新型双钼酸盐红色荧光粉的制备及发光性能研究

采用高温固相法合成了一种新型的白光LED用双钼酸盐红色荧光粉,利用XRD,F-4500等对其进行了研究。结果表明:该系列荧光粉可以被近紫外光(396 nm)和蓝光(466 nm)有效激发,发射峰值位于615 nm(Eu3+离子的5D0→7F2跃迁)的红光;而且在钾铕双钼酸盐荧光粉KEu(MoO4)2中引入适量的钨酸能加强其发光强度,而不改变样品的发射光谱的形状和发射峰的位置。此外,在确定WO24-/MoO42最佳比值的前提下,文章还详细探讨了碱金属离子相互置换对样品发光性能影响的机制。     

白光LED用KCaPO4:Eu3+红色荧光粉制备及其发光特性

采用高温固相法制备了KCaPO4:Eu3+红色发光材料,研究了Eu3+掺杂浓度、电荷补偿剂等对材料发光性质的影响.结果显示,在397 nm近紫外光激发下,材料呈多峰发射,分别由Eu3+的5D0→7FJ(J=0,1,2,3,4)能级跃迁产生,主峰为613 nm;监测613 nm发射峰,所得激发光谱由O2-→Eu3+电荷迁移带(200～350 nm)和f-f高能级跃迁吸收带(350～450 nm)组成,主峰为397 nm.Eu3+离子的最佳掺杂浓度为5%(摩尔分数);浓度猝灭机制为电偶极-电偶极相互作用.添加电荷补偿剂Li+,Na+,K+或Cl-后,可提高KCaPO4:Eu3+材料的发射强度,其中以添加Li+时,效果最明显.     

白光LED用Eu掺杂红色荧光粉

白光LED因亮度高、体积小、寿命长、高效节能、绿色环保等优点而引起人们的广泛关注,但是目前大部分白光LED用荧光粉的不足之处在于其发光效率较低,显色指数较差,色温较高,成本较高等等。红色荧光粉可明显改善白光LED的色温和显色指数,因此红色荧光粉在调制白光LED和改善其显色指数方面具有至关重要的作用。近年来红色荧光粉得到了深入研究,并有不少文献报道了新型的红色荧光粉。本文介绍了Eu~(3+)掺杂的线状红光发射荧光粉、Eu~(2+)掺杂的带状红光发射荧光粉并着重介绍了Eu~(2+)掺杂的新型窄带红光发射荧光粉,以及目前Eu掺杂红色荧光粉发展的不足及其改善方法。     

白光LED用Eu掺杂红色荧光粉

白光LED因亮度高、体积小、寿命长、高效节能、绿色环保等优点而引起人们的广泛关注,但是目前大部分白光LED用荧光粉的不足之处在于其发光效率较低,显色指数较差,色温较高,成本较高等等。红色荧光粉可明显改善白光LED的色温和显色指数,因此红色荧光粉在调制白光LED和改善其显色指数方面具有至关重要的作用。近年来红色荧光粉得到了深入研究,并有不少文献报道了新型的红色荧光粉。本文介绍了Eu³⁺掺杂的线状红光发射荧光粉、Eu²⁺掺杂的带状红光发射荧光粉并着重介绍了Eu²⁺掺杂的新型窄带红光发射荧光粉,以及目前Eu掺杂红色荧光粉发展的不足及其改善方法。     

KLa(MoO_4)_2∶Eu~(3+)红色荧光粉的合成和发光性能

采用高温固相法制备了KLa(MoO4)2∶Eu3+红色荧光粉,对其物相结构、光谱性质进行了分析,研究了Eu3+的不同掺杂浓度对荧光粉的发光性能的影响,同时对其色坐标进行了分析.结果表明,KLa(MoO4)2为体心对称的单斜相;KLa(MoO4)2∶Eu3+荧光粉中Eu3+的最佳掺杂浓度为9%,当掺杂浓度大于9%出现浓度猝灭现象,出现这一现象的主要原因是由于交换作用导致Eu3+之间能量的转移.     

