AC losses in a flexible 10 m long conductor model for a HTS power transmission cable

To demonstrate the possibility of manufacturing a HTS power transmission cable with low AC losses, we fabricated a 10 m long cable conductor and a cryosystem. The conductor was wound in a four-layer design out of 2 km Ag/Bi-2223 tapes. We determined a critical current of 5000 A. Loss measurements were performed with an electric method which detects the voltage drop along the conductor with a lock-in technique and a calorimetric method which measures the temperature rise along the conductor. Both methods yield the same low loss values of only 0.8 W/m at 77 K and 2000 A_rms/50 Hz. This is due to the low loss winding scheme we used which assures an equal current distribution in all four layers through transformatoric coupling. We applied the uniform current distribution model and added the nonlinear V–I curve to describe quantitatively the obtained results.     

The transport current redistribution between the core layers on the models of HTS cables

The multilayer conductors with insulated and non-insulated layers are analyzed. The space–time current redistributions between the layers of the conductor are investigated for the next parameters: values of electric resistance at the current leads, transverse contact electric resistance between the layers, the model length, time, the conductor dimension, the current—its peak value, the change law and the ramp of the total current input. Most of the published test results for short (from 1 to 10 m) conductor models do not reflect the true current distribution of the real long length cable conductors. The criterion of experimental model constructions and, in particular, the calculation of its minimum length are presented. The calculations demonstrate the electromagnetic processes in real cable conductors.     

Measurements of AC losses in different former materials

A high temperature superconducting cable may be based on a centrally located cylindrical support, a so-called former. If electrically conductive, the former can contribute to the AC losses through eddy current losses caused by unbalanced axial and tangential magnetic fields. With these measurements we aim at investigating the eddy current losses of commonly used former materials. A one layer cable conductor was wound on a glass fibre reinforced polymer (GFRP) former. By inserting a variety of materials into this, it was possible to measure the eddy current losses of each of the former candidates separately; for example copper tubes, stainless steel braid, copper braid, corrugated stainless steel tubes, etc. The measured data are compared with the predictions of a theoretical model. Our results show that in most cases, the losses induced by eddy currents in the former are negligible. However, for materials with a low resistivity the eddy current losses may become significant, e.g., for high purity Cu or Al.     

脉冲功率电缆的受力分析与结构优化北大核心CSCD

强电磁力是造成脉冲功率电缆损坏的主因,其限制了脉冲功率电缆的通流能力。对同轴电缆导体层的受力情况进行了仿真,探讨了电缆导体结构对脉冲功率电缆通流能力的影响。列举了使用过的一种同轴电缆,分析了该种电缆外导体层的受力情况和结构变化趋势,并讨论了试验结果。进一步对另一种结构的同轴电缆进行了分析和试验,认为其具有更好的抗电磁力能力,试验结果表明,其峰值电流达到208kA,通流能力达到6.9kA/mm^2,验证了这种电缆结构的优越性。     

Anomalous interlayer magnetoresistance in bilayer crystals

The interlayer magnetotransport of a model layered metal is calculated semiclassically. Each layer contains parallel quasi-1D wires but the orientation of wires within each layer is perpendicular to the orientation of wires in adjacent layers. The model has a highly anisotropic amplitude for interlayer electron transfer and is used to illustrate simply the effects that this anisotropy has on the magnetotransport. Strong positive magnetoresistance is calculated for magnetic fields parallel to the current, with the size of magnetoresistance varying inversely with the interlayer hopping amplitude. For fields perpendicular to the current, the magnetoresistance depends qualitatively on the orientation of the field: it scales linearly with the field strength B when the field points toward intersections of 1D Fermi surfaces belonging to individual layers, and scales as √B when the field points between intersections. In a weak field, the resistance is maximum when the field is orientated parallel to the current and minimum when it is perpendicular to the current. Magnetoresistance oscillations are also studied. The implications for more general models of multilayer metals are discussed.     

