filler on the unloaded matrix system. Rheological tests have been, therefore, performed to identify the maximum concentration of filler. Based on these results thermogravimetric tests have been performed to investigate thermal degradation kinetics of selected systems. The feasibility of Kissinger and Flynn-Wall-Ozawa method for the determination of characteristic degradation kinetics parameters has been evaluated and results were analysed. A simplified decomposition model was assumed to analyse epoxy degradation behaviour; it was found that this model gives appreciable matching with experimental TGA curve trend for neat epoxy whereas for the filled compounds additional stages were assume to occur.     

Intrinsically flame retardant epoxy resin - Fire performance and background - Part I

The flame retardant effect of newly synthesized phosphorus-containing reactive amine, which can be used both as crosslinking agent in epoxy resins and as a flame retardant, was investigated. The effect of montmorillonite and sepiolite additives on the fire induced degradation was compared to pristine epoxy resin. The effect of combining the organophosphorous amine with clay minerals was also studied. It could be concluded that the synthesized phosphorus-containing amine, TEDAP can substitute the traditional epoxy resin curing agents providing additionally excellent flame retardancy: the epoxy resins flame retarded this way reach 960 °C GWFI value, 33 LOI value and V-0 UL-94 rating - compared to the 550 °C GWFI value, 21 LOI value and “no rate” UL-94 classification of the reference epoxy resin. The peak of heat release was reduced to 1/10 compared to non-flame retarded resin, furthermore a shift in time was observed, which increases the time to escape in case of fire. The flame retardant performance can be further improved by incorporating clay additives: the LOI and the HRR results showed that the optimum of flame retardant effect of clay additives is around 1 mass% filler level in AH-16-TEDAP system. Applying a complex method for mechanical and structural characterization of the intumescent char it was determined that the flame retarded system forms significantly more and stronger char of better uniformity with smaller average bubble size. Incorporation of clay additives (owing to their bubble nucleating activity) results in further decrease in average bubble diameter.     

有机磷系及石墨烯阻燃环氧树脂研究进展

环氧树脂作为一种优异的树脂基体,被广泛地应用于众多领域,但因其极易燃烧,所以常常需要对其进行阻燃处理。本文简要综述了近几年有机磷系化合物及石墨烯阻燃环氧树脂的研究进展,其中有机磷系化合物阻燃部分重点介绍了以阻燃剂中间体9,10-二氢-9-氧杂-10-磷杂菲-10-氧化物(DOPO)及其衍生物和聚磷酸铵(APP)为代表的含磷阻燃剂在环氧树脂中的阻燃机理和阻燃进展;同时也介绍了石墨烯及其衍生物在环氧树脂阻燃领域的最新研究进展,并对其发展前景进行了展望。