白光LED用红色发射荧光粉Gd2(MoO4)3:Eu3+制备与表征

以NH4F为助熔剂采用固相反应法合成了Eu^3＋掺杂的α—Gd2（MoO4）3荧光粉。研究了引入不同含量助熔剂时对材料的结晶、荧光粉颗粒粒径、表面形貌及光谱性质的影响。实验结果表明,引入重量比为3％时样品具有好的结晶和优良的光谱性质;同时,随着助熔剂量的增加Eu^3＋离子在晶体中所处的格位对称性发生了变化;另外,通过Eu^3＋掺杂浓度变化的结果讨论了Eu^3＋的浓度猝灭行为。光谱测量的结果表明,该荧光粉与其他商品荧光粉不同,其最有效的激发波长不在电荷迁移带范围,而是465和395nm跃迁,该荧光粉可作为近紫外LED和三基色荧光粉组合型自光器件的红色荧光粉的候选材料。     

Ca10(Si2O7)3Cl2:Eu2+Mn2+单-基质白光荧光粉的发光性质

用高温固相法合成了颜色可调的Ca10(Si2O7)3Cl2:Eu2+Mn2+荧光粉.研究了它的发光性质和Eu2+与Mn2+之间的能量传递.Eu2+离子在Ca10(Si2O7)3Cl2晶体中形成了峰值为426 nm和523 nm的5d→4f跃迁发光,Eu2+中心向Mn2+中心传递能量,敏化Mn2+离子4T1(4G)-6A1(6S)跃迁而产生585 nm的黄光发射.黄绿蓝3个发射带叠加在单一基质中实现了白光发射.3个发射带的激发谱范围位于250-480 nm处,Ca10(Si2O7)3Cl2:Eu2+Mn2+在紫外-近紫外波段(350～410 nm)范围内有很强的激发,是一种适合InGaN管芯激发的单一基质白光LED荧光粉.     

红色荧光粉KYyEu1-y(WO4)x(MoO4)2-x的制备及其发光性能研究

采用高温固相法结合超声波技术合成了红色荧光粉KYyEu1-y(WO4)x(MoO4)2-x系列,探讨了其合成工艺条件,确定了最佳烧结温度为750℃,烧结时间为5 h;并确定了当x=0.5,y=0.1时样品的相对发光亮度达到最大值为118.2,发射峰的位置处在615nm附近(Eu3+离子的5Do→7F2跃迁),色纯度高,显色性能好.经过研究发现,随着钨酸盐的浓度增加,以466 nm波长激发时,Eu3+的5Do→7F2跃迁发射强度也相应增加,当Mo/W=3时亮度达到最大值.     

Gd3+掺杂对NaY(MoO4)2:Eu3+荧光粉发光性能影响的研究

采用微乳液-水热法制备了NaY(MoO4)2∶Eu3+和Na(Y,Gd)(MoO4)2∶Eu3+荧光粉.利用X射线衍射(XRD)、扫描电镜(SEM)和荧光光谱手段对样品进行了表征.所制样品的X射线衍射峰与标准卡片PDF# 82-2369基本吻合.SEM图谱显示所制备的纳米粒子直径为0.5～0.8μm.激发-发射光谱显示...     

非晶红色荧光粉Cd3AlSi3O12:Eu3+的制备及发光性能

使用溶胶-凝胶法制备了Cd3Al2Si3O12:Eu3+非晶体系红色荧光粉,并对其发光性质进行了研究.该荧光粉在Eu3+的位于394 nm的5L6能级和464 nm的5D2能级的激发下能够产生强的5D0→7F的红光特征发光,最佳掺杂摩尔分数为25％.Cd3Al2Si3O12:Eu3+荧光粉与传统的Y2O3:Eu3+相比较,其发光强度是Y2O3:Eu3+的2.4倍左右(在394和464 nm的激发下).Cd3Al2Si3O12:Eu3+的热稳定性好,比已经商业化的YAG:Ce3+的热猝灭影响要小得多.所有这些结果表明Cd3A12Si3O12:Eu3+可作为暖白光LED用红色荧光粉.     