The similarities in loss creation in LTS and HTS cables

The coupling current losses represent an essential contribution to AC losses in most practical superconducting conductors. The origin of this loss type is well known, being caused by induced currents in different loops consisting of superconducting and non-superconducting parts. However, the ‘current pattern' in different conductor types (strands, flat or round cables, more complicated cable structures, CICC) varies appreciably. These differences are mainly due to geometrical effects (size and shape of filaments and/or strands, their spatial distribution, conductor aspect ratio, demagnetization effects). Although the general knowledge about AC losses in low temperature cable structures is by far not complete (mainly at higher frequencies, in inhomogeneous fields and for inhomogeneous cable structure), an attempt is made to summarize those results which can be adopted to high T_c conductors and some remarks are made about new features of AC losses in these conductor types.     

Single-phase AC losses in prototype HTS conductors for superconducting power transmission lines

We report single-phase AC loss measurements on 8-, 4-, and 3-layer, multi-strand, HTS prototype conductors for power transmission lines. We use both calorimetric and electrical techniques. The agreement between the two techniques suggests that the interlayer current distribution in 1-m long conductors are representative of those in long conductors. The losses for the 8- and 4-layer conductors are in rough agreement, with the 8-layer losses being somewhat lower. The 3-layer conductor losses are substantially higher — probably due to unbalanced azimuthal currents for this configuration.     

Fold amplification rates and dominant wavelength selection in multilayer stacks

A combination of thin- and thick-plate theories, and finite element models is used to systematically analyze folding in multilayer stacks. We show that if the interlayer spacing is large, individual layers fold as single layers, if the spacing is small the entire stack folds as one effective single layer. In between, a third folding mode exists that is characterised by a dominant wavelength that scales with n ^1/3, irrespective of total number of layers, n. The maximum growth rates in the true multilayer-folding mode are higher than the corresponding single layer growth rates, increase with n and are bounded by a saturation value that is directly proportional to the viscosity contrast. This growth rate saturation as well as the applicability of the true multilayer-folding mode with respect to interlayer spacing can be explained by the normal and inverse contact strain theory. The true multilayer-folding mode is expected to be the most frequent mode in nature, because it exhibits the highest growth rates and has a relatively large applicability range with respect to interlayer spacing. The increased growth rates in multilayer folding are especially important for systems where the corresponding single layer values are not sufficient to drive the folding instability, such as folding in low-viscosity contrast layers and detachment folding.     

Improving efficiency of organic light-emitting devices by optimizing the LiF interlayer in the hole transport layer

The efficiency of organic light-emitting devices (OLEDs) based on N,N'-bis(1-naphthyl)-N,N'-diphenyl-N,1'-biphenyl-4,4'-diamine (NPB) (the hole transport layer) and tris(8-hydroxyquinoline) aluminum (Alq₃) (both emission and electron transport layers) is improved remarkably by inserting a LiF interlayer into the hole transport layer. This thin LiF interlayer can effectively influence electrical performance and significantly improve the current efficiency of the device. A device with an optimum LiF layer thickness at the optimum position in NPB exhibits a maximum current efficiency of 5.96 cd/A at 215.79 mA/cm², which is about 86% higher than that of an ordinary device (without a LiF interlayer, 3.2 cd/A). An explanation can be put forward that LiF in the NPB layer can block holes and balance the recombination of holes and electrons. The results may provide some valuable references for improving OLED current efficiency.     

不同基底石墨烯涂层的层间滑移减磨性能研究

石墨烯薄膜作为一种二维材料,是提高微/纳机电系统(MEMS/NEMS)摩擦力学性能的优异润滑剂.为了探究基底材料和石墨烯层数对其减磨性能的影响,本文通过在不同基底制备了不同层数的石墨烯涂层,利用原子力显微镜(AFM)实验和分子动力学(MD)仿真结合的方法,研究了石墨烯层数对减磨效应的影响.并且通过建立不同层数石墨烯涂层的摩擦性能分析模型,探究出石墨烯层间滑移是产生减磨的主要因素.结果表明:在不同载荷下,石墨烯涂层对硅基底和铜基底均有优异的减磨效果,摩擦力随着石墨烯层数的增加逐渐降低,当石墨烯层数大于10层时,达到最优99.3%的减磨效果.通过仿真分析发现,随着层数增加,石墨烯与基底的干摩擦转变为石墨烯的层间摩擦,并产生层间剪切滑移,石墨烯层间滑移是导致多层石墨烯优异减磨性能的主要因素.     