Mechanistic Insight into Energy-Transfer Dynamics and Color Tunability of Na4CaSi3O9:Tb3+,Eu3+ for Warm White LEDs

In this work, a latent energy-transfer process in traditional Eu³⁺,Tb³⁺-doped phosphors is proposed and a new class of Eu³⁺,Tb³⁺-doped Na₄CaSi₃O₉ (NCSO) phosphors is presented which is enabled by luminescence decay dynamics that optimize the electron-transfer energy process. Relative to other Eu³⁺,Tb³⁺-doped phosphors, the as-synthesized Eu³⁺,Tb³⁺-doped NCSO phosphors show improved large-scale tunable emission color from green to red upon UV excitation, controlled by the Tb³⁺/Eu³⁺ doping ratio. Detailed spectroscopic measurements in the vacuum ultraviolet (VUV)/UV/Vis region were used to determine the Eu³⁺–O²⁻ charge-transfer energy, 4f–5d transition energies, and the energies of 4f excited multiplets of Eu³⁺ and Tb³⁺ with different 4f^N electronic configurations. The Tb³⁺→Eu³⁺ energy-transfer pathway in the co-doped sample was systematically investigated, by employing luminescence decay dynamics analysis to elucidate the relevant energy-transfer mechanism in combination with the appropriate model simulation. To demonstrate their application potential, a prototype white-light-emitting diode (WLED) device was successfully fabricated by using the yellow luminescence NCSO:0.03Tb³⁺, 0.05Eu³⁺ phosphor with high thermal stability and a BaMgAl₁₀O₁₇:Eu²⁺ phosphor in combination with a near-UV chip. These findings open up a new avenue to realize and develop multifunctional high-performance phosphors by manipulating the energy-transfer process for practical applications.     

Synthesis and Luminescent Properties of Novel Nanometer-sized ScAlMgO_4：Eu~（3＋） Phosphors for PDP

Novel nanometer-sized ScAlMgO4:Eu3+ phosphors were successfully synthesized by the citric acid complexation method.The mean particle size of the obtained powders was within the range of 100～150 nm according to the SEM patterns.In ScAlMgO4:Eu3+ showed strong characteristic red emission,of which the maximum emission peak was located at 629 nm for ultraviolet(UV) excitation.The dependence of photoluminescence intensity on Eu3+ concentration was also studied in detail,and the emission intensity of Sc1-xEuxAlMgO4 was about 10% at optimized Eu3+ concentration.Furthermore,the luminescence decay measurements showed that the lifetimes of Eu3+ were in the range of millisecond.The obtained ScAlMgO4:Eu3+ phosphors with nanometer size and excellent luminescence efficiency would be potential red phosphors in plasma display panels.     

形貌可控的LaPO4:Eu3+荧光粉的制备与发光性能研究

分别以硝酸镧、多聚磷酸和磷酸二氢钠为原料,在无任何添加剂和模板的条件下,采用水热法分别合成微纳米球和纳米棒两种形貌的磷酸镧.通过场发射-扫描电子显微镜(FE-SEM),X射线衍射(XRD),红外光谱(FTIR)和荧光光谱(PL)等测试手段对以上不同形貌的样品的相结构以及微观形貌进行表征.FE-SEM测试结果表明:当以多聚磷酸为磷源时,在酸性条件下可以得到平均粒径约为2μm左右的磷酸镧微球;而当以磷酸二氢钠磷源时,在酸性条件下则可以得到纳米棒;两者的分散性良好.XRD测试结果表明:两种不同形貌的样品均为单斜晶系结构.荧光光谱分析可知:Eu3+的掺杂浓度相同时,球状样品的发光强度远大于棒状样品.     

全光谱白光发光二极管用Eu3+掺杂Ca2KZn2(VO4)3黄色荧光粉的制备及光学性能

基于蓝光芯片激发黄色荧光粉或近紫外芯片激发三基色荧光粉构建的白光发光二极管(WLED)在青光区域呈现明显的凹口,导致白光的色彩性能不够理想。为了弥补这一缺陷,实现全光谱白光,我们设计了Eu³⁺掺杂Ca₂KZn₂(VO₄)₃黄色荧光粉,其发射波长范围为400~750 nm。在387 nm激发下,在所制荧光粉中可同时获得来自VO₄^3-基团和Eu³⁺的发射光。Eu³⁺在Ca₂KZn₂(VO₄)₃基质中的最佳掺杂浓度(物质的量分数)为0.05,且VO₄^3-基团向Eu³⁺的能量传递效率达到64.9%。基于变温的发射光谱,揭示了所制荧光粉的热稳定性并发现VO₄^3-基团和Eu³⁺的激活能分别为0.538和0.510 eV。此外,将所制黄色荧光粉与商用蓝色荧光粉和近紫外芯片进行封装整合,得到可发射暖白光的WLED器件,其色温和显色指数分别为3843 K和85.8。     

(Ca1-x-yLuy)MoO4∶xEu3+红色荧光粉的化学共沉淀合成与光致发光

使用NH4HCO3-NH3.H2O混合沉淀剂,采用化学共沉淀法合成(Ca1-x-yLuy)MoO4:xEu3+红色荧光粉,通过XRD、EDS、荧光光谱和CIE色度图研究该荧光粉的晶体结构、成分组成及发光性能。结果表明,实验按照理论化学计量比成功合成了(Ca1-x-yLuy)MoO4:xEu3+红色荧光粉,该荧光粉为CaMoO4白钨矿结构;(Ca1-x-yLuy)MoO4:xEu3+具有7F0→5L6(394 nm)和7F0→5D2(465 nm)的强电子吸收,且在613 nm处可发射高强度红光,其色坐标为(0.666 5,0.332 9),明显优于传统的Y2O2S:Eu3+红色荧光粉;此外,当Lu含量为30mol%时,荧光粉发光强度最佳。     

Synthesis,Structure, and Photoluminescence Properties of Novel KBaSc2(PO4)3:Ce3+/Eu2+/Tb3+ Phosphors for White‐Light‐Emitting Diodes

A series of novel KBaSc₂(PO₄)₃:Ce³⁺/Eu²⁺/Tb³⁺phosphors are prepared using a solid‐state reaction. X‐ray diffraction analysis and Rietveld structure refinement are used to check the phase purity and crystal structure of the prepared samples. Ce³⁺‐ and Eu²⁺‐doped phosphors both have broad excitation and emission bands, owing to the spin‐ and orbital‐allowed electron transition between the 4f and 5d energy levels. By co‐doping the KBaSc₂(PO₄)₃:Eu²⁺ and KBaSc₂(PO₄)₃:Ce³⁺ phosphors with Tb³⁺ ions, tunable colors from blue to green can be obtained. The critical distance between the Eu²⁺ and Tb³⁺ ions is calculated by a concentration quenching method and the energy‐transfer mechanism for Eu²⁺→Tb³⁺ is studied by utilizing the Inokuti–Hirayama model. In addition, the quantum efficiencies of the prepared samples are measured. The results indicate that KBaSc₂(PO₄)₃:Eu²⁺,Tb³⁺ and KBaSc₂(PO₄)₃:Ce³⁺,Tb³⁺ phosphors might have potential applications in UV‐excited white‐light‐emitting diodes.     

稀土发光材料在固体白光LED照明中的应用

固体白光发光二极管将成为21世纪新一代的节能光源. 要实现白光发射的重要途径之一是利用稀土发光材料的荧光转换技术, 把InGaN半导体管芯发射的460 nm蓝光或400 nm近紫外光转换成白光. 分别就这两种管芯报道了我们研制的发射蓝、绿、黄、红等不同颜色的稀土发光材料： YAG：Ce, Ca1-xSrxS：Eu^2＋, Ga2S3：Eu^2＋, MGa2S4：Eu^2＋（M=Ca, Sr, Ba）, SrGa^2＋xS4＋y：Eu^2＋, （Ca1-xSrx）Se：Eu^2＋, SrLaGa3S6O：Eu^2＋, （M1, M2）10（PO4）6X2, （M1=Ca, Sr, Ba; M2=Eu, Mn; X=F, Cl, Br）, NaEu0.92Sm0.08（MoO4）2, 并报道了由它们制成的白光发光二极管的色坐标、相关色温和显色指数等参数.