Numerical minimization of AC losses in coaxial coated conductor cables

Power cables are one of the most promising applications for the superconducting coated conductors. In the AC use, only small resistive loss is generated, but the removal of the dissipated heat from the cryostat is inefficient due to the large temperature difference. The aim of this work is to minimize the AC losses in a multilayer coaxial cable, in which the tapes form current carrying cylinders. The optimized parameters are the tape numbers and lay angles in these cylinders. This work shows how to cope with the mechanical constraints for the lay angles and discrete tape number in optimization. Three common types of coaxial cables are studied here to demonstrate the feasibility of optimization, in which the AC losses were computed with a circuit analysis model formulated here for arbitrary phase currents, number of phases, and layers. Because the current sharing is practically determined by the inductances of the layers, the optima were obtained much faster by neglecting the nonlinear resistances caused by the AC losses. In addition, the example calculations show that the optimal cable structure do not usually depend on the AC loss model for the individual tapes. On the other hand, depending on the cable type, the losses of the optimized cables may be sensitive to the lay angles, and therefore, we recommend to study the sensitivity for the new cable designs individually.     

AC losses in circular arrangements of parallel superconducting tapes

The DC and AC properties of superconducting tapes connected in parallel and arranged in a single closed layer on two tubes (corresponding to power cable conductor models with infinite pitch) with different diameters are compared. We find that the DC properties, i.e., the critical currents of the two arrangements, scale with the number of tapes and hence appear to be independent of the diameter. However, the AC loss per tape (for a given current per tape) appears to decrease with increasing diameter of the circular arrangement. Compared to a model for the AC loss in a continuous superconducting layer (Monoblock model) the measured values are about half an order of magnitude higher than expected for the small diameter arrangement. When compared to the AC loss calculated for N individual superconducting tapes using a well known model (Norris elliptical) the difference is slightly smaller.     

Mo/Si多层膜表面保护层设计

为提高Mo/Si多层膜的稳定性与使用寿命,通过分析多层膜驻波电场的分布,对表面保护层及多层膜最上层材料的厚度进行优化设计,使优化后的反射率最高.计算表明,一定厚度的表面保护层总对应一个最优的最上层材料厚度.在13.36 nm波长,膜对数为50的Mo/Si多层膜10度入射的理论反射率为74.47%;当添加厚度为2.3 nm的Ru作为表面保护层,对应多层膜最上层Si的优化厚度为3.93 nm,其理论反射率为75.20％.设计结果表明,通过优化设计表面保护层,可以提高多层膜稳定性,改善多层膜性能.     

CFETR馈线导体设计与热稳定性分析

CFETR馈线导体设计采用NbTi超导线材管内电缆(CICC)结构,其中超导电缆主要由6个花瓣形状的电缆和一个中间铜芯绞制而成,而花瓣形状的电缆由NbTi超导线材与铜线沿顺时针方向通过4级绞制而成,导体外部采用不锈钢铠甲结构。计算分析了运行工况下导体结构的热稳定性参数。结果显示,在95.6kA的最高载流下,分流温度低于6K,热点温度低于250K,满足设计要求。     

Anisotropic plasmon dispersion and damping in multilayer 8-Pmmn borophene structures

We investigate the collective plasma oscillations theoretically in multilayer 8-Pmmn borophene structures, where the tilted Dirac electrons in spatially separated layers are coupled via the Coulomb interaction. We calculate the energy dispersions and Landau dampings of the multilayer plasmon excitations as a function of the total number of layers, the interlayer separation, and the different orientations. Like multilayer graphene, the plasmon spectrum in multilayer borophene consists of one in-phase optical mode and N - 1 out-of-phase acoustical modes. We show that the plasmon modes possess kinks at the boundary of the interband single-particle continuum and the apparent anisotropic behavior. All the plasmon modes approach the same dispersion at a sufficiently large interlayer spacing in the short-wavelength limit. Especially along specific orientations, the optical mode could touch an energy maximum in the nondamping region, which shows non-monotonous behavior. Our work provides an understanding of the multilayer borophene plasmon and may pave the way for multilayer borophene-based plasmonic devices.     

Electro-mechanical behavior of single twisted high-temperature superconducting tape under transverse Lorentz force

In recent years, several cabling methods of high temperature superconducting (HTS) cable have been proposed; e.g., the conductor on a round core cable (CORC), the Roebel assembled coated conductor cable, the helical twisted stacking-tape cable (TSTC) and the twisted-stack slotted core HTS cable (TSSC). These cabling methods allow the high temperature superconducting tapes widely used in the high-field magnets. The single superconducting tape performance under applied loads directly relates to the transport performance of the cable and the choice of the cabling method. In this paper, we investigate the effect of twisting morphology on the electro-mechanical properties of HTS tapes. Particular attention is given to the transverse Lorentz force of a pre-twisted HTS tape. The analytical solution of the deflection of the HTS tape under transverse Lorentz force is derived. Then, the current distribution and AC loss of the tape are calculated by using H-formulation. The effects of twist angle and loading conditions are examined for different HTS tape lengths. The results show that the stiffness resistance ability to Lorentz force of the HTS tape can be increased in several ranges by increasing the twist angle. The twisting structure can also reduce current degradation and AC loss, and thus enhance the transport capacity of HTS tape. This study helps understand the electro-mechanical properties of pre-twisted HTS tapes and provides theoretical reference for the design of novel HTS cable structures.     

同轴电缆连续波电磁辐照的终端负载响应

为了揭示设备互连电缆在连续波电磁辐照条件下的耦合响应规律,以典型射频同轴电缆为受试对象,将电缆终端连接的设备（系统）等效为负载,通过对其进行连续波电磁辐照效应试验研究,分析了受试电缆长度、终端负载状态等对同轴电缆终端负载响应规律的影响。结果表明:同轴电缆对电磁辐照响应具有选频特性,终端负载响应电压的峰值出现在电缆相对长度为1/2整数倍的频点;同轴电缆受到连续波电磁辐照后,感应皮电流通过转移阻抗转化为芯线与屏蔽层之间的差模感应电压,而这一感应电压源的内阻就是同轴电缆的特性阻抗;同轴电缆终端负载阻值的变化不会对其连续波辐照响应曲线的变化规律产生影响,终端负载与等效感应电压源内阻上的电压响应满足分压原理; 同轴电缆皮电流处于谐振状态时,两波节之间的分布感应电压同向,可等效为一个感应电压源,对同轴电缆终端负载响应起直接作用的电压源是最靠近终端负载的等效感应电压源。     

Interlayer superfluidity in bilayer systems of fermionic polar molecules

We consider fermionic polar molecules in a bilayer geometry where they are oriented perpendicularly to the layers, which permits both low inelastic losses and superfluid pairing. The dipole-dipole interaction between molecules of different layers leads to the emergence of interlayer superfluids. The superfluid regimes range from BCS-like fermionic superfluidity with a high Tc to Bose-Einstein (quasi-)condensation of interlayer dimers, thus exhibiting a peculiar BCS-Bose-Einstein condensation crossover. We show that one can cover the entire crossover regime under current experimental conditions.     

Amplitude and phase characteristic of x-ray mirrors

The effect of absorption, interlayer roughness, and fluctuations of the layer thicknesses on the phase-shifting and polarization properties of multilayer structures has been investigated on the basis of coupled-mode equations. The conditions for the parameters of multilayer structures that make it possible to achieve the best phase-shifting characteristics of mirrors are formulated.     

大型超导电缆交流损耗的计算

给出了超导电缆交流损耗的表达式。使用这些表达式 ,并基于 HT- 7U极向场线圈系统在等离子体建立时的电流波形 ,计算了 AC损耗在 PF导体上的能量沉积。最后讨论了电缆参数对AC损耗的影响